Used Lead Cartridge for sale (1,753)

Condition: as good as new (ex-display), Year of construction: 2025, machine/vehicle number: 2561, functionality: fully functional, power: 5.5 kW (7.48 HP), input voltage: 400 V, input current: 11 A, input frequency: 50 Hz, type of input current: three-phase, Equipment: CE marking, documentation/manual, Panel saw Lead MJ-45TB, manufactured in 2025. Sliding table 3200 x 405 mm, motor power 5.5 kW + 1.1 kW, main saw speed 3000 / 4000 / 5000 rpm, scoring saw speed 9000 rpm. Maximum cutting height 120 mm (90 degrees) and 75 mm (45 degrees). Saw blades 315 x 30 mm and 120 x 20 mm, automatic lifting and manual tilting, large extraction hood. 400 V / 50 Hz three-phase connection, CE version. Dodpfxez Ngi Ts Aiiscp

Condition: used, functionality: fully functional, type of input current: three-phase, input voltage: 400 V, filter area: 324 m², suction capacity: 18,000 m³/h, negative pressure: 2,250 Pa, input frequency: 50 Hz, Dust extraction, filtration, welding fume extraction, self-cleaning cartridge filter, pneumatic, vacuum-based TEKA AIRTECH P18. The main areas of application for these systems are industrial plants/welding shops where it is not possible to implement point extraction or where point extraction is not sufficient to maintain clean air in the workshop. Dcsdo Ahm Iispfx Aiijp Laterally mounted ducts with a pollution collection point draw in contaminated air and lead it to the filtration section. Here, pollutants in the form of fine particles accumulate on the surface of the cartridge filter. A compressed air pulse is applied to clean the cartridge filters automatically at the required intervals. After the compressed air pulse, the particles collected on the filter surface detach and fall into the dust collection tank. The cleaned air returns to the work area through individually adjustable long-range nozzles. At the same time, the outlet of the cleaned air directs the contaminated air in the workshop towards the extraction ducts. The filter is cleaned by a microprocessor controller with compressed air pulses during operation, resulting in high device efficiency. Low compressed air consumption thanks to the "Power-Spray" system. The AIRTECH series of devices is certified by IFA according to EN ISO 15012-1 or DIN EN ISO 21904-1/-2 and approved for welding fume class W3 as a stationary, local welding fume extraction unit. Parameters: Capacity - 18,000 m3/h Motor power - 11 kW Vacuum - 2250 Pa Filtration area - 324 m2 (9 filter cartridges of 36 m2 each) Fan in a sound-absorbing housing Control cabinet with electrical documentation Noise level - 72 dB Dimensions: Height - 5.00 m Base width - 1.44 m x 1.44 m Width with outlet ducts - 8.5 m Total weight approximately 2400 kg

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: 844 12 64, turning diameter over cross slide: 215 mm, spindle bore: 40 mm, turning diameter: 380 mm, center height: 190 mm, center width: 1,250 mm, quill stroke: 120 mm, total length: 3,020 mm, total width: 950 mm, total height: 1,500 mm, spindle speed (max.): 2,800 rpm, spindle speed (min.): 14 rpm, overall weight: 1,850 kg, quill mount: MK 3, workpiece weight (max.): 300 kg, Trade show lathe, available from stock. After Trens filed for bankruptcy, we made an effort and had TOS and later Trens lathes completely overhauled. All machines were disassembled down to the last screw. Here is a run-through of a general overhaul at our company: 1. Machine cleaning, disassembly of the individual machine components 2. Grinding: bed, slide, cross support, spindle, tailstock quill 3. Grinding + scraping of the upper support guideways, replacement: trapezoidal screw with nut and V-ledge 4. Scraping of the guide surfaces: spindle, slide, cross support, and tailstock to geometric positions according to the accuracy report 5. Replacement: screw with nut, V-ledge, and Multifix base body for the cross support (including 2 turning tool cartridges) 6. Complete disassembly and replacement of the necessary spare parts in the lock case, threaded housing, headstock, gear box, tailstock, cross support, and upper support 7. Installation, replacement if necessary, of racks, repair of the lead screw and feed screw 8. Complete bearing replacement in all machine assemblies 9. Complete replacement of machine plates 10. Priming of the machine, sealing, sanding, polyurethane topcoat, and painting of the machine accessories - white RAL 9003, anthracite RAL 7016 11. New control cabinet with electrical components, replacement: main motor, rapid traverse motor, hydraulic pump, cabling, and LED lighting of the work area 12. Preparation of the accuracy report and the electrical test report 13. Inspection and machine acceptance at the factory All refurbished machines have a CE certificate and a 12-month warranty. CE version: Dcsdpev Hzqxsfx Aiijp - Chuck guard with limit switch - Front chip guard mounted on slide - Rear chip guard - Lead screw and feed screw covers - Brakes after emergency stop within 2 seconds Special accessories (used): - Three-jaw lathe chuck Ø 190 mm - Four-jaw lathe chuck Ø 190 mm - Three-jaw lathe chuck Ø 240 mm - Four-jaw faceplate Ø 320 mm - Support center for bed slide - Various chuck jaws (10 pieces) - Collet set Ø 2 - 25 mm with collet chuck + drawbar - Special collet set (10 pieces) with collet chuck - 4-way tool holder

