Used Pbt 25 for sale (15,133)

Condition: refurbished (used), functionality: fully functional, overall weight: 1,150 kg, total length: 1,680 mm, total width: 1,250 mm, total height: 1,390 mm, Year of construction: 2008, operating hours: 882 h, input frequency: 50 Hz, shaft diameter: 105 mm, type of input current: three-phase, Equipment: emergency stop, rotational speed infinitely variable, Profile bending machine PBT25 PC400 (will be refurbished, including a new Y-axis measuring device) For sale is a profile bending machine PBT25 with PC300 control, manufactured in 2008. The machine will be completely refurbished and technically inspected by PBT before sale. Technical data: Machine type: Profile bending machine Manufacturer / Model: PBT25 Control: PC300 (upgrade in 2026) Year of manufacture: 2008 Operating hours: approx. 882 hours Condition: Good condition. Fully functional. Fgodpfx Aksz Ak I Ioyoh Availability: Approximately two weeks. Further technical details and specifications according to the manufacturer can be found on pbt-ag.com.

Condition: ready for operation (used), functionality: fully functional, actuation type: hydraulic, number of rollers: 3, shaft diameter: 105 mm, empty load weight: 1,000 kg, TECHNICAL DETAILS Power: 3.0 kW Shaft diameter: 105 mm Fsdszdd N Nspfx Akyjgh Number of rollers: 3 Number of driven rollers: 3 MACHINE DETAILS Control: Conventional Drive: Hydraulic Vertical/Horizontal: Horizontal Dimensions & Weight Dimensions (L x W x H): 1,400 x 900 x 1,300 mm Unladen weight: 1,000 kg EQUIPMENT Additional rollers

Year of construction: 2008, condition: used, load capacity: 50 kg, plate length: 2,500 mm, plate width: 1,200 mm, stack height: 1,600 mm, TECHNICAL DETAILS Fgsdpfx Akez Ekcnoysh Maximum panel width: 1,200 mm Maximum panel length: 2,500 mm Minimum panel width: 195 mm Minimum panel length: 250 mm Lifting capacity: 50 kg Operating performance: 18 cycles/min Maximum stack height from the ground: 1,600 mm MACHINE DETAILS Total installed power: 15 kW CE safety compliance: Yes EQUIPMENT Removal of the panel stack via powered roller conveyor Vacuum pump WINDOWS control The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photo documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8347

Condition: used, machine/vehicle number: 516301X00339, Year of construction: 2020, operating hours: 5,917 h, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Lifting height: 4,150 mm Load capacity: 2,500 kg Fork length: 2,400 mm MACHINE DETAILS Mast type: Duplex free-lift mast Drive type: Electric Battery voltage: 80 V Battery capacity: 620 Ah Battery year of manufacture: 2020 Battery voltage in idle state: 85.4 V Fedpfx Akez Iwqkjyegh Mast type: Duplex free-lift mast Dimensions & Weight Dimensions (L x W x H): 4,900 x 1,200 x 2,750 mm Weight: 4,700 kg Service valid until: 05/2027 Safety inspection valid until: 05/2027 Operating hours: 5,917 h EQUIPMENT Former Still full-service unit 3rd and 4th valve Fork positioner Hydraulically adjustable forks Side shifter Semi-cabin Windshield wiper Comfort seat LED work light, front LED work light, rear Orange warning light Safety light, front Safety light, rear If the mast is too high, it can be dismantled for transport upon request and loaded accordingly. All dimensions are approximate. No guarantee is given for typographical or measurement errors. Collection conditions: Side loading up to 6 tons is possible with a large forklift on site. Loading is at your own risk. Rear loading via ramp is possible with a truck height of 100–150 cm, up to 15 tons and up to a width of 230 cm. Collection is only possible after receiving the payment confirmation by email. Collection without prior registration is possible from Monday to Friday between 07:00 and 16:00. A storage fee of €20 per machine and day will be charged if collection is not made on time. Outstanding storage fees must be paid in full before collection. Lot number: 159

Condition: used, functionality: unexamined, Year of construction: 2012, Available for shipment. Machine is operational condition. Fgjdpfx Aoyup R Tjkyoh Ask for additional information including photos and pricing!

