Condition: ready for operation (used), Year of construction: 2006, machine/vehicle number: 4547, functionality: fully functional, operating hours: 5,049 h, total height: 2,550 mm, total length: 5,900 mm, total width: 1,350 mm, overall weight: 3,000 kg, plate height: 45 mm, TECHNICAL DETAILS The machine consists of 8 processing units as follows: 1. Unit: Pre-milling unit – tools available 2. Unit: Gluing unit 3. Unit: Pressure rollers – tools available 4. Unit: End trimming unit – tools available 5. Unit: Rough milling unit – tools available 6. Unit: Edge rounding unit – tools available 7. Unit: Radius profiling unit – tools available 8. Unit: Brushing unit – tools available Panel thickness min.: 6 mm Panel thickness max.: 45 mm Panel width min.: 60 mm Panel length min.: 180 mm Feed rate control: Continuously variable Gluing system: Glue pot Voltage: 400 V Power consumption: 53.31 A Iedpfozrmtfjx Al Soba Fuse: 63 A Dimensions & Weight Dimensions (L x W x H): 5,900 x 1,350 x 2,550 mm Shipping weight: 3,000 kg Note: The top and bottom stripping blades are currently not functional.

Condition: used, Year of construction: 2017, power: 20 kW (27.19 HP), edge thickness (max.): 12 mm, feed rate X-axis: 20 m/min, The machine has the following configuration: Pre-milling unit End-capping unit Number of motors in end-capping unit: 2 Ibedezmtldepfx Al Soa Rough milling unit, top and bottom Number of motors in rough milling unit: 2 Edge rounding unit Number of motors in edge rounding unit: 2 Edge trimming unit Glue application unit Edge finishing unit Number of motors in edge finishing unit: 2 TECHNICAL DETAILS Workpiece processing Min. board thickness: 8 mm Max. board thickness: 60 mm Min. edge thickness: 0.4 mm Max. edge thickness: 12 mm Max. feed rate: 20 m/min MACHINE DETAILS Total connected load: 20 kW EQUIPMENT Preheating lamps for workpiece sides Edge roller magazine Glue reservoir for EVA hot melt adhesive Spray unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photographic documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7981

Condition: used, Year of construction: 2008, power: 41 kW (55.74 HP), edge thickness (max.): 3 mm, controller model: ICOS OPEN, The machine has the following configuration: Pre-milling unit Manufacturer model: R3 L20 Engagement control: Automatic, time-controlled Motor power: 4 kW Speed: 9,000 rpm Edge processing Number of edge processing units: 10 Crosscut saw unit Manufacturer model: 8.42/39/B Number of motors: 2 Motor power: 0.6 kW Speed: 12,000 rpm Flush trimming and rounding unit Manufacturer model: 08.055 Number of motors: 0.6 (?) Motor power: 1 kW Speed: 12,000 rpm Corner rounding unit Manufacturer model: 08.342 Number of motors: 2 Motor power: 0.66 kW Speed: 12,000 rpm Scraper blade unit Manufacturer model: 08.50 Belt sanding unit 1 Manufacturer model: 08.62 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 2 Manufacturer model: 08.062 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 3 Manufacturer model: 08 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 4 Manufacturer model: 08.617-2 Motor power: 0.18 kW Speed: 1,400 rpm Belt sanding unit 5 Manufacturer model: 08 Processing unit 10 Manufacturer model: 08.190 Motor power: 4.5 kW Speed: 9,000 rpm TECHNICAL DETAILS Workpiece dimensions Max. panel height: 60 mm Iedpfx Aozmtkael Ssba Min. panel length: 130 mm Min. panel width: 65 mm Edge material Min. edge thickness: 0.4 mm Max. edge thickness: 3 mm Feed Max. feed rate: 30 m/min Pressure: Rubber belt Number of panel sizing/milling units: 1 MACHINE DETAILS Control system: ICOS OPEN Total connected power: 41 kW EQUIPMENT Number of panel sizing/milling units: 1 Lamps for preheating the panel side Edge roller magazine with 2 positions PUR pre-melting unit Pressure roller set with 5 pressure rollers Spraying unit The machine is sold and delivered in its actual and legal condition ("as is, where is") based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at its destination. External reference: 5657

Condition: used, Year of construction: 2014, edge thickness (max.): 12 mm, feed rate X-axis: 18 m/min, TECHNICAL DETAILS Workpiece Dimensions Min. panel height: 10 mm Max. panel height: 60 mm Min. panel width: 70 mm Min. edge thickness: 0.4 mm Max. edge thickness: 12 mm Max. feed rate: 18 m/min Feed and Guidance Pressure with idler rollers Panel support guides Unit for Panel Processing Pre-milling unit Automatically timed engagement Motor power: 2.2 kW Edge Gluing Edge roller magazine Glue reservoir for EVA hot melt adhesive Pre-melter for EVA hot melt adhesive Hot air system: AIRTEK Number of pressure rollers: 4 NC-controlled Edge Processing Units Number of edge processing units: 7 End-capping unit Number of motors: 2 Motor power: 0.35 kW Fine milling unit for flush trimming and rounding Number of motors: 2 NC-controlled Motor power: 0.55 kW Corner rounding unit Manufacturer model: WD60 Motor power: 0.35 kW Rough milling unit Motor power: 3.5 kW Edge trimming unit NC-controlled Glue application unit Polishing unit Number of motors: 2 Motor power: 0.18 kW MACHINE DETAILS Control and Safety Machine programming software: PowerControl PC20 Safety standard: CE marking Electrical Data Total connected load: 22 kW EQUIPMENT Pre-milling unit Edge roller magazine Glue reservoir for EVA hot melt adhesive Pre-melter for EVA hot melt adhesive Ibsdpfx Alozmtivo Soa Hot air system AIRTEK 4 pressure rollers End-capping unit Fine milling unit for flush trimming and rounding Corner rounding unit WD60 Rough milling unit Edge trimming unit Glue application unit Polishing unit Spray unit Machine programming software PowerControl PC20

