Used Wmw Bs 25 for sale (459)

Condition: used, bore capacity in steel (diameter) 40 mm continious capacity 25 mm throat 315 mm bore stroke 200 mm bore depth 280 mm spindle taper MT 4 feed range 0,1-1,5 U/min column diameter ca. 230 mm Iodpfxjx Iwgke Ah Nsal number of feeds 9 table-size 700 x 600 mm surface area 450 x 560 mm distance spindle/base plate 1100 mm dimensions ca. 1000 x 700 x 2400 mm total power requirement 2,6 kW weight of the machine ca. 1,1 t emergency stop switch renewed

Condition: used, Year of construction: 1962, frequency 50 Hz voltage 380 V 220 V connected load 2,6 kVA Iasdpfsrxg S Tjx Ah Nel rated current 6,1 A weight of the machine ca. 1 t

Condition: used, Technical details: width: 625 mm depth: 520 mm height: 820 mm weight of the machine ca.: 300 pro Stück kg 2 pieces available (price per piece) without T-slots Oblong hole Ø 33 x 330 mm * Iedpfx Asu S H Stoh Njal

Condition: used, Technical details: pressure: 25 t distance between columns: 360 mm stroke: 500 mm daylight dimension : table/slide up: 800 mm throat: 360 mm Isdpfsu U D I Rjx Ah Noal ram stroke: 500 mm ram speed - forward: 0,200 m/s ram speed - reverse: 0,45 m/s Table dimensions: 630 x 500 x 71 mm passage inside table: Ø 182 mm surface area of ram: 450 x 360 mm mortise hole in ram: Ø 32 x 72 mm ram diameter: Ø 125 mm height over floor: 710 mm total power requirement: 12,5 kW weight of the machine ca.: 2,4 t dimension machine xH: 1,7 x 1,1 x 2,95 m Operation via two-hand control panel (and one-hand operation in set-up mode) Continuous and single stroke TÜV until *

Condition: good (used), Clamping cylinders, hydraulic clamping cylinders, hydraulic clamps, pneumatic clamps, air cylinders, clamping cylinders for power chucks, hydraulic cylinders Iasdpfxowzills Ah Nsl -Manufacturer: WMW, clamping cylinder stroke 20 mm -Type: 25 TGL 30-7311 -Shaft Ø 14 mm -Number: 16x clamping cylinders available -Price: per piece -Dimensions: Ø 35 x 127 mm -Weight: 0.6 kg/pc.

Condition: used, 2 Used Thread Rolling Machines WMW UPW25 ---Only 10.000,00 Euro--- Isdjx Dmnyopfx Ah Nsal

Condition: good (used), Year of construction: 1986, Drilling capacity in steel diameter: 40 mm Drilling capacity in cast iron diameter: 50 mm Throat (arm reach): 320 mm Quill stroke: 185 mm Spindle speeds - stepless: 63 ... 1000 rpm, 9 steps Iaedpfxexbynns Ah Nol Power: 4.2 kW

Condition: good (used), Machine number: 26798 TyP / Model: BS 40 AIII drilling capacity steel / cast iron: 50 / 60 mm spindle mounting: MK 5 Speeds: 32 to 1,400 rpm Feed rate: 0.11 to 1.73 mm/rev table: 780 x 650 mm clamping surface: 630 x 500 mm head height adjustment: 250 mm stroke: 280 mm footprint: 700 x 1.200 mm Iaodpfx Aeiypmxsh Njl total power supply: 6,7 kW accessories/equipment: thread cutting function, right-left run; autom. feed, separate control cabinet condition: good weight: 1,5 t dimensions: 780 x 1.200 x 2.700 mm

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, total height: 27,500 mm, total width: 10,500 mm, total length: 16,500 mm, pressing force: 25 t, table width: 630 mm, table length: 500 mm, operating speed: 100 mm/s, overall weight: 2,200 kg, reverse speed: 450 mm/s, ram plate width: 450 mm, ram plate length: 360 mm, die cushion stroke: 160 mm, clearance between the columns: 800 mm, stroke length: 500 mm, power: 8.75 kW (11.90 HP), Hydraulic press PYE 25 S1M. Year of manufacture: 1990. Manufacturer: VEB Wema Zeulenroda (Germany). Specifications: Maximum pressing force: 25 tons. Iedpfx Ajtzwxdjh Neal Operating pressure: 16 MPa. Upper table: 450 x 360 mm. Lower table: 630 x 500 mm. Clear opening: 800 mm. Cylinder stroke: 500 mm. Downward speed: 100 mm/sec. Upward speed: 450 mm/sec. Power requirement: 8.75 kW. Weight: 2200 kg. Height: 2750 mm, Length: 1650 mm, Width: 1050 mm. Machine is in very good technical condition. Fully overhauled. Inspection and test run under power possible on site.

