Used other drilling machines and boring mills for sale (47)

Year of construction: 1985, condition: used, Drilling process: single-lip gundrilling, operating method: rotating tool, number of working spindles: 1, nominal drilling depth: approx. 750mm, drilling range for solid drilling in steel: approx. 30mm, drilling range for counterboring in steel: approx. 40mm, spindle drive: 11kW, max. spindle speed range I: 1800rpm, max. spindle speed range II: 5700rpm, max. feed rate range I: 320mm/min, max. feed rate range II: 160mm/min, rapid traverse: 3.5m/min, clamping table X/Y: 420mm/1280mm, cross-slide table manually operated, max. transverse travel: 400mm, table clamping surface X/Y: 600mm/600mm, high-pressure coolant system for deep-hole drilling oil with 1000l coolant tank, flow rate: approx. 2-94l/min, max. pressure at max. flow rate: 45bar, pump power: 11kW, separate control cabinet. The machine underwent an extensive partial overhaul in 2018, during which the machine was disassembled and cleaned, all guideways and support surfaces were ground and partially scraped, motors were inspected and fitted with new bearings, the drilling spindle was fitted with new bearings, the ball screw incl. nut was replaced, the pump motor was overhauled, the wiper set was replaced, and the machine was repainted and all functions were checked and rectified. Including extensive accessories. Documentation available. Inspection possible by arrangement. Isdozu Szyopfx Abnstk

Year of construction: 1999, condition: used, Max. drilling diameter in steel, strength 600MPa: 50mm, max. drilling diameter in cast iron, strength 250MPa: 60mm, max. boring diameter (with guide) in steel, 600MPa: 200mm, max. thread in steel, 600MPa: M50x1.5, max. thread in cast iron, 250MPa: M60x2, spindle reach: 320-1250mm, pitch circle of holes: 1208-3039mm, distance from spindle axis to base plate: 320-1380mm, max. arm height adjustment: 750mm, max. drill carriage travel on arm: 930mm, arm swivel range: +/-180°, spindle head diameter: 75h6, spindle diameter at front bearing: 55mm, length: 2900mm, width: 1120mm, height: 3271mm, weight: 4.2t, with documentation. An on-site inspection is possible. Itedpfx Ajzuzziebnok

Year of construction: 2002, condition: ready for operation (used), Travel X/Y/Z: 3000mm/2300mm/1600mm, travel W: 700mm, max. table-to-spindle distance: 2300mm, table dimensions X/Y: 1800mm/2200mm, max. table load: 10000kg, spindle diameter: 130mm, spindle speed: 2500rpm, rapid traverse X/Y/Z: 10m/min, rapid traverse W/B: 5000mm/min/500mm/min, feed X/Y/Z: 4m/min, tool holder: BT50, tool positions: 38, positioning accuracy X/Y/Z: +/-0.008mm, positioning accuracy W: +/-0.012mm, repeatability X/Y/Z: +/-0.004mm, repeatability W: +/-0.008mm. Machine dimensions X/Y/Z: approx. 7050mm/7200mm/4800mm, weight: approx. 37000kg, control: TOSNUC-888. Documentation available. An on-site inspection is possible. The machine is located in China. Itsdpfxexf Ikro Abnek

Year of construction: 1980, condition: ready for operation (used), A Gebrüder Irle CNC large-format deep-hole drilling machine is available. Drilling capacity steel: 40mm, max. drilling depth: 1600mm, drill spindle adjustment: 350mm, vertical drilling unit adjustment: 700mm, power: 30kW, speed: 2940rpm, field range constant power: 1-3, armature range constant torque: 1-35, max. drill spindle torque: 1500Nm, rated speed: 163rpm, spindle flange diameter: 200mm, quill diameter: 2000mm. Feed: 500mm/min, rapid traverse: 1200mm/min, max. feed force: approx. 34.3kN, display: 0.005mm, vertical adjustment travel: 700mm, longitudinal adjustment travel: 13000mm, transverse adjustment travel: 650mm, swivel: 85°. Clamping plate dimensions X/Y/Z: 12500mm/1000mm, guide bed dimensions X/Y: 3350mm/455mm, controls: Heidenhain TNC 310. Documentation available. An on-site inspection is possible. Isdpfoy Rtfzox Abnetk

