Used Platen for sale (601)

Condition: ready for operation (used), Year of construction: 2014, operating hours: 22,626 h, clamping force: 100 kN, screw diameter: 25 mm, Hydraulic injection moulding machine manufactured in 2014. This Arburg 470 H 1000-170 features a closing force of 100 tons and a screw diameter of 15/25 mm. It includes a selection unit and a single platen design, with a beam spacing of 470 x 470 mm. If you are looking to get high-quality injection moulding capabilities, consider the Arburg 470 H 1000-170 machine we have for sale. Contact us for further details. Ncodpfjzm S Auex Amyjw • Selection unit: yes • Single platen: yes • Beam spacing: 470 x 470 mm • Operating hours: 22,626 h • Electricals: • Operating voltage: 400 V, 3~, 50 Hz • Control voltages: 230 V, 50 Hz; 24 V~ • Motor/heating rated current: 80 / 58 A • Total rated current: 138 A • Total connected load: 75 kW • Condition note: small servo motor problem Additional equipment • Geiger handling (optional)

Condition: good (used), CMC Italia Q Finish Crater 20 Book Press Book press with groove cutter and heated platens. Manufactured by CMC, Italy. Technical specifications: Maximum format: 420 x 500 x 80 mm Weight: 420 kg Pressure: 5000 kg Built-in hydraulic unit. Automatic book feed. Automatic format detection. 380V power supply + compressed air. Nsdpfxjzmu N Ro Amyjcw

Condition: used, Year of construction: 2019, machine/vehicle number: 26488, functionality: fully functional, power: 2.2 kW (2.99 HP), input voltage: 230 V, input frequency: 50 Hz, type of input current: AC, table width: 400 mm, table length: 500 mm, overall weight: 116 kg, Equipment: CE marking, Transmatic TS 5 PA Industrial Pneumatic Heat Transfer Press (2019) Professional Swing-Away Heat Transfer Press for Hotfix Rhinestones, Decorative Stone Application & Textile Branding The Transmatic TS 5 PA is a premium industrial pneumatic heat transfer press manufactured by Transmatic S.r.l., Italy, designed for continuous, high-volume garment decoration and textile finishing. This machine was used in the former MASI JEANS factory for applying hotfix rhinestones, decorative crystals, heat-applied embellishments, logos and transfers to denim garments and fashion apparel. Its pneumatic operation provides consistent pressure across every pressing cycle, ensuring repeatable production quality while minimizing operator fatigue. The machine is supplied as a complete professional workstation and includes interchangeable lower platens, allowing fast changeovers for different garment sizes and applications. Technical Specifications Manufacturer: Transmatic S.r.l. (Italy) Model: TS 5 PA Serial Number: 26488 Year of Manufacture: 2019 Voltage: 230 V Power: 2.2 kW Operation: Pneumatic (external compressed air required) Control System: Digital colour touchscreen Heating Control: Electronic temperature and time control Pressure Adjustment: Integrated pneumatic regulator with pressure gauge Safety: Emergency stop button and CE certified Included Equipment • Complete Transmatic TS 5 PA heat transfer press • Digital touchscreen control system • Standard lower platen • Additional interchangeable small platen for sleeves, pockets, labels and small logos • Integrated pneumatic pressure regulator • Work light • Complete workstation Key Features • Premium Italian industrial quality Ncjdpfxezn U A Ho Amyew • Designed for continuous production environments • Previously used for applying hotfix rhinestones and decorative stones to denim garments • Pneumatic automatic closing system for perfectly repeatable pressure • Swing-away upper platen for safe, ergonomic operation • Digital touchscreen with programmable temperature, pressing time and production counter • Exceptionally low recorded usage of only 1,498 pressing cycles • Fast changeover using interchangeable lower platens • Heavy-duty industrial construction for long service life • Excellent choice for garment manufacturers, decorators and textile finishing companies Typical Applications • Hotfix rhinestone application • Crystal and decorative stone application • Fashion garment embellishment • Denim decoration • Heat transfer printing • DTF transfers • Vinyl heat transfers • Logo application • Patch attachment • Label application • Sportswear production • Workwear branding • Promotional apparel • Textile finishing Condition Previously used in professional garment manufacturing. The machine powered a dedicated production process for garment decoration until the closure of the MASI JEANS factory. The digital touchscreen controller powers on and operates normally, and the production counter displays only 1,498 completed cycles. Overall cosmetic condition is very good with only minor signs of normal industrial use. Inspection is welcome prior to purchase. Location Valga, Estonia Dismantling & Transport Buyer is responsible for dismantling, loading and transportation. Sales Terms Sold as-is, where-is, without warranty. Part of the MASI JEANS factory liquidation.

