Used Vertical Milling for sale (14,947)

Condition: used, Year of construction: 2008, x-travel 600 mm y-travel 450 mm z-travel 300 mm spindle tunring speed 42.000 U/min In our opinion, the machine is in good used condition and can be inspected under power by appointment. Equipment: - Extraction system, Keller - Pallet system, Röders RC 2 Accessories, tools and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Ledpfx Ajx Iwg Djiishh Subject to changes and errors in the technical data and information as well as prior sale!

Condition: used, Year of construction: 2023, x-travel 3000 mm y-travel 820 mm z-travel 720 mm Ledpfxjyvvluo Aiiohh Control Mazatrol Smooth G spindle taper SK 40 spindle turning speed range 35 - 12.000 U/min spindle motor 15 kW distance spindle centre table top edge 140 - 860 mm table load 2500 Kg rapid travel x/y/z 50 m/min table width 3500 mm table length 820 mm table height over floor 870 mm T-slots 7 T-slot - width 18 mm T-slot - distance 100 mm tool change unit 48 tool changing time 4,7 sec wotkpiece diameter with 2 vacant positions 130 mm workpiece diameter at full load 80 mm max. tool weight 8 kg tool length - max. 350 mm air pressure - required 5 - 9 bar Air volume 260 l/min electrics - voltage/frequency 400 / 50 V/Hz coolant tank 500 l total power requirement 46,7 kW weight of the machine ca. 15,4 t dimensions of the machine ca. 5,3 x 3,6 x 3,3 m Standard machine including the following optional extras: - Provision for dual oil mist extraction - Air cooling via the rotating milling spindle - 48-tool magazine - Pulse handwheel - 3-colour LED signal light - Additional work area lighting - Air blow-off device on the milling spindle - High-pressure coolant supply through the spindle (15 bar) - Provision for MAZAK Monitoring - Chip conveyor with left-hand ejection (Crowther) - Manual grease gun - Grease cartridge - Mazak API - Drilling cycle with automatic chip breaking - Synchronous thread cutting - Rapid traverse with constant angle of inclination STANDARD ACCESSORIES Adaptation for the European market USB port (1 port) Mazak standard colour Work area lighting SAFETY FEATURES Operator door with interlock switch Work area cladding The splash guard enclosure encloses the work area from the side. Fully enclosed work area Protection against chips, coolant and access to the work area during automatic machining. Safety precautions in accordance with global standards COOLANT SUPPLY Coolant supply via spindle (pump pressure = 5 bar) Complete coolant system includes pumps, valves, pipework and nozzles for the efficient production of high-quality components. FACTORY AUTOMATION Automatic start/stop and warm-up function Automatic activation of a warm-up via digital timer MEASURING SYSTEM Tool length measurement and tool breakage detection NUMERICAL CONTROL Horizontally adjustable NC control panel Relocation Detector Mazatrol SmoothG control 19" colour LCD screen (touch screen) Mazak Tornado tapping/drilling cycle (Mazatrol) EIA/ISO input function Tool path verification in the background 3D coordinate conversion Shape compensation for rotating axes Mazacc-2D software (contour correction) Mazacc-3D software package MAZACC-3D high-speed software package (NO456) is additionally required. Control system with high smoothing Interface for LAN SD memory card interface Smooth Standard Software for M/C - NO443 B) MAZACC-2D software (workpiece shape compensation) - NO444 D) MAZACC-3D high-speed software package - NO445 B) Shape compensation for rotating axes - NO497 D) High-precision control for finishing - Seamless corner point control - Variable acceleration control - Ultra-high-speed machining mode - NO498 Rapid traverse paths, rounding function Absolute positioning system - All dimensions, weights and performance specifications are subject to change - - Used machine without warranty - - Subject to prior sale -

Condition: used, Year of construction: 2019, x-travel 1300 mm y-travel 670 mm z-travel 625 mm control Siemens Sinumerik 828D Lodpjyzt Anofx Aiijhh weight of the machine ca. 8500 kg