Condition: used, Technical details: pressure: 25 t stroke: 500 mm daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 0,100 m/s ram speed - reverse: 0,45 m/s Table dimensions: 630 x 500 x 75 mm passage inside table: Ø 180 mm surface area of ram: 450 x 360 mm mortise hole in ram: Ø 32 mm height over floor: 710 mm total power requirement: 8,75 kW weight of the machine ca.: 2,2 t dimension machine xH: 1,7 x 1,1 x 2,95 m Iasdpfxsvc Awxs Ah Nel Operation via two-hand control panel. (and one-hand operation) *

Condition: good (used), Year of construction: 1963, 3 different eccentric presses, manuf. WMW 1 x crank press with one ram 16 t Iajdemi Rpispfx Ah Nol 1 x crank press with one ram 25 t

Condition: good (used), Clamping cylinder, hydraulic clamping cylinder, hydraulic clamp, pneumatic clamp, air cylinder, clamping cylinder for power chuck, hydraulic cylinder -Manufacturer: WMW, clamping cylinder stroke 15 mm Iaedpswziikefx Ah Nel -Type: 25 30-7312 -Shaft Ø 14 mm -Number: 12x clamping cylinders available -Price: per piece -Dimensions: Ø 50 x 96 mm -Weight: 1.2 kg/piece

Condition: excellent (used), Year of construction: 1977, functionality: fully functional, total height: 27,500 mm, total width: 10,500 mm, total length: 16,500 mm, pressing force: 25 t, table width: 630 mm, table length: 500 mm, operating speed: 200 mm/s, overall weight: 2,400 kg, reverse speed: 450 mm/s, ram plate width: 450 mm, ram plate length: 360 mm, distance between stands: 800 mm, stroke length: 500 mm, power: 12.5 kW (17.00 HP), PYE 25 SS hydraulic press. Year of manufacture 1977. manufacturer VEB Wema Zeulenroda (Germany). Parameters: Maximum pressing force 25 tons. Working pressure 16 MPa. Upper table 450 x 360 mm. Ijdpfetzxvwox Ah Njal Lower table 630 x 500 mm. Ground clearance 800 mm. Cylinder stroke 500 mm. Down speed 200 mm/sec. Upward speed 450 mm/sec. Power requirement 12,5 kW. Weight 2400kg. Height 2750mm, length 1650mm, width 1050mm. Technical condition of the machine very good. The machine after a general overhaul. It is possible to make a visual inspection and check the machine in motion.

Condition: used, Technical details: bore capacity in steel (diameter): 22 mm Isdpovxf Irefx Ah Nsal throat: 205 mm bore stroke: 100 mm spindle taper MT: MK2 spindle speed:: 2 step U/min feed: manuell mm/U Distance spindle/table max.: 150 - 600 mm base plate surface area: 350 x 400 mm table clamping surface:: 360 x 280 mm table rotating: 360 ° drill table adjustment: 450 mit Kurbel mm column diameter: Ø 100 mm control voltage: 380 V total power requirement: 0,8 kW weight of the machine ca.: 270 kg dimension machine xH: 0,6 x 0,5 x 1,95 m column drill incl. machine + vice. *

Condition: used, Year of construction: 1971, Technical details: bore capacity in steel (diameter): 16 mm throat: 250 mm bore stroke: 125 mm spindle taper MT: MK 2 spindle speed:: 350 - 2000 / 8step U/min table clamping surface:: 280 x 355 mm table rotating: ja ° drill table adjustment: 520 vertical mm distance table - lower edge spindle: max. 600 mm column diameter: 110 mm total power requirement: 1,1 kW weight of the machine ca.: 272 kg dimension machine xH: 0,6 x 0,5 x 1,8 m Equipment: Isdpfx Aeu Idhmeh Noal -Drill chuck 13 mm -twist drill 10 mm with 45° countersunk cut -machine vice *

Condition: used, Year of construction: 1975, Technical details: faceplate diameter: 3150 mm working area: Ø 4000 mm centre distance: 8000 mm center height: 2240 mm spindle bore: 100 mm revolution per minute: 1,4 ... 71 U/min max. torque on the spindle: 6300 kpm / ca. 61.781 Nm kpm / Nm feed range: plan+längs: 0,355 ... 31,5 / 14 step / R20/3 mm/min rapid traverse speed: 2,0 m/min tailstock quill taper MT: Größe 100 tailstock travel: 400 mm max. workpiece weight between centres: 20.000 kg max. workpiece weight -without tailstock: 8.000 kg main drive motor: 34 kW Ijdsvbhiqepfx Ah Nsal weight of the machine ca.: 44,1 t space requirements approx. LxWxH: 8,0 x 4,7 x 2,72 m Delivery consists of the following components: Headstock with faceplate and main drive 2x support Tailstock Plate fields (3x3.0 meters in a row and 4 additional plate fields) 1x steady rest Ø approx. 350mm 1x steady rest Ø approx. 650mm Support travel (large) X=550mm and X0=220mm / Z=2600mm and Z0=400mm Support travel (small) X=170mm and Z=340mm i.D. *