Condition: excellent (used), Year of construction: 2020, 2020 Boy 60E Injection Molding Machine Type 445 With Procan Alpha 4 Control & Apex Dynamics SH650 Unloading Robot & Conveyor Ncsdpfx Amezn N Aheyew Clamping Force 60 tons (600 kN). Distance Between Tie Bars 360 × 335mm. Platen Dimensions 570 × 530mm. Maximum Daylight Between Platen Approx 650mm. Clamping System: 4 Tiebar Cantilevered Two Platen Style. Maximum Opening Stroke (Adjustable) Approx 400mm. Minimum Mould Height Approx 250mm. Maximum Shot Volume Approx 170cm3. Maximum Mould Weight on Moveable Clamping Side Approx 400kg. S/No. 55761. S/No. 55761 (2020). With Shini Hopper. Weight of Machine Approx 2,250kg. Dimensions Approx 2,970mm x 2,010mm x 2,000mm High.

Condition: excellent (used), Year of construction: 2022, 2022 Negri Bossi M372 3300H-2100 Plastic Injection Molding Machine Platen Dimension 1,060 x 930mm. Mould Height Min/Max 220/730mm. Distance Between Tie Bars 720 x 600mm. Mould Maximum Opening Stroke 640mm. Clamping Force 330 Tonnes. Injection Unit: Shot Volume 1,190cm³, Shot Weight 1,080g. Maximum Hydraulic Pressure (Clamp) 180bar. Maximum Hydraulic Pressure (Injection) 195bar. Maximum Power 172kW. Screw Ø70mm. S/No. 372-270 (2022). With Shini Sal-330-CE Hopper Loader. Weight 12,300kg. Njdpfx Amozn Nvujyscw

Condition: excellent (used), Year of construction: 2024, 2024 Star SP-23 CNC Sliding Head Lathe With Fanuc Series Oi-TF Plus Control With FMB Turbo RS 3-38 Barfeeder Number Of Axes 7, Main Spindle (Headstock) 'Z1/C1', Main Spindle Platen 'X1/Y1, Sub Spindle 'X2/Z2/C2' Axis. Maximum Machining Ø23mm. Headstock Stroke 205mm/50mm (NGB). Maximum Main Spindle Speed 10,000rpm (3.7kW Motor). Main Spindle Tooling: Turning Tool 8 Tools at 12mm SQ, Drilling Arm Sleeve Holder Capacity 5 x Ø22MM Sleeves (ER16), Power Driven Tool Positions 2 + 5 Modular Stations. Maximum Driven Tool Speed 8,000rpm. Sub Spindle Maximum Chucking at 23mm. Maximum Main Spindle Speed 10,000rpm (2.2kW Motor). Sub Spindle Tooling: Back-Working Platen Positions 4, Maximum Drill Sleeve Capacity ER20, Power Driven Tool Positions 4 (ER16), Maximum Driven Tool Speed 8,000rpm. Barfeeder Length 4,280mm. S/No. 668 (2024). Ncodpfjzn Nm Hsx Amyjw With Coolant System, LNS Coolant System, Firetrace Fire Suppressor, Filtermist Mist Extraction Unit, Parts Conveyor, Signal Tower, Toolkit, Assorted Tooling (Collets, Connectors) . Weight 2,250kg.

Condition: good (used), Code: 0448 Brand: KOLMAG - ITALY Model: PGP 80 Hydraulic cold press for panels, furniture, doors, joinery, composite materials and various: Technical data: Platens dimensions 2500 x 1100 mm N° 4 pistons Opening 310 mm Thrust 60 ton Motor 4 Hp Overall dimensions mm 3100 x 1150 x 1780 h Nodpfx Aezmifgomyscw Weight kg 2200

