Used Stamping for sale (484)

Year of construction: 2025, condition: new, Dimensions (L/W/H) 0x0x0 mm Weight 90 kg Total power requirement 0 kw Djdpfx Akevz Hvvscecg

Year of construction: 2025, condition: new, Dimensions (L/W/H) 0x0x0 mm Weight 90 kg Dcjdpfx Akjvz Hvpsceg Total power requirement 0 kw

Year of construction: 2025, condition: new, Dimensions (L/W/H) 0x0x0 mm Weight 90 kg Dcsdpfx Akovz Hviocog Total power requirement 0 kw

Year of construction: 1993, condition: used, machine/vehicle number: 24323, For corner joints transom and mullion for optional glue or nail holes Water drainage slots in frame and transom profiles recesses for SCHUeCO window handles Punching out of the locking bar groove on window sash profiles opening inwards and for opening window profiles punching force depending on air pressure (6 - 8 bar): 0,6 - 0,8 MPa Air consumption: 9 l/stroke Djdjbnnwqjpfx Akcscg Space requirement: 620 x 380 x 1250 mm Weight: approx. 106 kg

Condition: used, machine/vehicle number: 4 06A1 0214/26236, For corner joints transom and mullion for optional glue or nail holes Water drainage slots in frame and transom profiles recesses for SCHUeCO window handles Punching out of the locking bar groove on window sash profiles opening inwards and for opening window profiles Dcjdebnnwfjpfx Akceg punching force depending on air pressure (6 - 8 bar): 0,6 - 0,8 MPa Air consumption: 9 l/stroke Space requirement: 620 x 380 x 1250 mm Weight: 108 kg

Year of construction: 2001, condition: used, machine/vehicle number: 15026, Format: 720 x 1040 mm Dcedpfx Akjwabbvocog The machine is a foil hot stamping machine, e.g., for holograms. It consists of a feeder, printing unit, and delivery unit (see photos). A total of 70 machines were built. The machine is currently fully functional with the new control system. The estimated cost to bring it into operation is approximately €150,000-200,000 (dismantling, transport, assembly, commissioning, training, documentation for the new control system).

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, equipped with: 1 slide feeding system right hand side 1 eccentricpress 250 kN 4 standard slide units 1 narrow slide units 1 cam shaft working range: Dsdpfx Aetzlzaekcscg wire diameter range: 0,5 - 5,0 mm stripmetal width: max. 40 mm feeding length: up to 320 mm outout: up to 135/min

Condition: excellent (used), Year of construction: 1974, functionality: fully functional, equipped with: 1 pce. gripper feeder system right hand side 1 pce. Eccentricpress 70 kN 4 pcs. Standard slide units 1 pcs. Narrow slide unit Dodjyn Rg Aopfx Akcecg 1 pce. Camshaft working range: wire diameter range: 0,5 - 3,5 mm strip metal width: up to 32 mm feeding length: up to 170 mm output: up to 250/min.

Condition: excellent (used), Year of construction: 1967, Equippment: 1 Grip feeder system right hand side 1 Eccentricpress 90 kN 2 Narrow slide units 3 Standard slide units Working range: wire diameter range: 0,5 - 3,5 mm strip metal width: max. 32 mm feeding length: max. 170 mm output: max 250/min Dedpfx Ael D N Hvskcscg

Condition: excellent (used), Offer consisting of: PZ-82 (57x82 cm), hot foil stamping cylinder in exceptional condition, immediately available, test possible. Dcedjynuudjpfx Akcog

Year of construction: 2000, condition: good (used), Used Amada Tp150ex 150ton press / stamping machine Amada TP150 EX electric Power Press with feed Atkin Bhp feed and Atkin BHP decoiler Dcodpfxon Smg To Akcsg New/year 2000 TP150 Model Amada TP-150EX Weight 16 tons Accessories Sick Guards Hydraulic Overload Variable Speed Drive Hydraulic Tool Clamping Capacity 15o tons Supplied New July 2000 Stroke 175mm Bed Area 1250 x 750 x 160mm Ram Area 700 x 550mm Ram Adjustment 100mm (motorised) Die Height 390mm Ideal for automotive or aerospace sheet metal press work New c and h frame presses also available.

Condition: like new (used), Year of construction: 2025, CARLO SALVI 476 SV revised to new 4,76x45 mm. 450 ppm - New electrical system according to CE standards with inverter and PLC - New Lubrication System - New engine with disc, pulley and brake - New thread take-up roller pump - New belts - Rectification of all parts of the Central - Pins, Bushings and Nuts replacement - New bearings Dcodpfx Ash N Di Dokcog Available in CALOLZIOCORTE (LC) c/o HBR srl. HBR will provide to the total revision.