Condition: used, Year of construction: 2019, x-travel 2.000 mm y-travel 820 mm z-travel 720 mm Control Mazatrol Smooth G spindle taper SK 40 spindle turning speed range 35 - 12.000 U/min spindle motor 22 kW distance spindle centre table top edge 140 - 860 mm table load 1700 Kg rapid travel x/y/z 50 m/min table width 820 mm table length 2500 mm table height over floor 870 mm T-slots 7 T-slot - width 18 mm T-slot - distance 100 mm tool change unit 48 tool changing time 4,7 sec wotkpiece diameter with 2 vacant positions 130 mm workpiece diameter at full load 80 mm max. tool weight 8 kg tool length - max. 350 mm air pressure - required 5 - 9 bar Air volume 260 l/min electrics - voltage/frequency 400 / 50 V/Hz coolant tank 450 l high-performance coolant system 25 bar total power requirement 46,7 kW weight of the machine ca. 14,8 t dimensions of the machine ca. 4,3 x 3,6 x 3,1 m STANDARD ACCESSORIES Transformer for the European market USB port (1 port) Mazak standard colour Spindle speed 12,000 min-1 (steep taper 40) Work area lighting SAFETY DEVICES Operator door with locking switch Work area panelling The splash guard encloses the working area from the side. Fully enclosed work area Protection against chips, coolant and access to the work area during automatic machining. Safety precautions in accordance with global standards COOLANT SUPPLY Coolant supply through spindle (pressure at the pump = 5 bar) Complete coolant system includes pumps, valves, pipework and nozzles for the efficient production of quality components. FACTORY AUTOMATION Automatic switch on/off and warm-up function Automatic switch-on of a warm-up cycle via digital timer MEASUREMENT SYSTEM Tool length measurement and tool breakage detection CHIP DISPOSAL Factory preparation for chip conveyor (left) NUMERICAL CONTROL Fixed control/operating unit Relocation Detector Mazatrol SmoothG control unit 19" LCD colour screen (touch screen) Mazak tapping/drilling cycle Tornado (Mazatrol) By drilling and tapping in helical machining mode, a wide range of diameters a wide range of diameters can be machined at high speed with a wide range of diameters can be machined at high speed with just one tool. This function minimises programming and machining times. EIA/ISO input function Tool path check in the background The tool path of a programme can be checked even if another programme number is programme number is called up and processed in automatic mode. Ledpfx Aotuggceiijhh 3D coordinate conversion Shape compensation for rotating axes Mazacc 2D software (contour correction) Accuracy is maintained at high feed rates. Mazacc-3D software package for high-speed machining High-speed and high-accuracy machining for contours defined in the finest programme contours defined in the finest programme increments. MAZACC-3D high-speed software package (NO456) is additionally required. Control with high smoothing Interface for LAN SD Memory Card I/F Smooth standard software for M/C - NO443 B) MAZACC-2D software (workpiece shape compensation) - NO444 D) MAZACC-3D high-speed software package - NO445 B) Shape compensation for rotating axes - NO497 D) High accuracy control for finishing operations - Seamless corner point control - Variable acceleration control - Ultra high speed machining mode - NO498 Rapid traverse paths Rounding function Absolute positioning system Machine incl. the f...

Condition: like new (used), 1 unused universal vertical milling head, suitable for an ORADEA / EURO-MILL FUS 32 Design: “MAHO”, ISO 40 shank, quill stroke 100 mm, designed drive power approx. 3-4 kW, max. speed 2000 rpm, … Optional accessories: - Multiplier, gear ratio 1:4, ISO 40 shank Price: EUR 499.00 - Attachment for automatic feed device for the vertical milling head quill, “MAHO” system, 6 feeds 0.02 - 0.2 mm/rev Price: EUR 1,880.00 - Cross milling head, additional head for the vertical milling head with spindle taper ISO 30, rotatable, 360 degrees Price: EUR 585.00 plus statutory VAT. Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel / Germany Lhsdpfoddtwbsx Aiioh

Condition: used, Year of construction: 2004, x-travel 510 mm y-travel 355 mm z-travel 405 mm table surface area 786 x 355 mm control Kitamura spindle turning speed range 150 - 15.000 U/min spindle taper SK 30 table load 240 kg rapid traverse X/Y/Z axis 50/50/36 m/min ATC 20 Pos workpiece diameter at full load 70 mm tool diameter if 2 vacant positions 100 mm tool length - max. 200 mm Ledpfx Ajym D Auoiijhh weight of tools max. 2 kg total power requirement 15 kVA weight of the machine ca. 4 t dimensions of machine L x W x H 2,4 x 2,1x 2,63 m