Year of construction: 2015, condition: ready for operation (used), injection weight: 2,424 g, This Husky HPETL230E-RSE95D-95 was manufactured in 2015. It is an all-electric injection molding system with a maximum throughput of 390 kg/h PET and a max shot weight of 2424 g PET. The clamping unit is fully electric with a toggle drive, and it features an integrated control system for additional equipment. Consider the opportunity to buy this Husky HPETL230E-RSE95D-95 electrical injection moulding machine. Contact us for more information about this machine. Additional equipment • Mold Dehumidifier: Incl. hood, spare parts package, piping • Conveyor Belt: Two-sided preform filling system for cartons/grid boxes Machine Benefits Technical Machine Benefits • The package includes two machines along with additional components such as pellet silos, pellet feeder, discharge system for foreign bodies in pellets, dosing unit for color, and platform. Everything seen in the pictures is included. • Max throughput: 390 kg/h pet • Clamping unit: fully electric with toggle drive • Clamping platen: movable, guided on rollers • Type: split version • Dryer: dr815ht-g3 with 4000-liter drying hopper (stainless steel, insulated) • Husky 1: 3 tools - 28 gauge muzzle, 17. 8/26/30. 3 grams • Husky 2: 2 tools - 38 gauge muzzle, 18/29 grams Extra Information Clamping Force Clamping Unit: Fully electric with toggle drive Clamping Platen: Movable, guided on rollers Control Unit Control System: Integrated control system for additional equipment Display for Mold Cooling Water Temperature/Pressure (Flow and Return) Control Output for Color Dosing Unit Lubrication System: Automatic Post-mixing Device: Integrated in the nozzle Tools 48-cavity H-PET Injection Mold Preform Weight: 17.8 g and 30.26 g Punch Size: 50 x 140 mm Includes: 3-position removal plate, basic spare parts package 32-cavity H-PET Injection Mold Preform Weight: 18 g and 29 g (38 mm Bericap) Punch Size: 63.5 x 140 mm Includes: 3-position removal plate, basic spare parts package Functions Temperature Monitoring and Setting Continuous Level Meter Variable Dew Point Setting Conveying: Hot transport of the granulate via vacuum unit P07 to the booster hopper (HAD400) Paint Mixing Units For Solid Paint: Volumetric, 4 dosing screws For Liquid Paint: 4 dosing pumps Preform Production Specifications Preform Weight: 17.80 g Mouth: PCO1881 LW Length: 89.35 mm Wall Thickness: 3.06 mm Base: 2.30 mm Shape: Bell Cavities: 48 Cycle Time: 12.4 ±0.3 s Preforms per Hour: 13935 Annual Production (95% availability): 111205000 Throughput (kg/h): 248 Power Consumption: 506 Wh/kg PET Preform Weight: 29.00 g Mouth: Bericap 38 Length: 108.59 mm Wall Thickness: 3.16 mm Base: 2.42 mm Shape: Bell Ncodpfex D Hvwjx Amysw Cavities: 32 Cycle Time: 13.7 ±0.3 s Preforms per Hour: 8409 Annual Production (95% availability): 67101000 Throughput (kg/h): 244 Power Consumption: 532 Wh/kg PET Preform Weight: 18.00 g Mouth: Bericap 38 Length: 82.04 mm Wall Thickness: 2.70 mm Base: 2.20 mm Shape: Bell Cavities: 32 Cycle Time: 11.3 ±0.3 s Preforms per Hour: 10195 Annual Production (95% availability): 81353000 Throughput (kg/h): 184 Power Consumption: 506 Wh/kg PET Preform Weight: 30.26 g Mouth: PCO1881 LW Length: 122.30 mm Wall Thickness: 3.00 mm Base: 2.30 mm Shape: Grade Cavities: 48 Cycle Time: 14.7 ±0.3 s Preforms per Hour: 11755 Annual Production (95% availability): 93805000 Throughput (kg/h): 356 Husky1 PCO 1881 30,3g 1-1,5l PCO 1881 26,0g 1-1,5l PCO 1881 17,8g 1-1,5l Husky2

Year of construction: 1975, condition: ready for operation (used), An automatic Wupa flatbed die-cutting and creasing machine (auto platen) is available. Material weight range: 100-1000g/m², min. sheet size X/Y: 420mm/600mm, max. sheet size X/Y: 800mm/1120mm, max. die-cutting size X/Y: 780mm/1100mm, max. die-cutting force: 240t, max. production speed: approx. 3000sheets/h. An on-site inspection is possible. Nodpfx Aeznx I Homyscw

