Flanging and dishing machine GRAAF HVP

Graaf HVP 300

Condition: as good as new (ex-display), Year of construction: 2023, Container rotating device, 10-ton lifting capacity Speed: continuously adjustable Hand and foot remote control Diameter: 320mm to 2800mm Roller diameter: 300mm Lsdjd Nmx Tjpfx Ab Aohn Speed: 6 - 60 m/h Power: 2 x 0.55 kW

Year of construction: 2012, condition: excellent (used), Alfa Laval Centrifugal pump Type LKH 85/240, 25,0 kW , Stainless Steel. Used! Good condition! Lsdpfx Abshck S Ej Ajhn Inlet: 6" - Outlet: 6"

Year of construction: 1985, condition: reconditioned (used), Technical Details : Wire Dimeter range- 4-12mm Gscxckebw Run out table - 4m Speed -80' m/min. Lhjdpfx Aeh In Thob Aon Reconstruction- 2022

Condition: excellent (used), Year of construction: 2010, operating hours: 75,000 h, functionality: fully functional, 55 kW compressor with built-in dryer and frequency inverter. Very good condition. After service. 3 months warranty. Lhjdpfjv Rmmmex Ab Ajn

Condition: used, Power source for orbital welding machine MESSER GRIESHEIM - POLYSOUDE PS204 Water cooling unit for orbital welding machine MESSER GRIESHEIM - POLYSOUDE RC200 Welding power source, inverter welding machine POLYSOUDE PS 204 + RC 200 Year of manufacture: 1997 Power source serial no.: 9885186 Lodjt Awm Djpfx Ab Aehn Cooling unit serial no.: 97861? Output: 200 amps = 20% duty cycle 90 amps = 100% duty cycle Power supply: 230 volts, 50 Hz, Schuko plug - Remote control cable type BP 1436 with 7.5 m connection cable - Adjustable output from 1 to 200 amps - DC only - HF ignition - Cooling water unit for torch cooling - 44,895 operating hours (read) - Operating and maintenance manual included Space requirements welding machine (L x W x H): 550 x 360 x 500 mm Space requirements cooling unit (L x W x H): 550 x 360 x 550 mm Weight welding machine: 45 kg Weight cooling unit: 25 kg Good condition Sold without accessories The price refers to a set consisting of 1x power source and 1x water cooler.

Condition: used, Table unit from a DROOP & REIN portal milling machine Clamping plate with T-slots made of cast steel gray cast iron Table unit with clamping plate and very solid guideway Table clamping surface 5500 x 2000 mm Travel of the table clamping plate approx. 3100 mm Table height 1050 mm Table load: max. 20 tons Ball screw: Ø 100 mm Thread pitch: 20 mm (single-start) - Processing table guided very stably on the bed Lhjdpfjthuzpjx Ab Ajn - Metal telescopic guideway cover - comes from a DROOP & REIN portal milling machine - Longitudinal table movement via ball screw and SIEMENS servo motor - Clamping surface with 11 T-slots 28 mm - Drive via SIEMENS 1FT6134-6AB71-1AG2 servo motor with IC200448S/R encoder (RN 000 B25) Total length 9500 mm Width 2000 mm Overall height 1050 mm dead weight 28 ton. good condition

Condition: refurbished (used), ECCENTRIC PRESS SGP TYPE : PEZZ 500/1700/1000 PRESSURE : 500t DOWN TABLE DIMENSIONS: 1700x1000mm LENGTH OF STROKE: 20-153mm DISTANCE BETWEEN RAM -TABLE: Min 700mm , Max 800mm WEIGHT: 40.000 kgr MADE IN AUSTRIA Lhedpfx Abjhqqnzs Aen

Condition: excellent (used), Year of construction: 1985, functionality: fully functional, pressing force: 4,000 t, 5. Forging hammer SMERAL type KJH 4 Weight of the ram, kg: 1’800 Ram impact rated energy, kgm: 4’000 Lsdpfowbginjx Ab Ashn Number of ram strokes,1/min: 48 Ram stroke, mm: 500 Die camping area, mm: 286 x 600 Min. Die Height, mm: 350 Output of main motor, kW: 45 Lenght of the machine, mm: 3’100 Widht of the machine, mm: 1’900 Height of the machine, mm: 3’900 Weight of the machine, kg: 27’000

Condition: used, Year of construction: 1986, pressure 160 t Lhjdpfx Abjv Rgwxo Aen throat 360 mm stroke 500 mm feed down 200 mm/sec feed up 125 mm/sec max. distance table - ram 1000 mm table surface area 900 x 630 mm ram surface 850 x 450 mm clamping pivot 50 H7 / 85 mm total power requirement 17 kW weight of the machine ca. 7 t dimensions of the machine ca. BxTxH 1,25 x 2,2 x 3,45 m

Condition: good (used), Year of construction: 1984, max. wheel diameter 250 mm gear width 275 mm max. module 6 weight of the machine ca. 5,5 t The gear hobbing machine ZFWZ 250 is suitable for the economical production of all hob-processable cylindrical gear types, such a: - spur and helical gear, wormgears and worms, splined shafts, keyed shafts, serrated profiles, chain wheels and ratchet wheels,as well as conical and crowned spur and helical gears. Interchangeable wheels and milling accessories Technical data: - Workpiece diameter (max): 250 mm - Module (max): 6 mm - Axial feed travel (max): 275 mm - Tangential feed travel (max): 100 mm - Tooth helix angle (max): 45 degrees - Milling cutter diameter (max): 145 mm - Milling cutter length (max): 170 mm - Table clamping surface (min): 195 mm - Table clamping surface (max): 470 mm Power Milling cutter speeds - Stepped in 2 ranges: 56 ... 250 rpm - (Standard version): 90 ... 400 rpm - Infinitely variable in 2 ranges: 63 ... 180 rpm - (special version DC motor): 140 ... 400 rpm Weights - Machine net: approx. 5000 kg - Electrical cabinet: approx. 800 kg - Hydraulic unit + coolant tank + chip transport: approx. 700 kg Overall dimensions (with oil mist filter) - Length: Standard version: 3950 mm DC drive: 3450 mm (or 3350 mm according to table) - Width: 3300 mm - Height: Machine: 1980 mm Machine with DC drive: 2150 mm Ledpfx Abjv T Nqaj Ajhn Electrical cabinet: 2200 mm