FLAT GRINDING MACHINE

Ziersch & Baltrusch 8.30

Year of construction: 1994, condition: good (used), Ziersch & Baltrusch surface grinding machine - with Formmaster 6 / 30 - with belt filter unit Nljdpfx Afsk Ixl Asrsi - with coolant unit - width: 250 cm - depth: 200 cm - height: 220 cm Good condition fully functional can be viewed and tried on site. Shipping also abroad. Viewing : Basically, I would like to point out that to avoid misunderstandings, the item is welcome to be inspected and tested under power before purchase. Please ask questions before buying to avoid ambiguity. For general questions or to make an appointment for a viewing, I am, at the phone number below or above, always available. Errors in the description and subject to prior sale. VAT is shown separately on my invoices. Shipping with forwarding agent.

Condition: used, Year of construction: 1996, grinding length 600 mm Nlsdpfx Aot Tqrnofrsi grinding width 250 mm workpiece height ca. 385 mm table surface area 600 x 200 mm table speed -stepless- 2 - 35 m/min table load capacity max. 250 kg grinding wheel size ø 225 x 25 mm grinding wheel hole diameter 50,8 mm vertical feed autom. 0,001 - 0,099 mm rapid traverse vertical 600 mm/min cross feed of table continual 10 - 1000 mm/min rapid traverse cross 1000 mm/min total power requirement 6 kVA dimensions of machine L x W x H 2,65 x 1,70 x 2,28 m Accessories: DRO on Y-and Z-axis, magnetic plate 600 x 200 mm, grinding wheel with flange, wheel trueing attachment, wet grinding attachment with paper band filter

Condition: used, turning diameter max. 360 mm turning length 505 mm control Mazatrol SmoothC max. swing diameter over bed 660 mm Nedov Dxw Rjpfx Afroli swing diameter over slide guides max 255 mm bar material dia. max. 80 mm turning speed range - spindle 35 - 4000 U/min max. torque on the spindle 358 Nm x-axis 225 mm rapid traverse X-axis 30 m/min z-axis 605 mm rapid traverse Z-axis 33 m/min spindle nose A2-8'' spindle bore 91 mm spindle hollow 80 mm Milling spindle speeds ( driven tools) 5000 1/min torque on milling spindle max: 47 Nm power capacity - milling spindle 5,5 (40%ED) kW tailstock quill taper MT 5 Travel- tailstock 565 mm Axial pressure max 5,0 Nm Tool turret 1 Numbers of tools 12 (angetrieben) turning tool - shaft cross cut 25 x 25 mm tool taper BMT Required air-pressure 5 / 160 bar / l/min voltage 400 V coolant tank 180 l engine output 18,5 (30min Betrieb) kW Rated power (100% continuous operation) 15 kW weight of the machine ca. 6 t dimensions of the machine ca. 3,6 x 2 x 1,8 m Machine incl. the following special accessories: Chip conveyor on the right side Productivity package C - special according to storage machine This package includes: High-performance coolant system (1.1 kW) Flow rate max. 17.6 l/min Preparation for chip conveyor (lateral) Automatic tool eye STANDARD ACCESSORIES Transformer for the European market Use of linear systems with guide carriage SD MEMORY I/F(1P) + USB MEMORY I/F(1P) 1 x USB memory interface (1 slot) Spindle bore 91 mm Set of manuals in electronic form on CD Mazak standard colour CE marking, metric, 50 Hz C-axis input accuracy 0.0001° NC controlled tailstock Tailstock pressure adjustment Tailstock with fixed quill MK5 SAFETY DEVICES Operator door with interlock switch Double foot switch Hydraulic pressure lock Fully enclosed work area Work area lighting Safety precautions according to global standard COOLANT SUPPLY Grundfos coolant pump type MTA (0.25kW / 7.6L/min) Complete coolant system Automatic switch-off via circuit breaker triggering MESSSYSTEM Absolute positioning system NUMERICAL CONTROL Synchronous tapping with milling spindle Relocation Detector Mazatrol SmoothC 10.4’ colour screen User macro (600 variables) EIA/ISO input function Tool path check in the background Thread cutting function (G33) Polar coordinate input (EIA) Drawing data direct input function Interface for LAN Various tool holders - All dimensions, weights and performance data are non-binding - Used machine without warranty -

Condition: good (used), Year of construction: 2010, grinding length: 600 mm, grinding width: 220 mm, Manufacturer: Ziersch Type: ZT 24 Control: Mitsubishi TOUCH panel Year of construction: 2010 Sturdy, cast iron execution of all machine components High machine weight for maximum rigidity Preloaded precision linear guideways in the vertical and cross axis (Bosch Rexroth) for highest accuracy Scraped and turcite coated slideways in the longitudinal axis provide excellent vibration absorption and a high-quality grinding surface pattern. Hydraulic longitudinal motion with return cooling unit to achieve good surfaces Electro-mechanical cross and vertical motion Measuring systems in vertical axis (Heidenhain) for precise positioning Maintenance-free paper band filtration unit with up to 500 l tank and 2-bar pressure pump for effective cooling and rinsing Integrated rinsing channel Magnetic separator for prefiltration of the paper band filtration unit Infinitely variable grinding spindle motor Machine lamp Table-mounted dressing device for high precision and surface finish Electro-permanent magnetic chuck (SAV) with integrated pole changing unit and traction regulation Partial encapsulation of the machine with sliding door and a service door Effective splash guard and excellent accessibility Preparation of the machine for installation of a coolant mist exhaust unit Control system features: Very comfortable and easy to operate Z-control Automatic vertical infeed with dressing amount compensation Fully automatic grinding cycle with dressing cycles Easy operation via touchscreen Nedovt Tm Sepfx Afrsli Large and clear colour screen (10.4") Electronic handwheel, usable in vertical- and cross axis Specifications Metric US Standard X - axis 600 mm Y - axis 220 mm Z - axis 540 mm Table length 400 mm Table width 250 mm Load more specifications Dimensions ( Estimate) Length 3050 mm Width 2050 mm Height 2510 mm Weight 2900 kg Please note: The information on this page has been obtained to the best of our knowledge and belief from the manufacturer. The information is given in good faith but the accuracy cannot be guaranteed. Accordingly, they will not constitute a representation and contractual terms. We recommend that you review all important details.

