Used Weiler Primus 2 Cnc for sale (205)

Condition: ready for operation (used), Year of construction: 1996, turning diameter over cross slide: 340 mm, turning length: 2,000 mm, turning diameter: 570 mm, spindle bore: 83 mm, Weiler Voest Alpine E50 lathe Knodpfx Afon Hp T Asioc Comes with 3-jaw chuck and 6 multifix tool holders

Condition: excellent (used), Parallel Lathe WEILER type PRIMUS Between points: 400 mm Maxi Ø on bench: 250 mm Maxi Ø over saddle: 130 mm Spindle Ø 24 mm Turret Multifix type A Kodpfx Afsxnp I Dsienc 3-jaws chuck Ø 155 mm Threadings Metric + Whitworth Tailstock CM2 Scale HEIDENHAIN ND522 Feeds: auto 2 axes New electrical panel Delivered with: 1 4-jaws chuck Ø 155 mm, 4 tool holders, 1 drill chuck Voltage: 380 V Dimensions (L x W x H): 1300 x 900 x 1900 mm Weight: approx 500 kg Machine in VERY GOOD CONDITION

Year of construction: 1986, condition: used, Weiler Primus lathe year ca.1986, three-jaw chuck , Multifix. Machine in a good condition , By arrangement under power ready for demonstration. Knjdon Ard Dspfx Afijc

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : Knedpfovivmysx Afijc We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Year of construction: 1986, condition: used, Weiler Primus lathe built approx. 1986, three-jaw chuck, Multifix. Machine in good condition, ready for demonstration under power on request. Knedsrhzcmepfx Afioc

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages Knsdpfxsvtp Edj Afiec >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : Knodpfou Aftgex Afisc We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and pull spindle lathe with 2 axis digital readout Heidenhain from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Kjdpeu Afqlefx Afionc Accessories and equipment: >> 2-axis digital readout from Heidenhain >> 1 new three-jaw chuck 125 mm with 2 sets of jaws >> collet chuck device new with collets new from 3 mm to 25 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Back plate To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: used, Year of construction: 2002, Weiler E90 / 4.5M - CNC Lathe with Cycle Automation - Weiler D2 cycle control - Chip conveyor - Approx. 15 pcs. Multifix quick-change toolholders - 1 live centre - Regular servicing by Weiler - Supplied without chuck, without steadies - Year of manufacture: 2002 Technical Data Working Area: - Distance between centres: 4500 mm - Centre height: 450 mm - Swing diameter over bed: 900 mm - Swing diameter over cross slide: 530 mm - Bed width: 600 mm - Travel of cross slide: 590 mm - Travel of top slide: 250 mm - Cross slide length: 1230 mm - Cross slide width: 345 mm - Saddle guideway length: 860 mm - Tool shank cross-section (height/width): 40 x 40 mm Spindle: - Spindle nose according to DIN 55027 / 55026 size: 11 - Spindle diameter in front bearing: 178 mm - Spindle bore: 128 mm - Main spindle internal taper, metric: 140 mm Main Drive: - Spindle nose according to DIN 55027 size: 11 - Total speed range: 1 - 1120 rpm - Speed range gear stage I: 1 - 350 rpm - Speed range gear stage II: 4 - 1120 rpm Ksdjxn Rr Repfx Afienc - Drive power at 60%/100% duty cycle: 45 / 37 kW - Max. torque at spindle: 6000 Nm Feed Drive: - Feed range Z/X: 0 - 20 mm/rev - Feed force Z/X: 20 kN - Rapid traverse speed Z/X: 7 / 3.5 m/min Tailstock: - Quill diameter: 140 mm - Quill stroke: 300 mm - Quill internal taper: MK 6 Thread Cutting Range: - Metric threads: 0.1 - 400 mm - Inch threads: 1/4 - 56 TPI - Module threads: 0.125 - 28 mm - DP threads: 1 - 224 DP Connection Data: - Operating voltage: 400 V - Control voltage: 24 / 230 V - Connected load: 55 kW - Rated current: 85 A Machine Dimensions: - Total length: 6900 mm - Total width: 2600 mm - Total height: 2120 mm - Machine weight: 10,500 kg

