Used Lead Cartridge for sale (1,753)

Condition: used, SLM Solutions Type: SLM 280 HL For sale is a professional metal 3D printing system, type SLM 280 2.0, from SLM Solutions (Lübeck). The SLM is designed for 24/7 operation and was last used with titanium. Installation was in 2018. The system already has the sintering walls for gas flow. The system has only been operated with argon for the last 3 years. Approx. 50,000 laser hours. The 50,000 hours refer to the laser on-time; the exposure time is not recorded in the older 280 models. If I disregard the coating time, I estimate approximately 10,000 active laser hours. Last maintenance was in early 2026. Dcjdpfx Aszhlr Esiijp Currently, occasional communication issues between the PC and the PLC are observed. In rare cases, this can lead to incorrect status messages, which can cause the system to be briefly interrupted during a running job. Technical data (excerpt) Single laser 400W Weight: 1,245 kg Build volume: 280 × 280 × 365 mm Laser: 1 × 400 W fiber laser (IPG) Optics: 3D galvo system Focus diameter: 80 – 115 µm Max. scanning speed: up to 10 m/s Layer thickness: 20 – 90 µm Minimum feature size: approx. 150 µm Build speed: up to approx. 113 cm³/h (material-dependent) Materials: Stainless steel, tool steel, titanium (Ti64), aluminum, Inconel, CoCr Inert gas: Argon Gas consumption process: approx. 2.5 – 8 l/min Gas consumption purging: approx. 70 – 110 l/min Compressed air: approx. 6 – 7 bar Electrical: 400 V, 3P+N+PE Fuse: 63 A Power consumption: approx. 3.5 – 5.5 kW Machine dimensions: approx. 2600 × 1200 × 2700 mm Weight: approx. 1300 kg (empty), up to approx. 1800 kg (including powder) Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of supply: (See image) SLM 280 machine Control cabinet Process chamber Internal control panel with screen (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: refurbished (used), Year of construction: 2005, travel distance X-axis: 1,050 mm, travel distance Y-axis: 2,050 mm, travel distance Z-axis: 1,000 mm, workpiece weight (max.): 20,000 kg, table width: 1,140 mm, table length: 1,640 mm, workpiece length (max.): 2,520 mm, workpiece width (max.): 1,520 mm, workpiece height (max.): 945 mm, feed rate Z-axis: 12 m/min, overall weight: 30,000 kg, table load: 20,000 kg, # OPS INGERSOLL GANTRY 1500 / 64 Bit ## Fully Refurbished – Completion Expected 10/2026 For sale is an OPS INGERSOLL wire EDM machine, model GANTRY 1500 / 64 Bit, manufactured in 2005, which is undergoing a comprehensive and professional overhaul in our facility. Upon completion of the overhaul, the machine will be in very good condition, both technically and aesthetically, and will be prepared for immediate use in reliable production operations. ### Technical Data Manufacturer: OPS INGERSOLL Model: GANTRY 1500 / 64 Bit Year of Manufacture: 2005 Condition: Fully Refurbished Completion: Expected 10/2026 Control: Mitsubishi – 64-bit CNC Generator Power: 70 A – Multipulse Travel Ranges X / Y / Z: 1,050 × 2,000 × 1,000 mm Electrode Changer: 15-position pick-up disc changer Working Tank (W × D × H): 1,520 × 2,520 × 945 mm Workpiece Clamping Table (W × D): 1,380 × 2,380 mm Load Capacity: 20,000 kg ### Accessories * CO₂ fire extinguishing system * Cartridge filter system ## Extensive Overhaul The OPS INGERSOLL GANTRY 1500 is undergoing a comprehensive and professional overhaul in our facility. During the overhaul, the machine will be disassembled to over 70%. All relevant components and wear parts will be carefully inspected and, if necessary, professionally refurbished or replaced. ### The following overhaul work will be carried out: * Inspection and, if necessary, replacement of the ball screws and ball bearings of the X, Y, and Z axes * Inspection and, if necessary, replacement of all four ball screws of the tank drive * Inspection and testing of the C-axis for tightness and accuracy * Geometric inspection of all axes according to the OPS INGERSOLL test protocol * Thorough cleaning of the entire machine base * Cleaning of the entire working tank, including replacement of the felt wipers * Overhaul of the dielectric pumps * Replacement of all hydraulic and dielectric lines * Replacement of all pneumatic lines * Thorough cleaning of the control cabinet, generator, and control system * Replacement of all relevant fans and batteries * Overhaul or, if necessary, replacement of power supplies, units, and servo amplifiers * Final laser measurement of the machine after the overhaul ## Quality Control and Erosion Test After completion of all overhaul work, the machine will undergo a comprehensive functional and quality control. This includes, in particular, a detailed erosion test according to the quality and testing specifications of OPS INGERSOLL. The relevant machine functions, as well as accuracy and process reliability, will be checked. ## Ready for Production After Overhaul After successful completion of the overhaul and final inspection, the OPS INGERSOLL GANTRY 1500 / 64 Bit is immediately ready for use. Dedpfxez Atdrj Aiijcp With its high load capacity of 20,000 kg, the generous travel ranges, and the large working area, the machine is particularly suitable for the reliable machining of large and heavy workpieces in demanding production environments. A powerful and comprehensively refurbished wire EDM machine for users who value high machine quality, process reliability, and long-term operational capability. 10/16.

