Lead/traction spindle lathe

Weiler Primus

Condition: like new (used), functionality: fully functional, Weiler Primus Lead and Pull Spindle Bench Lathe – Like New Condition!!! Technical Data: >> Year of manufacture approx. 1990, machine no. 4472 >> Center height 120 mm >> Distance between centers 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle bore 23 mm >> Short taper spindle head DIN 55027 >> Tailstock MK 2 >> Feeds from 0.03 to 0.15 mm/rev >> Possible threads: Metric, inch, module, and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 three-jaw chuck, 125 mm, like new, with 2 sets of jaws >> Collet chuck with collets from 2 mm to 12 mm, increasing in 1 mm increments >> Mulifix size A with 3 steel holders >> Change gears >> Fixed steady rest >> Faceplate >> Spindle guard >> Operating manual, electrical diagrams, and much more Ibsdpfx Ajz A Tgqopcob About the machine: A Weiler Primus Lead and Pull Spindle Bench Lathe with a workbench is offered in like-new condition. The machine is, of course, fully functional. All slides run very smoothly and evenly. Even at high speeds, the Weiler runs quietly. This Primus model comes from the German Armed Forces, where it was used very little (almost new). This newer generation of Weiler lathes is very user-friendly and can produce surfaces that are as smooth as if they were ground. Take advantage of the opportunity to inspect this machine on-site and under power to convince yourself of its condition. Digital display available for an extra charge.

Condition: used, Year of construction: 1993, Technical details: sheet width: 3050 mm plate thickness: 6,0 mm distance between columns: 3460 mm no. of strokes: min./max.: 9 / 17 Hub/min back gauge: 750 mm (motorisch) mm Ibedpfxju Rni Ho Apceb cutting angle: 0,5° - 3,0° ° cutting gap adjustment: manuell mm down holder: 18 Stück (hydraulisch) Stück Table dimensions: 380 x 3100 mm total connected load: 7,5 kW weight of the machine ca.: 4,56 t dimensions of machine: L: 3,64 x B: 2,55 x H: 1,58 m Equipment: With side stop L: 1000 × W: 100 × H: 60 mm and stop bar 990 mm, with 8 supports Operation via control panel and foot switch Cutting zone lighting Stroke counter Machine feet *

Condition: used, Year of construction: 1999, turning diameter over bed 280 mm Ibjdpfx Ajz Abw Hepcob turning diameter over slide rest 150 mm turning length 500 mm center height over bed 140 mm centre distance 500 mm bed width 205 mm spindle bore 40 mm turning speed range - stepless 30 - 4.000 U/min 3-jaw-chuck diameter 140 mm quick change toolholder MULTIFIX Typ A drive capacity - spindle motor 4,0 kW taper in tailstock-quill MK 3 dia. of quill 40 mm quill stroke 85 mm voltage 400 V total power requirement 7,5 kW weight of the machine ca. 800 kg dimensions of the machine ca. 1,40 x 0,95 x 1,55 m - Serial-No.: 154 - SIEMENS 3-axis digital display - MULTIFIX quick-change tool holder - rotating centering tip

Condition: ready for operation (used), turning length 450 mm turning diameter over bed 245 mm turning diameter over slide rest 135 mm spindle bore 23.0 mm tool adaptor DIN 55021-4 quill: 2 MK quill travel 80.0 mm turning speeds 60 - 3000 U/min bed width 155 mm total power requirement 1.2 / 1.5 kW voltage 380 V weight of the machine ca. 340 kg. range L-W-H 1200 x 650 x 1330 mm from a vocational school (!) particularly suitable for precision turned parts The Primus series is the most compact precision sliding headstock and sliding headstock lathe(LZ) from WEILER. It is used in toolmaking, laboratories and Ibjdpozbc Dajfx Apcob training workshops as an absolute machine for precise work in the tightest of spaces. The machine is built for extremely tight tolerances. The hardened and ground machine bed ensures maximum for maximum vibration damping and durability. Features: - Robust lead/traction spindle lathe - 2-axis digital readout "D60-2V" - three-jaw chuck - Folding lathe chuck guard - chuck key - MULTIFIX steel holder with 3x inserts - Sliding tailstock - Control panel, front left - infinitely adjustable feeds for flat and top support - Pole-changing drive motor - machine base frame - Chip guard rear panel - Additional accessories such as collet holder Collets etc. - EMERGENCY OFF button at the front

