Used Plastic Injection Molding Machine for sale (68,581)

Condition: used, Injection molding machine ARBURG, Type Allrounder 320 C 600-100 Serial No. 189356, Year of manufacture 09/2002 Clamping force 60 tons Screw diameter 25 mm Dosing volume max. 49 cm3 Injection pressure max. 1570 bar Opening stroke - platen stroke max. 350 mm Lodpfx Aezqglrjpmohk Platen dimensions 446 x 446 mm Tie bar spacing 320 x 320 mm Mold height min.: 200 mm Platen spacing min.: 200 mm Platen spacing max.: 550 mm Centering of fixed and moving platens 125 mm Heater power 4.9 kW Motor power hydraulic pump 15 kW Mains connection 400 Volt, 50 Hz, 19.9 kW - Machine control SELOGICA - Two controllable hydraulic circuits for core pullers - Injection unit with COLORTRONIC material hopper for automated granule feed - U-version interface - HHG interface - Control ARBURG MULTRONICA with foil keypad and integrated display - 88790 operating hours recorded (power-on hours) - 44925 operating hours of the hydraulic pump (hydraulic on) - Control cabinet fixed to the machine - Work area protective doors at the front and rear, manually sliding with safety switches - Mobile control panel with function keys, mounted on the back of the machine Space requirement L x W 3650 x 1700 mm Height with material hopper 2200 mm Weight 3000 kg Good condition

Condition: excellent (used), Year of construction: 2021, operating hours: 3,300 h, functionality: fully functional, machine/vehicle number: ADKL2001, clamping force: 14,000 kN, screw diameter: 120 mm, clearance between the columns: 1,450 mm, column diameter: 240 mm, displacement volume: 7,351 cm³, injection pressure: 1,200 bar, injection weight: 6,983 g, mold height (min.): 650 mm, ejector force: 350,000 N, ejector stroke: 380 mm, opening stroke: 1,450 mm, plate length: 2,950 mm, plate width: 2,000 mm, plate height: 2,000 mm, total length: 14,100 mm, total width: 3,400 mm, total height: 3,600 mm, overall weight: 75,000 kg, heating capacity: 60 kW (81.58 HP), pressure: 178 bar, number of injections: 1, pump power: 204,000 W, power: 266 kW (361.66 HP), type of input current: three-phase, input frequency: 50 Hz, input voltage: 400 V, input current: 520 A, Equipment: documentation/manual, The machine has seen limited use and is in very good condition. It has been well maintained. The machine only processes ABS and PP. It features a Beckhoff control system. The machine is equipped with extensive additional equipment, including 3 pneumatic valves, two hydraulic valves, a servo valve for table movement hydraulics, 32 tool heating zones, a water manifold with 8 zones, a screw heating element insulation, a hydraulic screw rotation system for torpedo replacement, a torpedo with a locking system, an interchangeable centering ring, a Euro-map for the robot, a door with automatic opening via an electric motor, and an electrical cabinet with sockets. Additionally, water blocks are installed on both the moving and stationary tables, each with 8 connections. Furthermore, a set of spare parts is included, such as a complete torpedo, a screw nozzle, heaters, temperature probes, and specific hydraulic seals, as well as a self-filtration filter and a torpedo wrench, and auxiliary ejector rods. A Wemo robot can also be sold with the machine; while it is not the subject of this advertisement, it can be purchased separately and added to the machine. It was used with the machine and is adapted for it. Lsdpfxszna T Re Apmehk

Condition: used, Year of construction: 2005, functionality: fully functional, machine/vehicle number: MST-0800C0028, For sale: automatic plastic injection molding machine ATEC HQ-800QL. Year of manufacture – 2005 (04), Serial No. MST-0800C0028. Hydraulic system with digital control panel, suitable for serial production of plastic parts. Power supply 380 V, 50 Hz, 3 phases. Used, fully equipped, previously operated in production. Suitable for manufacturing technical, packaging, and industrial plastic components. Inspection on site possible. Lhodpfx Aox Nhy Rspmok

Condition: good (used), screw diameter: 70 mm, displacement volume: 1,500 cm³, 30476 - Ø 70 mm – ENGEL complete plasticizing unit D Complete plasticizing unit for the injection molding side "3550", screw diameter = 70 mm, displacement volume = 1500 ccm, injection pressure = 2250 bar. Lhedpfozvx Snex Apmjk