Condition: like new (used), Year of construction: 2020, machine/vehicle number: 218, functionality: fully functional, operating hours: 440 h, power: 11 kW (14.96 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 4 t, table width: 1,500 mm, table length: 1,000 mm, ram plate width: 1,500 mm, ram plate length: 1,000 mm, overall weight: 670 kg, Equipment: CE marking, documentation/manual, Professional Transmatic TM-150 Heat Press (150x100 cm) A high-quality, professional Transmatic TM-150 flatbed heat press. This is a heavy-duty, automatic electric heat press that is perfectly suited for printing large volumes of corporate clothing, sportswear, fashion items, and flags/banners. Thanks to the unique 1-drawer system with 3 open sides, you can also easily feed extremely long pieces of fabric or banners. Key specifications: Printing surface: Large format of 150 x 100 cm Best Heat Press 2021 Ncsdpfjznuyrjx Amyew Technology: Ideal for sublimation printing and thermal printing on textiles and laminates. Temperature control: Equipped with 3 independent thermostats for extremely accurate and consistent heat distribution across the entire platen. Operation: Digital touchscreen for precise time and temperature settings. Memory: Ability to store 4 presets. Extras: Includes daily and total piece counters, an automatic error detection system, and a blue Nomex protective mat.

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 244136, clamping force: 3,200 kN, screw diameter: 55 mm, clearance between the columns: 720 mm, displacement volume: 570 cm³, injection pressure: 2,000 bar, injection weight: 521 g, mold height (min.): 300 mm, total length: 7,460 mm, total width: 1,848 mm, total height: 2,267 mm, overall weight: 20,000 kg, For sale is an injection molding machine from the manufacturer Arburg, type 720 H 3200 - 1300, from 2018. The machine is in very good condition. Clamping force: max. 3,200 kN Mold opening force: max. 110 kN Opening stroke: max. 600 mm Mold height (variable): 300 mm to 800 mm Platen distance (variable): max. 900 mm to 1,400 mm Distance between tie bars (H x V): 720 mm × 720 mm Size of the mounting platens (H x V): 1,040 mm × 1,040 mm Max. weight of the moving mold half: 2,900 kg Ejector force | Stroke: max. 86 kN | 250 mm Screw diameter: 55 mm Effective screw length (L/D): 22 Maximum screw stroke: 240 mm Calculated stroke volume: 570 cm³ Maximum shot weight (in polystyrene/PS): 521 g Maximum injection pressure (holding pressure): 2,000 bar Maximum material throughput (PS): 86 kg/h Maximum injection flow rate: 713 cm³/s Specific injection pressure (max.): 2,000 bar Nozzle closing force | Stroke (max.): 90 kN | 550 mm Heating power / Heating zones: 22.9 kW | 8 zones 3. Connection values & machine weights Net weight of the machine (without oil): 18,550 kg Oil capacity (hydraulics): 410 liters Cooling water connection: max. 30 °C | min. 1.5 bar differential pressure (Δp) | Nominal size DN 25 Drive power (pump motor): max. 60 kW Total connection power (electrical at 400V/50Hz): 84 kW Max. current / Fuse rating: Machine total: 125 A Heater: 40 A Upon request, transport and loading can be arranged for an additional fee, throughout Europe. Ncedpjzl Tc Tefx Amyow Prices plus VAT. Inspection possible by appointment. Contact us, our team will be happy to assist you. Trade-in or exchange is possible! Machine Purchase / Sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, ETC. Gjbn N Ay Dowza Dxogoil Do you need a high-quality but affordable metalworking machine for your production? Or do you want to sell yours? For more information or contact options, please visit our website.

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, pressing force: 660 t, overall weight: 28,000 kg, heating capacity: 31 kW (42.15 HP), plate length: 1,900 mm, plate width: 1,600 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Nsdpjznmbzefx Amyecw Press force: 660 t Press plate dimensions: 1,900 × 1,600 mm Heating capacity: 31 kW MACHINE DETAILS Electrical data Operating voltage: 400 V Control voltage: 220 V Frequency: 50 Hz Phases: 3 + N + PE Rated current: 160 A Connected power: 108 kW Machine weight: approx. 28,000 kg Design: Lower platen heating press / molding press EQUIPMENT Heated press plates Documentation