Condition: used, CNC 3+2 axis vertical machining center DECKEL MAHO type DMU 35 M CNC control SIEMENS 810D with ShopMill Manufacturer no. 11065353554 Year of manufacture 2001 Travel paths: X: 350 mm, Y: 240 mm, Z: 340 mm Table movements: C-axis: 360° Swivel range: +105° / -15° Universal swivel - rotary table: 400 x 290 mm, center hole 30H6 Table load: max. 100 kg Distance spindle nose - table: min. 145 mm to max. 485 mm Feed rate: 5,000 mm/min Rapid traverse (X / Y / Z): 5 m/min Input resolution: 0.01 mm Total power requirement: 15 kVA Speed range - main spindle: 20 - 6,300 min/-1 Drive power - main spindle: 6.3 / 10 kW (100% / 40% ED) Torque: max. 55 / 80 Nm Tool holder: SK 40 DIN 69871 Pull bolt: DIN 69872 or ISO 7388/2 Type B Interface: Serial RS232C, LAN (RJ45) Power connection: 400 volts, 50 Hz, 15 kVA Compressed air connection: 6 bar - CNC control Siemens Sinumerik 810D with ShopMill V05.03.22, NCU 03.03.34-CCU1E, MMC103 - 3-axis controlled (X, Y and Z axis) Lsdpfevt D D Usx Aiiohh - Manual swivel rotary table, C axis = table rotation 360°, B-axis = swivel range +105°/ -15° - direct path measuring system for all 5 axes - electronic handwheel - spindle drive via servo motor with toothed belt and 2 gear stages - fully protected cabin with sliding door - swiveling control panel - coolant nozzles on the vertical head - chip tray with coolant container and cooling lubricant pump - work area lighting - documentation available space requirement L x W x H 2000 x 2000 x 2100 mm weight 1750 kg good condition

Condition: used, Machine has a defect in the main spindle CNC vertical machining center CHIRON type FZ 22 L high speed Machining center with CNC control FANUC Series 21-M serial no. 179-98 year of construction 1999 Travel X: 2000 mm, Y: 520 mm, Z: 630 mm Table size 2700 x 570 mm Table load 525 kg (per meter) Tool holder SK 40 (DIN 69871) Drilling capacity 35 mm Tapping capacity M27 Tool diameter 75 mm Diameter with free secondary positions 105 mm Tool change speed tool - tool 2.0 sec. Tool change speed from chip to chip 4.8 sec. Distance spindle nose - table 190 to 820 mm Spindle speed max. 10,500 rpm Main spindle drive max. 18.5 kW Mains connection 400 Volt, 50 Hz, 32 kVA - Pendulum machining over 2 work areas (partition wall missing) - CNC control FANUC Series 21-M - Tool changer 40-fold - IKZ = internal coolant supply through the spindle - Spray protection cabin with sliding door - Indirect measuring system - Coolant device with chip conveyor opposite - Electronic handwheel Transport dimensions of the basic machine L x W x H 4600 x 2470 x 2950 mm Weight of the machine approx. 7.5 tons. Transport space requirement on the truck L x W x H 12000 x 2470 x 2950 mm Transport Weight on the truck approx. 10 ton. Weight 7.2 tons. Ljdpfx Ajquhbgeiishh good condition - machine has a defect on the main spindle

Condition: used, Keyway milling head for milling machine, milling head, CCCP / USSR STANKO Type 1502 No.: 200 Year of manufacture: 1974 Stroke size: max. 60 mm Stroke rate: approx. 200 - 500 strokes/min. Tool holder: 12 x 17 mm with clamping plate Hole spacing machine flange plate: 245 x 185 mm Lhoded Dk A Aopfx Aiish Mounting hole: Ø 17 mm Centering diameter on the machine flange plate: 190 mm - Stroke size adjustable via eccentric adjustment - The drive is the same as for the standard vertical head, driven by the machine gearbox - Drive via a drive pin, centered within the centering diameter - Graduated scale on the flange plate, +/- 45° infinitely adjustable - This keyway milling head is flanged in place of the standard vertical milling head (Mounting in place of the vertical milling head) Weight: 42 kg Good condition Keyway milling head, bearing number 58166, and vertical milling head, bearing number 58164, from an identical STANKO milling machine.