Condition: excellent (used), Year of construction: 2008, operating hours: 2,483 h, functionality: fully functional, machine/vehicle number: 8015, travel distance X-axis: 1,200 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 600 mm, controller model: Heidenhain iTNC 530, spindle speed (max.): 12,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 1,200 mm Travel range, Y-axis: 600 mm Travel range, Z-axis: 600 mm Rapid traverse rate X/Y: 30 m/min Rapid traverse rate Z: 24 m/min Table size: 1,300 × 600 mm Spindle speed: 50–12,000 rpm Dcsdpfxo Aggibs Aiijp Spindle power: 21 / 15 kW Tool holder: BT40 Spindle drive: direct drive Tool positions: 40 Tool change time: approx. 4 s Tool changer: dual gripper MACHINE DETAILS Coolant pressure: 20 bar CNC control: Heidenhain iTNC 530 Screen diagonal: 15 inches Operating voltage: 400 V Connected power: 25 kVA Mains frequency: 50/60 Hz Number of phases: 3 Machine weight: approx. 7,500 kg Operating hours Spindle hours: 2,483 h Machine operating hours: 14,198 h Control operating hours: 65,193 h EQUIPMENT Automatic tool changer with dual gripper Internal cooling through the spindle (IKZ), Form A High-pressure coolant system Additional coolant tank Two switchable filter cartridges Chip conveyor parallel to the X-axis Three-color signal light (red/yellow/green) Fully enclosed work area Work area lighting Machine documentation Toolbox Alignment screws and washers CE specification

Condition: like new (used), Year of construction: 2025, operating hours: 200 h, functionality: fully functional, workpiece weight (max.): 4,000 kg, table length: 14,000 mm, Equipment: documentation/manual, FOR SALE: Voortman MO Compact 900 — 6-Axis CNC Pipe Plasma Cutting Machine (2025) Manufacturer: Voortman Steel Machinery / Müller Opladen GmbH Dcedpfx Aijy H I Trjiep Model: MO Compact 900 Year of commissioning: 2025 Condition: Demo machine — under 200 production hours, virtually factory new Type: CNC plasma PIPE profiling machine (6-axis) - no beams Category: Plasma cutter / Pipe cutting machine Machine description: This Voortman MO Compact 900 is a 6-axis CNC pipe cutting machine capable of processing round pipes up to 914 mm in diameter and 12,000 mm in length, with wall thicknesses ranging from 3 to 50 mm. The machine was installed in 2025 in Belgium and has logged fewer than 200 production hours — making it virtually a new machine at a pre-owned price. The 6th CNC axis maintains a constant torch-to-material distance, ensuring flawless weld preparations and bevel cuts up to ±45°. The proprietary 3D Azimuth cutting head allows torch adjustment of ±60° and 380° rotation for precise contour cutting on any pipe geometry. Included equipment: — Voortman MO Compact 900 pipe profiling machine (6 CNC axes with x-rail, truck, column, and cutting unit) — Hypertherm MAXPRO200 plasma source (200 A, 100% duty cycle, manual gas console) — 3D Azimuth cutting head with intelligent torch positioning for x-, y-, and v-weld preparations — Electromechanical tracer arm for continuous pipe circularity measurement — Self-centering three-jaw chuck (1,200 Nm torque) — Pipe conveyor transport system on rail — Two-point fume extraction (at cutting head and through chuck) — Voortman Filter Unit ECO6/HCS with Donaldson Ultra-Web® cartridge technology and spark arrestor — E-cabinet with CNC unit, PLC, IP54 enclosure, power buffer — Industrial PC with 22" touchscreen and mobile control panel — All safety devices (CE certified per 2006/42/CE and 2004/108/CE) — Full technical documentation, operator manuals, installation drawings Key specifications: — Clamping range: 50 – 914 mm — Max pipe length: 12,000 mm — Max pipe weight: 4,000 kg (with pipe carriages) — Plasma bevel range: +45° / −45° — Cutting capacity: 3 – 50 mm (mild steel) — Pierce capacity: 32 mm — Chuck rotation speed: 0 – 10 rpm — Torch carriage speed: 0 – 15,000 mm/min — Installation footprint: 7.0 × 4.0 × 4.0 m — Machine weight: 6,000 kg Please note: COROBS machine control software licenses are not included and must be purchased separately from Voortman. Voortman can provide reinstallation, commissioning, operator training, and ongoing maintenance contracts at the buyer's facility. Why buy this machine? A new MO Compact 900 currently costs EUR 350,000+ and has a lead time of 6–12 months. This unit offers the same capability with immediate availability and significant savings. Full OEM support from Voortman is available for the buyer. Location: Belgium (available for inspection by appointment) Delivery: Ex-works. Dismantling and transport by agreement. For questions or further information, please send us a message or call us.