Condition: good (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 243708, screw diameter: 15 mm, total length: 2,500 mm, total width: 1,500 mm, total height: 2,500 mm, overall weight: 1,700 kg, power: 39 kW (53.03 HP), input frequency: 50 Hz, input voltage: 400 V, input current: 64 A, controller manufacturer: SELOGICA, control voltage: 230 V, ARBURG ALLROUNDER 220 S 180-70 injection molding machine - Rated current for motor heater: 57 A - Includes core puller, manufacturer: MARCZINKOWSKI Please note: the item must be picked up on September 3, 2026, at a date to be confirmed. Lhedpfx Aezldp Rjpmek FCA D-58507 Lüdenscheid - loaded onto a truck.

Condition: good (used), Year of construction: 1999, functionality: fully functional, machine/vehicle number: 178759, clamping force: 2,000 kN, screw diameter: 35 mm, installation height: 350 mm, total length: 5,000 mm, total width: 2,200 mm, total height: 3,800 mm, overall weight: 13,000 kg, power: 53.5 kW (72.74 HP), input frequency: 50 Hz, input voltage: 400 V, controller manufacturer: ARBURG, table diameter: 1,500 mm, ARBURG ALLROUNDER 1500 T 2000-350 Injection Molding Machine Ljdpfx Ajzlfmkopmehk - Clamping force: max. 85 kN - Opening force: max. 120 kN - Opening stroke: max. 300 mm - Distance between mold plates: max. 650 mm - Screw travel: max. 145 mm Note: The item must be picked up between September 8th and 10th, 2026, on a date to be confirmed. FCA D-63128 Dietzenbach – loaded onto a truck.

Condition: ready for operation (used), Year of construction: 2010, operating hours: 23,905 h, functionality: fully functional, clamping force: 600 kN, screw diameter: 35 mm, displacement volume: 135 cm³, injection pressure: 2,221 bar, opening stroke: 335 mm, total length: 2,420 mm, total width: 1,700 mm, total height: 3,100 mm, overall weight: 6,700 kg, Equipment: documentation/manual, For sale: Well-maintained injection moulding machine ENGEL INSERT 200V/60 with only 23,905 operating hours. The machine was used exclusively for sampling purposes. Inspection under power possible at any time! Technical specifications as per the pictures! Ledoy Iwlajpfx Apmshk Machine is immediately available!

Condition: excellent (used), Year of construction: 2008, Min. tool mounting height: 200 mm Max. tool mounting height: 350 mm Max. opening stroke: 380 mm Screw diameter: 22 mm Clamping force: 800 kN Tie bar spacing: 470 x 420 mm Lodozkfd Tjpfx Apmshk Delivery does not include attachments/accessories. The machine is in very good condition and is powered on.

Condition: excellent (used), Year of construction: 1998, Min. tool mounting height: 200 mm Max. plate distance: 550 mm Column spacing: 270 x 270 mm Ledpfxjzkfh Ss Apmohk Screw diameter: 15 mm Clamping force: 400 kN Includes temperature control unit Includes handling robot The machine is in very good condition and is operational.

Condition: good (used), Year of construction: 1992, Clamping force: 500 kN Lsdpfsvygh Nox Apmohk Screw diameter: 30 mm Weight: 3,200 kg Available immediately from stock

Condition: good (used), Year of construction: 1998, Screw diameter: 25 mm Clamping force: 25 tons Opening stroke: 350 mm Weight: 2,900 kg Lsdpfx Apsvxh Iujmshk Immediately available from stock

Condition: excellent (used), Year of construction: 2008, JSW J350AD Injection Molding Machine Electric injection molding machine Year of manufacture: 2009 Type: Electric injection molding machine Total installed power: 30 kW Clamping unit • Clamping force: 3440 kN • Distance between columns (H × V): 730 × 730 mm • Minimum mold height: 300 mm • Maximum mold height: 670 mm • Maximum mold opening stroke: 700 mm • Maximum ejector stroke: 152 mm • Maximum ejector pin height: 365 mm • Diameter of centering ring: Ø 160 mm • Dimensions of mold mounting plates (H × V): 1085 × 1085 mm Injection unit Lodpfxszvwwvs Apmjhk • Screw diameter: Ø 66 mm • Maximum injection shot weight for PS: 890 g • Maximum injection shot weight for PP: 767 g • Maximum injection speed: 160 mm/s • Maximum injection pressure: 1770 bar • Nozzle orifice diameter: 6 mm