Condition: like new (used), Year of construction: 2025, operating hours: 91 h, functionality: fully functional, machine/vehicle number: SMG25/2-S2H-2x085-603/0,48, pressure: 3 bar, operating pressure: 5 bar, total width: 1,500 mm, total height: 1,700 mm, total length: 2,500 mm, type of input current: three-phase, overall weight: 500 kg, inner dimension width: 650 mm, inner dimension length: 450 mm, inner dimension height: 550 mm, input current: 1 A, input voltage: 400 V, space requirement width: 1,500 mm, construction width: 1,000 mm, space requirement length: 3,000 mm, space requirement height: 2,000 mm, Equipment: cabin, compressor, documentation/manual, lighting, MHG blasting system SMG 25 DUO hand blasting booth with double booth. We offer this like-new MHG SMG25/2-S2H-2x085-603/0,48 sandblasting system, manufactured in 2025. Like new: purchased new from MHG in September 2025 as the 2nd machine, and therefore unfortunately used very little. Currently 91 operating hours in 12 months. Identification number: SMG25/2-S2H-2x085-603/0,48 Fsdpfxsz Eq Epj Akyegh Order number: 2025-105286 Serial number: 11429/07/25 Machine color: RAL 7024 Supply voltage: 230/400 V Frequency: 50 Hz Phases: 3 phases + N + PE Rated current L1: 0.9 A Rated current L2: 0.8 A Rated current L3: 0.8 A Fuse: 3 × C 16 A Wiring diagram version: 1.2.5 DEU PLC program version: 1.2.6 DEU If you have any questions or need more information, please send us a message or call us. ----- MHG blasting system SMG 25 DUO hand blasting booth with double booth. Like new: purchased new from MHG in September 2025 as the 2nd machine, and therefore unfortunately used very little. Currently 91 operating hours in 12 months. Further details upon serious inquiry. TYPICAL APPLICATION AREAS Precision engineering Medical technology Extremely small, precise components Laboratory applications Toolmaking WORK AREA 650 x 450 x 550 mm each (W x D x H) BLASTING CHAMBER Dust-tight, under-pressure chamber in a robust steel sheet construction WORK GLOVES Special rubber, abrasion-resistant, inner lining cotton, securely connected to the booth to prevent dust leakage DOORS Two side doors, dust-tight closing, double-walled, sound-absorbing foam filling, lockable, with electrical interlock for safety BLAST MEDIA RECOVERY Via a coordinated MHG recovery system OPERATION Separate for each work area, ON/OFF switch for extraction and lighting, pressure regulator, manometer and foot switch VIEWING WINDOWS Safety glass, 500 x 320 mm each, can be replaced without special tools BLASTING CHAMBER LIGHTING Wear-free, mounted externally, very good illumination by fluorescent tube, optional LED lighting unit MHG BLASTING GUNS High-performance blasting gun, MHG system, with optimal efficiency, operated via foot pedal, available with nozzles in different sizes and materials WORKPIECE BLOW-OFF NOZZLES For cleaning the blasted workpieces and the blasting chamber. ENERGY-SAVING FUNCTION - INTEGRATED IN ALL MHG BLASTING BOOTHS: Clearly arranged in the lamp housing: ON/OFF button for light ON/OFF button for extraction fan Both functions have separate energy-saving times (adjustable in the LOGO). The standard settings are 5 minutes for lighting and 10 minutes for extraction. If the blasting booth is not in use, the lighting will switch off after five minutes and the extraction will switch off automatically after ten minutes. Both functions are reactivated by simply pressing the foot pedal, without the blasting booth having to be switched on manually. When a booth door is opened, the lighting is automatically switched on and the energy-saving time starts again. Maintenance indicator light A "Maintenance" indicator light is located on the control panel. This flashes after 1000 operating hours and is reset by the service department. By adhering to the maintenance intervals, the blasting booth is always kept in an technically optimal condition. www.mhg-strahlanlagen.de/de/strahlanlagen/handstrahlkabinen/smg- 25-duo/