Condition: excellent (used), Stainless steel ice cube machine 220 V 75 kg/day, nuggets, 32 kg storage container, air cooling 640 x 600 x 800 mm (W x D x H) Includes Britta water filter Purity 1200 Steam These filter cartridges reduce the carbonate hardness in tap water, thus preventing limescale deposits in the machine. Dcjdpfx Ae Ab E Sveiijp In addition, heavy metal ions such as lead and copper, turbidity, organic contaminants, and other odor-causing substances such as chlorine residues are filtered out.

Condition: ready for operation (used), Year of construction: 2018, L&Z Lathe / DMTG - Dalian CW6163E / 5 - Meter Turning Length -Year of manufacture: 2018 -CE marking -Turning diameter over bed: 630mm -Turning diameter over cross slide: 350mm -CENTER DISTANCE: 5000 mm -Spindle bore: 100mm -Bed width: 550mm -Spindle nose: C11 -Spindle speeds: 7.5 - 1000 RPM -Number of speed steps: 18 -Automatic longitudinal / crossfeed -Rapid traverse in bed slide / longitudinal & crossfeed -Thread cutting / Metric / Inch / Module etc. -Main drive: 11 KW -Tailstock quill diameter: 100mm -Tailstock quill stroke: 250mm -Coolant system -3-jaw chuck: 300mm -2 x Steady rests -Chuck guard Dcodpfx Aio Ah E I Hoijp Dimensions: L x W x H: 7.4 x 1.4 x 1.6 meters / Weight: 6700 KG Errors and omissions excepted.

Condition: ready for operation (used), functionality: fully functional, L&Z Lathe MONDIALE GALLIC 16 N / 3 - 3-Axis Digital Readout ACU-RITE -Center height 165mm -Swinging diameter over bed 330mm -Distance between centers 1000mm -Spindle bore approx. 45mm -Three-axis digital readout ACU-RITE -Speed range (geared) 45 - 2000 RPM -Automatic longitudinal / cross feeds -Thread cutting, metric / inch, etc. -Quick-change tool holder -Tailstock MK 4 -Three-jaw chuck -Electric chuck guard Dcede Ah T Sbepfx Aiijp -Chip guard -Drill chuck & traveling center -Documentation Dimensions: L x W x H 2.1 x 1.2 x 1.6 meters / Weight 1700 KG Errors and omissions excepted.

Condition: new, Year of construction: 2022, functionality: fully functional, NEW Grundfos Pump CRN 10-12 A-FGJ-G-E-HQQE | Stainless Steel AISI 316 | 4 kW Condition: Brand new, never used. Model: CRN 10-12 A-FGJ-G-E-HQQE Manufacturer: Grundfos (Leading pump solutions provider) DEVICE DESCRIPTION The item for sale is a high-performance, vertical multistage centrifugal pump from the CRN series. This is a version made entirely from acid-resistant stainless steel (AISI 316), setting it apart from the standard cast iron models (CR). It is designed for operation in the most demanding industrial conditions, ensuring reliability when handling aggressive and demanding liquids. The pump is an ideal solution for businesses seeking a high-efficiency device, ready for immediate installation in water treatment systems, technological processes, or high-pressure setups. _____ KEY TECHNICAL DATA • Rated flow: 10 m3/h • Rated head: approx. 96.7 m (max up to 122 m) • Motor power: 4 kW • Power supply: 3-phase Dcjdpfxjx Im Aho Aiisp • Rotational speed: 2900 rpm • Maximum operating pressure: 25 bar • Liquid temperature range: -20°C to +120°C • Number of impellers: 12 • Year of manufacture: 2022 CONSTRUCTION AND MATERIALS • Material configuration (G): All liquid-contacting parts are made from stainless steel EN 1.4401 / AISI 316 (providing maximum corrosion resistance). • Shaft seal (HQQE): Durable cartridge mechanical seal made from silicon carbide (SiC/SiC) with EPDM elastomers. Guarantees longevity and leak-tight operation even with hot water. • Connection (FGJ): Universal flanged system (DIN/ANSI/JIS), allowing easy adaptation in existing installations. _____ APPLICATIONS Thanks to its acid-resistant construction, the CRN pump is suitable for: 1. Chemical and pharmaceutical industries (pumping acids, alkalis, aggressive media). 2. Filtration and water treatment systems (reverse osmosis, ultrafiltration). 3. Industrial washing systems and CIP/SIP cleaning setups. 4. Process water installations in brewing, dairy, and food industry. _____ WHY BUY THIS PUMP? • Premium product: The CRN series is the “Mercedes” among vertical pumps. • Time-saving: Device is available immediately (no long lead times from the manufacturer). • No usage marks: The pump is brand new, properly stored, and ready to operate at full capacity. Important: Please verify that the electrical and hydraulic parameters match your project requirements before purchase.

