FLAT GRINDING MACHINE

ZIERSCH & BALTRUSCH FS 2560

Condition: used, Year of construction: 2004, Technical details: x-travel: 1500 mm y-travel: 1000 mm z-travel: 1000 mm control for program: TNC 530 spindle hours: noch nicht bekannt h milling head speed: 1: 30 bis 930 und 2: 930 bis 4000 / steples U/min tool taper: horiz./vertical: SK 50 (DIN 69871/Din 69872 Form A) Nedpfx Asu Nc Risb Asdc max. torque on the spindle: 1000 Nm spindle head swivable left - right: 90 ° feed: 1 - 6000 mm/min feed power: 30 kN kN rapid traverse: 15 m/min Number of tools: 1 St. table clamping surface LxW: 1600 x 800 mm table load: 40 kN kN voltage: 400 V / 50 HZ V total power requirement: 42 kW Weight approx.: 15,2 t compressed air: 6,3 bar dimension machine xH: 3,1 x 4,7 x 2,6 m dimensions: Kühlfilter: 1,9 x 1,6 x 1,4 mm space requirements approx. LxWxH: ca. 38,5 m² m² Applications: Milling, drilling; tapping, boring. with direct coded length measuring systems the guideways of the 3 axes are on flat guideways CTS and external cooling Milling head position controlled +/-90° milling spindle nominal drive power 22 kW with integrated hydraulic power unit up to 100bar operating pressure with coolant unit with filtration, with high pressure pump 60 bar (internal cooling), nominal delivery 20 l/min. and low pressure pump 4 bar (external cooling) as well as spray gun Hinged belt chip conveyor DGS, type SSF 600 P50 Accessories: Measuring probe SK40 Reference tool SK40 Milling head SEMPUCO *

Condition: like new (used), Year of construction: 2022, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 700 mm, total height: 2,800 mm, total length: 1,350 mm, total width: 1,260 mm, workpiece weight (max.): 300 kg, table width: 450 mm, overall weight: 2,300 kg, type of input current: three-phase, table length: 888 mm, drilling depth: 500 mm, Technical equipment -4-way guide changer -32-way electrode changer -Preparation for rotary swivel axis Njdpfevppw Sex Ab Aedc -High quality of drive axes and guides -Integrated compressor cooling units for electronics and external connection option for dielectric cooling -High erosion performance thanks to MOSET generator -Fine filter for working with small pipe diameters EROSIX CONTROL -Fast probing -Simple programming for complex 5-axis machining -Extensive measuring cycles -Program transfer and storage via TCP/IP interface -High operating comfort

Year of construction: 2020, condition: as good as new (ex-display), electrode diameter 0,5 to 3mm travels 300x400x350mm ) CE-cretification verifies the best possible safty all Machines in over-floor construction Nsdpfxof Hmn As Ab Asdc Elektrode Ø 0,5-3mm Travel X-Axis 300mm Travel Y-Axis 400mm Travel Z-Axis 350mm Travel W-Axis 300mm Speed W Axis 30-60mm/min Rapid feed Z-Axis 120mm/min removal rate (max.) 300:1 Table dimension 320x440mm max.generator capacity 30A

Year of construction: 2000, condition: ready for operation (used), Working area X/Y/Z: 1200mm/1200mm/840mm, dimensions X/Y/Z: 1300mm/1300mm/2010mm, weight: 650kg, sound level: 70dB(A) without blasting, 82dB(A) with blasting at 3 bar, max compressed air: 10bar. Including an electronically infinitely variable steel turntable (diameter: 1000mm), a blasting agent drying system and a second blasting gun unit with carbide blasting nozzle. Documentation available. Ndodpfx Abetk Rwts Aoc

Condition: new, empty load weight: 15,420 kg, maximum load weight: 61,080 kg, overall weight: 76,500 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 900 mm, tire size: 235/75/r17,5, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform: Loading area in extendable design with rear bevel of approx. 500 mm x 8° 8 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 50,000 kg. Ndodpjl Sl Izsfx Ab Aec Seat posts: - JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles and tires: BPW axles and suspension, 4th + 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lock via reverse gear and manual activation Tires 235/75 R 17.5 3PMSF Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) Sockets and lighting: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Paint finish: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the bulkhead 2" kingpin One galvanized steel bulkhead approx. 400 mm high Yellow-red air couplings on the galvanized connection strip at the front 2 restraining shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights A bracket for a rotating beacon at the rear of the trailer Galvanized supports under the bevel of the loading area White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear Electro-hydraulic unit at the rear under the cargo bed A holder for the warning signs, including a socket, on the gooseneck and on the rear panel on the left and right respectively Control valves for the ramps mounted on the right-hand side of the trailer A mud flap at the rear of the trailer Manual and description on USB stick 3.5" kingpin supplied loose ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm (LxH) The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container 6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Galvanized extensions, extendable by approx. 230 mm per side Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope On the chequer plates, above the kingpin and the load floor