Condition: used, Year of construction: 1971, x-travel 2000 mm y-travel 1000 mm z-travel 1000 mm Control Heidenhain type TNC 430 spindle turning speed range 15-1450 U/min Table area 2300x1200 mm Spindle 200 mm spindle stroke 200 mm Ljdpfx Aisyt R Dxoiehh Maschine wurde überholt machine is retofit The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Year of construction: 2017, x-travel 1200 mm y-travel 600 mm z-travel 630 mm control Heidenhain weight of the machine ca. 7700 kg Lhodpfjyrt Anjx Aiijh

Condition: good (used), Year of construction: 1996, Travel X/Y/Z 600/500/450 mm, Control HEIDENHAIN TNC 410 PA, spindle power 9,0 KW, spindle speed 5-6300 rpm, ISO40, table size 530x900 mm, max. table load 400 kg, tool changer 22 places, dimension 2200x2700x2050 mm, ca. 3550 kgs, accessoires Renishaw tool prove, 4th axis TRIAG with clampings, Software updated, flat screen, radio data transfer installed, tool holders, manuals Lhedeqagugopfx Aiieh

Condition: ready for operation (used), Year of construction: 1992, operating hours: 10,643 h, functionality: fully functional, travel distance X-axis: 1,500 mm, travel distance Y-axis: 815 mm, travel distance Z-axis: 815 mm, rotational speed (max.): 3,600 rpm, controller model: Heidenhain iTNC 530, A retrofit of the machine was carried out in 2010! TECHNICAL DETAILS Travel range X-axis: 1,500 mm Travel range Y-axis: 815 mm Travel range Z-axis: 815 mm Clamping table: 3,250 x 815 mm Table load capacity: 5,000 kg Quill stroke: 150 mm Spindle: SK 50 Speed range: 40–3,600 rpm MACHINE DETAILS Control: Heidenhain iTNC 530 Milling heads: Usable as single, double, triple, or quadruple head Total power requirement: 44 kW Dimensions & Weight Required space: approx. 8 x 4 x 4.5 m Transport dimensions base unit: approx. 6 x 3 x 3.5 m Control cabinet: approx. 2.6 x 0.6 x 2.6 m Lsdpjyrdxtsfx Aiishh Machine weight: approx. 20 t Operating Hours Control operating hours: 20,987 h Machine operating hours: 19,703 h Program run time: 10,643 h EQUIPMENT Hydraulics Various sheet metal parts

Condition: used, Year of construction: 1986, x-travel 2400 mm Lodpfjyqwb Sox Aiijhh y-travel 2000 mm z-travel 1450 mm table surface area 5000 x 1400 mm spindle taper SK 50 Control Fidia C1 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Year of construction: 2008, x-travel 1035 mm y-travel 560 mm z-travel 510 mm Control Heidenhain type iTNC 530 Lhjdpfoyqvh Rox Aiish table surface area 1400x650 mm workpiece weight 1000 kg Tool changer . spindle taper ISO SK40 Spindle capacity 10 KW turning speeds 8000 U/min total power requirement 20 kVA weight of the machine ca. . t dimensions of the machine ca. . m Serial number: 15425033554 Chip conveyor 2 hydraulic vises Operating hours: 53005 Spindle hours: 12233 The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: good (used), 1 used, well-maintained vertical milling head with large overhang, previously installed on a PAMA (Origin Italy) boring mill. Spindle taper: SK 50 Overhang: 660 mm Flange dimensions: 465 x 440 mm Internal bore: 294 mm Speed range: up to approx. 1,500 rpm Max. drive power: approx. 22 kW Dimensions (L x W x H): 750 x 440 x 465 mm Weight: 240 kg Accessories / Special features: • 1 rotatable axis (left/right) • Continuously adjustable angle, manual • 4 fixed indexing points at 90° each with locating pins Lsdpfx Aijyc Nhhjishh • Tool clamping with drawbar • Suitable for retrofitting to conventional, NC or CNC milling machines or boring mills of any kind, swivels left/right, manual tool clamping, ... Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: used, OTO MILLS Vertical accumulator FLOOP FR321 The FLOOP OTO FR321 is a vertical strip accumulator designed to ensure a continuous and stable strip feeding process in welded tube mills and roll-forming lines. Its system allows the accumulator to be filled both while the line is running and while it is stopped, significantly reducing coil change time. It is a robust and reliable solution for high-speed production environments. Technical specifications Manufacturer: OTO MILLS Lhodpeyl Un Ssfx Aiioh Model: OTO FR 321 Strip thickness: 1.0 – 4.0 mm Strip width: 38 – 325 mm Yield strength: 270 – 400 N/mm² Maximum line speed: 160 m/min Maximum loading speed: 500 m/min Accumulation capacity (depending on thickness): up to 600 m Maximum strip elongation: 15 % Pinch-roll drive power: 75 kW Scope of Supply Complete OTO MILLS FLOOP FR321 vertical accumulator Existing mechanical spare parts Set of spare parts for conversion to AC drive (currently operating on DC) Strip thickness: 1.0 – 4.0 mm Strip width: 38 – 325 mm Yield strength: 270 – 400 N/mm² Maximum line speed: 160 m/min Maximum loading speed: 500 m/min Accumulation capacity (depending on thickness): Up to 600 m Maximum strip elongation: 15 % Pinch-roll drive power: 75 kW

