Used Gripper for sale (780)

Condition: good (used), Year of construction: 2019, I sell the panel beam saw Macmazza Topsaw TS90. Year 2019. Cutting size 4300x4300mm. Cutting height 90mm. Fjdpfx Adezkmfle Iogd Main motor 7,5kW Scoring motor 2,2kW Total area covered W.5860mm x D.7610mm Gripper with pneumatic regulation Side alignment top roller with pneumatic stroke. Optimising software included. Very good condition. Available immediately.

Year of construction: 2026, condition: new, functionality: fully functional, Semi-automatic depaneling / basic machine with parallel shuttle The dynamic depaneling machine LOW 4322 XL is especially suited for medium to high product volumes and meets growing demands in the production process. Printed circuit board blanks of various materials are separated using low-dust and low-stress sawing and milling techniques with maximum product flexibility, precision and throughput. Highly dynamic linear motor axes, tools and grippers meet the highest quality requirements and guarantee the depaneling machine a long service life and high reliability. Semiautomatic depaneling - solutions on demand The LOW 4322 XL depanelling machine enables fast product changeover while maintaining short depanelling and handling times. The blank printed circuit board is inserted with a parallel shuttle, picked up and fixed with pin clamping technology and, if necessary, in combination with vacuum suction cups. Made in Germany The machine is equipped with: - a shank and slice tool separation module on Z-axis (automatically rotatable 0-90) - X-Y cross table module in linear motor technology with high-resolution measuring system - 2-compartment loading module built as parallel shuttle, separated left and right with sliding doors - Steel welding frame with two maintenance doors - left and right. ESD - standard vision system base module for teach-in programming - Working area is 520 x 480mm - Automatic cutter length processing - Remote maintenance/support via remote connection Fedpfx Adjvuw R Re Ijgd - Touch IPC with Windows 10 Pro operating system - Laser axis measurement incl. protocol - Air ionization - Cutter breakage control for end mills only - Preparation for vacuum clamping technology - ESD powder coating, RAL 9002, disc and sliding doors Optionally a vacuum cleaner unit can be offered later.

Condition: used, Year of construction: 2020, Overview This container sweep-off depalletiser (new glass) was manufactured in 2020 by Germany Krones AG. The machine is designed for high-speed depalletising of new glass containers in beverage production lines. It operates with a sweep-off system using a four-sided centring carriage to transfer complete container layers onto a discharge table. Technical data - Capacity: approx. 48,000 cont/h (up to 57,600 cont/h machine output) - Application: Depalletising of new glass containers - Configuration: Z-arrangement with pallet infeed and upper-level container discharge - Pallet handling: Pallet lifting unit with automatic empty pallet discharge Fedpfxsy Tn D Dj Ad Iegd - Discharge table: approx. 5,000 mm length - Conveyor: Steel chain conveyor - Drives: Servo drives (SEW) - Sweep-off system: Four-sided centring carriage, servo-driven - Layer handling: Integrated handling module with suction gripper system for layer pads and top frames - Vacuum system: Ejector-based - System Configuration: - Pallet lifting unit - Container discharge table (approx. 5,000 mm) - Steel chain conveyor system - Handling module with suction gripper - Packing material magazine - Empty pallet discharge system - Safety fencing (approx. 25 m) - Light barriers and safety circuits

Condition: used, Year of construction: 2012, Overview The Krones, Gera, Joha, Markl, Miho filling line for returnable glass bottles was previously used to fill beer in a brewery in southern Germany. Technical Specifications Fsdpfxjyb Sbue Ad Iogd - Output: 7,800 bph - Producs: Beer and CSD - Formats: - NRW 0.5 l - 0.33 l ring neck - 0.25 l LN Machine List  - Machine type: Decrater - Manufacturer: BMS - Year of manufacture: 2012 - Machine type: Decapper (Screw Cap) - Manufacturer: Rink - Decapping in the crate Euro 0,5l in 4x5 crate - Year of manufacture: 2012 - Machine type: Bottle washer - Manufacturer: Gera - Year of manufacture: 2024 - Machine type: Empty bottle inspector - Manufacturer: Krones - Model: Smarttronic - Incl. Pusher - Year of manufacture: 2012 - Machine type: Filler - Manufacturer: Kosme - Model: Isofill G 28/960 - 28 Valves - Year of manufacture: 2012 - With Combi Capper 4 heads(Crown Cork and Screw Cap) - Capacity: - 7,800 bph - Machine type: Labeling machine - Manufacturer: Krones - Model: Robusta - Refurbished in 2012 - 10 Bottle plates - 2 Label stations with 4 grippers and 4 glue pallets - Inkjet printer - Machine type: Crater - Manufacturer: BMS - Year of manufacture: 2012 - Crate format: Modul Crate 4x5