Year of construction: 2007, condition: ready for operation (used), A CNC profile drilling machine Voortman with a movable drilling cabin is available. Working height range: 30mm-1050mm, positioning speed: 40m/min, table width: 300mm, max. working width: 1800mm, support depth: 1500mm, tool stations: 5, max. travel speed: 40m/min, tool holder: SK40, drilling diameter range: 5mm-40mm, thread cutting range: M6-M30, working length: 16200mm. Documentation available. On-site inspection possible. Itjdpjxp Rb Ijfx Abnjk

Year of construction: 1987, condition: ready for operation (used), A complete Wagner WBX 1003 boring mill is available. Control: CNC Systems WB 1000, documentation is available. Iodpottv Uajfx Abnotk

Year of construction: 1970, condition: ready for operation (used), A horizontal boring and milling machine Scharmann is available. Spindle sleeve diameter: 120mm, travel X/Y/W: 1600mm/1600mm/600mm, speed: 1000rpm, table dimensions X/Y/Z: approx. 1200mm/1400mm, max. table load: 6000kg, column diameter: 220mm, table rotation: 360°, rapid traverse: 380mm/min, feed: 2400mm/min. Machine dimensions X/Y/Z: approx. 4500mm/2600mm/3000mm, weight: approx. 17000kg. Dokumentation vorhanden. An on-site inspection is possible. Itjdexyk Tlspfx Abnek

Year of construction: 2018, condition: ready for operation (used), A CNC radial drilling machine overhauled in 2018 is offered. Working range X/Y: 1050mm/1800mm, drilling capacity steel: 40mm, drilling capacity cast iron: 50mm, thread cutting: M36-M45, tool holder: SK40, speed range: 15rpm-2800rpm, quill stroke Z: 200mm, column stroke W: 410mm, table clamping surface X/Y: 1800mm/600mm, feed speed: 5mm/min-2000mm/min, rapid traverse X/Y: 7.5m/min, control: CNC control. Equipped with 360° swivel device, motorized tool clamping, three-jaw chuck for round parts, modernized LCD monitor, extensive tooling package. Weight: approx. 2900kg, overall dimensions X/Y/Z: approx. 2600mm/1900mm/2950mm. Inspection possible by arrangement. Iedpfxey Tn Nte Abnotk

Condition: ready for operation (used), Drilling capacity (steel): 100mm, max. pitch circle diameter: 7000mm, spindles: 2, spindle speed: 3000rpm, spindle mount: ISO 50, drill carriage stroke: 900mm, feed: 6m/min, power: 125kW. Machine dimensions X/Y/Z: approx. 13000mm/11000mm/5100mm, weight: approx. 18000kg. On-site inspection is possible. Itodpfovriq Rox Abnok

Year of construction: 2011, condition: ready for operation (used), Various metalworking machines, including a larger Wagner radial drilling machine, are available. 1) Column radial drilling machine Wagner PRC 50, year of manufacture: 2011, drilling capacity (steel): 50mm, spindle stroke: 315mm, outreach range: 350mm-1600mm, spindle-base plate distance: 370mm-1270mm, speed: 2000rpm, machine dimensions X/Y/Z: approx. 2500mm/1100mm/2900mm, weight: approx. 3500kg. The machine has an unknown defect. 2) Column drilling machine Alzmetall AX3/SV, year of manufacture: 2000, drilling capacity (steel): 32mm, spindle stroke: 120mm, outreach: 293mm, column diameter: 115mm, table dimensions X/Y: 515mm/360mm, speed: 2250rpm, weight: approx. 300kg. 3) 2x metal circular saw Macc NTM 350, year of manufacture: 1998/2010, saw blade diameter: 350mm, cutting capacity: 120mm, weight: approx. 450kg. 4) Belt grinding machine Grit A/S GIS 150, year of manufacture: 2014, belt dimensions X/Y: 150mm/2000mm, motor power: 4kW, weight: approx. 100kg. An on-site inspection is possible. A package sale is preferred. Isdpfx Abjy Eqtisnjtk