Condition: used, Year of construction: 2015, edge thickness (max.): 22 mm, feed rate X-axis: 25 m/min, milling spindle speed (max.): 12,000 rpm, Equipment: CE marking, The machine has the following configuration: Pre-milling unit Manufacturer/Model: RT-E Motor power: 4 kW Gluing Preheating lamps: for heating the panel side Iedpezmvpxofx Al Soba PUR pre-melter: Nordson PURBLUE 4-HO Glue application unit: 100 V End-capping unit Manufacturer/Model: YU/SP750 Number of motors: 2 Positioning: NC-controlled Milling unit Manufacturer/Model: Type U Motor power: 4 kW Speed: 12,000 rpm Engagement: automatically time-controlled Polishing unit Number of motors: 2 TECHNICAL DETAILS Min. panel height: 10 mm Max. panel height: 62 mm Min. panel length: 380 mm Min. panel width: 55 mm Min. edge thickness: 0.4 mm Max. edge thickness: 22 mm Max. feed rate: 25 m/min Pressure: rubber belt MACHINE DETAILS Control system: PC control EQUIPMENT CE marking Rubber belt pressure Panel support guides Pre-milling unit RT-E Preheating lamps for panel side PUR pre-melter Nordson PURBLUE 4-HO End-capping unit YU/SP750 Milling unit Type U Polishing unit The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents with a descriptive character. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 6527

Condition: ready for operation (used), Year of construction: 2016, functionality: fully functional, workpiece height (max.): 60 mm, roll diameter: 830 mm, The dismantling is scheduled for calendar week 35. Until then, the buyer can inspect the system while it is in operation in Lithuania. Fully automatic edge banding line with the following machines: HOMAG PROFI KAL330/9/A3/WZ (year of manufacture 2013) HOMAG PROFI KAL370/8/A3/WZ (year of manufacture 2016) HOMAG PROFI TBL100/20/30/F infeed table (year of manufacture 2013) HOMAG POWER TWL410/25/LQ transfer system cross conveyor (year of manufacture 2016) TECHNICAL DETAILS Edge banding machines HOMAG PROFI KAL330/9/A3/WZ & PROFI KAL370/8/A3/WZ Workpiece width without edge, with workpiece thickness of 12–22 mm: min. 60 mm (depending on workpiece length) Workpiece width without edge, with workpiece thickness of 23–60 mm: min. 100 mm (depending on workpiece length) Workpiece overhang: 30 mm Workpiece thickness: 12–60 mm Edge height: max. workpiece thickness + 4 mm Edge material on roll: 0.3–3 mm Edge material height PVC: max. 135 mm Edge material height veneer: max. 100 mm Roll diameter: max. 830 mm HOMAG PROFI TBL100/20/30/F infeed table Roller diameter: 54 mm Roller spacing: approx. 60 mm Panel length: 240–2,500 mm Panel width: 120–3,000 mm HOMAG POWER TWL410/25/LQ transfer system cross conveyor Roller diameter: 64 mm Roller spacing: 110 mm Ibodpjztazfsfx Al Sja Panel length: 240–2,500 mm Panel width: min. 240 mm Panel thickness: 8–60 mm Panel weight: max. 80 kg EQUIPMENT Gap-free joining-cutting unit on both edge banding machines A3 basic gluing unit on both edge banding machines Gap-free processing units on both edge banding machines FA11 finishing unit on the HOMAG PROFI KAL330 FA21 finishing unit on the HOMAG PROFI KAL370 Fixed stop on the left side of the infeed table Transport rollers on the infeed table Lateral conveyor belt on the infeed table Electropneumatically controlled transverse safety device on the infeed table Manually adjustable infeed safety device Set for small parts Integrated air cushion table Fixed stop on the left side at the infeed and outfeed of the transfer system cross conveyor Infeed roller track with conveyor belt and cross conveying Controlled cross conveyor at the infeed Outfeed roller track Controlled cross conveyor at the outfeed Electropneumatically controlled stop protection device Lateral transport belt Manually adjustable panel overhang