Condition: used, Candles: 12 cartridge height [inch]: 30 Dedpfx Aio Ahld Toijcp cartridge type: code 41 with fin end, 3 locking tab ext 222 O-ring closure: parrotlip Fittings: draining outlet, manometer, deaeration

Condition: new, IPETRONIK Type: Interior Climate Simulation Box Technical data and description of the system: IPETRONIK Interior Climate Simulation Box (new and unused) The interior climate simulation box is designed to simulate the passenger compartment for testing in a recirculated air mode. It has a variable interior volume of 1.8 to 4 m³. The exhaust air volume flow from the front evaporator or the air conditioning unit is regulated and fed into the interior. The interior climate simulation box is used to test only rear evaporators installed in the passenger compartment. The insulating housing is mounted on an aluminum profile frame with rollers. A light is installed in the chamber. The box is protected against overtemperature by a safety thermostat (Esti). If the permissible temperature is exceeded, a glass cartridge in the ESTI is destroyed. The system is stopped. (TRIGGER TEMPERATURE: 80°C) Technical data of the insulating chamber: Dimensions: External: Width 1,860 mm Depth 2,360 mm Height 1,360 mm Internal: Width 1,700 mm Depth 2,200 mm Height 1,200 mm Insulation: 80 mm polyurethane rigid foam, CFC-free, U-value 0.27 W/m2K, building material class B1 according to DIN 4102 Technical data and description of the system: Connection: Tongue-and-groove system with embedded eccentric locking catches. Surfaces: Both sides: 0.8 mm stainless steel sheet 1.4301, ground, grit 320 Floor design: 2.0 mm stainless steel sheet 1.4301, SM diamond pattern, non-slip, Floor with a 90° upturned edge around the perimeter (approx. 15 mm), floor sheet flush with the wall sheet, Pressure distribution plate made of laminated wood, can withstand a load of 1,500 N/rubber wheel (contact area > 4 cm2), 30,000 N/m2 surface load, floor joints completely welded, welded stainless steel pipe as a floor drain, leading downwards through the floor Chamber door: Hatch door, 1-leaf, 800 x 1200 mm i.L., DIN left, heated door frame (230 V), Heater tapes silicone-free, 4-sided sealing profile made of EPDM, Latch closure, lockable, emergency release, heated viewing window, 500 x 500 mm, 3-pane glazed, surface heating (230 V), frame heating (230 V), heating controlled externally, silicone-free edging Sliding wall: Dcsdpszd Ukpsfx Aiiep 1680 x 1180 mm, 80 mm polyurethane rigid foam, 0.8 mm stainless steel sheet 1.4301 on both sides, ground, grit 320, with protective film, closed with sheet metal on the reverse side (The rear wall can be adjusted manually and continuously to change the volume) Recirculation system: A heat exchanger (Systemair) for indirect temperature control is installed in the recirculation circuit for temperature control. The air is conveyed via a radial duct fan (Cosmo); heating is provided by an electric heater (Türk und Hillinger) integrated into the brine circuit. The heaters are continuously monitored by temperature monitors and limiters (Türk und Hillinger, Johnsson Controls). Cooling is provided by a secondary brine circuit with pumps (KSB) and a 3-way valve (Belimo). Installed electrical heating power 1 * 6kW. The mixing ratio is 50% water / 50% ethylene glycol. Power supply from station: =TME2++AS-QF21 Operating voltage: 400V Power: 17kW Rated current: 33A Fuse: 35A Control voltage: 24V DC /24V AC /230V AC PLC system: S7 300 Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions by telephone.