Condition: excellent (used), Year of construction: 2018, SBL 1060 SE Year: 2018 Sheet size (max.): 1060 x 760 mm Sheet size (min.): 350 x 400 mm Stamping size (max.): 1045 x 745 mm Gripper margin: 11 mm Platen pressure (max.): 300 tons Production speed: 8,000 sheets/hour Total power consumption: 20 kVA Elevated machine: 400 mm Sheet feeder: Manual non-stop pile feeder Material range: Paper and board from 470 x 350 mm to 1060 x 760 mm Max. cutting format: 1050 x 740 mm Min. sheet size: 470 x 350 mm Max. sheet size: 1060 x 760 mm Max. cutting pressure: 300 tons Material thickness: 0.1 – 2 mm (corrugated/laminated max. 4 mm) Min. gripper margin: 9.5 mm Max. inside chase size: 1155 x 852 mm Cutting plate size: 1076 x 756 mm Power consumption: Total 32 kW (22 kW + 10 kW for lower plate heating) Machine dimensions (L x W x H): 5,900 x 5,700 x 2,615 mm Max. pile height – feeder (with pallet): 1,750 mm Max. pile height – delivery (with pallet): 1,450 mm - Vacuum belt on feeder - Pneumatic feeder table - Non-stop manual feeder system - Anti-static system - Pre-pile device - Manual suction group adjustment - Micrometric suction adjustment - Motorized side pile adjustment - 2 pneumatic side register guides - Electronic control of front and side register Cutting/Embossing Section - Automatic pressure adjustment up to 300 tons - Preparation and introduction table for die frames in platen - Quick-lock die chase frames with bottom plate Ncjdpfxeznlbaj Amyjw - Pneumatic locking of the chase and lower supporting plate - Centerline system - Micrometric system - Stripping - Quick lock for upper and central stripper frames - Double accessory kit for lower stripper prep (pins, bars, clamps, etc.) - Delivery Section - High-pile automatic non-stop delivery with conveyor - Sheet deceleration device - Tab insertion device

Condition: ready for operation (used), Year of construction: 2006, clamping force: 5,750 kN, screw diameter: 80 mm, injection weight: 1,304 g, Hydraulic injection moulding machine manufactured in 2006. This Krauss Maffei KM 575-2700 C2 features a clamping force of 575 t and a screw diameter of 80 mm. It offers a maximum platen stroke of 1750 mm and a minimum mold height of 600 mm. If you are looking to get high-quality injection moulding capabilities, consider the Krauss Maffei KM 575-2700 C2 machine we have for sale. Contact us for further details. • Injection pressure: 1829 bar • Platen dimensions: 1620 x 1470 mm • Tie-bar spacing: 1000 x 880 mm • Max. platen stroke: 1750 mm • Min. mold height: 600 mm • Centering ring: 200 mm • Ejector pin length: 550 mm • Ejector pin internal thread: M16 • Core pulls: 3 • Air blow: 2 • Hydraulically operated nozzles: No • Pneumatically operated nozzles: No • Number of hot runners: 12 • Max. injection volume: 1433 ccm • Sorting flap: No Additional equipment Ncodpfxezlynpe Amyew • Conveyor • Manipulator / Robot

Condition: like new (used), Year of construction: 2019, operating hours: 399 h, functionality: fully functional, clamping force: 2,200 kN, screw diameter: 48 mm, clearance between the columns: 650 mm, displacement volume: 318 cm³, injection pressure: 1,900 bar, mold height (min.): 250 mm, ejector force: 35,000 N, ejector stroke: 150 mm, opening stroke: 550 mm, plate length: 900 mm, plate width: 900 mm, total height: 2,800 mm, overall weight: 10,700 kg, Equipment: documentation/manual, FANUC ROBOSHOT Alpha S-220iA – fully electric injection moulding machine, year 2019 Very lightly used precision injection moulding machine with only 399 operating hours. The FANUC ROBOSHOT Alpha S-220iA combines high repeatability, dynamic movements and energy-efficient production. Suitable for demanding technical plastic parts and reliable series production. Technical data: - Clamping force: 2,200 kN (220 t) - Double-toggle clamping mechanism - Tie-bar spacing: 650 × 650 mm - Platen size: 900 × 900 mm Nedpfx Amsznd Dysyocw - Mould height: 250–750 mm, extended version - Clamping stroke: 550 mm - Ejector stroke: 150 mm - Maximum ejector force: 35 kN - Screw diameter: 48 mm - Shot volume: 318 cm³ - Maximum injection speed: 200 mm/s - Maximum injection pressure: 1,900 bar - Locating ring: Ø 160 mm - Fully electric drive Control and equipment: - FANUC 31i-B CNC control - 15-inch LCD touchscreen - AI mould and ejector protection - Precision metering and pressure-profile functions - Automatic mould-height adjustment - Energy-consumption measurement - Euromap 67 robot interface - Three independent air valves - Cascade control for up to eight valves - USB and memory-card output - Four-circuit flow meter The machine is in like-new condition and fully operational. Inspection is available by appointment. Price, delivery time and further information are available on request.