Condition: ready for operation (used), Year of construction: 2018, machine/vehicle number: 974/1-810, functionality: fully functional, operating hours: 1,483 h, workpiece height (max.): 60 mm, feed rate X-axis: 18 m/min, controller model: Edge Control 19 mit 18,5" Touchscreen, The machine was last serviced in February 2026 and will continue to operate until August 5, 2026. The machine has the following configuration: Edge milling unit 1802 Motor power: 2 x 2.0 kW 1st milling cutter: Diamond Ø 70 x 64 x 30 mm, Z2+2, left-hand rotation for edge milling unit 2nd milling cutter: Diamond Ø 70 x 64 x 30 mm, Z2+2, right-hand rotation for edge milling unit Edge feeder 1901 SYNCHRO (fully automatic) Glue application station Glu Jet GJ301 (automatic) Power: 2.3 kW, 50 Hz Ibedozrf Nrspfx Al Ssa Cartridges: Reservoir for 14 cartridges (1.4 kg) GluJet collection container Printing unit 1913 MOT Cutting unit 1918 (60 mm) pneumatic Multi-function milling unit 1826 MOT4 Motor power: 2 x 0.65 kW Air Stream System milling cutter: Diamond Ø 58 mm x 24 mm, Ø 20 mm Z = 2 R = 2 mm, left-hand rotation Air Stream System milling cutter: Diamond Ø 58 mm x 24 mm, Ø 20 mm Z = 2 R = 2 mm, right-hand rotation Profile milling unit 1833 MOT4 1st milling cutter: Diamond Ø 72.5 mm x 19 mm, Ø 20 mm Z = 4 Radius R = 2 mm, left-hand rotation with CM technology 2nd milling cutter: Diamond Ø 72.5 mm x 19 mm, Ø 20 mm Z = 4 Radius R = 2 mm, right-hand rotation with CM technology Scraping blade unit 1929 MOT4 Tungsten carbide reversible inserts for scraping blade holder R = 2 mm (2 pieces required) Surface scraping blade FK 701 Smoothing unit 1940 (2 x 0.12 kW, 50 Hz, 1400 rpm) Spray device 1856 TECHNICAL DETAILS Feed speed: 10 - 18 m/min Workpiece length min: 160 mm Workpiece width min: 60 mm Workpiece thickness: 8 - 60 mm Edge height max.: 65 mm Edge thickness roll material: 0.4 - 3 mm Edge thickness strip material max.: 8 mm MACHINE DETAILS Control: Edge Control 19 with 18.5" touchscreen Infeed guide rail length: 1,350 mm Electrical system for stepless feed: 400 V / 50 Hz Feed electric motor: 2.2 kW Operating hours: 1,483 h EQUIPMENT Motorized pressure bridge adjustment Nesting - tactile probe vertical, top & bottom Edition 18 package ECO MODE energy-saving mode ITronic system

Condition: used, machine/vehicle number: 008662, Position 1: Single Edgebanders IMA-NOVIMAT CONTOUR I/G80/790/R3 Ibodpfx Aezmmtnel Soa Position 2: Panel Return Systems IMA-NOVIMAT CONTOUR I/G80/790/R3

Condition: new, Year of construction: 2026, 0,4-8 mm Workingpiece thickness from to 8-60 mm Isdpfxezu A R Ss Al Sjba Total length 4930 mm Feed speed 10 m/min. Weight 1500 kg

Condition: used, Year of construction: 2010, Edge milling machine Manufacturer: Brandt Ibedpfx Ajzuzlhsl Sea Type: FTK 130 Year of manufacture: 2010 Note: The technical data and descriptions are a transcript of the original order confirmation. The data is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2010, Edge banding machine Manufacturer: Brandt Type: Optimat KTD 720 Year of manufacture: 2010 Note: Ijdpfjzuzlbex Al Ssba The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Factory-reconditioned edge processing line for 3 mm edges Manufacturer: IMA Type: Combima Consisting of: Machine 1: Used edge processing machine from IMA, type COMBIMA Factory-reconditioned with a 12-month warranty - Working width max. 1,500 mm, edge thickness approx. 0.3 - 3 mm Ibjdpjzuyqvefx Al Soa - Rolling needle bearing chain, drive with 3 kW motor, steplessly adjustable from 9 - 45 m/min - Motorized width adjustment with electronic setpoint and actual value display - Double trimming unit with 2 motors, 4.4 kW, 100 Hz - Milling unit with 1 motor, 4.4 kW, 100 Hz - Hot melt adhesive unit with 2-roller magazine and automatic Quickmelt hot melt adhesive feed - Trimming unit with 2 motors, 0.4 kW - Pre-milling and flush milling unit with 2 motors, 1.5 kW - Chamfering unit with 2 motors, 0.6 kW - Profile drawing blade unit - Straight drawing blade unit - Edge sanding/buffing unit - Beckhoff control system with screen - Electronic converter 100 Hz, manufacturer: KEB - Electronic converter 200 Hz, manufacturer: KEB - 1 used rotating device for changing from longitudinal to transverse - Factory-reconditioned with a 12-month warranty - Max. panel length 2,500 mm, max. panel width 1,500 mm Machine 2: Used edge processing machine, manufacturer: IMA, type COMBIMA Factory-reconditioned with a 12-month warranty - Working width max. 3,000 mm, edge thickness approx. 0.3 - 3 mm - Rolling needle bearing chain, drive with 3 kW motor, steplessly adjustable from 9 - 45 m/min - Motorized width adjustment with electronic setpoint and actual value display - Protective milling unit with motor 3.3 kW, 100 Hz - Double trimming unit with 2 motors, 4.4 kW, 100 Hz - Enclosed gluing unit with double roller magazine and automatic Quickmelt hot melt adhesive feed - Trimming unit with 2 motors, 0.4 kW - Pre-milling and flush milling unit with 1 upper and 1 lower motor, 0.4 kW - Chamfering unit with 2 motors, 0.4 kW - Copy milling unit with 2 motors, 150 W - For milling off strip overhangs on front and rear lower workpiece profiles, copy milling unit with 2 motors, 150 W - For milling off strip overhangs on front and rear upper workpiece profiles, profile drawing blade unit - Straight drawing blade - Buffing unit - Center support - Pull-out rollers 800 mm - Beckhoff control system with screen - Electronic converter 100 Hz, manufacturer: KEB - Electronic converter 200 Hz, manufacturer: KEB Delivery time after order placement approx. 4-6 months (depending on current workload and scope of desired work). Individual machine configurations are possible according to customer requirements, as the machines are disassembled down to the base frames and reassembled after replacing all wear parts.