Condition: new, Year of construction: 2025, x-travel 580 mm y-travel 200 mm z-travel 340 mm speeds 115 - 1750 U/min table surface area 1000 x 240 mm tool taper ISO 40 total power requirement 4,5 kW weight of the machine ca. 820 kg dimensions of the machine ca. 1290 x 1090 x 2170 mm Universal precision drilling and milling machine for horizontal and vertical milling work with digital 3-axis position display DPA 31 Plus Iodpfetv Riaox Apcsbb Description: - Heavy, solid design made of high-quality, vibration-absorbing gray cast iron - Oil bath gear with ground, hardened gear wheels - Coolant system - Halogen machine lamp with bundled beam - Solid and large cross table, precisely surface-machined with T-slots and adjustable wedge strips - Milling head can be tilted ± 45° - Right/left rotation - X-axis moves either with the handwheel or via the table feed device - Automatic limit switch on the X-axis - Height-adjustable protective screen with microswitch, against flying chips and parts, for the greatest possible protection of the user Scope of delivery: - Gear rim drill chuck 1 - 16 mm / B 18 - Arbor drill chuck ISO40 / B18 - Horizontal milling spindle with counter bearing, disc milling cutter holder Ø22 mm, Ø27 mm - Adapter ISO 40/MK3 - Adapter ISO 40/MK2 - Vertical and horizontal drawbar - T-slot nuts - Drifter - Operating tool

Condition: ready for operation (used), turning length 450 mm turning diameter over bed 245 mm turning diameter over slide rest 135 mm spindle bore 23.0 mm Iedpfx Aezbc Dtjpcsbb tool adaptor DIN 55021-4 quill: 2 MK quill travel 80.0 mm turning speeds 60 - 3000 U/min bed width 155 mm total power requirement 1.2 / 1.5 kW voltage 380 V weight of the machine ca. 340 kg. range L-W-H 1200 x 650 x 1330 mm from a vocational school (!) particularly suitable for precision turned parts The Primus series is the most compact precision sliding headstock and sliding headstock lathe (LZ) from WEILER. It is used in toolmaking, laboratories and training workshops as an absolute machine for precise work in the tightest of spaces. The machine is built for extremely tight tolerances. The hardened and ground machine bed ensures maximum for maximum vibration damping and durability. Features: - Robust lead/traction spindle lathe - 2-axis digital readout "D60-2V" - three-jaw chuck - Folding lathe chuck guard - chuck key - MULTIFIX steel holder with 3x inserts - Sliding tailstock - Control panel, front left - infinitely adjustable feeds for flat and top support - Pole-changing drive motor - machine base frame - Chip guard rear panel - Additional accessories such as collet holder Collets etc. - EMERGENCY OFF button at the front

Condition: excellent (used), functionality: fully functional, Weiler Primus lathe in excellent condition. Can be inspected while powered on. Technical data: Center distance: 450 mm Center height: 120 mm Isdpfx Aex Htf Hopcsbb Spindle bore: 23 mm Speed: 30 – 3000 rpm Tailstock: MK 2 Drive power: 1.5 kW Weight: 350 kg Dimensions: 1200 x 650 x 1550 mm Price reduced!

Condition: good (used), Year of construction: 1989, turning diameter over cross slide: 820 mm, spindle bore: 128 mm, turning diameter over bed slide: 515 mm, turning length: 2,000 mm, total length: 6,000 mm, total width: 1,900 mm, total height: 1,800 mm, spindle speed (max.): 1,400 rpm, Centre lathe VDF BOEHRINGER - DUE 800 MACH-ID 9760 Make: VDF BOEHRINGER Type: DUE 800 Year: 1989 3 Axis HeidenHain ND780 dro 3 chuck 400 mm 4 chuck 800 mm Steady rest closed ca 400 mm Steady rest C-Type ca 400 mm DBC Turning Length: 2000mm Swing over bed Ø: 820mm Swing over cross slide Ø:515mm Spindle bore: 128mm Spindle power: 30kW Bed width: 560mm Speeds / ranges: 1400Rpm Quill Ø: 125mm Workpiece load: 5000 Iodpfxjzpwwpo Apcsbb Length: 6000mm Width: 1900mm Height: 1800mm Weight: 6700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1981, machine/vehicle number: 283, Item No. 26208 Technical Data: - Maximum turning height 120 mm - Maximum turning diameter 450 mm - Maximum swing over bed 250 mm - Spindle bore 23 mm - Spindle mounting with threaded nose DIN 55027 - Taper of tailstock spindle MK 2 - 20 spindle speeds 60 - 3000 rpm - Feeds - longitudinal 0.03 - 3.0 mm - transverse 0.015 - 0.150 mm - Thread pitches 0.25 - 5 mm - Drive 400 V / 1.1 / 1.5 kW - Footprint approx. approx. W 1200 x H 1250 x D 650 mm - Weight approx. approx. 700 kg - Including: - 3-jaw chuck Ijdpfx Apezyl H Hscsbb - Quick-change tool holder - Rotating center - Separate tool cabinet with various accessories