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, L & Z spindle lathe / WEILER CONDOR B / incl. Heidenhain 3-axis digital control - Machine from an educational institution / in perfect condition - Three-axis Heidenhain digital control Dcedoz St Iuopfx Aiijp - Center height 165 mm - Swing over bed 330 mm - Swing over cross slide 185 mm - Turning length approx. 800 mm - Spindle speeds (geared) 22 - 2800 rpm - Thread cutting / Metric / Inch, etc. - Bar capacity 40 mm - Tailstock / Morse taper MK 3 - Electric chuck guard - Multifix base holder with inserts - Three-jaw chuck Forkardt - Machine lamp - Chip guard - Bed stop - Machine feet - Documentation Dimensions: L x W x H 1.8 x 0.8 x 1.6 meters / Weight 1100 kg Errors and omissions excepted.

Condition: new, Year of construction: 2025, TPO0909E powder coating oven Working dimensions (mm): 900 (W) x 900 (D) x 1600 (H) SPECIFICATION: * Power consumption: 9 kW. Equipment: * Rod for hanging details * Convection (Equal temperatures throughout the oven), * Locks for safe opening and closing, * Maximum operating temperature: 230°C. TQ0906 powder coating booth Working dimensions (mm): 900 (W) x 600 (D) x 1400 (H) SPECIFICATION: * Power consumption: 1,6kW * Air capacity: 3200m3/h, * Hermetic lamp: 1pcs. * Automatic filter cleaning system * The cabin is equipped with a set of pneumatic quick connectors * Cartridge filter: 1 pcs * Paint recovery container Oven, cabin in stock, ready for shipment. Dsdpfx Asfgnytoiijcp CHOOSE BUMEX SP. Z O.O. Very high quality of the machines offered on the market. Professional advice and service. Warranty. Warranty and post-warranty service. Full technical documentation. 100% satisfaction of our clients. All products of the brand BUMEX SP. Z O.O. have WE certificate. We offer our own transport - prices are agreed each time for a given offer. We issue VAT invoices. Short lead times! Possibility to order machines in various, personalized configurations and dimensions. Please do not hesitate to contact us.

Year of construction: 2000, condition: used, Year of manufacture: Dec 2000 New: No Serial number: 385/65 R 22.5 Dedpfsx Ahkasx Aiiscp NETTE TRAILER TIRES.

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, L&Z Lathe KMUTH BASIC Plus incl. 3-axis digital display - Year of manufacture 2011 - CE marking - Three-axis digital display - Center height 150mm - Max. turning diameter 300mm - Max. turning diameter over support 178mm - Max. turning diameter without bridge 430mm - Center distance 810mm - Spindle bore 38mm - Spindle speeds (geared) 60 - 1550 rpm (9 steps) - Automatic longitudinal / facing feeds - Spindle mount - Camlock D1 - 4" - Tailstock taper MK 3 Dsdpfx Aez Hwx Eoiiocp - Quill travel 100mm - Bed width 180mm - Multifix base with insert - Electric chuck guard - Work light - Coaxial center - 3-jaw chuck - 2 x steady rests - Documentation Dimensions: L x W x H 1.6 x 0.7 x 1.6 meters / Weight 550 kg Errors and omissions excepted.

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, L & Z Lathe WEILER CONDOR B incl. three-axis digital display -CE marking -Machine from an educational institution / very well maintained -Center height 165mm -Swinging diameter over bed 330mm -Swinging diameter over cross slide 185mm -Turning length 800mm -Spindle speeds 22 - 2800 rpm -Automatic / longitudinal and cross feeds -Threading / metric / inch, etc. -Bar capacity 40mm Dsdszvx A Tspfx Aiiecp -Tailstock / Morse taper MT3 -Multifix base and inserts -Three-jaw chuck 200mm -Electric chuck guard -Spindle cover -2x Emergency stop -Coolant system -Chip guard -Documentation Dimensions: L x W x H 1.8 x 0.8 x 1.6 meters / Weight 1200 kg Errors and omissions excepted.