Condition: excellent (used), Year of construction: 2017, ENGEL DUO 11050/2300 injection molding machine Lhjdpfx Ajzvwl Topmok Year of manufacture: 2004 Operating hours: 70,029 h Type: hydraulic, two-platen, large-format injection molding machine Clamping unit • Clamping force: 23,000 kN / 2300 t • Dimensions of mounting plates: 2900 × 2500 mm • Distance between columns: 2000 × 1600 mm • Minimum mold height: 700 mm • Maximum mold height: 1890 mm • Maximum opening width: 3800 mm Injection unit • Screw diameter: 135 mm • Injection volume: 8870 cm³ • Injection shot weight for PS: 8071 g • Maximum injection pressure: 1600 bar • Screw: replaced in 2011 • Screw design: reinforced, adapted for processing special materials Additional equipment • Magnetic plates for mold mounting – functional and ready for use • Number of hydraulic cores: 2 • Number of mold heating zones / hot runner channels: 36 • Number of hydraulic cascades: 10 • Mold tilting option • Robot: not included Magnetic mold clamping system The machine is equipped with functional magnetic plates, enabling quick mold mounting and replacement. The system is fully operational and constitutes a significant piece of additional equipment for the machine, especially with frequent mold changes. Machine weight • Weight of the main unit: approx. 113 t • Weight of the control cabinet and additional elements: approx. 18 t • Total approximate weight: approx. 131 t

Condition: excellent (used), Year of construction: 2017, WITTMANN BATTENFELD Macro Power 900/8800 injection molding machine Year of manufacture: 2017 Serial number: 138337-100 Machine with Wittmann robot Clamping unit • Clamping force: 9,000 kN / 900 t • Opening force: 300 kN Ledpfx Aezvwiropmshk • Maximum opening stroke: 2,100 mm • Minimum mold height: 500 mm • Maximum mold height: 1,000 mm • Maximum distance between platens: 3,100 mm (with max. mold height of 1,000 mm) • Dimensions of mounting platens: 1,720 × 1,550 mm • Distance between columns: 1,200 × 1,000 mm • Ejector stroke: 300 mm • Ejector force: 165 kN Injection unit 8800 • Screw diameter: 105 mm • Screw pitch: 525 mm • L/D ratio: 22:1 • Theoretical injection volume: 4,545 cm³ • Maximum injection pressure: 1,931 bar • Maximum screw speed: 167 rpm • Maximum plasticizing rate: 151 g/s • Screw torque: 8,000 Nm • Maximum volumetric flow rate: 725 cm³/s • Injection flow rate with dual pump – option: 906 cm³/s • Nozzle stroke: 950 mm • Nozzle clamping force: 129 kN • Cylinder heating capacity: 53.9 kW • Number of cylinder heating zones: 7 Hydraulic system / drive • Pump power: 90 kW • Oil tank capacity: 1,100 l • Heating power: 53.9 kW Dimensions and weight • Machine length: 10,100 mm • Machine width: 3,400 mm • Machine height: 2,700 mm • Machine weight: 35,200 kg / 35.2 t

Condition: used, Battenfeld BEX-1-150-32-D-V / BEX 45-25E / 89-9436-3201 extruder machine. Manufacturer: Battenfeld-cincinnati Germany GmbH. Year of manufacture: 1999 Year of installation: 1999 Rated voltage: … V Maximum current consumption: … A Frequency: 50 Hz Required pressure: 6 bar Total weight: … kg Noise level: … dB Hydraulic pressure for the screen changer: Extrusion material output: 1000-1200 kg (filter-limited output: approx. 850 kg) Possible thickness: 1 – 5 mm Maximum width: approx. 1450-1480 mm Machine dimensions: as described in the layout. Battenfeld BEX-1-150-32-D-V / BEX 45-25E / 89-9436-3201 extruder machine Ljdpszump Eofx Apmjhk Consisting of: Screw and barrel assembly, motor and drive system, control interface, and supporting auxiliary systems for feeding, thermal regulation, and downstream processing. Details: Feed station - 2x silos. 2 x metal separators - Degacan HE degassing elements, co-extruder Type BEX-1-150-32-D-V and BEX 45-25E / 89-9436-320 to produce sheets or coils. Main extruder composed of 7 heating zones and one vacuum zone. Co-extruder composed of 3 heating/cooling zones to control the polymer. Followed by 3 calenders with temperature controllers. Extrusion die - To be confirmed if included. Calender line setup. Betacontrol Mk1 thickness measuring system. Radioactive source has been removed. Calvatron corona treatment system. Kalvar Calvtron automatic coil changing system. Rollers and calibration table. End-of-line sheet separation and side cutting (slitting) machine. BC touch control interface. Full workshop manuals.