Condition: new, Maximum turning height: 315 mm Turning diameter over the bed: 630 mm Turning diameter over the cross slide: 430 mm Turning diameter in the chuck: 830 mm Distance between centers: 3000 mm Spindle bore: 103 mm Spindle fitting, DIN 55027: Size 11 Bed width: 400 mm 21 speed ranges: 12.5 – 1250 rpm Feed range, longitudinal: 0.04 – 12 mm/rev Feed range, transverse: 0.02 – 6 mm/rev 64 metric threads: 0.5 – 120 mm 64 inch threads: 60 – 1/4“ 64 module threads: 0.125 – 30 module 64 diametral pitch threads: 240 – 1 pitch Tailstock fitting: MK 5 Tailstock quill travel: 230 mm Tailstock quill diameter: 75 mm Drive power: 11 kW Dimensions L x W x H: approx. 5100 x 1400 x 1300 mm Weight: approx. 4800 kg Accessories / Special Features: • 3-axis digital read system, manufacturer K+C • 3-jaw chuck, manufacturer BISON, Ø 315 mm • Quick-change tool holder system “Multifix”, Size C • Powerful main drive with 11 kW • Large spindle bore, Ø 103 mm • Traveling steady rest • Fixed steady rest, small • Fixed steady rest, large • Chuck • Rapid traverse in longitudinal and transverse direction • Electrodynamic brake • Coolant system • Machine light • Quick-change device for the tailstock • Bed stop • Protective shield, rear, full length • Tool holder protection • Chuck protection, electrically secured • Lead and feed screw protection • Interchangeable gears • Fixed center for the spindle • Reducer sleeve for the spindle • Two colors: top light gray RAL 7035, bottom blue RAL 5015 • CE compliant Delivery time: approx. 2 months after order placement Delivery: ex works, manufacturer's plant in Bulgaria, free on board (FOB) truck Warranty period: 12 months, with single-shift operation (8 hours) Siegfried Volz Machine Tools Rüschebrinkstr. 151-153 Dcjdpfxek Dpxlj Aiiop DE - 44143 Dortmund - Wambel

Condition: good (used), Complete line available which was producing toffee apples for the leading producer in England. Toffee apples and candy apples were supplied to several leading supermarket chains. Line consists of cooking vessels for the toffee, robotic pick and dip lines to insert the sticks into the apples, pick them up, dip them in the toffee and then place them onto the cooling belt then the products are conveyed into flowwrappers. Videos available upon request. Dcodpfx Aispitkksiep

Condition: refurbished (used), Year of construction: 1999, Fully refurbished Hosokawa Alpine Pharmapaktor APC L200/30 used standalone system by Alpine Originals. Technical details: Construction materials: Non product contacted parts: stainless steel Product contacted parts: stainless steel Non pressure shock resistant (NPSR) Non ATEX (can be implemented for an additional price) Without vacuum deaeration (can be implemented for an additional price) Scope of supply: Hosokawa Alpine Pharmapaktor APC L 200/30, including feeding, without Flake Crusher. The Hosokawa Alpine APC L200/30 Pharmapaktor is the perfect compactor to test the product behaviour with this technology, while it even allows to keep a continuous production at small scale if needed. The Pharmapaktor can be fitted with a flake crusher to granulate the resulting compacted material increasing the possibilities of end product sizes and forms, from different sort of briquettes to granulates according to the required specification. Thanks to its flexibility, the machine can be adapted to different products and tasks. It even complies with the tough pharmaceutical standards. Compacting head Dcedovq Nlxjpfx Aiiop Two cast stainless steel H-frames connected by spacer bolts. Two laterally foldable swing arms for easy and quick changing of the rollers. The swing arms are fixed with two tie rods, which also absorb the compressive forces of the compacting rollers. One chamber insert for guiding the product flow and two center pieces for sealing the rollers. Pre-compaction unit The pre-compaction unit is mounted on a supporting column and can be lifted and swivelled to the side. The charging hopper (with 2 brake bars) is equipped with a cylindrical/conical precompression screw. When the pre-compaction unit is lifted off, a limit switch switches off the compacting rollers and the screw. A HOSOKAWA ALPINE Originals machine Refurbished by the original manufacturer Use of original components only Original manufacturer warranty Guaranteed manufacturer spare parts supply Short lead time Before delivery, the machine is overhauled, all wear parts are revised and exchanged if needed and customized to your specific needs Possibility to provide all additionally required peripherals or adapt to existing production plant We are also interested in buying back disused HOSOKAWA ALPINE machinery