Condition: used, Year of construction: 2006, functionality: fully functional, Equipment: rotational speed infinitely variable, Manufacturer: 600 Lathes Model: Harrison V350 Centre Height: 170 mm Swing over Bed: 350 mm Swing over Cross Slide: 196 mm Swing in Gap: 535 mm Width in front of Face Plate: 165 mm Distance between Centres: 650 mm Spindle Speeds (stepless via potentiometer across 3 ranges, with digital readout): Dcjdpfx Asxcuuleiisp 15 - 340 rpm 45 - 1010 rpm 150 - 3250 rpm Spindle Mount (Camlock): D1-4 Spindle Bore: 54 mm Spindle Motor: 7.5 kW Carriage Guideway Width: 318 mm Cross Slide Travel: 250 mm Top Slide Travel: 140 mm Tailstock Quill Travel: 140 mm Tailstock Quill Taper: MT4 Quill Diameter: 63 mm Metric Version Machine Threads: Metric: 0.2 - 14 mm (51) Imperial TPI: 2 - 56 (56) Module: 0.2 - 3.5 (20) Diametral Pitch: 8 - 56 (20) Drive Power: 7.5 kW Equipment: 3-Axis Digital Readout 3-jaw Chuck Röhm D:200 mm 4-jaw Chuck D:160 mm Collet Chuck System Steady Rest 4-position Quick Change Toolpost Live Centre Chuck Guard Additional Chip Shield on Carriage Coolant System Rear Splash Guard Machine Documentation incl. Schematics Dimensions: Floor to Spindle Centre: 1050 mm Overall Length: 1900 mm Overall Width: 1100 mm Overall Height: 1300 mm Weight: 1350 kg The machine can be demonstrated under power on site by arrangement. All details without guarantee. Errors and prior sale reserved.

Condition: used, Year of construction: 1979, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS Working area Swinging diameter over bed: 480 mm Swinging diameter over cross slide: 200 mm Turning length: 650 mm Maximum turning diameter over bed cover: 200 mm Distance between centers: 750 mm Spindle Spindle head: Size 6 Spindle bore: 58 mm Control CNC path control: 2 axes Control system: Siemens SINUMERIK 5T Threading: available Motor control cabinet: Siemens 810T Tailstock Taper in tailstock quill: MK 4 Tailstock quill travel: max. 200 mm Tailstock travel: 550 mm Performance data Total power requirement: 18 kW Dcsdpe Aa Nauofx Aiiop Machine weight: approx. 2.7 t Machine dimensions Space requirement: approx. 2.70 × 1.58 × 1.68 m Control cabinet Control cabinet dimensions: 800 × 400 × 2,300 mm Control cabinet weight: 150 kg Motor control cabinet dimensions: 800 × 900 × 1,000 mm Motor control cabinet weight: 200 kg EQUIPMENT 4 chucks Spax screws Sheet metal screwdriver Drill Drill bits

Condition: used, Year of construction: 2007, functionality: fully functional, power: 20 kW (27.19 HP), input voltage: 415 V, input current: 50 A, input frequency: 50 Hz, type of input current: three-phase, workpiece length (max.): 2,500 mm, workpiece width (max.): 1,000 mm, workpiece height (max.): 80 mm, Equipment: documentation/manual, We offer this used WEEKE OPTIMAT BHX 500 throughfeed machining center, year of construction 2007. The Homag Weeke Optimat BHX 500 is a compact CNC Horizontal drilling centre designed for high-precision processing of furniture panels, cabinet parts, and joinery components. Its horizontal machining design allows efficient processing with minimal floor space while maintaining high production speed and accuracy. _____ Key Features • Horizontal CNC drilling centre for efficient panel processing • Large processing capability • High-speed axis movement for fast production cycles • Integrated clamping system for precise panel positioning • Designed for drilling, routing, and grooving operations • Built by HOMAG / Weeke, a leading manufacturer of CNC woodworking machinery _____ Axis Speeds • X axis speed: up to 138 m/min • Y axis speed: up to 80 m/min • Z axis speed: up to 50 m/min • Pressure plate axis: 27 m/min Djdpeyr Utnjfx Aiiocp _____ Workpiece Dimensions • Length: Min 300 max 2500mm • Width: Min 100 max 1000mm • Thickness: Min 4 max 80mm _____ Machine Dimensions • Length: approx. 6500 mm • Width: approx. 2300 mm • Height: approx. 2700 mm _____ Electrical Requirements • Operating voltage: 3 × 415 V ±5% • Frequency: 50 Hz • Total connected load: approx. 19.5 kW • Recommended fuse protection: 50 A _____ Pneumatic Requirements • Compressed air pressure: minimum 7 bar • Air consumption: approx. 2500 NL/min _____ Dust Extraction • Dust extraction connection: 2 × 280 mm ports • Airflow requirement: minimum 4450 m³/h • Vacuum pressure: approx. 3000 Pa _____ If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: used, Year of construction: 1972, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS General Information Manufacturer: PBR Type: TM 450/2000 Machine Type: Precision draw and feed spindle lathe Machine Weight: approx. 7.9 t Working Area Turning diameter over bed: 980 mm Turning diameter over carriage: 600 mm Turning length: 2,200 mm Turning diameter in the pit: 1,200 mm Pit length: 450 mm Spindle Spindle bore: 150 mm Speed stages: 24 Speed range: 8–800 rpm Axes and Travels X-axis: 2,000 mm X²-axis: 350 mm Y-axis: 500 mm Feeds Feed stages: 108 Longitudinal feed: 0.032–15.2 mm/rev Cross feed: 0.016–7.6 mm/rev Thread Cutting Number of thread pitches: 398 Metric thread pitch: 0.5–224 mm Metric thread pitch: 0.25–112 mm Imperial thread pitch: 56–1/8 TPI Diametral Pitch: 112–1/4 D.P. Tailstock Arbor support: MK 6 Dsdpj Aa Azljfx Aiijcp Arbor travel: 380 mm Electrical Data Voltage: 380 V Frequency: 50 Hz Total power requirement: 25 hp Dimensions Footprint: approx. 4.4 × 1.8 × 1.7 m EQUIPMENT Original Forkardt 3-jaw chuck, 500 mm Hardened and ground bed guides Rapid traverse for longitudinal and cross feeds Spindle brake Original Sauter hydraulics with external oil supply Original Ideal tool holder Faceplate with 4 independent jaws Coolant system Magnetic clutch Automatic longitudinal stops Cross stop Thread dial Reducing sleeve 2 fixed centers Fixed steady rest Swiveling Staudacher spindle guard with safety switch 2 emergency stop buttons Main switch Chip collector Workpiece lighting Machine-mounted control cabinet