Condition: excellent (used), Year of construction: 2015, KRAUSS-MAFFEI KM 900-8100 GX injection molding machine Year of manufacture: 2015 Clamping force: 9000 kN / 900 t Control system: MC6 Closing system: hydraulic-mechanical, two-platen Injection unit: 8100 Design and control Hydraulic-mechanical two-platen closing system with 4 pressure cushions on the stationary platen and 4 adjusting units on the moving platen. PV – injection unit adjustment. MC6 control system, based on an industrial computer with real-time Ethernet technology, equipped with an integrated 19-inch control panel with a color touchscreen, LED backlighting, and ProcessDesigner process visualization. Plasticizing unit Complete plasticizing unit for thermoplastics, featuring abrasion protection. Screw diameter: 105 mm Backflow valve: yes Nozzle: open Closing unit Mold clamping force: 9000 kN / 900 t Mold opening force – pressure cushions: 630 kN Dimensions of mounting plates (H × V): 1660 × 1530 mm Distance between columns (H × V): 1180 × 1000 mm Maximum mold opening stroke: 1600 mm Mold height min./max.: 500–1100 mm Maximum distance between platens: 2100 mm Ejector stroke: 300 mm Ejector force front / rear: 140 / 70 kN Injection unit 8100 Screw diameter: 105 mm Ls/D ratio: 23:1 Maximum injection pressure: 1778 bar Lhodpfezvm T Tjx Apmjk Injection volume: 4546 cm³ Injection weight for PS: 3228 g Injection rate: 805 cm³/s Screw speed: 150 rpm Nozzle clamping force: 166 kN Electrical and hydraulic equipment Rated power of pump motor: 120 kW Installed power of heaters: 59 kW Number of cylinder heating zones: 7 Dry cycle time / stroke according to EUROMAP 6: 3.3 s / 826 mm Dry cycle time / stroke according to KraussMaffei standards: 2.9 s / 590 mm Oil tank capacity: 1450 l Dimensions and weight Machine dimensions (L × W × H): 10.72 × 3.03 × 2.51 m Net weight including control cabinet: 40 t

Condition: excellent (used), Year of construction: 2018, KRAUSS-MAFFEI KM 900-8100 GX injection molding machine Year of manufacture: 2018 Control system: MC6 Clamping system: hydraulic-mechanical, two-platen Injection unit: 8100 Design and control Hydraulic-mechanical two-platen clamping system with 4 pressure pads on the fixed platen and 4 adjustment units on the moving platen. PV – injection unit adjustment. MC6 control system, based on an industrial computer operating with real-time Ethernet technology. Integrated 19-inch control panel with a color touchscreen, LED backlighting, and visualization of all running ProcessDesigner processes. Plasticizing unit Complete plasticizing unit for thermoplastics with abrasion protection. Screw diameter: 105 mm Backflow valve: yes Nozzle: open Nozzle radius: 25 mm Nozzle opening: 9 mm Clamping unit Clamping force: 9000 kN / 900 t Mold opening force: 630 kN Platen dimensions (H × V): 1660 × 1530 mm Distance between columns (H × V): 1180 × 1000 mm Standard maximum distance / opening width: 2100 mm Ejector stroke: 300 mm Ejector force front / rear: 140 / 70 kN Injection unit 8100 Screw diameter: 105 mm Ls/D ratio: 23:1 Maximum injection pressure: 1778 bar Injection volume: 4546 cm³ Injection weight: 3228 g* Injection speed: 90 mm/s Injection rate: 779 cm³/s Standard screw speed: 150 rpm Plasticizing rate at standard speed: 135 g/s* Nozzle pressure force: 166 kN * according to the manufacturer's specifications / reference material provided. Electrical and hydraulic equipment Rated motor power: 120 kW Installed heater power: 59 kW Number of cylinder heating zones: 7 Dry cycle time / stroke according to EUROMAP 6: 3.3 s / 826 mm Dry cycle time / stroke according to KraussMaffei standards: 2.9 s / 590 mm Required hydraulic oil quantity: 1450 l Dimensions and weight Ljdszvm E Aopfx Apmehk Machine dimensions (L × W × H): 10.72 × 3.03 × 2.51 m Net weight including control cabinet: 40.0 t