Condition: good (used), Turning diameter 160 mm Turning length 500 mm Swing diameter over bed 400 mm Swing diameter over cross slide 220 mm Main spindle Main spindle bore 51 mm Ibedpfxezwpl Ij Apcob Spindle speed 5,000 rpm Bar diameter 42 mm Chuck diameter 160 mm Number of tool positions 12 Tailstock quill stroke 50 mm Tailstock spindle taper MK3 Travel - x 250 mm Travel - z 550 mm Total power requirement 30 kW Machine weight approx. 4,000 kg

Condition: good (used), x-travel 400 mm y-travel 375 mm z-travel 250 mm table-size 205 x 800 mm T-slots 4 x 45 14 H7 speeds 50 - 3150 U/min tool taper 40 ISO quill stroke 50,0 mm Feeds X + Z Axis 5.0 - 1000 mm/min Feeds Y Axis 5.0 - 670 mm/min rapid traverse 2.4 / 1.6 m/min control Heidenhain total power requirement 5.1 kW weight 950 kg range L-W-H 1860 x 1790 x 1750 mm Machine from a vocational training center In good condition (!!) Equipment: - MAHO universal tool milling/drilling machine - HEIDENHAIN "TNC 135" positioning/path control * 3-axis manual data input control * Programmable by the machine operator * Convenient and easy operation - Electric motor-driven feed rates in all axes (X/Z/Y) * X and Z axis: 5.0 - 1000 mm/min with rapid traverse of 2.4 m/min * Y axis: 5.0 - 670 mm/min with rapid traverse of 1.6 m/min - Tiltable milling head to both sides - Tiltable T-slot universal table - Vertical clamping range - Continuously variable speed adjustment - Manually extendable spindle sleeve - Hardened and ground guideways - Electro-hydraulic tool clamp - Coolant system Ibodpfx Aoxl E Syspcjb - Front coolant tank - operating instructions

Year of construction: 1986, condition: used, Weiler Primus lathe year ca.1986, three-jaw chuck , Multifix. Machine in a good condition , By arrangement under power ready for demonstration. Ibjdpfxsn Ard Dj Apcsb

Condition: ready for operation (used), Year of construction: 2018, spindle speed (max.): 4,000 rpm, travel distance X-axis: 150 mm, travel distance Z-axis: 500 mm, spindle motor power: 4,000 W, total height: 1,700 mm, total width: 890 mm, overall weight: 1,050 kg, bar diameter (max.): 43 mm, product length (max.): 1,570 mm, workpiece diameter (max.): 280 mm, number of slots in tool magazine: 4, number of axes: 2, Horizontal turning machine manufactured in 2018. This Weiler PRIMUS VCD features a connected load of 7.5 kVA and operates at a nominal current of 15.5 A. With a machine weight of 1050 kg, it is designed for robust performance. If you are looking to get high-quality turning capabilities, consider the Weiler PRIMUS VCD machine we have for sale. Contact us for further details. • Machine Type: Centre Lathe • Turning Length / Distance Between Centres: 500 mm • Swing Over Bed: 280 mm • Swing Over Cross Slide: 150 mm • Spindle Nose (DIN 55027): Size 5 • Front Bearing Diameter: 70 mm • Spindle Bore: 43 mm • Main Spindle Internal Taper: ME 50 • Drive Power (100% Duty Cycle): 4 kW • Spindle Speed Range: 30 – 4,000 rpm • Number of Feed Rates: 24 • Longitudinal Feed Range: 0.02 – 0.63 mm/rev • Cross Feed Range: 0.006 – 0.20 mm/rev • Metric Thread Range: 0.25 – 8 mm • Inch Thread Range: 80 – 2 TPI • Module Thread Range: 0.25 – 4 Module • Diametral Pitch (DP) Thread Range: 200 – 5 DP • Tailstock Quill Diameter: 40 mm • Tailstock Quill Travel: 85 mm • Tailstock Taper: MT3 • Operating Voltage: 400 V Ibedpfezpwh Uox Apcjb • Control Voltage: DC 24 V • Connected Load: 7.5 kVA • Nominal Current: 15.5 A • Frequency: 50 Hz • Main Fuses: 25 A • Machine Weight: 1,050 kg • Machine Dimensions (L × W × H): 1,570 × 890 × 1,700 mm Additional Equipment • 4-Position Quick-Change Tool Post PARAT Size 1, incl. 1 × WD 1/12 Tool Holder • 2 × WD 1/12 Tool Holders • Lever-Operated Collet Chuck for 173 E Collets • 13 × 173 E Collets, Clamping Range: 3–15 mm (1 mm Increments) • Fixed Steady Rest with Roller Jaws, Capacity: 15–100 mm • Movable Chip Splash Guard with Viewing Window • 8 × Levelling Elements Technical Specification Counter Spindle No Driven Tools No