Condition: ready for operation (used), functionality: fully functional, L & Z Lathe WEILER Matador -Center height 140mm -Distance between centers 500mm Dodpjz Nltdsfx Aiijcp -Speed range (continuously variable speed adjustment) 25-3000 RPM -Spindle bore approx. 36mm -Automatic longitudinal and cross feeds -Thread cutting / Metric / Inch, etc. -Tailstock / Morse taper MK3 -Electric chuck guard -Multifix with insert -Three-jaw chuck with interchangeable jaws -Machine feet -Change gears -Drill chuck & rotating center -Documentation Dimensions: L x W x H 1.5 x 0.6 x 1.2 meters / Weight approx. 600 kg Errors and omissions excepted.

Condition: used, machine/vehicle number: 3045, No minimum price – guaranteed sale to the highest bidder! Loading: December 1st to December 10th. TECHNICAL DETAILS General Information Manufacturer: Matra Model: MD40 Machine Type: Pull and lead spindle lathe Machine Weight: approx. 4.8 t Working Area Turning diameter over bed: 870 mm Turning diameter over carriage: 520 mm Turning length: 2,100 mm Turning diameter in the pit: 1,080 mm Pit length: 430 mm Spindle Speed stages: 24 Speed range: 8–1,000 rpm Spindle bore: 103 mm Slides and Travels X-axis: 1,830 mm X²-axis: 160 mm Y-axis: 415 mm Compound slide travel: 450 mm Top slide travel: 160 mm Feeds Longitudinal feed stages: 104 Longitudinal feed: 0.1–61.6 mm/rev Longitudinal feed: 0.0038–2 19/64 in/rev Cross feed stages: 104 Cross slide feed: 0.3–18.4 mm/rev Cross feed: 0.0012–47/64 in/rev Rapid traverse longitudinal: 5,140 mm/min Rapid traverse cross: 2,570 mm/min Thread Cutting Thread pitches: 72 Metric thread pitch: 0.5–240 mm Inch thread: 60–1/8 threads/inch Module thread: 0.125–60 mm Tailstock Tailstock cross travel from center: 10 mm Arbor mount: MK 6 Arbor stroke: 280 mm Electrical Data Frequency: 50 Hz Operating voltage: 380 V Control voltage: 220 V Rated current: 30 A Fuse rating: 50 A Total power consumption: 13 kW Dimensions Footprint: approx. 4.1 × 1.5 × 1.9 m EQUIPMENT Original Forkardt F400 3-jaw chuck Dsds Aa Az Sopfx Aiijcp Removable bridge Original MiniWizard 2-axis digital display 3 glass scales Multifix quick-change tool holder Swiveling spindle guard with safety switch 2 safety emergency stop buttons Lockable main switch Important note: The machine vises and the steady rest visible in the pictures are not included in the scope of sale and delivery!