Condition: excellent (used), Year of construction: 2013, KRAUSS-MAFFEI KM 550-4300 GX injection molding machine Year of manufacture: 2013 Control system: MC6 Clamping system: hydraulic-mechanical, two-platen Injection unit: 4300 Design and control Hydraulic-mechanical two-platen clamping system with 4 pressure pads on the fixed platen and 4 adjustment units on the moving platen. Ledpfxezvm Dlo Apmohk PV – injection unit adjustment. MC6 control system with a color TFT monitor, integrated control panel, and USB data storage. Plasticizing unit Complete plasticizing unit for thermoplastics with abrasion protection. Screw diameter: 90 mm Backflow valve: yes Nozzle: open Clamping unit Clamping force: 5500 kN / 550 t Mold opening force – pressure pads: 385 kN Platen dimensions (H × V): 1430 × 1350 mm Distance between columns (H × V): 1040 × 910 mm Maximum mold opening stroke: 1350 mm Minimum/maximum mold height: 400–950 mm Maximum distance between platens: 1750 mm Ejector stroke: 250 mm Ejector force front / rear: 95 / 49 kN Injection unit 4300 Screw diameter: 90 mm Ls/D ratio: 20:1 Maximum injection pressure: 1839 bar Injection volume: 2290 cm³ Injection weight for PS: 2084 g Injection rate: 636 cm³/s Screw speed: 195 rpm Nozzle clamping force: 129 kN Electrical and hydraulic equipment Rated motor power: 90 kW Installed heater power: 44 kW Number of cylinder heating zones: 7 Dry cycle time / stroke according to EUROMAP 6: 2.8 s / 728 mm Dry cycle time / stroke according to KraussMaffei standards: 2.5 s / 520 mm Oil tank capacity: 1180 l Dimensions and weight Machine dimensions (L × W × H): 8.08 × 2.80 × 2.39 m Net weight with control cabinet: 25.0 t

Condition: excellent (used), Year of construction: 2013, KRAUSS-MAFFEI KM 850-8100 MX injection molding machine – with servo drive Year of manufacture: 2013 Control system: MC5 Clamping system: hydraulic-mechanical, two-platen Drive: hydraulic with servo drive Ljdpfx Apjzvm A Ijmshk Design and control Hydraulic-mechanical, two-platen clamping system with 4 pressure cushions and 4 adjusting units mounted on the moving platen. PV – injection unit adjustment. MC5 PC (Pentium) control system with a color TFT monitor, integrated control panel, and USB data storage. Plasticizing unit Complete plasticizing unit for thermoplastics with wear-resistant coating. Screw diameter: 105 mm Backflow valve: yes Nozzle: open Clamping unit Clamping force: 8500 kN / 850 t Opening force: 560 kN Mold mounting plate dimensions (H × V): 1600 × 1600 mm Distance between tie bars (H × V): 1140 × 1140 mm Mold opening stroke: 1600 mm Minimum/maximum mold height: 500–1100 mm Maximum distance between platens: 2100 mm Ejector stroke: 300 mm Ejector force, front/rear: 200 / 100 kN Injection unit 8100 Screw diameter: 105 mm Maximum injection pressure: 1778 bar Injection volume: 4546 cm³ Injection weight for PS: 4137 g Injection rate: 805 cm³/s Screw speed, standard / optional: 121 / 153 rpm Electro-hydraulic equipment Servo drive for the hydraulic system: YES Rated power of the pump motor: 110 kW Number of dry cycles according to EUROMAP 6: 965 cycles/h Oil tank capacity: 1500 l Dimensions and weight Machine dimensions (L × W × H): 10.81 × 2.92 × 2.57 m Net weight with control cabinet: 43.5 t