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Dododzqltspfx Akcecg Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Dcjdpeu Rwa Ijfx Akcjg Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc Dcjdpji A A Tbefx Akcjg - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Machine. No. 52A / 63 Year of construction 1963 Pressure capacity 63 ton. Dcsdjlb I Dzopfx Akcsg throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch - Electric lift release via foot switch - Wheel reduction gear - Overload protection by breaker plate - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition

Condition: refurbished (used), Year of construction: 1988, CARLO SALVI 635 SV refurbished acc. CE Standards 6,35x70 mm. 360 ppm Available with RF system to produce semitubular parts. - New electrical system according to CE standards with inverter and PLC - New Lubrication System - New engine with disc, pulley and brake - New thread take-up roller pump Dsdpfoh N Dh Ajx Akcjcg - New belts - Rectification of all parts of the Central - Pins, Bushings and Nuts replacement - New bearings Available in CALOLZIOCORTE (LC) c/o HBR srl HBR will provide at total revision.

Year of construction: 2000, condition: good (used), Platen-type equipment designed for die cutting, creasing, and perforating cardboard and corrugated board. Maximum sheet size: 720 × 520 mm. Output: up to 25–28 cycles per minute. Motor power: 2.2 kW. Weight: approx. 2000 kg Dcjdoyb Tc Hspfx Akcjg No documentation available.

Condition: used, Year of construction: 2001, functionality: fully functional, Technical Specifications Press capacity: 800 kN (80 tons) Stroke rate: 60 – 320 strokes per minute (SPM) Stroke adjustment: 8 – 80 mm Ram adjustment (shut height adjustment): 80 mm Table size: 830 × 700 mm Bolster plate thickness: 80 mm Table opening: 500 × 200 mm Strip feed height over table: 120 mm Ram area: 500 × 400 mm Ram bore: Ø 50 × 90 mm Ram centering bore tolerance: 30 H7 mm Precision guided ram, multi-roller guidance system. Main motor power: 23 kW Drive system: Flywheel drive with planetary gearbox and pneumatic clutch/brake combination. Machine weight: approx. 8000 kg Gripper Feed Schaal SZV 3: Feed length: 4 – 150 mm Dsdpfx Aeyidnyskcjcg Strip width: 10 – 270 mm Strip thickness: 0.1 – 4 mm We also have on stock Schaal SEP 80 with SWV3E 300 mm wide Servo Feeder. Unidor Control, Machine and Operator Safety. Full Technical Documentation in German including Parts list and Technical drawings.

Year of construction: 2025, condition: new, Dimensions (L/W/H) 0x0x0 mm Weight 35 kg Dcsdjvz Hvcopfx Akcjg Total power requirement 0 kw

Year of construction: 2025, condition: new, Dimensions (L/W/H) 0x0x0 mm Weight 35 kg Dcsdpfjvz Hu Ssx Akceg Total power requirement 0 kw

Condition: used, Heißfolienprägemaschine / Hot Foil Stamping Gierlich P 4000 Dodsv R S Uiopfx Akcjcg Baujahr / Year 1989 - Serial-No. 8296 Druckleistung / Pressure max. 4000Kg Prägefläche / Embossing size max. 220 x 300mm Höhenverstellung / Height adjustment 50mm Sehr guter Zustand / Very good condition Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: used, Heißfolienprägemaschine / Hot Foil Stamping KIS MIC Junior Dodpfjv Sc Ddex Akcecg Year 1982 - Serial-No. MJ1282520 Prgefläche / Hot Foil Stamping area max. 75 x 180mm Druckleistung / Pressure max. 600Kg Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: used, Kniehebelprägepresse - Embossing Stamping Press Krause KHP Djdpfsvi Hh Iex Akcscg Prägefläche / Stamping size: 350 x 400 mm Sehr guter Zustand / Beautiful condition Online-Video-Inspection...

Condition: used, Antike Kniehebelprägepresse / Antique Embossing Hot Stamping Press Karl Krause KHP Baujahr / Year ca. 1930 - Serial-No. 48090 Prägefläche / Embossing Size max. 340 x 430mm Beheizung mit Gas / Heating with Gas Online-Video-Inspection by WhatsApp - MS Zoom - Telegram Dedewtw E Depfx Akcecg On Stock Emskirchen/Nürnberg - Available Immediately - Can be test