Condition: used, functionality: fully functional, machine/vehicle number: P15176, Year of construction: 2014, operating hours: 11,531 h, total length: 838 mm, total height: 1,143 mm, total width: 737 mm, type of input current: AC, overall weight: 148 kg, input voltage: 240 V, input current: 6 A, input frequency: 50 Hz, ambient temperature (min.): 15 °C, ambient temperature (max.): 30 °C, electrical fuse: 13 A, feed length X-axis: 254 mm, feed length Y-axis: 254 mm, feed length Z-axis: 305 mm, Stratasys Fortus 250mc FDM 3D Printer – 2014 | Fully Maintained | Complete System The machine has been fully maintained by SYS Systems UK. Last calibrated 26/1/26. Last print was run on 24/11/25. Operating hours 11,531 h Manufacturer: Stratasys Model: Fortus 250mc Manufactured: 2014 Technology: FDM (Fused Deposition Modelling) Condition: Used Maintenance: Fully maintained by SYS Systems UK - Fans, Motion belts and ducting recently renewed. Build volume: 254 × 254 × 305 mm Layer thickness: 0.178,0.254,0.330 mm Included: Various Nozzles, Build Plates, ABS and Support material cartridges, Open materials chip re-programmer kit, Custom enhanced purge bin and purge shelf kit. Printer can be viewed. Location: Available for inspection by appointment. Dcodpfxs Ah R T Re Aiiep Sold ex-works. The printer and associated equipment are sold from their current location. The buyer is solely responsible for dismantling, removal, loading, transportation, shipping and installation at the destination. The buyer is also responsible for arranging any specialist lifting, transport or installation requirements. Buyers are strongly encouraged to inspect the equipment and assess access, lifting and transportation requirements before purchase. Also available, support removal soak box for post processing water soluble support material. ask for more details.

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, L & Z lathe / WEILER CONDOR AC / Stepless speed control / FROM AN EDUCATIONAL INSTITUTION - CE marking - Year of manufacture: 2000 - Swing over cross slide: 180 mm - Distance between centers: 165 mm - Max. swing: 330 mm - Turning length: approx. 800 mm - Speed (stepless): max. 2800 rpm - Automatic longitudinal / cross feeds - Threading / Metric / Inch etc. - 3-jaw chuck - Tailstock - Chip guard - Machine light Dsdpfx Aijz Izi Djiecp - Multifix base and 6 inserts - Various change gears - Coolant system - Various operating tools - Documentation Dimensions: L x W x H: 1.8 x 1 x 1.8 meters / Weight: 1300 kg Errors and omissions excepted.

Condition: used, functionality: fully functional, machine/vehicle number: L0290, Year of construction: 2014, operating hours: 26,052 h, total length: 2,771 mm, total height: 2,281 mm, total width: 1,684 mm, type of input current: three-phase, overall weight: 2,869 kg, input voltage: 230 V, input current: 34 A, compressed air connection: 7 bar, input frequency: 50 Hz, ambient temperature (min.): 15 °C, ambient temperature (max.): 29 °C, positioning accuracy: 0.089 mm, electrical fuse: 40 A, feed length X-axis: 914 mm, feed length Y-axis: 610 mm, feed length Z-axis: 914 mm, power: 13.5 kW (18.35 HP), space requirement length: 4,210 mm, space requirement height: 2,941 mm, space requirement width: 3,573 mm, Stratasys Fortus 900mc – 2014 | Fully Maintained | Complete System The machine has been fully maintained by SYS Systems UK. Last calibrated 16/7/26. Last print was run on 14/10/26. Dcsdpfe Ah Snkox Aiijp Manufacturer: Stratasys Model: Fortus 900mc Manufactured: 2014 Technology: FDM (Fused Deposition Modeling) Condition: Used Maintenance: Fully maintained by SYS Systems UK - Updated to Gen2 Plus spec in 15/1/2025. Build volume: 914 × 610 × 914 mm Layer thickness: 0.127,0.178,0.254,0.330,0.508 mm Material License Included: ABS-M30, ABS M30i, ABSi, ABS-ESD7, ASA, Nylon 6, Nylon 12, PC, PC-ABS, PC-ISO, PPSF, ST-130, Ultem 9085, Ultem 9085 CG, Ultem 1010, Ultem 1010-CG Included: Various Nozzles, Build sheets, model and Support material cartridges. Printer can be viewed. Location: Available for inspection by appointment. Sold ex-works. The printer and associated equipment are sold from their current location. The buyer is solely responsible for dismantling, removal, loading, transportation, shipping and installation at the destination. The buyer is also responsible for arranging any specialist lifting, transport or installation requirements. Buyers are strongly encouraged to inspect the equipment and assess access, lifting and transportation requirements before purchase. Additional Support removal wash tank also available separately (500L heated tank) please ask for further details.