Condition: used, Year of construction: 2010, - Release agent application, top and bottom - Scoring saw with 2.2 kW motor - Trimming unit with 8.0 kW motor - Double milling unit with 2 motors, each 4.5 kW - Gluing unit - End trimming unit - Flush trimming unit - Multi-function unit - Multi-profile edge trimming unit - Spray nozzles, top and bottom - Flat edge trimming unit - Buffing unit - Grooving unit Double-sided edge banding machine Manufacturer: IMA Type: Combima/II/390/B/L12 Year of manufacture: 2010 For longitudinal and transverse feed Ibedjzuyqijpfx Al Sja - 2 low-maintenance precision roller chains with 75 mm wide and 85 mm long, rubber-coated chain plates, with cams - Spacing 1080 mm. Pneumatically adjustable to heights of 8, 16 or 24 mm. ICOS OPEN control system - Max. feed width 3,300 mm - Program-controlled master + slave width adjustment - Fixed stop on the left in feed direction Workpiece dimensions - Min. feed width 244 mm (for longitudinal processing) - Max. workpiece width (chain extension) 1,300 mm - Min. workpiece thickness 8 mm - Max. workpiece thickness 45 mm (with copying function) / 60 mm (without copying) Edge material: - Min. height 14 mm, max. height 65 mm - Roll material min. thickness 0.3 mm, max. thickness 3 mm Strips and edgebanding: - Min. thickness 0.8 mm, max. thickness 12 mm Feed speed - 10 - 50 m/min. with frequency-controlled drive. Infeed device - with 5 top-mounted, inclined and driven rollers. Center support with roller track - automatically lowerable and automatically centering. Equipped on each side with: Release agent application, top and bottom Scoring saw with 2.2 kW motor, 100 Hz, 6,000 RPM, pneumatically controlled. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Trimming unit with 8.0 kW motor, 100 Hz, 6,000 RPM. - Electronic positioning for stepless horizontal adjustment. Double milling unit with 2 motors, each 4.5 kW, 150 Hz, 9,000 RPM. - Electronic positioning for stepless horizontal adjustment. - Vertical adjustment manually with mechanical display. Gluing unit for hot melt adhesive - With single roll/edgebanding magazine for roll material up to 3 mm and edgebanding up to 12 mm - 2-fold roll magazine for roll materials up to 3 mm (can be attached to the single roll magazine) - Horizontal roll holder End trimming unit - Mounted on the upper pressure beam, with 2 motors, each 660 W, 200 Hz - Pneumatic swivel 0 + 25 for straight and miter cuts. - Automatic adjustment for miter cuts with two different edge thicknesses (e.g. 0.4 and 1.2 mm) and for "edge overhang" for copying with edge thickness 1.0 - 3.0 mm. Automatic adjustment to the feed speed 20+30 m/min. Flush trimming unit 08.0555 - With 2 motors 1,850 W, 200 Hz, 12,000 RPM. Multi-function unit 08.353 - NC controlled with 2 motors, with automatic tooling for 4 profiles. Multi-profile edge trimming unit - with automatic tooling for 4 profiles via fixed-point control Spray nozzles, top and bottom - for applying cleaning agents Flat edge trimming unit Buffing unit - With 2 motors, each 180 W, 50 Hz, 1400 RPM. 1 Grooving unit - With 4.5 kW motor, 150 Hz, 9,000 RPM. - Horizontal and vertical adjustment manually with mechanical digital display - Pneumatic activation control - Manual swivel 90 ICOS open - PC-based control system with integrated PLC and electronic path control. - User-friendly interface with Windows standards - Simple, component-oriented

Condition: used, Year of construction: 2008, - with workpiece return - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Feed rate max: 20 m/min - with groove milling unit One: Edge banding machine with return Manufacturer: Brandt Type: KDF 991 Year of manufacture: 2008 Workpiece return Manufacturer: Ligmatech Type: ZHR 05 Boomerang Year of manufacture: 2007 Technical data - Right-hand machine - Machine length: 8,260 mm - Ligmatech ZHR 05 length: 10,460 mm - Edge thickness max: 20 mm - Board thickness: 8-60 mm - Thickness of wound edge max: 3 mm - Workpiece width min: 60 mm - Feed rate max: 20 m/min - Stepless feed: material pressure zone adjustable via servomotor - Electromotive height adjustment - Infeed stop: adjustable via servomotor - Infeed stop for thin elements - Glue system for granules: glue pot above the feed chain - BRANDT glue system QUICKMELT QA 45 - Suitable for PUR adhesives - Magazine for single strips - Spray device, front, cleaning at the rear - Pre-milling unit - Preheating zone - End trimmers: 2 motors, pneumatically adjustable - Flush trimming: top + bottom, manually adjustable - Fine milling trimming unit: 2 motors, adjustable via servomotor R2 - Edge rounding unit: 4 motors, manually adjustable - Groove milling unit: manually adjustable with tilting function - Radius trimming blades: R2, pneumatically adjustable / Second set for R1 included Ibodpfxszuyp Se Al Soa - Flat trimming unit - Glue joint trimming blade - Cleaning fluid spray at the rear - Buffing unit - Solid wood edge sanding unit - Conformity marking: Including complete documentation and CE