Condition: used, Year of construction: 2011, x-travel 1100 mm Lhjdpfoyk Ifhox Aiieh y-travel 610 mm z-travel 610 mm control Heidenhain 530 weight of the machine ca. 7800 kg

Condition: used, Year of construction: 1989, x-travel 650 mm y-travel 410 mm z-travel 450 mm Lhedpfsx U A Rnox Aiioh travel x vor 1000 mm control mc4va

Year of construction: 1987, condition: ready for operation (used), Offered is a Deckel FP4NC vertical milling machine with Heidenhain TNC 355 control. Year 1987, including tool cabinet as well as various tools. Travel distances: X/Y/Z: 560mm/500mm/410mm, dimensions X/Y/Z: approx. 1800mm/1600mm/2000mm, weight: approx. 2400kg. Viewing is possible by appointment. Lhedoxyk Upepfx Aiieh

Condition: ready for operation (used), Year of construction: 2019, X-travel: 600mm, y-travel: 500mm, z-travel: 540mm, max. distance-table: 690mm, feed: 40m/min, table dimensions: 700x500mm, max. workpiece weight: 800kg, controls: Heidenhain TNC 620, connected load: 18kVA, length: 2240mm, width: 3338mm, height: 2803mm, weight: 5.6t, with documentation, has not run much. Lhodpov Hndfofx Aiieh

Condition: good (used), Manufacturer: WMW VEB Type: FW 200×630 x-y-z travel: 380 – 140 – 230 mm Table size: 200x630mm Lhodpfx Aijik Hcuoijh

Condition: used, Vertical milling head, milling head, angle milling head MAHO suitable for MH300 or MH400. Year of manufacture approx. 1990. Tool holder: SK 40. Quill stroke: 60 mm. Centering diameter on the flange plate: 102 mm. Outer diameter of flange: 180 mm. Bolt circle on flange plate: Ø 150 mm. Mounting holes on flange plate: 4x Ø 11 mm. - Quill feed: 0.015 / 0.03 / 0.06 / 0.12 mm/rev. - Head drive via shaft Ø 32 with 10 mm keyway. - Knurled wheel with scale for quill stroke. - Angle scale on angle milling head 2x 90°. Dimensions L x W x H: 300 x 280 x 300 mm. Total weight: 31.4 kg. In good condition. Lhjdjxf Ur Nepfx Aiieh

Condition: new, Year of construction: 2022, Bavelloni VDM1636 series vertical milling and drilling machine. + additional options : - pre-setting of drill bits , whetting , - Barcode reader , Lsdjtui R Djpfx Aiiohh - additional Camnay office software. VDM 1636 CN is an NC vertical milling and drilling machine designed to automatically perform complex drilling and milling cycles. Equipped with one double drilling head (1 + 1 opposite spindles), each equipped with a rotary storage tool (8 positions each). The machine, characterized by great ease of operation, has been designed in accordance with the most advanced technical solutions to ensure extremely high accuracy in work. The dual rotary tool storage with 8 positions allows drilling, countersinking and milling at a single workstation. Easy to use, fast and precise in execution thanks to the technological solutions used: 5.5 kW spindles, spindle movements with ball guides, latest generation NC brushless motors with easy and intuitive software Possible work In one automatic cycle, the VDM 1636 CN can process the following operations: - Drilling - Countersinking - Milling - Cutting out Holes can be made at any point on the glass surface. The new control console used in the VDM1636 milling and drilling machine combines all the advantages of numerical control. This interface can work in a network with other machines . It can also be connected to the BAVELLONI network, so that the manufacturer's remote service is possible. The main features of this system are: - Programming while the program controls the movements of the machine, the operator can easily work on the computer. - Simple and direct graphical interface. - Data transfer via commercially available tools . VDM 1636 CN is equipped with one of the most advanced software systems (CAD / CAM) specifically designed for glass processing by numerically controlled machining centers is unique in performance, reliability and ease of use, thanks to the use of state-of-the-art technical solutions

Condition: repair required (used), functionality: not functional, Vertical milling machine Lhjdpfx Aioumlvuoieh