Condition: like new (used), Vacuum filler Continuous vacuum filler for straight filling and portioning Filling mechanism: with rotary vane pump with 16 sliding rules, standard Hopper approx. 250 liters, with loading screw, dismantable, with limiter Built-in portioning computer PC Portion weight: 5 - 60.000 gr Dsdpsu Ndlbsfx Aiijcp Filling speed: 0 - 100 % depending on type of the wrapper and portion size Steplessly adjustable filling speed VEMAG lifting device Built-in Hydraulic leading Access also from backside Arm Nirosta for standard trolley according to DIN 9797, 200 liters volume Machine dimensions in cm: Width: 130,0 Length: 220,0 Height: 200,0 Installed power: 9,5 kW Voltage: 380 V, 50 Hz Weight: approx. 1 300 kg

Condition: used, Year of construction: 1975, Technical details: turning diameter over bed: 500 mm turning diameter over support: 260 mm turning length: 950 mm center height measured in bed: 220 mm centre distance: 1000 mm revolution per minute: 11,2 - 2240 / 24 step U/min spindle bore of work spindle: 62 mm tailstock quill adjustment:: 210 mm longitudinal feeds:: 0,045 - 1,6 mm/U - 32 step cross feed: 0,02 - 0,71 mm/U - 32 step total power requirement: 11 kW Dcjdpfxsv A Sqhs Aiijp weight of the machine ca.: k.A. t dimension machine xH: 3,3 x 1,2 x 1,6 m The machine is in a very good condition (very quiet spindle run) in Leipzig. Top slide rotatable 360° 3-jaw lathe chuck Ø 315mm with jaws (inside/outside) for speed 2000 rpm. Thread cutting: metric, modular thread, inch Chip protection wall Chuck protection (mechanical) MULTIFIX steel holder with Ø 40mm drill steel holder Chip collection tray Coolant supply with pump Protective device for lead screw Machine base UVV is pre-equipped ( UVV=Accident Prevention Regulations) *

Condition: refurbished (used), battery capacity: 930 Ah, battery voltage: 48 V, total height: 784 mm, total length: 835 mm, total width: 742 mm, Tested forklift battery for your truck – 48V 6PZS 930AH – DIN A + 1 year warranty + incl. Aquamatic system + incl. end discharge lead & REMA 320 connector (other connectors available upon request) + Capacity: min. 90–100% (C5 capacity protocol is included upon delivery) + Year of manufacture: 2024 Dimensions: Length 984 mm Width 630 mm Height 650 mm Weight: approx. 1,050 kg Suitable for the following models and more: Linde E 18 – 322-00 Linde E 18 – 386-02 – side battery change Linde E 18 Z – 322-00 Linde E 20 PHL – 335-00 Linde E 20 PHL – 386-00 Linde E 20 PHL – 386-02 Linde V – 5213-00 Linde V – 5213-01 Dsdpsy Rntysfx Aiiscp Linde V MODULAR – 5213-00 Linde V MODULAR – 5214-00 Toyota/BT RR-B 8 Common battery sizes available on request. Transport possible.

Year of construction: 2020, condition: used, Offered for sale is a manual powder coating booth with a cartridge filter system. Technical data: Usable volume: 9.5m³, airflow rate: 12000m³/h, downward air velocity: 0.25-0.3m/s, total filter area: 160m², maximum powder melting point: 220°C, maximum dimensions X/Y/Z: 2200mm/200mm/2000mm. Control system: Integrated spray gun and control unit for manual powder coating. Equipment: Booth, platform, filter system, eight cartridges. Operation: 2020/2021 two-shift operation, subsequently approx. 30% daily utilization. System documentation available. Inspection possible by arrangement. Dcedpfx Aijz Rn Dnoisp

Year of construction: 1982, condition: used, Offered for sale is a conventional center lathe with lead screw and feed rod. Distance between centers: 3000mm. Swing over bed: 710mm. Center height: 342mm. Spindle speed range: 8-1250rpm. Number of spindle speed steps: 23. Longitudinal feed: 0.056-10mm/rev. Cross feed: 0.028-5mm/rev. Metric thread pitches: 1-176mm. Max. workpiece weight between centers: 2500kg. Max. workpiece weight between centers with steady rest: 3000kg. Tailstock quill travel: 300mm. Equipped with digital readout, three-jaw chuck, four-way tool post and tailstock. Weight: approx. 5400kg. Overall dimensions X/Y/Z: approx. 5325mm/1510mm/1510mm. Inspection possible by arrangement. Dsdpfxs Ad Nq Ie Aiiocp