Condition: ready for operation (used), Year of construction: 2003, clamping force: 2,750 kN, screw diameter: 60 mm, injection weight: 547 g, Hydraulic injection moulding machine manufactured in 2003. This Engel ES 1050/275 HL-V features a clamping force of 275 t and a maximum platen stroke of 1200 mm. It has a screw diameter of 60 mm and a maximum injection volume of 607 ccm. If you are looking to get high-quality injection moulding capabilities, consider the Engel ES 1050/275 HL-V machine we have for sale. Contact us for further details regarding this machine. • Screw diameter: 60 mm • Injection pressure: 1725 bar • Platen dimensions: 1050 x 650 (900) mm • Tie-bar spacing: Tie-bar-less (nemá) • Max. platen stroke: 1200 mm Ncedpfx Aozlrvxsmyow • Min. mold height: 350 mm • Centering ring: 160 mm • Ejector pin length: 330 mm • Ejector pin internal thread: M16 • Core pulls: 2 • Air blow: 1 • Hydraulically operated nozzles: No • Pneumatically operated nozzles: No • Number of hot runners: 8 • Max. injection volume: 607 ccm • Working hours: 60,701.3 h

Condition: ready for operation (used), Year of construction: 2006, clamping force: 3,500 kN, screw diameter: 60 mm, injection weight: 700 g, Hydraulic injection moulding machine manufactured in 2006. This Krauss Maffei KM 350-1900 C2 features a clamping force of 350 t and a screw diameter of 60 mm. It offers a maximum platen stroke of 1600 mm and a platen size of 1060 x 1095 mm. If you are looking to get high-quality injection moulding capabilities, consider the Krauss Maffei KM 350-1900 C2 machine we have for sale. Contact us for further details. • Injection pressure: 2420 bar • Platen dimensions: 1060 x 1095 mm • Tie-bar spacing: 800 x 710 mm • Max. platen stroke: 1600 mm • Min. mold height: 680 mm • Centering ring: 160 mm • Ejector pin length: 400 mm • Ejector pin internal thread: M16 • Core pulls: 3 • Air blow: 2 • Hydraulically operated nozzles: 1 • Pneumatically operated nozzles: 1 • Number of hot runners: 10 • Max. injection volume: 769 ccm Nsdpfx Aszlrkvsmyjcw Additional equipment • Conveyor • Manipulator / Robot

Year of construction: 2017, condition: ready for operation (used), Used door panel production - consisting of: Double-End Profiler Brand: Kraft Technical Specifications - 2 scissor lift tables - 2 vacuum grippers - Feed roller conveyor with belt conveyor - New Siemens touch control system 13 roller conveyor sections Brand: Kraft Technical Specifications - Powered, approx. 3000 mm each Continuous Inlay Special inlay line Gantry loader Brand: Kraft Year of manufacture: 2023 Technical specifications - For separating, aligning, and placing HPL Glue applicator Brand: Bürkle Year of manufacture: 1990 Glue applicator Brand: Kuper Year of manufacture: 2018 Laying table Technical data - Work platform for glue tanks, including staircase - Lifting station - motor-driven - Includes PVC conveyor belt Continuous-feed platen press Brand: Bürkle Optima 1428/50 Year of manufacture: 2017 Technical data - Start of series production in 2023 - 2 x 4 levels with a pressing area of 1400 x 2800 mm - With automatic feeder (manufacturer: Bürkle) - Removal device (manufacturer: Bürkle) Hedgehog buffer Technical specifications - For temporary buffering of semi-finished door panels - Total length approx. 14,000 mm - Solid steel construction - Approx. 200 individual compartments Storage and transport system Brand: Kraft Technical data - Powered storage and transport roller conveyor - Roller width 1000 mm - Total length approx. 120 running meters 3 automatic cross-transfer carriages Brand: Kraft Year of manufacture: 2018 Technical data Nsdpfx Amsy Dutmeyecw - Roller width approx. 1400 mm - Transfer length: 2900 mm Horizontal shredder Brand: Reinboldt Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding. • Offer: Used door leaf production line • Main machine: Continuous-action stack press • Technical specifications: • 2 x 4 tiers • Pressing area: 1400 x 2800 mm Additional equipment • Automatic Bürkle feeding system (for the press) • Bürkle removal device (for the press) • Panel rack • Manufacturer: Robering • Model: Dexion P90 Plus • Year of manufacture: 2021 • Technical specifications: • 8 uprights • Height: approx. 6000 mm • Max. permissible shelf load: 3000 kg • 2x Tilting hoppers • Manufacturer: Bauer • Model: WU-R1500 • Year of manufacture: 1998 • Technical specifications: • Capacity: 1.5 m³ • Hedgehog buffer • Technical specifications: • Solid steel construction • Approx. 200 individual compartments • KRAFT storage and transport system • Roller conveyor: • Roller width: 1000 mm • Total length: approx. 120 running meters • 3 automatic cross-transfer carriages (built in 2018): • Roller width: approx. 1400 mm • Transfer length: approx. 2900 mm

