Single Column Press - Hydraulic

WMW Zeulenroda PYE 160 S1

Condition: used, Year of construction: 1983, Technical details: Pressure: 160 t throat: 360 mm max. ram stroke: 500 mm distance table/ram: 800 mm clamping plate on table: 1250x630x100 mm passage opening in table: 4x Ø 62mm mm ram speed - forward: 200 mm/s ram speed - reverse: 125 mm/S ram surface area: 450 x 850 mm mortise hole in ram: Ø 49 mm height over floor: 810 mm Itjdpju Nfvusfx Ahvjd total power requirement: 17 kW weight of the machine ca.: 7200 kg dimension machine xH: 2,1 x 1,4 x 3,4 m manual counter *

Condition: good (used), Technical data: Working length: 2050 mm Max. bending capacity: 18.0 mm Pre-bending: 12.0 mm Top roller diameter: 280 mm Bottom roller diameter: 280 mm Conical bending device Hydraulic drop-end bearing Iodpfx Ahjxruvzevstd Motor power: 7.5 kW Dimensions (length x width x height): approx. 3650 x 1550 x 1650 mm Weight: approx. 7.5 tonnes The seller is not liable for typing or data transmission errors. The machine's condition in appearance, technology, and wear corresponds to its age; used machines are sold without any guarantee.

Condition: excellent (used), Year of construction: 1984, total height: 34,500 mm, installation height: 800 mm, total width: 12,500 mm, total length: 22,000 mm, throat depth: 800 mm, pressing force: 160 t, table width: 900 mm, table length: 630 mm, operating speed: 200 mm/s, overall weight: 7,000 kg, reverse speed: 125 mm/s, ram plate width: 700 mm, ram plate length: 450 mm, type of input current: three-phase, stroke length: 500 mm, operating pressure: 160 bar, pressure: 250 bar, oil tank capacity: 500 l, power: 17 kW (23.11 HP), Hydraulic press PYE 160 S/1M. Year of manufacture: 1984. Manufacturer: VEB Wema Zeulenroda (Germany). The machine has undergone a general overhaul. Specifications: Maximum pressing force: 160 tons. Operating pressure: 16 MPa. Upper table: 700 x 450 mm. Lower table: 900 x 630 mm. Daylight opening: 800 mm. Cylinder stroke: 500 mm. Downward speed: 200 mm/sec. Upward speed: 125 mm/sec. Power requirement: 17 kW. Oil tank capacity: 500 l. Weight: 7000 kg. Height: 3450 mm, Length: 2200 mm, Width: 1250 mm. Machine in very good condition. Inspection and test under power possible. Itsdpfx Aheqy E I Roved

Condition: used, Year of construction: 2010, functionality: fully functional, 1 pc Surface Grinding Machine FS 640 SC with Fagor control Itjdjx Dgvqjpfx Ahvod Make: Geibel & Hotz Year of manufacture: 2010 Technical Data Working Area: Grinding area - Maximum grinding area 600 x 450 mm - Standard magnetic chuck size 600 x 400 mm - Clamping area (table to spindle center) 140 - 525 mm - Standard grinding wheel 300 x 50 x 76.2 mm - Table load incl. magnet 600 kg - Grinding spindle motor power approx. 3.7 kW - Total connected load approx. 11 kW - Table speed 2 to 28 m/min - Cross/vertical feed speed 100-1000 mm/min Required space 3.95 x 3.16 x 2.47 m Machine weight approx. 2.1 t Equipment Machine-specific accessories, belt filter system, magnetic separator, extraction unit Magnetic chuck with adjustable holding force, automatic wheel dressing incl. compensation, Dressing diamond, balancing device, clamping device, 4 grinding wheels Technical data subject to change.

Condition: like new (used), functionality: fully functional, How do you do? We are offering used and compatible clamping devices from Erowa. These are suitable for die sinking and milling. Here are some of the available parts: ER-008617 Plug gauge ER-010723 Control mandrel ITS 50 ER-010561 Replacement probe pin ø 2mm ER-010560 Replacement probe pin ø 5mm ER-093992 Square 25 holder C F-Tool holder with square 25 ER-010592 Square 25 Alignment ruler ER-010495 Square 15 alignment ruler ER-129072 Uniplate Collet holder ø 72 ER16-ER50 Table probe with magnetic base 3D probe ø1-5 Steel pallet ø148mm All parts have been cleaned and checked by us. Isdpfx Ahjvby U Sevotd A functional test was also carried out. Spare parts are available. Do you have any questions? Then please do not hesitate to contact us.