Condition: used, Year of construction: 1998, Transnorm Rising falling Incline belt conveyor with leading belt GF 25000+4000-1000-900 RA2288 Technical data: Conveyor length (NL): 29000 mm ( 25000 mm riser segment + 4000 mm forerun) frame width (NB): 1000 mm, 1100 mm with motor belt width (GuB): 900 mm Overall height (BH): 80 mm, 430 mm with motor Angle: freely adjustable between 0 and 15° Supporting feet: optionally available Conveying speed (v m/s): 0,2 Drive: SEW gear motor, Electrical data: 50Hz V380-500, kW2,2 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Optionally available: Supports Side guide on one side and on both sides Frequency converter for stepless speed change Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Dcodpfx Ajtp Tv Esiiep Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: used, Year of construction: 2014, Transnorm Rising falling Incline belt conveyor with leading belt GF 1300+6000+1900-700-600 RA2072 Technical data: Conveyor length (NL): 9200 mm ( 1900 mm arch + 6000 mm riser segment + 1300 mm leading ) frame width (NB): 700 mm, 800 mm with motor belt width (GuB): 600 mm Overall height (BH): 80 mm, 430 mm with motor Angle: freely adjustable between 0 and 15° Supporting feet: optionally available Conveying speed (v m/s): 0,42 Drive: SEW gear motor, R27 DRS71M4BE1/MM07/LN Electrical data: 50Hz V380-500, kW 0,75 S1 Drive drum: Ø = 81 mm Belt return roller: Ø = 81 mm Djdpfx Aijn N A Ifsiecp Optionally available: Supports Side guide on one side and on both sides Frequency converter for stepless speed change Adjust length (longer/shorter) Prices net plus VAT ex central warehouse Dr. Sonntag GmbH & Co KG, 97076 Würzburg, Germany For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: used, 3D SYSTEMS Professional MultiJet 3D Printer / MJP System 3D Systems ProJet MJP 2500 Plus MultiJet Printing with HD and UHD print modes For sale is a used, professional 3D printer from the manufacturer 3D Systems. The ProJet MJP 2500 Plus is suitable for producing precise plastic components, functional prototypes, concept models, as well as fixtures and tooling applications. Technical data: Manufacturer: 3D Systems Model: ProJet MJP 2500 Plus Technology: MultiJet Printing (MJP) Print modes: HD / UHD Max. build volume: 294 × 211 × 144 mm HD resolution: 800 × 900 × 790 DPI Layer thickness HD: 32 µm UHD resolution: 1600 × 900 × 790 DPI Layer thickness UHD: 32 µm Dimensions (W × D × H): 1120 × 740 × 1070 mm Weight: 211 kg Power supply: 200–240 V / 50 Hz / 1-phase / 10 A Internal hard drive: at least 500 GB Operating temperature: 18–28 °C Interfaces: Ethernet / USB Equipment: Integrated touch display Material system for build and support material Automatic switching of material cartridges Network connection USB connection 3D Sprint software support Material containers as shown in the pictures Application areas: Dodpfx Aez Erdaeiiscp Functional prototypes Concept models Form and fit testing Fixtures and holders Tooling applications Product development Additive manufacturing Scope of delivery: 1 × 3D Systems ProJet MJP 2500 Plus Material containers as shown in the pictures Additional accessories as shown in the pictures Condition: Used Optical condition as shown in the pictures Shipping via freight forwarder is possible. Subject to changes, errors and prior sale. We will be happy to answer any further questions by telephone.

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, rotary table diameter: 450 mm, position of the milling head: Schwenkbar (45°), table diameter: 450 mm, total length: 5,600 mm, gear diameter: 500 mm, total height: 3,100 mm, total width: 3,600 mm, input frequency: 50 Hz, type of input current: three-phase, spindle speed (max.): 340 rpm, table bore: 125 mm, spindle speed (min.): 80 rpm, travel distance X-axis: 325 mm, travel distance Y-axis: 200 mm, travel distance Z-axis: 400 mm, overall weight: 14,800 kg, distance table to spindle center: 350 mm, tool diameter: 200 mm, controller manufacturer: Siemens Sinumerik 840D sl, drive type: Sinamics S120, control type: CNC control, Equipment: documentation/manual, rotational speed infinitely variable, A Pfauter PE 500 for the economical production of straight and helical spur gears up to module 12 and 500 mm in diameter – completely overhauled by SerWeMa with Siemens Sinumerik 840D sl, equipped with a gripper unit and a 32-position workpiece storage for unmanned operation. The machine is ready for operation in our hall in Chemnitz: you can inspect it under power, and if desired, we will mill your own sample part and you can take delivery of the machine here. No delivery time, no risk. Sold by Serwema Retrofit Solutions, the company that carried out the overhaul and knows the machine inside out. The general overhaul included complete geometric overhaul by grinding and scraping, new roller bearings in the main drive and in the milling head, measuring and reconditioning the worm gear, overhauled or new ball screw drives, overhaul of hydraulics, lubrication and coolant system, and new electrical equipment with Sinumerik 840D sl, Sinamics S120 and new axis motors. An electronic generating gear controls all generating and single-part machining processes, and an NC-controlled crash recovery protects the tool and workpiece in the event of a power or phase failure. New paint in RAL 7035/5015 with oil and coolant resistant two-component paint, acceptance of geometry according to SerWeMa protocol based on DIN ISO 6545. The machine controls six CNC axes: X radial, Y tangential, Z axial, A milling head swivel, B milling cutter drive and C table drive. The SerWeMa gear cutting software guides you through workpiece and tool data via masks, without the need for programming: up to three position-oriented gearings per workpiece, each with its own tool, up to three cuts per gearing with simultaneous or counter-rotating movement, form corrections for convex, conical and convex-conical profiles, lead-in and lead-out phase correction, chamfer milling, dimension correction via tooth width, two-roll or two-ball gauge, measuring stop, shift strategy with defect management per generating cutter and cutting force monitoring with automatic retraction. Technologies: generating milling, single-part milling and worm gear milling both radially and tangentially. A hand-held device with a handwheel allows setup directly in the working area. Djdpfxsz Et E Ee Aiiscp Technical data: max. workpiece Ø 500 mm, max. module 12, max. milling cutter Ø 200 mm, max. milling cutter length 240 mm, shift travel 200 mm, milling cutter speed 100–450 rpm, swivel angle +25°/−45°, travel radial 325 mm (axis distance 25–350 mm), travel axial 400 mm (310–710 mm), table diameter 450 mm, table bore 125 mm, connection power approx. 60 kVA. Installation dimensions incl. automation approx. 7.2 × 4.5 × 3.3 m, weight approx. 16.8 t. Equipment: machine enclosure, chip conveyor, gripper unit with two grippers, workpiece storage with 32 positions, preparation for emission extraction (150 mm nozzle, Harting connector on the machine roof). Documentation complete in German: operating manual, electrical diagrams with parts lists, hydraulic and lubrication diagrams. Serwema optionally offers: trial part milling in our factory, additional milling arbors, assembly and commissioning at your location, operator training and a control system upgrade to Sinumerik ONE. Spare parts and service come from a single source, worldwide, even after the purchase.