Condition: good (used), Year of construction: 2008, Weiler DZ 40, year of manufacture 2008, Siemens 840 D control, travel X/Z 200/350 mm, Y axis +/- 25 mm, tailstock MK 4, main spindle max. bar capacity 42 mm, spindle bore 52 mm, rapid traverse X/Z/Q 30/30/20 m/min, 16-position turret – all stations driven, shank diameter 25 mm, driven tools up to 4,500 rpm, parts tray, accessories, driven toolholders, rigid holders. Kjdpfexnna Sex Afisnc

Condition: ready for operation (used), turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - HEIDENHAIN 3-axis digital display “VRZ 773” - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light Knodpfx Afsxndbljiec - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) - Chip splash guard rear panel - 1x empty tool cabinet - Emergency stop button - Operating instructions

Year of construction: 2007, condition: ready for operation (used), Swing diameter over bed/cross slide: 1100mm/730mm, turning diameter: 1130mm, spindle bore: 128mm, rapid traverse: 5m/min, quill diameter: 140mm, quill stroke: 300mm, center height: 550mm, distance between centers: 3000mm, max. workpiece weight: 6000kg. Machine dimensions X/Y/Z: approx. 6700mm/2600mm/2300mm, weight: approx. 10500kg, control: Siemens, operating hours: 67647h. Documentation available. An on-site inspection is possible. Expected to be available from 2026. Knodpfxsxph N Nj Afiec

Condition: excellent (used), Year of construction: 2014, operating hours: 7,690 h, functionality: fully functional, turning diameter over cross slide: 560 mm, turning length: 530 mm, turning diameter: 240 mm, spindle speed (max.): 5,000 rpm, For sale: CNC lathe, brand Weiler, model DZ 65. The machine is equipped with 12 driven tool stations and is in excellent condition with low operating hours. Package including accessories available for a total price of €65,000. Technical data: Year of manufacture: 2014 Control: Siemens 840D SL Operating hours: 7,690 h Bed arrangement: 45° slant bed Height of spindle center above floor: 1130 mm X travel: 207.5 mm Face length tip: 745 mm Z travel: 530 mm Turning diameter: 560 mm Rated power at 1000 rpm: 27 kW Spindle speed range: 50–5000 rpm Torque: 260 Nm Max. chuck size: 200 mm Spindle bore: 77 mm Spindle diameter at front bearing: 120 mm Bar capacity in draw tube: 65 mm Tailstock NC controlled Center taper: MK 4 Power: 4 MK Torque: 9.5 Nm Longitudinal travel: 525 mm Kjdpfouxc Tcox Afienc Z-axis travel: 530 mm X-axis travel: 207.5 mm Z-axis rapid traverse: 30 m/min X-axis rapid traverse: 30 m/min Number of tool positions: 12 Tool shank cross-section: 20 x 20 mm Tool holder: VDI 30 Dimensions: 3180 mm x 2050 mm x 2200 mm Weight: 6300 kg Additional information: - Bar feeder hardware is pre-installed but requires activation - Supplied with chip tray only, chip conveyor available from Weiler - Equipped with oil skimmer - Offer does not include tool holders and collets, but these can be included upon request Transport and loading can be arranged at extra cost, Europe-wide. Prices are plus VAT. Inspection possible by appointment. Please contact us – our team is happy to support you. Trade-ins or exchanges possible! Machinery purchase/sale BUY/SELL OF PRODUCTION & METALWORKING MACHINES AND MORE. Are you looking for a high-quality yet affordable metalworking machine for your production? Or do you wish to sell your machine? For further information or contact options, please visit our website.

Condition: good (used), functionality: unexamined, machine/vehicle number: 10279, turning diameter over cross slide: 200 mm, spindle bore: 35 mm, turning diameter: 300 mm, center height: 150 mm, turning length: 750 mm, total length: 1,860 mm, total width: 700 mm, total height: 1,800 mm, spindle speed (max.): 2,800 rpm, spindle speed (min.): 40 rpm, overall weight: 1,030 kg, - Operating voltage: 380 V - Connected load: 3 kW - Nominal current: 25 A - Frequency: 50 Hz Equipment: - Tailstock Kodpfx Ajv Irgtefijnc - Multifix type B tool holder - Three-jaw chuck (diameter: 160 mm) - 2-axis digital display from the manufacturer RSF