Condition: used, Year of construction: 2008, number of axes: 3, working width: 1,300 mm, working length: 3,200 mm, TECHNICAL DETAILS Working area, X-axis: 3,200 mm Working area, Y-axis: 1,300 mm Fsdpfx Akoz Ekchoyegh Number of controlled axes: 3 Total number of drilling spindles: 36 Tool change stations: 10 MACHINE DETAILS Power of main electric spindle: 11 kW EQUIPMENT Type of machining: Drilling and milling The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents with a descriptive nature. The buyer has the right to inspect the goods before collection and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 7468

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, total width: 2,500 mm, total height: 3,500 mm, input voltage: 400 V, feed length X-axis: 2,500 mm, feed length Y-axis: 3,500 mm, overall weight: 3,550 kg, type of input current: three-phase, power: 17.06 kW (23.20 HP), Equipment: documentation/manual, We are offering this used Lisec VL-1N/25 insulating glass manufacturing machine, manufactured in 2009. Type: VL-1N/25 Serial number: 361-053012 Weight: 3,550 kg Total load current: 24.60 A Apparent power: 17.06 kVA Voltage: 3/N/PE-50Hz 400 V Pressure: 6.00 bar Maximum material load: 250 kg/m Auxiliary current: 8.0 A AC/DC voltage: 400 / 24 V Fgodpfez Nkh Tex Akysh LISEC VL-1N/25 automatic thermal insulating glass sealing robot – 2500 x 3500 mm. Automatic edge sealing unit designed for applying sealant to thermal insulating glass units (primary/secondary). The machine consists of an infeed and outfeed section, as well as a depositing station. A separate measuring unit located in front of the machine measures the thickness of the glass panes, the air gap between them, and the total thickness of the thermal insulating glass unit. The upper edge of the thermal insulating glass unit is guided by a horizontal roller beam. This ensures that the glass units travel at a defined distance in front of the back panel in the sealing sections. Their conveyance is carried out on a patented, wear-resistant transport chain, which supports the lower edge of the unit only minimally, thus leaving the sealing groove free for the application of the sealant. A linear guide vacuum suction system integrated into the back panel ensures that the thermal insulating glass units are conveyed without slipping. The unit can also process polyurethane in 200-liter "A" component + 20-liter "B" component containers, as well as silicone in 200-liter "A" component + 20-liter "B" component containers. The machine can be viewed in operation and will be dismantled in mid-January. If you have any questions or require further information, please send us a message or call us.

Condition: good (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: 2277, turning length: 100 mm, spindle speed (max.): 6,000 rpm, total height: 1,750 mm, total length: 1,800 mm, total width: 1,000 mm, overall weight: 2,100 kg, bar passage: 25 mm, Equipment: documentation/manual, MÜGA GT 2-25 CNC lathe - Number of NC axes: 2 - Maximum swing diameter: 360 mm - Rapid traverse rate: 17.5 m/min Fedpez I Ni Eofx Akyjgh - Collet chuck: ISO DIN 163 E - Clamping range: max. 30 mm diameter - Tool holder, square: 16 x 16 mm, round: 20 mm - Spindle power: 5.5 kW - Tool positions: 7, external: 4, internal: 3 - Includes technical documentation and accessories such as a 3-jaw chuck, chuck jaws, and collets - Includes chip conveyor FCA D-97711 Maßbach – loaded onto a truck

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: H2X387X00082, Year of construction: 2020, operating hours: 17,468 h, load capacity: 2,500 kg, lifting height: 3,000 mm, free lift: 1,500 mm, fuel type: electric, mast type: duplex, construction height: 2,000 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Lifting height: 3,000 mm Free lift: 1,500 mm Overall height: 2,000 mm Load capacity: 2,500 kg MACHINE DETAILS Mast type: Duplex Vehicle type: Electric 4-wheel forklift ISO class: ISO Class 2 = 1,000–2,500 kg Unladen weight: 3,230 kg Battery voltage: 80 V Operating hours: 17,468 h Fjdez I N Uzspfx Akysgh EQUIPMENT Semi-cab Telescopic forks Side shifter Fork positioner 3rd valve 4th valve External reference: SL15009SP

Year of construction: 2022, condition: like new (used), 1 x Ultrasonic deburring machine Ultratec A 25 Year of manufacture: 2022 Fgjdpfoz Ig S Dox Akysh The machine has hardly been used and is in like-new condition. The machine can be inspected while running in its current operating environment.