Condition: used, Year of construction: 2010, - Application of release agent, top/bottom - Joint milling unit - Gluing unit - Trimming unit - Copy milling unit SKF-L - Profile trimming blade unit - Spray cleaning agent - Self-adjusting trimming blade unit - Buffing unit Single-sided edge banding machine Manufacturer: IMA Type: Advantage 310 Year of construction: 2010 Technical data Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65* / 150 mm *at a max. workpiece thickness of 25 mm - Workpiece thickness: min. 8 mm, 12 mm with profile trimming blades max. 40 mm (with MFA 08.346), 60 mm (with SKF) - Smallest workpiece: 65 x 300 / 150 x 150 x 19 mm - Machining allowance per workpiece edge: 0 - 5 mm (observe max. chip cross-section) - Workpiece shape: right-angled - Material: chipboard, MDF - Surface material: direct coating (melamine resin paper), paper, film, veneer Edge material - Roll material without film: Paper edges & plastic edges: 0.3 - 3.0 mm Veneer edges: 0.5 - 3.0 mm - max. edge cross-section: 150 - 180 mm² - Cut edge strips: Strips: 3.0 - 8.0 mm - max. strip cross-section: 520 mm² - Edge height: min. 12 mm, max. 65 mm - max. upper edge overhang: 2 mm - Edge profiles Paper edge: approx. 0.4 mm, chamfer 15 Plastic edge up to 3.0 mm, radius depending on the tool Strip up to 8 mm flush milling (with interchangeable motor on MFA) Machine - Constant workpiece projection from the chain track: 35 mm + edge thickness - max. trimming cross-section 520 mm² - Throughput width: min. 65 mm (with projection of 35 mm) - min. workpiece length in feed direction: 150 mm - Overall height (top edge of chain track): 940 mm - Unit side: on the left in feed direction - Pneumatic connection: approx. 7 - 8 bar Application of release agent, top/bottom Joint milling unit 08.379 and blowing nozzle - with 2 motors, each 4 kW, 9000 RPM, 150 Hz Ibedpfx Aezuyp Eel Soa Gluing unit 283.1513 with oil bath gearbox - Adhesive output 0.8 l, 60 mm high, with quick-lock system - can be used for hot melt adhesive or PU adhesive - with single roll / strip magazine, roll diameter 800 mm - with 3 main pressure rollers and 3 counter pressure rollers Trimming unit 08.415 - pneumatically swiveling to 0 or 8 degrees - with 2 motors 660 kW, 400 V, 200 Hz, 12000 RPM - 2 HM trimming saw blades 160 x 3.5 x 22, Z=36 Copy milling unit SKF-L - with 2 motors 180 W, 400 V, 200 Hz, 12000 RPM - and 2 motors 400 W, 400 V, 200 Hz, 12000 RPM - 1 set of DP profile milling cutter I 80x12xHSK25-R, Z = 4, with HSK25 shank - Profile length in the feed direction: max. approx. 50 mm - Workpiece thickness: max. 60 mm - Working speed: max. approx. 20 m/min - Distance between 2 workpieces: min. approx. 400 mm - min. workpiece projection = 35 mm + profile depth Profile trimming blade unit 08.519 - For finishing a top and bottom milled quarter-circle profile Spray cleaning agent Self-adjusting trimming blade unit 08.521 - for removing hot melt adhesive residue from the edge area of the top and bottom of the workpiece Buffing unit 08.617-2 - with an upper and lower motor: 180 W, 50 Hz, 1400 RPM - 2 polishing pads 50 x 160 x 19 mm

Condition: used, Year of construction: 1996, - Double-sided IMA COMBIMA for longitudinal machining - Swiveling device - Double-sided IMA COMBIMA for transverse machining 1 used edge processing line IMA COMBIMA / K/ II/ R75 / 1075 / V / R3 Year of manufacture: 1996 Consisting of: - Double-sided IMA COMBIMA for longitudinal machining: Ibsdpfx Aljzuypxj Soa Double edging unit 2 x milling units Gluing unit with granular pre-melting device 6-position roller magazine for edge material 1 x main pressure roller and 4 x follow-up pressure rollers Cutting unit Flush trimming 2 x fine milling units Profile trimming blade Surface trimming blade Buffing unit Smoothing unit - Swiveling device from longitudinal to transverse - Double-sided IMA COMBIMA for transverse machining Protective milling Double edging Grooving milling unit Gluing unit with granular pre-melting device 6-position roller magazine for edge material 1 x main pressure roller and 4 x follow-up pressure rollers Capping at the top pressure (retrofit to current model) Flush trimming Fine milling 2 x MFA milling units Grooving milling unit Profile trimming blade Surface trimming blade Copy buffing (4 motors) Buffing (2 motors) Smoothing unit Note: The technical data and descriptions are a transcript of the order confirmation at the time. Data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm Ijdpfozuyprox Al Sjba - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm Single-sided edge banding machine Manufacturer: IMA Type: Novimat Contour/I/G80/790/L20 Year of manufacture: 2009 Technical data - Electronically controlled feed speed: 6-30 m/min - Edge material thickness: 0.3 - 3.0 mm - Paper, PVC, and ABS edge bands: 0.3 - 3.0 mm - Veneer: 0.5 mm - 3.0 mm - Wood strips: 0.8 - 20 mm - Edge height: 14 mm - 65 mm - Maximum edge overhang from above: up to 8 mm edge thickness - 5 mm, over 8 mm - 2 mm Workpiece size: - Minimum workpiece length in the feed direction: 150 mm - Minimum workpiece width: 25 mm, thickness: 65 mm - Minimum workpiece thickness: 8 mm (without profile trimming blades) or 12 mm with profile trimming blades - Maximum workpiece thickness: without corner copying, max. 60 mm (max. 40 mm with corner copying) - Smallest element: 150 mm x 150 mm or 65 mm x 300 mm Note: *65 mm with a maximum piece thickness of 25 mm The edge banding machine is equipped with: - Hand-adjustable guide rail for inserting workpieces - Trimming units 08.376, 2 motors, each with 4.5 kW, spindle speed 9000 rpm, 150 Hz - Heating unit for warming the workpieces - Gluing unit with drive 283.1513, featuring a tightly sealed oil pan, drive arranged with glue pot content of 0.8 l and glue application height of 60 mm, with a pneumatic quick-clamping system for hot melt and PU adhesives, magazine for edge banding rollers and strips, edge banding roller diameter 800 mm - Glue pellet preheating unit with automatic feeding of glue pellets from a 30 kg container. - Automatic preheating unit for PU cartridges with a weight of approx. 