Condition: good (used), Manufacturer ZIERSCH & BALTRUSCH Type FS 2560 year of construction 1987 Machine weight approx. 2000 kg x-path 600 mm y-path 250 mm Nodpfjtpc Elox Afreli z-path 500 mm Center height 500 mm Grinding wheel diameter 225 mm Grinding wheel width 25 mm

Condition: excellent (used), Year of construction: 2020, machine/vehicle number: 161.40.492, Used Strautmann bale press, type: BalePress 3, serial number: 161.40.492, year of construction: 2020, with tape extraction hook Power supply: 230 V 50 Hz Electrical Power: 0,75 kW Protection class: IP54 Pressing force: 27 kN Press stroke: 580 mm Weight of the machine: 275 kg Transport dimensions (lxwxh):1070 x 754 x 2110 mm (without pallet) 1070 x 754 x 1945 mm Filling opening (wxh): ca. 700 x 450 mm Cycle Time: 27 sec. Bale weight 30 kg Bale size in the chamber (lxwxh)*: 500 x 700 x 500 mm Bale tying: strapping with two twines, PP band ADVANTAGES Easy to install and transport Easy to handle bales Practical emptying of bales Foil/cardboard mode switch Simple and safe operation Stable door locking system Stable guide of the press plate "D" level security system. Small space required BP3: Bale tying system with open door; BP3CD: tied bales with door closed Solid construction Nledovvk T Iopfx Afrsi Wheel door lock Ideal for small shops. The Strautmann BalePress 3/3CD is a small, single-chamber baler. At the same time, it is perfectly suited for baling common and smaller quantities of paper, foil, PET bottles and plastic waste and, thanks to its compact design, it can also fit into a very small space. It is clearly the best alternative for our partners with less waste and a waste container with a small footprint. Depending on the pressed material, the 3 ton pressing force can result in a volume reduction of up to 90%. The machine can produce relatively small and therefore easy to handle bales of up to 35 kg. By using it, significant savings in storage and transportation costs can be achieved. Bales are easier to transport and sell than untreated waste. Due to its dimensions, the machine can also fit in a very small space, and because of this, the baling technology is no longer available to our partners who have limited space. Price 3.490 Euro + VAT, negotiable, FCA: Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: used, Year of construction: 1984, Technical details: grinding length: 500 mm grinding width: 250 mm workpiece height: 250 mm table surface area: 530 x 200 mm magnetic plate size: L:460 x B:150 x H:87 mm table speed: 2 - 32 m/min table adjustment: Längsweg: 550 mm table adjustment: Querweg: 300 mm feed of spindle: 0,001 mm/Hub grinding spindle speed: 3.000 U/min dimensions of grinding wheel: max. Ø 250 x B:25; Bohung Ø 76 mm Nsdju Ngkyspfx Afroli total power requirement: 4,3 kW weight of the machine ca.: 2,2 t dimension machine xH: 2,3 x 1,8 x 2,2 m dimensions of hydaulic: L: 500 x B: 480 x H: 680 mm dimension coolant device LxWxH: 0,65 x 0,45 x 0,8 m The machine is currently equipped with a grinding wheel Ø 240 x 22mm. On the table there is a permanent magnet plate with 30 induction fields, operated by a hand lever. Operation via swiveling control panel. no dressing device incl. oil collecting tank; grinding wheel holder and available documentation *

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, The BTS-MF250 is the ideal waste baler for compacting your loose cardboard and plastic film waste into a bale of up to 250 kg. With a crush insert baler is even suitable for crushing individual small and large drums and also other sheet metal containers. The baling press impresses with its ease of use, safe operation and its large filling volume. By baling these valuable and recyclable materials you achieve a volume reduction of up to 90%, a significant saving on your disposal costs and you properly return the material back into the recycling cycle. Pressing force: 15 Ton Bale weight: up to 250 kg (material depending) Bale size: 1000 H (var.) x 1200 W x 800 D mm Machine size: 2900 H x 1759 W x 1185 D mm Machine size: 985 kg Transport height: 2250 mm Loading aperture: 1200 W x 680 H mm Cycle times: 34 seconds Motor: 2.2 kW 16 Amp Power supply: 220 - 240 V (1 phase) Noise level: 68 dB User-friendly lever control Bale kicker for easy eject the bales Retainer for reducing the material spring back Reel holder for 4 rolls of strapping A quality product “Made in Europe” Nljdpfxsvalq As Afroi Suitable for compacting Cardboard Plastic film and foils Big Bags Drums and sheet metal containers Canisters and plastic containers Clothes Light valuable materials Optional extras Machine colour RAL Crush insert PLC auto compaction cycles with bale full light and E-stop with locking key Sliding top door Strapping rolls Power supply 380 - 400 V (3 phase) Waste Baler, Waste Compactor, Cardboard Baler, Film Baler, Foil Baler, Packaging Plastic Film Foil, Bailer, Baling Press, Garbage Press, Trash Compactor, Baling Compactor, Paper Press, Waste Paper Press, Cardboard Press, Cardboard Compactor, Foil Press, Paper Baling Press, Waste Baler, Residual Waste Compactor