Condition: used, Year of construction: 2008, machine/vehicle number: 240-124, functionality: fully functional, pressing force: 160 t, stroke length: 800 mm, table width: 1,600 mm, table length: 1,200 mm, table height: 650 mm, total length: 1,900 mm, total width: 3,600 mm, total height: 3,300 mm, Equipment: documentation/manual, Hydraulic sub-platen press – 160 T – 1,200 × 1,600 mm For sale is a hydraulic sub-platen press from the manufacturer LÄPPLE with a maximum pressing force of 160 T. The machine has a table size of 1,200 × 1,600 mm, an open height of 1,050 mm, and a stroke of 800 mm, and is particularly suitable for forming, straightening, pressing, and assembly work in industrial applications. The press is equipped with a PILZ control system and has an electrical version for operation on a 3 × 400 V AC power supply. ##### Technical data + information: Hydraulic sub-platen press – 160 T – 1,200 × 1,600 mm ==== General information - Reference ID: TPT-07 - Manufacturer: LÄPPLE - Type: Hydraulic sub-platen press - Model: TV1600-50 - Machine number: 240-124 - Year of manufacture: 2008 - Pressing force: 160 T - Table size (working area): 1,200 × 1,600 mm - Table height: 650 mm - Open height: 1,050 mm - Stroke: 800 mm - Overall height: 3,300 mm - Overall width: 3,600 mm - Overall depth: 1,900 mm - Basement required: no ==== Hydraulic cylinder - Max. working pressure: 240 bar - Idle travel downwards: 10 mm/s - Idle travel upwards: 28 mm/s - Initial pressing speed: 10 mm/s ==== Hydraulics & drive - Main motor: 22 kW ==== Control system - Control system: PILZ - Control panel: on the frame - Electrical design: EPLAN 5.40 - Electrical documentation: wemascon Zeulenroda GmbH ==== Safety - Safety control system: PILZ - Light curtain / light barrier: available - Two-hand operation: available - CE-compliant design - Slug damping: no - Maintenance platform: no ==== Electrical connection - Main supply: 3 × 400 V AC Dcsdpfx Ais Ad Anteijp - Frequency: 50 Hz - Power supply: PE/N - Fuses: 63 A - Rated current of the system: 47 A - Control voltage: 24 V DC ##### Application areas: Forming, straightening, pressing, assembly work, toolmaking, mechanical engineering, metal processing, maintenance, pressing operations, series production (Hydraulic sub-platen press, sub-platen press, hydraulic press, LÄPPLE press, LÄPPLE TV1600-50, 160 T press, 160-ton press, forming press, straightening press, pressing press, assembly press, industrial press) Are you looking for a hydraulic press tailored to your specific application? Contact us for an individual offer. Our hydraulic presses are manufactured according to German Machinery Directive and European Machinery Directive (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements, as they comply with all points of the national Brazilian safety guideline NR 12, which is based on these. Our great strength lies in the design and manufacture of customized machines and press automation. We distribute tailor-made hydraulic presses at surprisingly favorable prices. For the hydraulics of the presses, components from leading European manufacturers are mainly used.