Condition: ready for operation (used), Drilling diameter: 3-25mm, drilling depth: 1000mm, connected load: 36kW, control: EST, 99 drilling memory positions per program, grinding and coordinate programming, plain text programming via input mask. Accessories: paper band filter, coolant cooling system, 4-door control cabinet, high-pressure pump up to 150bar, oil tank, 1 steady rest for smaller diameters at large drilling depths, direction-adjustable holder for drill bushing holders, various drill bushing holders, long clamping table for 0-height, tailstock stop and base plate for machine vice freely movable on the additional table, matching precision machine vice optionally available. Speed, high pressure, Z-axis (feed), X/Y-axes, and W-axis (approach slide) programmable via control. CPU and card rack defective (fan fault), machine therefore not operational, drives and guideways were fully functional until last operation. An on-site inspection is possible. Iedjylbrqjpfx Abnetk

Year of construction: 1981, condition: ready for operation (used), Travel X/Y/Z/W: 1000mm/900mm/800mm/710mm, speed: 1400rpm, spindle diameter: 90mm, table dimensions: 1250mm/1250mm, max. table load: 3000kg, motor power: 7.5kW. X/Y dimensions: approx. 5500mm/7500mm, weight: approx. 11000kg, control: Newall DP700. Documentation available. Iodpjt Hkh Aofx Abnetk

Year of construction: 1991, condition: ready for operation (used), Available immediately, ex works: Drill press, Metalac Type BR 32 Year of manufacture 1991 Spindle taper MK 3 Drilling capacity: 32 mm steel, 40 mm cast iron Automatic feed Table: 600 x 470 mm Itedpfx Abjzukgzsnsk Drilling stroke: 180 mm Overhang: 280 mm 2 vices Coolant system Weight: 750 kg Price: EUR 1,250.00 plus VAT, ex works.

Condition: used, Year of construction: 1984, Used Horizontal borer TITAN AFL 150 CNC CNC Heidenhain - X column - 9000 mm; - Y vertical - 2000 mm; Itsdob Hv Twspfx Abnjk - W spindle - 900 mm - Z column cross - 600 mm - spindle speed 900 rpm - spindle dia. 150 mm - Machine weight aprox. 50 tons Floor plates 2 pcs. 2000x6000 Rotary table Skoda E20

Condition: ready for operation (used), Year of construction: 1978, travel distance X-axis: 8,300 mm, travel distance Y-axis: 2,500 mm, travel distance Z-axis: 500 mm, Floor boring machine WMW Union BFP 130/5 X-axis: 8300mm Y-axis: 2500mm Itodpfx Aezt Iqbebnjk Z-axis: 500mm W-axis: 900mm Spindle diameter: 130mm Spindle taper: ISO 50 Rotary table: 2000x1800 2 x floor plates: 3500x1750 Year of manufacture: 1978 Milling head Tailstock DRO Heidenhain Spindle stabilizer Boring bar Many accessories ✅ Excellent working condition Total weight: 53 tones