Year of construction: 2001, operating hours: 27,400 h, condition: good (used), functionality: fully functional, Die-cutting machine with stripping station, foundation tilting table (third-party manufacturer), tilting table/preparation table, waste stripper, electronic double-sheet detection, pull marks BS + AS, machine height increased by 300 mm, 1 die-cutting frame, various stripping frames and stripping pins (including cart), quick centering device for sheet stacks, manual non-stop feed, manual non-stop delivery, price ex works, dismantling and loading can be arranged for an additional charge! Video available upon request! In May 2026, a PLATEN CONDITIONING was carried out by BOBST on the die-cutting machine. All deposits were removed from the upper and lower tables, and the die was polished. The sector was opened and assessed as being in "like-new" condition. Photos, video, or invoice available upon request! Note: The platform must be adapted by the buyer! Longitudinal handrail missing! Ncodpfxezmyfdo Amysw Technical main data: Maximum sheet size: 720 × 1020 mm, Minimum sheet size: 350 × 400 mm, Maximum die-cutting force: 250 tons (2.5 MN), Maximum production speed: 7,500 sheets per hour, Processable materials: Paper / solid board: from 80 g/m² up to 2000 g/m², corrugated board: up to 4.0 mm thick Dimensions and weight: Machine length: approx. 6,000 mm Machine width: approx. 2,000 mm Machine height: approx. 2,500 mm Total weight: approx. 19,500 kg Features of the Series II: C.U.B.E. system: Electronic Bobst machine control system Centerline system: Micrometric adjustment for fast set-up times and precise tool alignment Stripping station: Integrated double-round stripping unit for waste removal Non-stop system: Continuous sheet feeding and delivery Ultrasonic double-sheet detection

Condition: excellent (used), Year of construction: 2004, Boy 90 M Year of manufacture: 2004 Injection unit: Screw diameter: 42 mm Injection weight: 193 g Injection pressure: 1724 bar Metering volume: 214.7 ccm Clamping unit : clamping force: 90 t tie bar distance: 430x360 mm size of clamping platens: 635x610 mm ejector: hydraulic clamping unit: hydraulic Control: Procan - touch screen Additional equipment: Euromap 12 Robot interface Air valve x 1 Dimensions: Weight: 3100 kg Length/width/height: 4.37x1.21x2.20 m Ncsdpfjzc I U Tex Amyow Drive: Pumps/motor: 15 kW Heating power: 11,3 kW Total power: 26,3 kW All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request

Condition: excellent (used), Year of construction: 2016, Boy 55A Pro / Operating hours: 18,153 in automatic mode / Machine in very good technical condition. Year of manufacture: 2016 Injection unit: Screw diameter: 38 mm Injection weight: 123.9 g Injection pressure: 1508 bar Metering volume: 136.1 ccm Clamping unit: Clamping force: 55 t tie bar distance: 360x335 mm size of clamping platens: 665x600 mm ejector: hydraulic clamping unit: hydraulic Control system: Procan Alpha - touch screen Additional equipment: Machine in very good technical condition Operating hours: 18.153 in automatic mode Nsdezc Naqopfx Amyocw Pneumatic core x 2 injection unit hardened - bimetal The machine has been regularly serviced by the authorized service boy in France It is possible to change the screw diameter for fi 32 mm or 42 mm Dimensions: Weight: 2430 kg Length/width/height: 3.25x1.14x2.02 m Drive: Pumps/motor: 11 kW Heating power: 7,7 kW Total power: 18,7 kW All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request