Condition: excellent (used), Year of construction: 2014, KRAUSS-MAFFEI KM 420-4300 CX injection molding machine Year of manufacture: 2014 Control system: MC6 Plasticizing unit: 4300 Screw diameter: 90 mm Control system MC6 control system, based on an industrial computer operating with real-time Ethernet technology. Integrated 19-inch control panel with a color touchscreen, LED backlight, and visualization of all running processes via ProcessDesigner. Plasticizing unit Complete plasticizing unit for thermoplastics with abrasion-resistant design. Screw diameter: 90 mm Backflow valve: yes Nozzle: open Nozzle radius: 15 mm Nozzle orifice: 6 mm Clamping unit Clamping force: 4200 kN / 420 t Maximum mold opening force: 250 kN Dimensions of mounting plates (H × V): 1270 × 1230 mm Distance between columns (H × V): 800 × 800 mm Maximum mold opening stroke: 1020 mm Minimum mold height: 380 mm Maximum distance between plates: 1400 mm Ejector stroke: 250 mm Ejector force front / rear: 95 / 49 kN Injection unit 4300 Screw diameter: 90 mm Ls/D ratio: 20 Maximum injection pressure: 1839 bar Injection volume: 2290 cm³ Injection weight for PS: 2084 g Standard injection rate: 604 cm³/s Injection rate with accumulator: 1909 cm³/s Standard screw speed: 195 rpm PS plasticizing rate at standard speed: 134 g/s PS plasticizing rate at increased speed: 186 g/s Nozzle clamping force: 129 kN Electrical and hydraulic system Rated power of pump motor: 90 kW Installed heater power: 44 kW Ljdjzvmx Nepfx Apmjhk Number of cylinder heating zones: 7 Dry cycle time / stroke according to EUROMAP 6: 2.8 s / 560 mm Oil tank capacity: 1000 l Dimensions and weight Machine dimensions (L × W × H): 7.6 × 2.5 × 2.4 m Net weight including control cabinet: 25.5 t

Condition: excellent (used), Year of construction: 2011, KRAUSS-MAFFEI KM 420-4300 CX Injection Molding Machine YEAR OF MANUFACTURE - 2011 Control System: MC5 with color monitor, integrated control panel, and 3 USB ports Plasticizing Unit Complete plasticizing unit for thermoplastics, designed for abrasion resistance Screw diameter: 90 mm Back pressure valve: yes Nozzle: open Lsdpfx Aezvmxpspmjhk Clamping Unit Clamping force: 4200 kN / 420 t Opening force: 249.6 kN Force of moving platen – opening: 124.7 kN Force of moving platen – closing: 102.4 kN Dimensions of mounting platens (H × V): 1270 × 1200 mm Distance between columns (H × V): 800 × 800 mm Mold opening stroke: 1020 mm Minimum mold height: 380 mm Maximum clearance / opening stroke of platens: 1400 mm Ejector stroke: 250 mm Ejector force: 95.4 / 48.6 kN Injection Unit 4300 Screw diameter: 90 mm Maximum injection pressure: 1839 bar Injection volume: 2290 cm³ Injection weight for PS: 2084 g Screw speed – standard/option: 195 / 270 rpm Electrical and hydraulic equipment Rated power of pump motor: 90 kW Installed power of heaters: 44 kW Number of cylinder heating zones: 7 Number of dry cycles according to EUROMAP 6: 1300 cycles/h Oil tank capacity: 1075 l Dimensions and weight Machine dimensions (L × W × H): 7.6 × 2.6 × 2.5 m Net weight with control cabinet: 24.2 t

Condition: excellent (used), Year of construction: 2011, KRAUSS-MAFFEI KM 420-4300 CX Injection Molding Machine YEAR OF MANUFACTURE - 2011 Control System: MC5 with color monitor, integrated control panel, and 3 USB ports Plasticizing Unit Complete plasticizing unit for thermoplastics, designed for abrasion resistance Screw diameter: 90 mm Back pressure valve: yes Nozzle: open Clamping Unit Clamping force: 4200 kN / 420 t Opening force: 249.6 kN Force of moving platen – opening: 124.7 kN Force of moving platen – closing: 102.4 kN Lsdpfezvmpnjx Apmshk Dimensions of mounting platens (H × V): 1270 × 1200 mm Distance between columns (H × V): 800 × 800 mm Mold opening stroke: 1020 mm Minimum mold height: 380 mm Maximum clearance / opening stroke of platens: 1400 mm Ejector stroke: 250 mm Ejector force: 95.4 / 48.6 kN Injection Unit 4300 Screw diameter: 90 mm Maximum injection pressure: 1839 bar Injection volume: 2290 cm³ Injection weight for PS: 2084 g Screw speed – standard/option: 195 / 270 rpm Electrical and hydraulic equipment Rated power of pump motor: 90 kW Installed power of heaters: 44 kW Number of cylinder heating zones: 7 Number of dry cycles according to EUROMAP 6: 1300 cycles/h Oil tank capacity: 1075 l Dimensions and weight Machine dimensions (L × W × H): 7.6 × 2.6 × 2.5 m Net weight with control cabinet: 24.2 t