Condition: excellent (used), Year of construction: 1992, functionality: fully functional, Universal Milling Machine Deckel FP4M with 3-Axis Active Digital Readout Heidenhain, Excellent Condition, CE Compliant!!! Technical Data: Ijdpfju Tuk Hjx Apcjbb - Year of manufacture: 1992, Machine no. 2203-8449 - Fixed angle table - Spindle speed: 50 - 2500 rpm - Feed rate: 8 – 630 mm/min - Drive power: 3.7 / 4.4 kW - Spindle brake - Rapid traverse: 1300 mm/min - Travel (X/Y/Z): 500/400/400 mm - Vertical milling head traverseable on column - Vertical and horizontal quill - SK40 taper - Vertical quill extendable by 90 mm - Hydraulic drawbar system - Approx. weight: 1600 kg Equipment and Accessories: - 3-axis active Heidenhain digital readout - Coolant system - Chip tray - Central electric lubrication - Operating manual, spare parts drawings About the Machine: For sale is a Deckel FP4M Universal Milling Machine (Active) in very good condition. The machine has minimal backlash, and all slides move smoothly. Even at maximum spindle speeds, the milling machine runs quietly. The machine features hydraulic tool clamping. The FP4M was only occasionally used in a state-run facility for training purposes. On this newer FP4 model, the feed rates are steplessly adjustable in all three axes, and each axis also features a rapid traverse. A major advantage is the active 3-axis digital readout. With the Heidenhain control, you can input measurements that the machine will approach automatically. Oil change has been performed; mechanically and electrically tested. The Heidenhain digital readout makes work easier and even more precise. Take advantage of the opportunity to inspect and test this machine under power on site.

Condition: excellent (used), functionality: fully functional, spindle bore: 40 mm, center height: 140 mm, center width: 500 mm, spindle speed (max.): 4,000 rpm, Equipment: rotational speed infinitely variable, Dear Sir or Madam, We are offering for sale a WEILER Primus VC lathe. This model series is particularly distinguished by the Siemens control panel and the fully stepless speed regulation. As the name suggests, the VC can operate with constant cutting speed. The machine has undergone extensive inspection in our workshop and is in excellent geometric, technical, and visual condition. All guides are in good order, the gearboxes run quietly, and the levers are easy to operate. We cordially invite you to test the Primus VC at our premises. We look forward to your inquiry! Availability: Immediately Centre height: 140 mm Centre distance: 500 mm Spindle bore: Ø 40 mm Tailstock taper: MK3 Quill stroke: 85 mm Available thread types: Metric, inch, module, diametral pitch Metric thread pitches: 0.25 - 8 mm Spindle brake: switchable Voltage: 400 V Dimensions: approx. 1.50 x 1.00 x 1.50 m (L x H x W) Weight: approx. 700 kg Additional equipment and accessories: Siemens control panel, coolant system, chuck guard, leadscrew and feed shaft cover, emergency stop, operating manual, CE declaration of conformity, and much more on request. Isdpeyalursfx Apcebb Our service promise to you: - We are a certified master company in the field of mechanical engineering - All machines are at least workshop-tested - All lubricants and, if necessary, worn parts are replaced in advance - Upon request, we can perform a complete or partial overhaul of your chosen machine - Upon request, we can repaint your chosen machine in the color of your choice - Upon request, you can order additional accessories such as tools directly - Upon request, we can install further accessories such as safety features - We are happy to handle shipping and/or installation for you