Condition: excellent (used), Year of construction: 1992, turning diameter over cross slide: 1,600 mm, spindle bore: 100 mm, turning diameter: 2,000 mm, turning diameter over bed slide: 2,000 mm, turning length: 3,700 mm, quill stroke: 210 mm, total length: 8,500 mm, total width: 3,400 mm, total height: 2,060 mm, spindle speed (max.): 450 rpm, spindle speed (min.): 4 rpm, bed width: 1,590 mm, 4 chuck 1600 mm Heidenhain digital read out Steady rest 710 mm Powered tailstock Threath cutting  Triple guide ways cast irion bed design For turbine rotors, electric motor anchors, reactor vessels, cylinders, rope pullys, marine propulsion shaft, castings, shafts and cement industry DBC Turning Length: 3700mm Swing over bed Ø: 2000mm Swing over cross slide Ø:1600mm Spindle bore: 100mm Spindle power: 55kW Bed width: 1590mm Tailstock spindle Ø: 220Ø Stroke quill: 210mm Power: 55kW Iaodeu Avh Ispfx Ah Nel Speeds / ranges: 3,55 - 450Rpm Feed rate X-Axis: 5000mm/min. Feed rate Z-Axis: 5000mm/min. Workpiece load: 12500 Length: 8500mm Width: 3400mm Height: 2060mm Weight: 27400kg

Condition: ready for operation (used), Facing lathe DP 2000 Iedpfov Hx R Nox Ah Neal Chuck diameter 2000 mm Length 3500 mm weight approx. 22 tons

Condition: good (used), total length: 2,035 mm, total width: 1,565 mm, plate height: 255 mm, Manufacturer: ZERBST Type: DP1 / S2 & DP2 / S3 & DP3 / S3 Year of manufacture: 1988 Specifications Metric US Standard Length 2035 mm Width 1565 mm Height 255 mm Weight per plate approx. 1200 kg Number of matching pieces 4 Dimensions (estimated) Iedpewp H Awjfx Ah Njal Length 0 mm Width 0 mm Height 0 mm Weight 0 kg Please note: The information on this page has been provided by us to the best of our knowledge and, where possible, obtained from the manufacturer. The information is given in good faith but accuracy cannot be guaranteed. Accordingly, they do not constitute representations or contractual conditions. We recommend you verify all critical details.

Condition: good (used), WMW BR 40/2 x 1250 radial drilling machine Drilling capacity in steel (diameter): 60 mm Arm reach: 1250 mm Max. workpiece height: 820 mm Spindle speed: 20-1200 rpm Spindle taper: MK 5 Spindle stroke: 400 mm Ijdpfx Aex U Ectjh Nsal Feed rate: 0.063-0.63 m/min Vertical arm adjustment: 950 mm Electrical connection: 380 / 50 V / Hz Clamping surface of base plate: 1400x800 mm Total power requirement: 5 kW Machine weight approx.: 3 t Floor space required approx.: 2.2 x 1.0 x 2.8 m

Condition: used, Year of construction: 1970, taper MK 4 feeds: ja Ijdpexzu Dqjfx Ah Njal weight of the machine ca. 1,5 t

Condition: excellent (used), 250 x 800 Thread Milling Iasdeyaa Hispfx Ah Njl Thread Milling

Condition: good (used), Year of construction: 1969, number of straightening rollers: 7, working width: 2,500 mm, sheet thickness (max.): 39 mm, max. sheet width: 2500 mm Convexity length of rollers: 2700 mm max. sheet thickness (St 50): 32 mm max. sheet thickness (St 34): 39 mm min. sheet thickness (St 50): 8 mm number of straightening rollers: 7 rollers number of driven straightening rollers: 5 rollers diameter of straightening rollers: 290 mm diameter of input/output straightening rollers: 345 mm number of support rollers: 13 diameter of support rollers: 288 mm stroke of upper beam: 120 mm Iaedjx T Eb Tjpfx Ah Nol Straightening speed: 16 m / min Rated power of main drive: 90 kW Total load: 138 kW

Condition: ready for operation (used), Year of construction: 1989, Universal Milling Machine Horizontal - Vertical WMW Auerbach Type FW 250 x 1000 / 2 Year of manufacture: 1989 Table: 1250 x 250 mm Table load: 1250 kg Iaodpfxsx Tqy Uo Ah Nel Travel X/Y/Z: 700 / 400 / 500 mm Heidenhain 3-axis digital readout SK 40 Spindle speeds: 55 – 2800 rpm Feeds: 10 – 630 mm/min, stepless Vertical head Horizontal milling device Drive: 6.3 kW Weight: 2.5 t Price: EUR 2,000 – plus VAT, ex location

Condition: good (used), Year of construction: 1994, throat depth: 360 mm, table width: 630 mm, table length: 1,250 mm, Pressure: 250 t Throat depth: 360 mm Table size: 1250 x 630 mm Table diameter: 250 mm Iasdpfx Asx T Acueh Nel Ram clamping surface: 850 x 450 mm Installation height: 800 mm Piston stroke: up to 500 mm Piston diameter: 400/360 mm Ram speed downward: 200 mm/sec Ram speed upward: 110 mm/sec Total power requirement: 20.5 kW Machine weight approx.: 8 t