Condition: used, L + Z Lathe WEILER Type LZ PRIMUS GS Machine no. No. 2461 Year of construction approx. 1990 Center width 400 mm Turning diameter over bed 250 mm Center height above bed 125 mm Turning diameter over support 140 mm Center height above support 70 mm Spindle bore 24 mm Spindle speed 60 - 3000 rpm 18 steps Feed lengthwise and flat Chuck flange short taper DIN 55022 size 4 Inner tailstock taper MK 2 Drive power 1.1 kW and 1.5 kW pole-changing Kodsrtd Uwjpfx Afisnc Mains connection 380 Volt, 50 Hz - 3-axis digital readout FAGOR, type 30i-T-B - Spindle speed via 2 motor speeds and 9 gear stages - 3-jaw lathe chuck RÖHM Ø 125 mm with stepped jaws - MULTIFIX quick-change tool holder with 1 interchangeable cassette - Set of collets Ø 1 / 3 / 4 / 5 / 7 / 8 / 10 / 14 / 15 / 16 / 17 / 19 / 20 / mm - 1 centering tip for collet chuck holder - Emergency stop - Hinged chuck guard - Splash guard - Machine light - electrical diagram - Machine mounted on a steel plate (steel plate L x W x H 1200 x 500 x 30 mm, 140 kg) Space requirement L x W x H 1200 x 900 x 1560 mm Weight 520 kg good condition

Condition: good (used), Year of construction: 2000, Weiler Primus VC, Year of manufacture 2000, Digital display, Center distance 500 mm, Max. turning diameter over slide 150 mm, Spindle speed up to 4,000 rpm, Spindle bore 40 mm, Spindle drive 1.5 KW, Multifix tool holder, 24 longitudinal feeds, Metric thread, Inch thread, Ksdpfsv Ifxiex Afionc

Condition: ready for operation (used), turning length 500 mm turning diameter over bed 297 mm turning diameter over slide rest 160 mm spindle bore 36.0 mm tool adaptor DIN 55022 Gr. 5 quill: 3 MK quill travel 90.0 mm turning speeds 30 - 3550 U/min motor speeds: 1410 / 2830 U/min total power requirement 3.3 kW voltage 380 V weight of the machine ca. 620 kg. range L-W-H 1420 x 700 x 1200 mm from a vocational school - in very good condition (!!) particularly suitable for medium-precision turned parts Features: - Robust lead/feed screw lathe - HEIDENHAIN 3-axis digital display “VRZ 773” - RÖHM three-jaw chuck Ø 160 mm - Foldable lathe chuck guard - Chuck key - MULTIFIX steel holder A, with 3x new inserts - Movable tailstock - Swiveling machine light - Control panel, front left - Automatic feeds for face and upper support - Machine base, with cabinet door (storage space) Kedpfx Afsxnda Ujijnc - Chip splash guard rear panel - 1x empty tool cabinet - Emergency stop button - Operating instructions

Condition: used, Year of construction: 1999, turning diameter 150 mm turning length 500 mm total power requirement 4 kW weight of the machine ca. 0,8 t Knsdpfsvm Dv Dex Afisc

Condition: good (used), WEILER CONDOR VS 2 from university (test laboratory) - Guideways "as new" - Centre height: 165 mm - Swing diameter over bed: 330 mm - Distance between centres: 800 mm - Speed range: 28-2800 rpm - Automatic longitudinal / cross feeds - Spindle bore: 40 mm - Threads / Metric / Inch etc. - Collet quick-change system incl. collets - Four-jaw chuck Röhm Kodpfx Afsxc H Tyoionc - Face plate - Four-jaw face plate - Chuck guard - Multifix with inserts - Emergency stop - Documentation Dimensions: LxWxH 2x0.8x1.6 m / Weight 900 kg Subject to errors / input mistakes.