Condition: excellent (used), Year of construction: 2001, Arburg 320C 600-250 / machine in very good technical condition Year of manufacture: 2001 injection unit: Screw diameter: 35 mm injection weight: 121 g Injection pressure: 1820 bar Metering volume: 144 ccm Clamping unit: clamping force: 60 t Nedpfxszc Nl Tj Amyocw tie bar distance: 320x320 mm size of clamping platens: 446x446 mm ejector: hydraulic clamping unit: hydraulic Control system: SELOGICA Additional equipment: Very good technical condition Machine has produced molded parts for medical industry - pure production conditions Core pull control Injection unit hardened - bimetal Built-in sorting flap Dimensions: Weight: 2330 kg Length/width/height: 3.65x1.48x1.99 m Drive: Pumps/motor: 15 kW Heating power: 6,5 kW Total power: 21,5 kW All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request

Condition: excellent (used), Year of construction: 2017, Arburg 370E 600-170 with Arburg Multilift Select robot / All-electric injection molding machine Year of manufacture: 11.2017 Injection unit: Screw diameter: 30 mm Shot weight: 77 g Injection pressure: 2000 bar Dosage volume: 85 ccm Clamping unit: Clamping force: 60 t Tie bar spacing: 370x370 mm Platen size: 510x510 mm Ejector: electric Clamping system: toggle Control system: SELOGICA - touchscreen Additional equipment: Production line with Arburg Multilift Select robot and conveyor belt All-electric machine: high-speed, energy-efficient, and very quiet Operating hours: h in automatic mode Euromap 67 Robot interface Air valve x 2 Hydraulic core pull x 1 Hot runner control x 24 zones Hardened injection unit – bimetallic Main motor: servo-driven with inverter for energy saving Injection unit driven by servo motor controlled by inverter Parallel movements Central lubrication Machine with two cylinders / nitrogen accumulator (extra charge for high-speed operation) Integrated Arburg conveyor belt and sorting flap Arburg Multilift Select robot, 6 kg, transverse Year of manufacture: 11.2017 Ncjdpfx Amozc Nm Roysw 4-axis robot: 3 axes servo-driven (electric), C axis pneumatically driven Stroke (axes): X-600, Y-800, Z-1800 mm Robot safety package Robot with adapter and safety housing Purchase of robot and conveyor belt possible at additional cost Dimensions: Weight: 3600 kg Length/width/height: 4.00x1.45x2.04 m All offered machines are started up by our service technicians before sale. A video of the technical tests of the selected machine can be provided, or you can participate in live technical demonstrations at our facility in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2004, Arburg 420C 800-250 Year of manufacture: 2004 Injection unit: Screw diameter: 30 mm Shot weight: 89 g Injection pressure: 2470 bar Nedpszc Nq Ajfx Amyecw Dosage volume: 106 ccm Clamping unit: Clamping force: 80 t Tie bar spacing: 420x420 mm Platen size: 570x570 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA Additional equipment: Euromap 67 Robot interface Hydraulic core pull x 1 Injection unit hardened – bimetallic Dimensions: Weight: 3180 kg Length/Width/Height: 4.30x1.64x2.08 m Drive: Pump/motor: 15 kW Heating capacity: 6.5 kW Total power: 21.5 kW All machines offered are started up by our service engineers before sale. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical demonstrations at our facility in Łódź. Price: On request

Condition: excellent (used), Year of construction: 1998, Ferromatik Milacron K110D-S/2F / 2K injection molding machine Year of construction: 1998 Nodpfx Aozc Nrmsmyocw Injection unit: Screw diameter: 30 mm Injection weight: approx. 85 g Injection pressure: 2298 bar Dosing volume: 99 ccm Clamping unit: Clamping force: 110 t Distance between tie bars: 470x470 mm Size of the clamping platens: 740x740 mm Ejector: hydraulic Clamping unit: hydraulic Control system: Ferromatik Milacron Additional equipment: 2-component injection molding machine Euromap 67 Robot interface Hydraulic core pull x 4 Control system with hot runners Injection unit is wear-resistant and resistant to corrosion Screw diameter in the vertical injection unit: ⌀25 mm - approx. 43 g/hp The machine has been regularly serviced The service center recently replaced the machine's cylinder with screw and the hydraulic valves with new ones Dimensions: Weight: 6300 kg Length/width/height: 5.00x1.60x3.60 m All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request