Condition: ready for operation (used), Year of construction: 2019, Make: HURCO Type of machine: VMX42i Itodpfx Ajyc Sn Rjhvsd Year of manufacture: 2019 Control system: Hurco WinMax Tool holder: SK40 x-travel: 1.067 mm y-travel: 610 mm z-travel: 610 mm Speed range: 12.000 U/min max. Table load: 1.000 kg Table dimensions: 1.270 × 610 mm Number of tools in the magazine: 24

Condition: good (used), Year of construction: 2000, 1 used 4-roll sheet metal bending machine Brand: Stöting Type: VB 322 Serial number: 1591 Year of manufacture: 2000 With Acon control system Working length: 1000 mm Maximum sheet thickness: 12 mm Iodpfx Ahov Ibkbovjtd Bending capacity: 8 mm Top roll diameter: 250 mm Bottom roll diameter: 210 mm Side roll diameter: 169 mm Dimensions: L: 3200 mm W: 1370 mm Height (without support arm): 1370 mm Drive power: 6.5 kW Weight: 3.2 tons

Year of construction: 2004, condition: used, Ottevanger C5 Containerized Feed mill Itodpfxjq Hr Rze Ahved Automated grinding-mixing line with a capacity of about 5 t/h. Includes the following components, among others. - 55kW Hammer mill 650-375 - 11kW 1000L Mixer PM1000 - Silos - Bucket weigher - Dosing screws - Elevators - bunkers - Switchgear cabinets

Condition: used, Year of construction: 1998, centre height 125 mm centre distance 400 mm Control FANUC 21i Capstan diameter max. 406 mm wheel dimensions 406 x 127 x 40 mm workpiece weight 30 kg longitudinal slide -travel 483 mm cross slide - travel 254 mm total power requirement max. 20 kVA weight of the machine ca. 4,0 t dimensions of the machine ca. 3,0 x 2,0 x 2,1 m including 2 Pcs. internal grinding spindle incl. B axis 1° Hirt, controlled incl. C-axis incl. Quick-Set Probe including Sensitron including Magnetic Jaw Ijdjxwdwfepfx Ahvetd including hydraulically foldable dresser including other small accessories including documentation without a coolant system, as it was previously connected to a central unit Power On hours approx. 71,000 h Spindle hours approx. 25,900 h

Condition: excellent (used), Year of construction: 2017, operating hours: 3,200 h, pressing force: 130 t, Space requirement: 11,500 mm x 10,000 mm + Increased installation height/lift + 230 mm + 4-axis backgauge system + Rear work area lighting + Front work area lighting - TruBend documentation Automation BendMaster (60) Standard equipment: BendMaster - Sturdy base frame and manipulator made of cast aluminum construction - Load capacity 60 kg, sheet plus gripper Iedpsxayl Dofx Ahvjtd - Low-level floor track in welded construction - Sheet sensor for contour detection - Rotary feedthrough for quick gripper change Gripper coupling on the BendMaster - Sensor system for 4-axis backgauge system - Electric drives - Double sheet detection - NC regrip station - Vacuum generation for suction grippers Control - TRUMPF PC control with operator terminal - Teleservice via internet - Convenient operation: screen, mouse, keyboard Safety - Safety fence with access door Special equipment + Track extension to 10 m + Gripper change console + Modular vacuum gripper without separation (materials for 3 grippers) + Modular vacuum gripper with separation (materials for 3 grippers) + Clamp gripper with rotary axis + Sheet removal station with linear axis + Additional pallet for sheet removal station + Right-hand side door for safety fence (or left-hand side in combination with ToolMaster) Machine - Robust machine frame entirely in steel construction - Press beam - Spherical mounting of pressure beam with inclined position - Electro-hydraulic upper drive system with 4-cylinder technology - Optical set-up and positioning assist with control valves - Generous free space for bending - Flat front covers - Block hydraulic system - Electronic pressure gauge - Measuring system with glass scale and spring-back compensation - Hydraulic oil in machine (lifetime lubrication) - Oil cooler - Electrical cabinet cooling via air-to-air heat exchanger - Modern machine design Backgauge System - 2-axis backgauge system, X and R axes Tool Clamping - Hydraulic upper tool clamping - Lower tool holder, hydraulic clamping, hardened - Lower tool displacement, 2 positions, pneumatic Crowning - CNC crowning Control - TRUMPF TASC 6000 - Graphical workshop programming - Windows XPe (embedded), Pentium 4 with 2.8 GHz clock speed - 2 GB RAM - 15-inch touch screen - Network capability - Teleservice via internet Operation - Control panel with LCD keypad and foot switch - Communication rail - MobilControl Safety - Standard safety equipment - CE marking