Year of construction: 1995, condition: ready for operation (used), travel distance X-axis: 1,500 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 1,000 mm, controller manufacturer: FANUC, spindle speed (max.): 1,600 rpm, number of axes: 5, This 4-axis WOTAN Rapid 1 boring machine was manufactured in 1995 and retrofitted in 2017. It features an impressive X-axis travel of 1,500 mm, Y-axis travel of 1,000 mm, and Z-axis travel of 1,000 mm. The 360° rotary table allows for multi-sided machining, enhancing efficiency. If you are looking to get high-quality boring capabilities, consider the WOTAN Rapid 1 machine we have for sale. Contact us for further details. • B-axis (rotary table): 360°; max weight capacity 4 tons • Key highlights: • 360° rotary table enables multi-sided machining in a single setup, reducing downtime and improving tolerances • 2017 Fanuc control retrofit offers a modern interface and compatibility with current programming standards Technical Specification Taper Size BT 50 Iedozqb Eaepfx Abnetk

Year of construction: 2025, condition: new, functionality: fully functional, machine/vehicle number: 60176, New pneumatic self feed drill unit with 2 signal transmitters and their holders good for drilling or milling Speed (r.p.m. no load): 32,000 rpm Stroke: 40 mm dashpot: 15 mm Motor power: 0.25 kW Total length: 10.63 In. Operating pressure: 5.5 bar lubricated compressed air Suitable for collets (not included) with diameters of 3 to 8 mm Iodpov Tnh Refx Abnstk Included are 2 signal transmitters (24 V DC, M8 connector, 5 m cable) and holders Other versions (speeds, stroke, etc.) are available upon request.

Year of construction: 2014, condition: ready for operation (used), travel distance X-axis: 1,600 mm, total width: 1,250 mm, total height: 3,437 mm, spindle motor power: 5,500 W, product length (max.): 3,080 mm, spindle speed (max.): 1,600 rpm, number of axes: 3, This 3-axis M+A RB 63/20 W drilling machine was manufactured in 2014. It features a maximum drilling diameter of 63 mm in steel and 80 mm in cast iron, with a maximum reach from the column of 2000 mm. The machine includes a robust cube table measuring 800 x 630 x 500 mm. If you are looking to get high-quality drilling capabilities, consider the M+A RB 63/20 W machine we have for sale. Contact us for further details. Ijdpfszk Ivxjx Abnotk - Maximum drilling diameter in steel (600 MPa): 63 mm- Maximum drilling diameter in cast iron (250 MPa): 80 mm- Maximum reach from column: 2000 mm- Minimum reach from column: 450 mm- Column diameter: 450 mm- Minimum distance between spindle nose and baseplate: 400 mm- Maximum distance between spindle nose and baseplate: 1600 mm- Spindle inner taper: MT 5- Maximum spindle stroke: 400 mm- Vertical adjustment of drill head: 800 mm- Horizontal adjustment of drill head: 1550 mm- Baseplate length: 2900 mm- Baseplate width: 1250 mm- Baseplate height: 260 mm- Number of spindle speeds: 16 (hydraulically set)- Spindle speed range: 20 to 1600 rpm (20, 32, 50, 63, 80, 100, 125, 160, 200, 250, 315, 400, 500, 630, 1000, 1600 rpm)- Number of spindle feeds: 16- Spindle feed sizes range: 0.04 to 3.2 mm/rev- Maximum permissible torque at spindle: 980 Nm- Main drive motor power: 5.5 kW (1500 rpm)- Arm elevating motor power: 2.2 kW (1500 rpm)- Clamping motor power: 0.75 kW (1500 rpm)- Coolant pump power: 90 W / 0.09 kW (3000 rpm, Flow rate: 25 l/min, Head: 4 m)- Machine total power: 8.45 kW- Operating voltage: 400 V / 50 Hz- Required connection current: 16 A- Maximum load capacity/weight: Approx. 7000 kg- Machine overall dimensions: 3080 x 1250 x 3290 mm (Max height up to 3437 mm)- Noise emission level: ≤ 85 dB (A)