Condition: used, Year of construction: 1998, machine/vehicle number: 845, functionality: fully functional, pressing force: 106 t, stroke length: 1,000 mm, table width: 1,200 mm, table length: 1,700 mm, table height: 650 mm, total length: 1,965 mm, total width: 2,645 mm, total height: 3,992 mm, overall weight: 12,500 kg, Equipment: documentation/manual, Hydraulic 4-column stamping press – 106 T – 1,700 × 1,200 mm For sale is a hydraulic 4-column stamping press from the manufacturer ALN with a maximum pressing force of 106 T. The machine has a table size of 1,700 × 1,200 mm, an open height of 1,450 mm, and a stroke of 1,000 mm, making it suitable for stamping, forming, straightening, inserting, and assembly work in industrial applications. ##### Technical data + information: Hydraulic 4-column stamping press – 106 T – 1,700 × 1,200 mm ==== General information - Reference ID: TPT-09 - Manufacturer: ALN - Type: Hydraulic 4-column stamping press - Model: 4 SPY 60 SO - Machine number: 845 - Year of construction: 1998 - Pressing force: 106 T - Table size (usable area): 1,700 × 1,200 mm - Table height: 650 mm - Open height: 1,450 mm - Stroke: 1,000 mm - Overall height: 3,992 mm - Overall width: 2,645 mm - Overall depth: 1,965 mm - Total weight: 12.5 T - Basement required: no ==== Hydraulic cylinder - Max. working pressure: 243 bar - Return speed downwards: 250 mm/s - Return speed upwards: 280 mm/s - Initial pressing speed: 17.5 mm/s ==== Hydraulics & drive - Main motor: 25 kW - Oil tank: 650 l ==== Safety and equipment - Slug damping: yes - Maintenance platform: no ==== Documentation - Hydraulic diagram - Electrical diagram - Operating manual ##### Application areas: Stamping, forming, straightening, inserting, assembly work, toolmaking, mold making, metalworking, mechanical engineering, contract manufacturing, series production (Hydraulic 4-column stamping press, 4-column stamping press, hydraulic press, ALN press, 4 SPY 60 SO, 106 T press, 106-ton press, forming press, stamping press, straightening press, inserting press, assembly press, industrial press) Are you looking for a hydraulic press tailored to your specific application? Contact us for a customized offer. Our hydraulic presses are manufactured according to German and European Machinery Directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements, as they comply with all points of the national Brazilian safety guideline NR 12, which is based on these. Our great strength lies in the design and manufacture of custom machines and press automation. We distribute tailor-made hydraulic presses at surprisingly competitive prices. For the hydraulics of the presses, we mainly use components from leading European manufacturers. Dcsdpfx Aio Ad H S Aeisp

Condition: new, Year of construction: 2026, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, pressure: 75 bar, total height: 2,591 mm, total width: 2,438 mm, total length: 2,991 mm, temperature: 38 °C, operating pressure: 75 bar, energy consumption: 30 kWh, DESALINATION PLANT HF-RO: ULTRAFILTRATION AND REVERSE OSMOSIS ON A SKID The HF-RO combines hollow fiber ultrafiltration with seawater reverse osmosis. The ultrafiltration removes sediments, colloids, bacteria, and viruses and feeds the reverse osmosis directly, without an intermediate tank. This allows the system to process raw water that would quickly clog a conventional reverse osmosis system with cartridge filters: nearshore seawater, harbor water, river mouths, and water with highly variable turbidity. PERFORMANCE DATA (Design for 36,000 mg/l, 25 °C) - Inlet flow: 5.0 m³/h - Permeate flow: approx. 2.06 m³/h, approximately 48 m³/day with 24-hour operation - Inlet salinity: 250 to 43,000 mg/l (sea, brackish, and river water) - Inlet temperature: +2 to +33 °C - Inlet turbidity: up to 300 NTU, sediment up to 150 mg/l - Permeate: 150 to 500 mg/l, 300 to 1,000 µS/cm, retention rate 99.6% PROCESS 1. Disc filtration: 2 automatic disc filters 2" in duplex operation, 100 µm, backflushing with filtrate and compressed air during operation 2. Hollow fiber ultrafiltration: 4 modules, outside-in, 0.01 µm (100,000 Dalton), filtrate approx. 0.2 NTU, cyclic backflushing with air, the remaining modules continue to produce 3. Reverse osmosis: low-pulsation axial piston high-pressure pump (4.08 m³/h at 63 bar, motor 8.5 kW), 4 RO modules in GRP pressure pipes, max. 65 bar, automatic pressure and flow control Dedpfx Ao Ahqpgeiiocp CLEANING - integrated CIP for ultrafiltration and reverse osmosis - cleaning tank 2 x 100 l with 7.5 kW heater - 3 pneumatic dosing pumps for cleaning agents and chlorine - programmed disinfection, long-term preservation, and re-commissioning EQUIPMENT - materials: low-pressure ABS, high-pressure 1.4539 and 1.4410 super duplex, high-pressure pump 1.4462 duplex, tanks PP, frame stainless steel - valves in only two nominal sizes, interchangeable pumps, low variety of spare parts - PLC with 15.6" touch panel, Ethernet interface for remote monitoring - control of a frequency-controlled inlet pump - control cabinet 400 V / 50 Hz, approx. 18 to 20 kW, IP65 DIMENSIONS - main skid approx. 1,400 x 1,200 x 2,020 mm (L x W x H) - RO module stand approx. 600 x 550 x 1,990 mm APPLICATIONS Drinking and utility water for coastal and island supply, resorts and camps, desalination of harbor and river mouth water, process water for industry on the coast, emergency water supply, pilot operation for larger projects. SCOPE OF DELIVERY Main skid with disc filters, ultrafiltration, high-pressure pump, CIP system and control cabinet, RO module stand with 4 modules, internal piping and wiring, documentation (P&I, layout, process description). Not included in the scope of delivery (optional): inlet pump, compressed air supply, container housing, transport, installation, commissioning, training. NOTE We will confirm the binding performance after you provide your water analysis. Inspection and functional testing possible before purchase. Purchase or lease-purchase. English brochure available upon request.