2.5 kg and a capacity of 8-10 kg/h - Trimming unit 08.42/30/B, pneumatic adjustment of the saw blades from 0 - 25°, 2 motors 660 W, 200 Hz with frequency inverter and braking function - Pre-milling unit 08.055, swiveling up to max. 30° - Multi-chamfering unit 08.342, 2 motors, 660 W, 400 V, 200 Hz, 12000 1/min - Cleaning agent dispenser - Profile trimming blades 08.519 - Surface trimming blade 08.521 for removing excess glue from glue joints - Buffing unit 08.617-2, 2 motors with 180 kW, 50 Hz, 1400 rpm - Groove/milling unit with one motor Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2005, - Automatic infeed table - KFA unit - Return system Used single-sided edge banding machine Manufacturer: IMA Type: Combima Systems / I/R751220/R3 1 single-sided combination machine for trimming, edge gluing and edge finishing of panel-shaped workpieces made of wood and/or wood-based materials. - Automatic infeed table - KFA unit - Return system Technical data "Workpiece": Workpiece length - min.: 238 mm - max.: 2350 mm Isdpfx Ajzuyplol Ssba Workpiece width - min.: 142 mm - max.: 800 mm Workpiece thickness: - min.: 8 - 40 mm Technical data "Strip" (only for longitudinal processing): Roll material: - Paper edge bands & plastic edge bands: 0.3 - 3.0 mm - Veneer edge bands: 0.5 - 3.0 mm Edge height: - min.: 14 mm - max.: 45 mm Technical data "Machine": Variable workpiece overhang from the chain conveyor (including edge with edge thickness 0.3-3 mm): - min.: 40 mm - max.: 80 mm - PC control ICOS open - Feed speed v=5-25 m/min, frequency-controlled drive - Inclined roller table as infeed section NC infeed system for front and carcass parts - for length and width-independent automatic workpiece feed in single-sided edge processing machines. Only for the production of strip material in the 2nd pass - An additional stop rail, adjustable via NC axis. Double milling unit 08.376: - Controllable - Motor 1 operating in the same direction and motor 2 operating in the opposite direction - Reserve space on the unit carrier for a double trimming unit with electrical pre-installation for 2 x 6.6 kW. - Heater 300 lg, 2x1.5 kW, for preheating the workpiece edge. - Gluing unit 04.1570 system for straight edges and adhesive application to the workpiece. The edge thickness depends on the magazine used and is max. 3 mm. - Adhesive application for workpiece thickness max. 50 mm - 2 pre-melting tanks for PU adhesive - 12-position edge magazine for roll material 0.3-3 mm thick. (8 slots up to 3 mm, 4 slots up to 1.3 mm) Vertical roll holder for 12 rolls: - max. roll diameter 850 mm - max. edge height 45 mm - Trimming unit 08.42, for 2 motors mounted on the upper pressure bar - Pre-milling and milling unit with height sensor - with 1 motor 1000 W - Multi-profile / chamfer unit, with 2 motors 1000 W - Contour milling unit KFA 30 - Multi-profile drawing blade unit - Flat drawing blade 08.517 - Copy edging unit 08.604 - Edging unit 08.617-2 - Double milling stand 75.184, 1050 mm high, both stand sides can be used - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 6000 rpm - Milling / profile milling / grooving unit 75.34 with 1 motor, without tool, 100 Hz, 600 rpm - Motor spindle for the use of the Hydro-Format tool system - Return system, manufacturer Meinert Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: SCM Type: Olimpic K360 T-ER1 Year of manufacture: 2017 Technical data - Feed speed: 11 m/min - Edge thickness: 0.4 - 6 mm - Control: SCM control panel with display - Board thickness: 8 - 60 mm - Power supply: 400 V / 3~ / 50 Hz, 23 A - Min. workpiece: 140 x 90 mm Units Pre-milling - 2 counter-rotating diamond heads (up to 3 mm removal) EVA gluing unit Pressure zone with driven roller + 2 pressure rollers End trimming unit K-2 (straight / beveled, automatic switching) Flush trimming - flush, radius, chamfer Corner rounding R1/R2 Profile + surface scraper blade Ibedpfx Alozuyk No Sea Polishing unit Anti-adhesive liquid system (2 liquids), edge roller feed Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2023, Edge banding machine Manufacturer: Biesse Type: Akron 1440 A Year of manufacture: 2023 Technical data - Panel height*: 10-60 mm - Edge height: 14-64 mm - Edge thickness from roll: 0.4-3 mm - Edge thickness in strip form: 0.4-12 mm - Panel overhang over the chain: 25 mm - Panel length: 140-3200 mm - Minimum panel width (at a length of 140 mm): 85 mm - Minimum panel width (at a length of 250 mm): 50 mm - Chain feed speed: 12 m/min - Distance between panels: 450-650 mm - NC axis package for automatic machine setup - Mounting kit for workpiece return * Minimum panel height: 8 mm at a maximum edge thickness of 1.5 mm. Depending on the selected processing units. Maximum permissible feed speed: 12 m/min. Units Anti-stick spray unit ADZ02 Pre-milling unit RT02 - two high-frequency motors, each 1.8 kW, 12000 RPM Gluing unit VC-511 - Processing of EVA and PUR granular adhesive - Filling volume: 1.5 kg Pressure zone Iedszuyk Aepfx Al Sjba - 1 driven pressure roller 100 mm, with independently adjustable pressing pressure - 2 and 3 pressure rollers, not driven, 60 mm, with anti-stick coating, arranged conically in