Year of construction: 1985, condition: used, spindle diameter 110 mm x-travel 900 mm y-travel 600 mm z-axis 200 mm table length 1020 mm table width 860 mm Itedet Hwyxopfx Abnsk taper MK 40 Table size, approx. 1,020 x 860 mm Max. weight of workpiece 800 kg Table travel, longitudinal, max. (X) 900 mm Boring head travel, cross, max. (Y) 600 mm Boring spindle stroke (Z) 200 mm Vertical travel of cross beam (W) 635 mm Vertical distance between table and boring spindle 15 - 850 mm Distance between columns 950 mm Spindle Ø 110 mm Spindle taper internal/external ISO 40 18 spindle speeds 10 - 2,500 rpm Milling feeds of table, infinitely variable 1 - 6,000 mm/min 4 milling feeds of boring head 30 - 180 mm/min 6 boring feeds 0.01 - 0.39 rpm Accuracy of all 3 axes when the machine was new 0.003 mm Quick feeds for table, boring head slide, and boring spindle, max. 6,000 mm/min Spindle drive 6.2 kW Weight, approx. 9,000 kg Total electrical load 15 kW - 380 V - 50 Hz Accessories / Special Features - BOSCH CNC Control, Model MICRO 8, in 3 axes, with monitor. Program input is either manual or via cassette, or via interface entry. - Digital display for Z Axis. - Separate switch cabinet. - Various tools. - Oil cooler for spindle lubrication.

Year of construction: 2009, operating hours: 3,093 h, condition: ready for operation (used), travel distance X-axis: 1,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 1,800 mm, controller manufacturer: HEIDENHAIN, controller model: TNC 320, overall weight: 8,900 kg, total width: 3,400 mm, total height: 3,160 mm, product length (max.): 5,800 mm, spindle speed (max.): 1,600 rpm, table load: 2,500 kg, number of axes: 5, This 5-axis MSC Chemnitz BFT90/5 MSC boring machine was manufactured in 2009. It features a substantial table size of 1000 x 1120 mm with a maximum table load of 2.5 t. The machine offers impressive feed rates of 4000 mm/min and a spindle speed range of 4 – 1600 rpm. If you are looking to get high-quality boring capabilities, consider the MSC Chemnitz BFT90/5 MSC machine we have for sale. Contact us for further details. • Table size: 1000 x 1120 mm • B axis (table rotation): 360° • Feed rate (X/Y/Z): 4000 mm/min • Spindle diameter: 90 mm • W axis travel: 710 mm • Control cabinet dimensions (L x W x H): 2.0 x 0.75 x 2.0 m • Temperature range: 15–40 °C • Electrical: 3-phase/50 Hz; 380 V rated voltage; 24 V control voltage • Connected load: 40 kW • Fuse rated current: 100 A • Typical power consumption: approx. 7.5 kW • Spindle running time: 3069 h • Power-on hours: 10402 h • General overhaul: 2009 General Information Retrofit Retrofit includes: • Control system: TNC 320 • New drives in all axes • New table • New clamping system • New media units • New hand control unit • New coolant system • New hydraulic unit • 30 measuring scales (linear measurement systems) • Control manufacturer: SK 40 • CNC control: TNC 320 • Complete electrical retrofit • New wiring throughout the machine • Integration of CNC system (TNC 320) • New inputs and outputs (I/O) • New sensors and measuring systems • Updated control circuits and safety circuits • Modern CNC control system • Improved accuracy due to new measuring systems Isdpfxey Hvgte Abnjtk • Higher reliability • Better performance due to new drives • Reduced downtime due to new auxiliary units • New electrical documentation • Updated schematics • Includes systems for power supply, control, machine interface, operator panel, and drivesMachine base remains:MSC Chemnitz table boring machineType: BFT 90/5 MSC – 5 axes Technical Specification Taper Size SK 40