Condition: ready for operation (used), Year of construction: 2012, functionality: fully functional, turning diameter over cross slide: 390 mm, turning length: 550 mm, turning diameter: 350 mm, spindle bore: 90 mm, spindle speed (max.): 3,500 rpm, spindle speed (min.): 5 rpm, travel distance X-axis: 240 mm, travel distance Z-axis: 580 mm, spindle motor power: 18,500 W, total height: 1,755 mm, total length: 3,130 mm, total width: 1,643 mm, feed rate X-axis: 24 m/min, feed rate Z-axis: 30 m/min, type of input current: AC, overall weight: 4,800 kg, swing diameter over bed slide: 550 mm, chuck outer diameter: 203 mm, center width: 668 mm, center height over cross slide: 315 mm, spindle nose: A2-6, bar diameter (max.): 76 mm, controller manufacturer: Fanuc, controller model: Fanuc 21i-TB, Doosan Puma 240C (2012 Model) Heavy-Duty Boxway CNC Lathe Short Overview Available for sale is a production-ready 2012 Doosan Puma 240C CNC Lathe. This machine is a highly reliable shop workhorse featuring a solid, single-piece cast iron bed with traditional box guideways for heavy-duty cutting and superior vibration dampening. Equipped with the factory "C" Big-Bore package, this lathe pairs a large 8-inch chuck capability with a 3-inch through-hole bar capacity, making it an ideal choice for high-mix job shops and mid-sized turning applications. Ndjdpfx Aezluq Eeb Ajc Key Selling Points for Buyers Compact Footprint: Delivers heavy-duty boxway rigidity without taking up excessive floor space. Big-Bore Throughput: Handles up to 3-inch bar stock, matching the material capacities of much larger machine classes. Box Guideway Precision: Offers exceptional tool life and dampening for aggressive roughing cuts on tough alloys.

Condition: used, Year of construction: 2017, functionality: fully functional, center height: 180 mm, total width: 1,650 mm, total length: 4,900 mm, total height: 1,800 mm, overall weight: 3,900 kg, grinding length 1500 mm centre height 180 mm Nsdswm Rqgepfx Ab Asdc weight of the machine ca. 3,9 t dimensions of the machine ca. L: 4900 x 1650x 1800 m

Condition: used, Year of construction: 2003, x-travel 800 mm y-travel 600 mm Nsdjuddgfopfx Ab Aodc z-travel 805 mm Control Sinumerik 840D weight of the machine ca. 13 t 1 horizontal machining centre Make: HECKERT type: CWK 500D year 2003 serial no. 16087 control, make: Siemens, type: Sinumerik 840D travel X/Y/Z 800 x 600 x 805 mm 2-fold pallet changer pallet size 500 x 500 mm NC-rotary table 360 x 0,001° 60-fold tool changer, tool holder HSK 63 Speed max. 15,000 rpm IKZ 50 bar Operating hours 32,450 Spindle hours 6.080 Accessories: Coolant temperature control, belt filter, chip conveyor, spindle cooling, Infrared probe preparation

Condition: ready for operation (used), Year of construction: 1989, total width: 4,000 mm, overall weight: 5,000 kg, workpiece diameter (max.): 140 mm, product length (max.): 2,000 mm, number of axes: 2, This Schaudt Mikrosa SASL 125 was manufactured in 1989. A centerless external grinding machine, it features NC-controlled operations and hydrodynamic axis bearing. Both wheels can be dressed via a controlled axis. Refurbished by UHLMAN Werkzeugmaschinen-Service in 2021/22, it has been regularly maintained. Consider the opportunity to buy this Schaudt Mikrosa SASL 125 centerless grinding machine. Contact us for more information. Retroffited & Overhauled in 2021/22 Working range: • Maximum workpiece diameter • that can be ground • with a grinding wheel Ø 500 mm: 140 mm • Maximum workpiece diameter • that can be ground • with a grinding wheel Ø 630 mm: 80 mm • Minimum workpiece diameter that can be ground: 3.5 mm • Maximum workpiece length for through-feed grinding: 200 mm • Maximum workpiece length in plunge grinding 245 mm • Maximum grindable profile depth on the workpiece 25 mm Grinding wheel: • Maximum outer diameter 500 or 630 mm • Minimum outer diameter 380 mm Nedpfx Abox Enaps Ajdc • Maximum grinding wheel width 250 mm • Grinding wheel bore 305 mm • Guide wheel: • Maximum guide wheel outer diameter 315 mm • Maximum guide wheel width 250 mm • Bore diameter 127 mm Power requirements: • Power consumption approx. 33 kW Additional equipment • Optional: Additional equipment available Machine Benefits Technical Machine Benefits • Hydrodynamic axis bearing • Regular maintenance during series production

Condition: like new (used), Year of construction: 2008, operating hours: 6,200 h, functionality: fully functional, clamping force: 4,200 kN, screw diameter: 75 mm, Krauss-Maffei KM 420-2000 CX Krauss-Maffei injection molding machine, 420 tons of clamping force. Only 6,000 hours of automatic operation. Year of manufacture 2008. MC5 control. Screw diameter 75 mm. Extras: 8 hot runner zones. 2 cores on fixed platen, 2 cores on moving platen. 1 pneumatic valve on moving platen. The injection molding machine is delivered reconditioned by UK Transitus' expert technical team. We can offer commissioning at our clients' facilities, ensuring operation upon completion of the installation. Technical Details 75mm screw Injection pressure: 1635 bar Shot volume: 1237 cm3 Shot weight: 1126 g Maximum distance between plates: 1400 mm Minimum mold thickness: 380 mm Opening stroke: 1020 mm Distance between columns: 900 x 800 mm Plate dimensions: 1270 x 1230 mm 75mm screw Clamping force: 4200 kN Year of manufacture: 2008 Working hours: 6282 Ndjdpfx Aewq D Efeb Aec