relation to each other and pneumatically adjustable Trimming unit IT-70-S - two high-frequency motors, each 0.8 kW, 12000 RPM - The trimming can be performed straight (0°) or at an angle in a range of 0 to 15°. - Anti-static/coolant spray device after the trimming unit Flush trimming unit RF02 - two high-frequency motors, each 0.65 kW, 12000 RPM Corner rounding unit - two high-frequency motors, each 0.65 kW, 12000 RPM - Corner rounding is possible for both workpieces with a straight edge profile and for postforming and softforming profiles at 90° and 180° corners. Edge scraping blade RB02 - Switching between two processing profiles is done manually. Glue line scraping blade RC02 Polishing unit SZ02 - two motors, each 0.37 kW, 2800 RPM Hot air blower PH-501 - Power: 2 kW - Infinitely adjustable temperature control Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2003, Single-sided edge trimming and gluing machine Manufacturer: IMA Type: AVM/K/I/G80/822/S3R3L20 Year of manufacture: 2003 For milling, edge gluing, and finishing for a standard groove - only for pre-shaped/pre-grooved doors and square-edged doors Left-hand machine (fixed stop on the left). Complete processing in 3 passes 1st pass: Processing of the top surface of the door (transverse processing) 2nd pass: Door long edge 3rd pass: Door long edge During the 2nd and 3rd passes, the protruding transverse edge from the 1st pass is milled off by using a co-rotating/counter-rotating milling process. Double groove gluing is only possible through modifications to the machine and subsequent manual finishing of the edge. Max. door thickness: - Straight edge: approx. 70 mm - Groove gluing: approx. 60 mm Stable machine frame as a support for aggregates and housing for electrical installation. Drive for feed speeds of approx. 5-25 m/min., mechanically infinitely adjustable. (not to be confused with processing speed) Continuous, plastic-coated strip-type conveyor chain, approx. 80 mm wide, with automatic central lubrication. Manually height-adjustable top pressure with a V-belt 80 mm wide and spring-loaded, ball-bearing guide rollers. Machine length approx. 10,900 mm Ijdezuykvopfx Al Seba Infeed table at the machine inlet. 1 horizontal, manually adjustable, unheated stop bar 1 joiner milling unit controllable, not swiveling, without sensing with 2 motors, each 3 kW Gluing unit for optional operation of straight edge or softforming gluing, by changing the glue application. Edge material: - Strips: up to 1.3 mm - Roll material: 0.4-3 mm - Solid wood strips: 6 mm Strip length max.: 2550 mm Strip height: 14-80 mm (depending on glue application) with: - Side adjustment by hand for the pneumatically controlled glue application. - Height adjustment by hand -15mm downwards and up to +10mm upwards. 1 bell for the main pressure roller, manually adjustable 1 glue application 0.8L, max. edge height 70mm, straight edge with pneumatic quick-release, Chem-Coat coated, electronic temperature control 1 hot melt glue application 0.8L with quick-release, up to max. 80 mm high edge material, soft edge, Chem-Coat coated, with temperature control and control unit for the strip coating 1 automatic Quickmelt hot melt glue feeder with a heating power of 5.0 kW 1 2-fold magazine only for edge material up to 3.0 mm thick, can be manually attached to the single-roll magazine 1 groove forming pressing unit for pressing the edge material into the groove with: - an activation unit 15 kW for re-activating the edge material for groove forming - a pneumatically controlled forming shoe for the underlapping edge - a pneumatically controlled forming shoe for the entire groove - additional post-pressing rollers for the edge areas in the groove - an electro-pneumatic lateral retraction device for the entire pressing unit 1 horizontal adjustment with mechanical digital display 1 trimming unit for 2 motors mounted on the top pressure for trimming the front and rear edge/strip overhang, for trimming cuts flush or with a bevel. 1 milling unit for 2 motors with height sensing, side sensing, for pre-milling from below and above with 2 motors 1kW, 400V, 200Hz, 12,000 RPM, 30° swiveling 1 milling unit for 2 motors with height sensing, side sensing, for fine milling from below and above with 2 motors 660W, 400V, 200Hz, 12,000 RPM, 30° swiveling Note: The technical data and descriptions are copies of the original order

Condition: used, Year of construction: 2019, Edge banding machine Manufacturer: SCM Type: Minimax E10 Year of manufacture: 2019 Technical data Edge thickness (strip material): 0.4 - 3.0 mm Edge thickness with shear cutter at 80 mm edge height: 0.4 - 1.5 mm Edge thickness with shear cutter at 50 mm edge height: 0.4 - 2.5 mm Edge thickness with shear cutter at 45 mm edge height: 0.4 - 3.0 mm Edge height: 10 - 84 mm Workpiece thickness: 8 - 80 mm Minimum workpiece width: 50 mm Minimum edge length: 210 mm Minimum inner radius (concave) at 0.4 mm edge: 25 mm Minimum outer radius (convex) at 0.4 mm edge: 5 mm Feed speed: 4 / 8 m/min Processing temperature: 140 - 220 °C Edge feed Integrated shear cutter for cutting edge material from the roll. Roll table for holding roll material. Suitable for ABS edges, melamine edges, veneer edges, and other pre-fabricated edge strips. Gluing system Teflon-coated glue tank below the table top. Continuous glue circulation to prevent glue deposits. Fast heating time of approx. 