Year of construction: 2007, condition: ready for operation (used), travel distance X-axis: 3,500 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 1,220 mm, number of axes: 5, This 5-axis TOS Varnsdorf WHN130 was manufactured in 2007. It features a horizontal boring and milling machine with a table size of 1600 × 1800 mm and a spindle diameter of 130 mm. The machine includes a rotary table and is controlled by an NCT-104 system. Consider the opportunity to buy this TOS Varnsdorf WHN130 boring machine. Contact us for more information. Itjdpfex Imtasx Abnjk • Control system: NCT-104 Spindle • Spindle diameter: 130 mm • Taper: ISO 50 (7:24) • Spindle speed range: 10 – 1500 rpm • Max spindle torque: approx. 2350 Nm • Main motor power: 37 kW Axis Travels • X-axis travel: 3500 mm • Y-axis travel: 2000 mm • Z-axis travel: 1220 mm • W-axis (spindle quill travel): 570 mm Table • Rotary table size: 1600 x 1800 mm • Max workpiece weight: 12,000 kg • T-slots: 22 x 9 x 160 mm • B-axis table feed: 0.03 – 1.5 rpm Feed Rates • Rapid traverse (X / Y / Z / W): 2000 mm/min Power • Total power requirement: approx. 80 – 83 kVA

Condition: new, functionality: fully functional, Fervi T047/400VDA geared drill and milling machine, tapping function, 400V, 1.5kW NEW, “CE” certified. Promotional price – limited availability, subject to prior sale. The machine can be used for the following operations: Milling Drilling Tapping. Drilling capacity in cast iron with pre-drilled hole: ø 40 mm. Maximum drilling capacity in steel with pre-drilled hole: ø 32 mm. Milling capacity with insert cutter: ø 80 mm. Milling capacity: ø 25 mm. Tapping capacity: Ø 22 mm. Isdpfx Absg Npiwenetk Taper attachment: CM 4. Spindle stroke: 130 mm. Spindle housing: ø 76 mm. Column: ø 115 mm. Head tilt: ± 60°. Spindle speed: (12) 75 ÷ 3200 rpm. Three-phase motor: 400 V 50 Hz 1.1 – 1.5 kW. Table dimensions: 585 x 190 mm. T-slot: 12 mm. Base dimensions: 648 x 412 mm. Overall dimensions: 740 x 790 x 1960h mm Weight: 390 Kg.

Year of construction: 2007, condition: like new (used), FICEP 601 DZB CNC DRILLING LINE with 4 way SCRIBING FACILITY I-Beams (without camber): Web height minimum 60mm maximum 610mm. Flange width minimum 30mm maximum 310mm. UNP Channels (web downwards): • Web height minimum 60mm maximum 610mm. Flange width minimum 30mm maximum 300mm. Angles • Flange height (unequal flanges as well) minimum 50 x 50 x 5mm maximum 250 x 250 x 40mm. Flats • Width minimum 100nn maximum 610mm. Itjdpfjh N Taasx Abnjk Square tubes • Size minimum 60 x 60mm maximum 300 x 300mm. Rectangular tubes • Size minimum 60 x 30mm maximum 600 x 300mm. All beams • Maximum thickness that can be drilled 50mm. Maximum length (infeed) 12000mm.

Year of construction: 2012, condition: excellent (used), 3 Spindle. 21 Metres of In‐feed rollers. 21 Metres of Out‐Feed Rollers. 1.25 metres Sections. Roller Feed measuring. Cross Transfers. Itodpfx Ajh Rrxpsbnjk

Year of construction: 2007, condition: good (used), Danobat CNC Drilling / Sawing Line – Year 2007 Single Rotating Spindle. 18 metres In- Feed Rollers. 12 metres Out- Feed Rollers. Pincher Unit Feed. Infeed Cross Transfers. Outfeed Cross Transfers. 750mm Capacity. Iodoig T Amepfx Abnjtk Sawing Capacity: Round cutting capacity(without vertical jaws, angle 0 degrees) 520 mm. Rectangular cutting capacity (without vertical jaw, angle 0 degrees) 700mm X 500 mm. Maximum capacity with vertical jaws 700 X 500 mm. Round cut capacity with 45 degree turn, 450 mm. Rectangular cutting capacity with 45 degree turn, 450 X 500 mm.