Condition: used, Year of construction: 1998, pressing force: 100 t, For sale is a used die-setting press from the manufacturer REIS with a maximum pressing force of 100 tons. The machine has a table size of 1,100 × 800 mm, a maximum installation height of 950 mm, and numerous features, including an ejector in the table, oil connection boxes for core pulls, and a 180° pivoting ram plate. It is therefore particularly suitable for die-setting operations, tool try-out, and testing in mold and tool making. ##### Technical Data + Information: Die-setting press – 100 tons – 1,100 × 800 mm ==== General Information - Design: 4-column die-setting press - Manufacturer: REIS - Type: TUS 80–100 - Year of construction: 1998 - Pressing force: 26–100 tons (adjustable) - Retraction force max.: 45 tons - Table size: 1,100 × 800 mm - Max. table load: 5,000 kg - Installation height max.: 950 mm - Overall dimensions (W x D x H): approx. 2,100 × 3,395 × 3,670 mm - Total weight: approx. 8,500 kg - T-slots: DIN 650 – 22 mm Dcodpfx Aijxd Tiqeijp ==== Hydraulic Cylinder - Pressing force range: 26–100 tons - Retraction force: 45 tons ==== Hydraulics & Drive - Hydraulic pump: REXROTH SYDFE11x71RN0030CAM - Motor power: 7.5 kW - Working pressure max.: 200 bar - Pressure accuracy: ±5 bar - Tank volume: 200 l - Hydraulic oil: HLP 36 ==== Motion System - 180° pivoting ram plate - Load capacity of the pivoted ram plate: up to 3 tons - Ejector in the ram: 3.5 tons - Ejector stroke: 130 mm - Extendable table - Table can be tilted to both sides - Movable ejector in the table - Oil connection boxes for core pulls - Injection molding filling device in the ram - Quick clamping plate on the ram ==== Control - Operation via control panel - Press force setting - Operation of core pulls - Control: Siemens / Pilz - Digital measuring device ==== Safety - Industrial machine control - Operator panel with safety functions ==== Electrical Connection - Main supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz - Connection power main motor: 7.5 kW - Total connection power: 10 kW ##### Application areas: Die-setting, tool try-out, mold making, tool making, injection molding tools, automotive, prototype construction, trial tools, maintenance, production preparation (Die-setting press, try-out press, tool try-out press, hydraulic press, REIS TUS 100, 100 ton press, 4-column press, testing press, mold making press) Are you looking for a hydraulic press tailored to your specific application? Contact us for an individual offer. Our hydraulic presses are manufactured according to German and European Machinery Directives (Directive 2006/42/EC), EC standards and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements, as they comply with all points of the national Brazilian safety standard NR 12, which is based on these. Our core strength lies in special machine construction and press automation. We distribute customized hydraulic presses at surprisingly favorable prices. For the hydraulics of the presses, components from leading European manufacturers are mainly used.

Condition: used, Year of construction: 2014, Printing technology: FDM: build process using molten plastic Build volume X × Y × Z: 254 × 254 × 305 mm Layer thicknesses: 0.178 / 0.254 / 0.330 mm Model material: ABSplus P430 Support material: SR-30, soluble support material Material supply: Separate cartridges for model and support material Cartridge capacity: Approximately 922 cm³ per cartridge Network connection: Ethernet RJ45 Software: Stratasys Insight for print preparation Power supply (as per nameplate): 100–240 V, 12–6 A, 50–60 Hz Dedpfx Aie Ahklujiscp Product number: 163-00500

Condition: used, Year of construction: 2020, !! We are happy to advise you !! All systems are from 2020 or 2021 //// Used until 12/2021 7 x Domino printer 2 heads new price €4500 now €1900 Dedpfxsrlmwme Aiiscp 1 x Makroprint x8 printer with 8 heads new price €18,000 now €8000 3 x Makroprint x4 printer with 4 heads new price €10,000 now €4000 2x Makroprint X1 new €1250 1x Edding In Line €1000 4x Chinese and Italian system opinion German open to all HP cartridges piece with 4 heads €1500 A discount is possible for 2 devices!!!