Condition: excellent (used), Year of construction: 2011, KRAUSS-MAFFEI KM 420-4300 CX Injection Molding Machine YEAR OF MANUFACTURE - 2011 Control System: MC5 with color monitor, integrated control panel, and 3 USB ports Plasticizing Unit Complete plasticizing unit for thermoplastics, designed for abrasion resistance Screw diameter: 90 mm Back pressure valve: yes Nozzle: open Clamping Unit Clamping force: 4200 kN / 420 t Opening force: 249.6 kN Force of moving platen – opening: 124.7 kN Force of moving platen – closing: 102.4 kN Dimensions of mounting platens (H × V): 1270 × 1200 mm Distance between columns (H × V): 800 × 800 mm Mold opening stroke: 1020 mm Minimum mold height: 380 mm Maximum clearance / opening stroke of platens: 1400 mm Ejector stroke: 250 mm Ejector force: 95.4 / 48.6 kN Injection Unit 4300 Screw diameter: 90 mm Lodpfszvgu Dox Apmshk Maximum injection pressure: 1839 bar Injection volume: 2290 cm³ Injection weight for PS: 2084 g Screw speed – standard/option: 195 / 270 rpm Electrical and hydraulic equipment Rated power of pump motor: 90 kW Installed power of heaters: 44 kW Number of cylinder heating zones: 7 Number of dry cycles according to EUROMAP 6: 1300 cycles/h Oil tank capacity: 1075 l Dimensions and weight Machine dimensions (L × W × H): 7.6 × 2.6 × 2.5 m Net weight with control cabinet: 24.2 t

Condition: good (used), Year of construction: 1996, operating hours: 24,222 h, functionality: fully functional, Description Type BOY 80M Year of manufacture 1996 Operating hours 24,222 hours Screw (high wear resistance) 42 mm Injection pressure max. 1532 bar Shot volume max. 200 cm3 Lhedpfx Aszvdmqopmsk Closing force 80 T Max. distance between tie bars 410 mm Min. mold height 250 mm Distance between platens max. 725 mm Dimensions 1,000 x 3,395 x 1,995 mm (L x W x H) Weight 3250 kg Options: • Core pull • Includes a Procan control system. • High wear-resistant 42mm screw and cylinder • Color contact (potential-free, max 5A) • Signal control for coloring The machine has recently been tested and is fully operational!

Condition: excellent (used), Year of construction: 2005, ENGEL VICTORY 2050/300 POWER injection molding machine Year of manufacture: 2005 Serial number: 155108 Control system: ENGEL CC200 Operating hours: approx. 88,000 h Design: columnless – Tie-Bar-Less Drive: hydraulic Clamping unit Clamping force: 3000 kN / 300 t Clamping system: ENGEL POWER – hydraulic, columnless Opening stroke: 900 mm Minimum mold height: 350 mm Maximum daylight opening: 1250 mm Dimensions of mounting plates: 1100 × 1000 mm Injection unit Injection unit: 2050 Screw diameter: 70 mm Injection volume: 1155 cm³ Injection weight for PS: approx. 1050 g Maximum injection pressure: approx. 1700 bar Screw L/D ratio: approx. 20:1 Control and equipment Control system: ENGEL CC200 Interface / robot preparation: yes Lhodpfx Aezvdbuspmek Robot: none Hydraulic core control: 2 circuits Central lubrication system: yes Hydraulic oil cooling: yes Power supply Voltage: 400 V Frequency: 50 Hz Dimensions and weight Machine length: approx. 7300 mm Machine width: approx. 2200 mm Machine height: approx. 2500 mm Machine weight: approx. 20,400 kg