Year of construction: 2013, condition: used, functionality: fully functional, FOR SALE: WASTEWATER PRE-TREATMENT SYSTEM Due to the expansion and relocation of our winery, the wastewater pre-treatment system, belonging to the ÉSE series of Élinvest Kft., is now available for sale. The system operated flawlessly from 2013 to 2024 with regular maintenance. Technical specifications: Fgjdpfx Aez Eiigokysh Untreated raw wastewater enters an oversized sump below the filter unit, from where a transfer pump with a capacity of approximately 25 m³/h conveys it to the pre-filter unit. The system filters the technological wastewater generated during operation through a Ø1 mm filter screen within 10 minutes of its generation, in automatic mode. Solid materials larger than 1x1 mm are collected in a 240-liter, covered plastic container, while the water phase containing dissolved and suspended solids flows by gravity to a transfer well that also collects municipal wastewater. After the completion of the harvesting operations, the wastewater discharge rate decreases to 20-40% of the harvesting water flow. This water is usually acidic; therefore, the discharge pH can be adjusted by adding a solution of sodium hydroxide (20-30% concentration). A pH control unit, suitable for dispensing both acid and alkali, maintains the pH of the treated wastewater within the specified limits (5.5 and 10). The operation and control are performed by a pH probe and a custom electrical control panel. The rotating drum of the filter unit is cleaned with a rotating brush and an intermittently operating pressure booster connected to a water supply with a minimum pressure of 4 bar. The construction technical approval number for the filter system is ÉME É-61-2011. The average wastewater discharge is 3-10 m³/day. The maximum instantaneous wastewater flow is 10 m³/h, and 25 m³/h in case of an emergency.

Condition: used, Year of construction: 2005, feed rate X-axis: 60 m/min, plate length: 2,500 mm, plate width: 1,200 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum plate width: 1,200 mm Maximum plate length: 2,500 mm Minimum plate width: 220 mm Minimum plate length: 250 mm Fedpfx Akez Ekfceyegh Maximum feed rate: 60 m/min EQUIPMENT 90° transfer conveyor CE safety compliance The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents, which are for descriptive purposes only. The buyer has the right to inspect the goods before collection and is responsible for the installation, securing, and use of the machine at the destination. External reference: 5981