Condition: new, Year of construction: 2025, Cartridges: 5 Dodpfx Aie Ahltzoiscp cartridge height [inch]: 30 cartridge type: code 7

Condition: excellent (used), Year of construction: 2015, Optimize your packaging line with a reliable, fully automatic case erector from market-leading SOCO SYSTEM, capable of erecting and bottom-taping up to 18 boxes per minute. This is a compact and high-performance industrial case erector designed for integration into automated packaging and logistics processes. The machine automatically retrieves flat corrugated cardboard boxes from the motorized magazine, erects the box, folds the bottom flaps, and seals the bottom with tape – ready for immediate filling. The machine is controlled via a user-friendly touchscreen interface from Proface and is built with reliable industrial components, including a Siemens PLC and Festo pneumatics, ensuring maximum uptime and easy maintenance. Dedj Ahg Ucepfx Aiiocp This 2015 unit is in excellent condition and offers a cost-effective automation investment with a short payback period compared to the new price. With its right-hand outlet configuration, it is ideally suited as a starting point before manual packing stations or directly connected to automatic conveyor systems. Available for immediate delivery. Shipping costs are additional.

Condition: good (used), Year of construction: 2003, machine/vehicle number: 694/0-302 (2003), functionality: fully functional, operating hours: 2,580 h, power: 12 kW (16.32 HP), workpiece height (max.): 48 mm, workpiece width (max.): 60 mm, edge thickness (max.): 15 mm, height adjustment type: electric, feed rate X-axis: 11 m/min, overall weight: 2,000 kg, Equipment: documentation/manual, Holzher Sprint 1417, year of manufacture 2003 - Only 160,000 linear meters run, very good condition - - Can also be operated separately without Ligmatech - - Ideal for high-quality furniture production, HPL and matte decors are no problem - Machine completely controlled by PLC, almost everything can be adjusted on the control panel, no defects, well-maintained machine used with expertise. Leuco Z3 jointing cutter installed, 2nd set of cutters available, various indexable inserts available. Board thickness max. approx. 48 mm, edge banding from 0.3-15 mm possible. Chain conveyor renewed approximately 10 years ago. Spray system for release and cleaning agents, controlled by demand. - Jointing fence motor-controlled and programmable. - Jointing cutters 1961, 2 x 2.0 kW - Glue system cartridge 1906, with sensing nozzle (important), cartridge magazine for 4 cartridges, color change easily possible, PU also possible. - Pressure unit 1903 MOT, pressure of the 1st and other rollers can be adjusted separately. - Miter saws 1918, bevel cuts adjustable. Dedpfx Ajz Dxh Nsiijcp - Flush trimming 1823 - Radius trimming 1942 MOT (one axis motor-adjustable for 1 and 2 mm edges, selectable on the control panel) - Profile trimming blade 2 mm 1929 pneumatically controlled. - Corner copying unit 1983 carbide-tipped, with adjustment on the control panel, functional, but needs to be fine-tuned again. - Flat trimming blade 1964 - Oscillating unit controlled by demand. Includes all operating manuals, documentation of the process steps digitally and in printed form by Holzher technicians. One set of DIA jointing cutters is included, as well as various indexable inserts for the cutting units. Return conveyor system ZHR 15 Boomerang, year of manufacture 1995. Mounted on the machine with coupling to the pressure bridge. Easily adjustable from the control panel, with rotating device for components. Adjusted to the feed rate, sensors still available from HOMAG. - Information without guarantee, the parties agree that the sale of the used machine takes place with complete exclusion of any warranty, guarantee and liability for defects. The buyer has inspected and tested the machine before purchase. - Sale only to commercial businesses, machine currently powered and in operation. Price negotiable. Machine available after clarification in December / January 2027. Crane loading or forklift loading also possible from an external warehouse.

Condition: good (used), Dust extraction fan, extraction, dust blower, extraction system, dust blower, dust extraction device, separator, welding fume filter, welding fume extraction, flue gas extraction fan, filter system Cartridge dust extraction system -Manufacturer: TEKA, filter system for extraction system including control unit with frequency converter -Type: ZPF9 Djdpszukp Ajfx Aiiocp -Cartridge filter: see photos -Inlet/Outlet: Ø640 mm / Ø640 mm -Extraction capacity: up to 20,000 m³/h -Note: A filter unit only, without a suction fan, can be supplied for an additional charge (ID38772) -Dimensions: 1840/1475/H2670 mm -Weight: 689 kg

Condition: used, Year of construction: 2016, Format: 1250 x 2500 mm Equipment: Dcsdpfxoyx Hu Se Aiisp Number of ink cartridges: 8 Color channels: 8 Number of printheads: 16 Type of input current: Alternating current (AC) Total weight: 1,410 kg