Condition: used, Year of construction: 2003, turning diameter 0240 mm turning length 525 mm control 840 D Siemens centre height 120 mm turning diameter over bed 450 mm turning dia. over face-slide 300 mm Knjdow U Eifspfx Afioc turning speed range - main spindle max. 5.000 min/-1 power capacity - main spindel 21,5 kW usable bar diameter 42 mm travel -x axis 210 mm travel -y axis 80 mm travel -z axis 525 mm number of toolpositions 16 pos. tool taper VDI 30 Shank diameter 20 x 20 mm rapid traverse X: 24 / Z: 30 m/min Feed force 4,5 kN total power requirement 30 kVA weight of the machine ca. 5 t dimensions of the machine ca. 5,0 x 2,2 x 1,8 m CNC - Lathe with sub spindle. Control Siemens 840 D. Machine has Y- axe and live tooling. We supply an IEMCA VIP 80 bar loader along with the machine and many accessories.

Condition: good (used), 1 used lead and feed screw lathe Make: Weiler Model: Condor VS 2 Technical Data: Centre height: 160 mm Centre distance: 800 mm Spindle bore: 40 mm Bed width: 240 mm Speeds: 12 - 2800 rpm Drive power: 3 kW Tailstock taper: MK 3 Quill stroke: 110 mm Feeds: 0.037 - 1.253 mm/rev Knsdjw Rcrcspfx Afioc Weight, approx.: 800 kg Dimensions (W x D x H), approx.: 1930 x 880 x 1470 mm Equipment: 3-jaw chuck Quick-change toolholder system Multifix

Condition: used, Year of construction: 1999, functionality: fully functional, Equipment: documentation/manual, For sale is a robust and precise cycle lathe WEILER E90 x 4500, year of manufacture 1999, featuring a large swing diameter and cycle control – ideal for heavy workpieces up to 6000 kg. The machine is in technically good condition and was most recently used in industrial production. It is perfectly suited for single-part and small-batch manufacturing of large components. The machine is equipped with cycle control, a steady rest, and a tailstock with large quill travel. Kjdpfow Idx Sjx Afisnc

Condition: ready for operation (used), Year of construction: 1989, functionality: fully functional, machine/vehicle number: 120160, turning length: 925 mm, turning diameter: 480 mm, total height: 1,990 mm, total length: 3,350 mm, total width: 1,800 mm, power: 0.032 kW (0.04 HP), Equipment: documentation/manual, From trade-in from a long-standing existing customer Kedoqy Edgspfx Afionc

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Weiler Primus VC Precision Centre Lathe 3-axis Digital Readout K&C NEW with VC Drive, Stepless Speed Adjustment, and CE Compliance, Very Good Condition Technical Data: Kjdpfew Idllsx Afionc >> Year of manufacture: 2003, Machine No. 646 >> Centre height: 140 mm >> Centre distance: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock Morse taper 3 >> Feeds: from 0.02 to 0.63 mm/rev >> Thread types: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches: from 0.25 to 8 mm >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and Equipment: >> 3-axis Digital Readout K&C NEW >> Collet chuck system with collets from 3 to 26 mm, new, 1 mm increments, NEW >> 160 mm 3-jaw chuck with 2 sets of jaws >> Multifix size A with 2 toolholders >> Electric chip guard >> Machine feet >> Splash guard About the Machine: This offer is for a Weiler Primus VC lead and feed screw lathe, built in 2003 and in very good original condition. A very nice lathe with VC drive and stepless spindle speed control. The digital readout and scales from K&C are new. This newer generation of Weiler lathes is very user-friendly and can produce ground-like surface finishes. The K&C digital readout makes operation even easier and more precise. Take the opportunity to inspect this machine under power on site and be convinced of its condition.

Condition: ready for operation (used), Year of construction: 1989, functionality: fully functional, For sale is a lathe of the brand Weiler type Primus LZ-GS The machine is in very good condition Technical data Year of construction 1989 Ksdpfjihig Ijx Afijnc Machine no. 4443 Operating voltage 380 V Center height 120 mm Center width 430 mm Speed:60 - 3000 rpm in 18 gear stages Spindle clearance 23 mm Short taper spindle head DIN 55027 Tailstock MK 2 Feed rates from 0.03 to 0.15 mm /rev Possible threads metric, inch, module and diametral pitch Metric thread pitches from 0.25 to 2.5 mm Length 1.2 m, height 1.3 m, depth 0.65 m Prices plus VAT Viewing possible by appointment. Contact us, our team will be happy to help you. Trade-in or exchange possible! Machines purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality but inexpensive metalworking machine for your production? Or do you want to sell yours? For further information or contact options, please visit our website