7 minutes. Standby function with timer. Ibedpfx Aljzuykpo Sja Glue tank capacity: 1.5 liters. Pressure system Motor-driven glue application roller. One free-running pressure roller. Foot pedal for start and stop control of the working cycle. Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Edge banding machine Manufacturer: Homag Type: Optimat KDF 440 C Year of manufacture: 2017 Technical data Workpiece thickness: 8 - 60 mm Edge material: 0.4 - 8 mm (depending on the equipment) Feed rate: 8 - 18 m/min (stepless) Workpiece length min. approx. 120 mm Workpiece width min. approx. 60 mm Glue application EVA hot melt adhesive, optionally PUR-compatible Glue reservoir Teflon-coated, quick-change system possible Total connected load approx. 15 - 20 kW (depending on the equipment) Compressed air requirement: 6 - 7 bar Machine weight: approx. 3,000 - 3,800 kg Control system: powerControl / powerTouch CE marking Equipment: Joint milling Glue application Pressure zone Cut-off saw unit Milling unit top/bottom Ibedpfx Alezuykco Sea Corner rounding unit Scraping blade unit Edge finishing unit Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2012, Softforming edge banding machine with panel cutting device Manufacturer: Elwood Year of manufacture: 2012 Technical data: - Adhesive application system with slotted nozzle - Compatible with EVA and PUR adhesives - Meler adhesive melting and application system - Electronically controlled adhesive temperature and melting time - Panel thickness: 10-60 mm - 2 profiling milling units - IR heating lamps for material preheating - Spray device for release agent - Pressing zone with heated tower pads (can be replaced with pressing rollers) - Edge band magazine Ijdpszuyi Ssfx Al Seba - Front and rear trimming units - Top and bottom flush trimming units for longitudinal edge overhang (2 at the top + 2 at the bottom) - Top and bottom polishing units - Computer control for quick, easy and precise adjustment of the machine's main functions and units Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2009, Edge banding machine Manufacturer: IMA Type: Novimat/I/G80/650/R3 Year of manufacture: 2009 Technical data - Workpiece overhang from the chain conveyor: 38 mm - Feed width: min. 65 mm (with max. workpiece thickness of 25 mm) - Workpiece length in feed direction: 150 mm - Overall height (top edge of chain conveyor): 960 mm - Feed speed: approx. 6 - 30 m/min, electrically adjustable - Machine control system ICOS open compact Workpiece - Workpiece length: min. 150 mm - Workpiece width: min. 65 mm - Workpiece thickness: 8 - 40 mm (with edge trimming function) / 60 mm (without edge trimming function) - Smallest workpiece: 150 x 150 mm or 65 x 300 mm - Edge material: paper, plastic and veneer - Height: 14 - 65 mm - Roller material thickness: 0.3 - 3.0 mm (veneer edges limited to max. 1.0 mm) - Max. upper edge overhang: 5 mm Units Infeed area - Release agent applicator mounted at the top and bottom, not adjustable Edge trimming - 2 motors 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function Isdpfszuyi Esx Al Sjba - Motor 1 counter-rotating - Motor 2 co-rotating Gluing unit VTG 3-6 - with one preheating nozzle 300 mm for preheating the workpiece edge - 6-position edge magazine for roller material 0.3 - 3 mm thick. - 1 driven main pressure roller and 4 pressure rollers, with scraper, pneumatically adjustable Glue application - with pneumatic quick-lock system - Chem-Coat coating - electronic temperature control - Volume 0.8 l Pre-melting tank approx. 1 l - Heating power 3 x 400 W - with EVA glue, approx. 7.0 kg/h - with filler-free glue, approx. 5.0 kg/h Cutting unit - 2 motors 660 W, 200 Hz - incl. frequency inverter with braking function - pneumatic pivoting 0+25 for straight and bevel cutting Flush trimming - 2 motors each 1000 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function Multi-profile trimming unit - 2 motors each 660 W, 400 V, 200 Hz, 12000 rpm - with HSK 25 shank - incl. frequency inverter with braking function - for trimming 4 profiles - with stepper motor axes for horizontal and vertical positioning Contour trimming unit KFA x30 - 1 motor 500 W, 400 V, 400 Hz, 18000 rpm - Program-controlled conversion for up to 4 profiles - incl. fine positioning for different edge thicknesses Multi-profile scraping blade - Stepper motor axes for horizontal and vertical positioning - Scanning from above and below (max. 4 profiles) - Scanning from the side via pneumatic pressure Spray nozzles at the top and bottom for applying cleaning agents - fixed, not adjustable Surface scraping blade - with height sensing skid - electronically controlled horizontal positioning Buffing unit - 2 lower and 2 upper motors, 180 W, 50 Hz, 1400 rpm - 1st motor pair with cloth-sisal discs 50x160x19 mm - 2nd motor pair with polishing discs 50x160x19 mm - The motors operate in the same direction and are both tilted and pivoted in the feed direction. - Each motor can be individually adjusted vertically 2x NC-controlled grooving - 2 milling motors each 4.5 kW, 150 Hz, 9000 rpm - incl. frequency inverter with braking function - one manual 90-degree pivoting device from 180 -270 with co- and counter-rotating function - Horizontal, stepless adjustment with AC servo motor for grooving unit Workpiece return Note: The technical data and descriptions are copies of the order confirmation at the time. The information is for informational purposes only and is non-binding.