Condition: used, Year of construction: 2008, machine/vehicle number: 1001877, functionality: fully functional, power: 22 kW (29.91 HP), volume flow: 14,100 m³/h, intake vacuum (max.): 450 mbar, suction capacity: 14,100 m³/h, intake manifold diameter: 450 mm, filter area: 125 m², actuation type: electric, total height: 5,800 mm, total length: 2,100 mm, total width: 2,100 mm, overall weight: 2,000 kg, Equipment: CE marking, documentation/manual, dust extraction, Schuko Ecovar extraction system, 14,000 m³/h – complete and operational Complete Schuko Ecovar industrial extraction system for sale, including a 22 kW main fan, a 7.5 kW transport fan, and the corresponding control system. The system is currently in operation and can be inspected while it is running. Due to an expansion of our capacity, this system will be replaced by a larger, new Schuko extraction system. An interesting complete system for companies looking for a powerful used extraction/filtration system with a capacity of approximately 14,000 m³/h. Key features * Capacity: approx. 14,000 m³/h * Filter area: 125 m² * Main fan: 22 kW * Transport fan: 7.5 kW * 100 filter hoses * Electric/pneumatic filter cleaning * Antistatic filter material * Includes the corresponding control system * Complete system * Currently in use and can be inspected while running Technical data for the filter system Brand: Schuko Type: Ecovar 04 22020/25/125, through-flow Design: overpressure, static Number of elements: 1 Material extraction: transport fan Filter material: antistatic polyester needle felt, BIA, AWN 05 Diameter of filter hoses: Ø 160 mm Length of filter hoses: 2,500 mm Number of filter hoses: 100 pieces Filter fabric area: 125 m² Filter cleaning: electric/pneumatic Fedez Egzmjpfx Akyjgh Weight: approx. 2,000 kg Dimensions of the filter system (L × W × H): approx. 2,100 × 2,100 × 6,000 mm Main fan Brand: Schuko Type: S 450/O/L2 Connection diameter: Ø 450 mm Capacity: 14,100 m³/h at 3,412 Pa Motor power: 22 kW Drive: direct Transport fan Brand: Schuko Type: TSK 250/O/S4 Connection diameter: Ø 250 mm Capacity: 4,500 m³/h at 3,344 Pa Motor power: 7.5 kW Drive: indirect Design: reinforced Condition and availability The extraction system is currently operational and is being sold only because it is being replaced by a new Schuko system with a larger capacity. This provides the opportunity to inspect the system while it is running before dismantling. Availability upon consultation. Dismantling and transport upon consultation. Serious interest? Please feel free to contact us for additional information, photos, technical data, or to arrange an appointment to inspect the system while it is running.

Condition: good (used), Year of construction: 1987, machine/vehicle number: 12871, functionality: fully functional, power: 7.5 kW (10.20 HP), input voltage: 380 V, pressing force: 112 t, oil tank capacity: 120 l, total length: 3,300 mm, total width: 2,150 mm, total height: 2,500 mm, overall weight: 10,000 kg, controller manufacturer: DELEM, controller model: EA 22, working length: 3,100 mm, DARLEY EHP 110 31/25 press brake - including foot switch and the bending tool located on the machine Fjdpfx Aksz I N D Njyogh FCA D-35614 Aßlar - loaded onto a truck

Condition: used, Year of construction: 2007, machine/vehicle number: 4801250 / PH06 11 005, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, overall weight: 55,000 kg, year of last overhaul: 2024, clamping force: 3,000 kN, mold height (min.): 1,000 mm, plate length: 2,800 mm, plate width: 2,200 mm, Equipment: CE marking, documentation/manual, For sale is a KraussMaffei LFI shuttle mould carrier for polyurethane processing and backfoaming of large-format components. The system was designed for PU moulding and LFI applications and features a hydraulic clamping unit with a movable lower mould mounting platen. Technical data: Manufacturer: KraussMaffei Type: FT-R-H-25-20-3600.0°.65° Year of manufacture: 2007 KM order number: 39000233 Control system: Siemens S7 Clamping force: 3,000 kN Opening force: 800 kN Parallel stroke: 600 mm Mould mounting platens: 2,500 x 2,000 mm Minimum mould height: 1,000 mm Maximum mould height: 1,500 mm Maximum total mould weight: 10,000 kg Maximum upper mould weight: 5,000 kg Upper mould mounting platen pivotable up to 90° Machine weight: approx. 55,000 kg Operating voltage: 400 V Scope of supply: LFI shuttle mould carrier Hydraulic units Control unit Shuttle / traversing unit Production moulds and temperature control units are not included in the scope of supply. Fgedpoz Dn Ixefx Akyjh Extensive original KraussMaffei documentation is available, including operating manuals, technical drawings, electrical diagrams and spare parts documentation. The machine is fully functional. Inspection under power is possible by prior appointment. The machine is located in the Hamburg area, Northern Germany. The exact location will be provided to qualified prospective buyers. Dismantling, loading and transport are to be carried out by the buyer. Further technical documentation, drawings and photographs are available upon request. Subject to availability.

Condition: used, functionality: fully functional, Year of construction: 2012, operating hours: 15,000 h, includes 3x Brabender gravimetric dosing units includes stand includes chiller includes temperature control unit includes 1x side feed; a second LSB (lateral screw feeder) is also included, and installation is possible on each cylinder. Fodez Eu S Topfx Akyogh More information available upon request. Inspection is possible in Hilpoltstein.

Condition: excellent (used), functionality: fully functional, Year of construction: 2015, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales. Fjdpfx Akjz Ebznsyjgh

Condition: used, Year of construction: 2004, functionality: fully functional, Equipment: documentation/manual, CMZ Turning Center 4 Axes: X, Z, C, B Type: TL 25 BTM Year: 2004 CNC: GE Fanuc Series 18i-TB Video Available Inspection Possible Jaw Chucks: Included ✅ Tool Holder: Included ✅ Documentation: Included ✅ Fedpoz Ih A Defx Akyogh Chip Conveyor: Included ✅

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 280127900226, Year of construction: 2008, operating hours: 16,627 h, load capacity: 25,000 kg, fuel type: electric, No minimum price – guaranteed sale to the highest bidder! Comes with a battery from 2024! TECHNICAL DETAILS Load capacity: 25,000 kg MACHINE DETAILS Drive: electric Battery voltage: 80 V Fgedjz I Nbnspfx Akyoh Battery year: 2024 Unladen weight: 2,390 kg Operating hours: 16,627 h EQUIPMENT Heater Full cab External reference: SL15869SP

Condition: used, Year of construction: 2017, Spiral mixer Sinmag KM-25 Condition: used, fully functional Year of manufacture: 2017 Suitable for a maximum of 12.5 kg of flour or 25 kg of dough Stainless steel bowl and spiral Timer control Two timers Two speed settings Digital control Reverse operation Mobile with locking mechanism Fgedpfx Aksz A Rzxeyoh

Condition: used, Year of construction: 1988, functionality: unexamined, machine/vehicle number: 0210.07382, turning length: 1,000 mm, turning diameter: 350 mm, spindle speed (max.): 3,000 rpm, chuck outer diameter: 315 mm, The Okuma LB 25 is a used CNC inclined-bed lathe, manufactured in 1988, equipped with an Okuma OSP 5020 control. According to the documentation we have, it can handle workpieces up to 1,000 mm in length and has an integrated Okuma Touch Setter. The machine comes with a chip conveyor and oil mist extraction system. It is located in the Düsseldorf area, along with an Okuma LB 15 from 1987. TECHNICAL DATA - Year of manufacture: 1988 - Control: Okuma OSP 5020 - Turning length: 1,000 mm - Turning diameter according to documentation: 350 mm (please verify on the nameplate before purchase) - Chuck diameter according to documentation: 315 mm - Spindle speed max.: 3,000 rpm - Measuring device: Okuma Touch Setter (integrated) EQUIPMENT AND ACCESSORIES - Chip conveyor Knoll 320 S-1 with coolant cleaning - Extraction system Filtermist F21/8 - Tool turret with holders (as shown in the photos) - Turning and clamping tools CONDITION During our inspection on October 1, 2026, the machine was not in operation. We are therefore selling it as untested, in its current condition. We recommend an on-site inspection. AREAS OF APPLICATION For shafts and turned parts up to 1 m in length, suitable for maintenance and contract manufacturing. LOCATION AND PROCEDURE The machine is located in the Düsseldorf area. Inspection is possible by appointment. Disassembly, loading, and transport are organized by the buyer. Upon request, we can provide contact information for freight forwarders in the region. Fedpfsz H Ugyex Akyogh Price upon request. Please contact us via the contact form.

Condition: ready for operation (used), very good condition. Fsdpfez N Sqpex Akyjgh

Condition: ready for operation (used), functionality: fully functional, Maximum straightening pressure: 25 tons Fsdpfez H Nldex Akyjgh Valve stroke: 150 mm Includes straightening unit for shafts.

Condition: used, Year of construction: 2018, overall weight: 600 kg, load capacity: 10 kg, terms of delivery: FCA Pegnitz delivery time: on request terms of payment: 100% prior to delivery Fodpfx Ajz Hfl Hskysgh