Condition: used, Year of construction: 2011, Overview This cold glue labeller was manufactured in 2014 by the German company HEUFT. It was used for the labelling and inspection of glass bottles including control of label presence, underfill detection by X-ray, and bottle breakage detection with automatic rejection. The machine includes special equipment for bottles with neck foil. It comes with 6 format parts. The Domino laser, vacuum unit and glue pumps are not included in the scope of delivery. It is available immediately and can be viewed by appointment. Fedpswz Evyjfx Ad Iogd Technical data  - Type: Cold glue labeller with 2 labelling stations (8 glue pallets, 6 gripper positions, machine pitch 120 mm) - Capacity: up to 36,000 bottles per hour (max. output without orientation, as per documentation) - Container type: glass, transparent - Container diameter: 59-67.5 mm - Container height: 226-260 mm - Closure material: metallic, closure diameter: 28 mm - Belt height: 1000 mm - Electrical connection: 400 V, 50 Hz - Max. Ambient temperature: 40 °C - Device diameter container carousel: 1150 mm - Control functions (Spectrum TX): Label control (sensors), underfill control (X-Ray), bottle breakage control, rejection - Special feature: Processing of NRW bottles with neck film Scope of Delivery  - HEUFT Tornado W incl. 2 cold glue stations - Spectrum TX control system - 6 format parts - Without domino laser, vacuum cleaner and glue pumps  

Condition: used, Year of construction: 2005, Overview  This cold glue labelling machine was manufactured in 2005 by German company HEUFT. The machine is no longer in production use and is now available for sale. It includes two integrated laser coders for date marking and supports a wide range of bottle formats. Ideal for high-speed beverage production environments. Technical data  - Capacity: Up to 60,000 bottles per hour - Formats: Supports 11 bottle formats - From 0,3l - 0,66l - Steini, NRW, Longneck - Container types: Glass, not transparent, non-contoured - Container diameter: 60.4 – 69.1 mm - Container height: 174 – 270 mm - Label positions: - Front (up to 2 labels) - Back (up to 1 label) - Label size range: - Width: 70 – 111 mm - Height: 33 – 100 mm - Band height: 1100 mm - Max. ambient temperature: 40°C - Power connection: 400 V - Machine design: Straight version, size L (approx. 3360 mm wide) - Bottle carousel diameter: 1610 mm - Number of bottle plates: 42 - Bottle rotation in carousel: Mechanical Fjdpfx Adswd Uk Se Iegd - Guide star diameter: 690 mm - Labelling stations: - 2 x Cold glue labelling stations - 8 glue pallets - 9 gripper positions - Automatic magazine feeding Scope of Delivery  - 1 x Labelling Machine | HEUFT | TORNADO | 2005 - Including: - 2 x Integrated Laser Coders | Bluhm - Complete labelling setup with format parts for 11 bottle formats - Cold glue stations, glue pallets, gripper arms, and automatic magazine - Technical documentation

Condition: used, Year of construction: 2017, Overview  Fgedpsvtpc Asfx Ad Iod This semi-automatic new glass pusher was built in 2017 by the German manufacturer Alwid. The machine is professionally stored and can be viewed in person at any time. Technical details - Semi-automatic new glass pusher with interchangeable gripper units - 4 heads: adjustable depending on the layer pattern - ALWID FEEDING TABLE + ALWID DEPALLETIZER

Condition: used, Year of construction: 2018, Overview  The offered filling line for pouch bags was designed by a Swiss company and also delivered by them in 2018. The main manufacturer is Linapack. The line was only used for seasonal production only (2 months a year), therefore the working hours are very low. As the sales volumes are not further increasing, the seller decided to sell the line and stop the production. The line is still assembled and can be shown. It is possible to handle different formats of pouch bags and to do hot filling up to 85°C. The current owner used it for Cocktails but it can also be used for various other non carbonated drinks. Tech. Details - Capacity: - 50 bags/ hour, depending on the volume - 750 -900 l/h - Bag dimensions - Width: 80 - 180mm - Height: 100 - 300mm - Filling temperature: 71 - 85 °C - Siemens PLC Line consists of  - 1,000 l buffer tank - agitator - Flow meter - Level detection - Cleaning spray ball Fgodsvptt Rjpfx Ad Iod - Integrated into pasteurizer control system - Flash pasteurizer Kreuzmayr PAS-900 - Capacity: 750 - 1,000 l/h - Heated with steam - Fully automatic - Automatic cleaning with - Hot water - steam - acid - caustic - With tubular heat exchanger - Automatic filler Linapack LFS-1000 Duplex - with Siemens PLC - Seven Station system - motorized magazine with pick and place system to supply pouches - Opening of the pouches with vacuum gripper - Filling unit with flow meter and temperature sensor, automated rejection, if temperature is too low - Sealing of pouches - Sealing of pouches - Cooling of the seal - Pouch discharge - Check weigher - Cooler and dryer for pouches - Cooling in water bath - With UV lamps for desinfication - Drying by blower, five nozzles - Conveyors and collection table

Condition: excellent (used), power: 200 kW (271.92 HP), chain condition: 70 %, Year of construction: 2015, operating hours: 7,507 h, Equipment: air conditioning, LIEBHERR R946 NLC Year: 2015 Operation hours: 7.507 hrs. ROPS Fsdpfx Adjzkg Sxe Iogd Cabin protection Airco Radio Back drive camera Monoboom Stick: 3,30 meter All hydr. Lines (hammer-, gripper-, scissor-) quick coupler SW66 Likufix 1x rock bucket with 1.4m width Central lubrication U/C: 70% good trackshoes: 600 mm engine with 200kW CE / EPA Operation weight: 40 tons

Condition: used, Year of construction: 2008, operating hours: 13,000 h, functionality: fully functional, The Bruderer BSTA 500-110B is a 500 kN Swiss-built high-speed stamping press, fitted with a BSV 75T double servo feeder for precision two-track strip feeding. Capable of up to 750 strokes per minute with B2 touch-screen control. Nominal force: 500 kN (50 tons) Year of manufacture: 2008 Stroke rate: 100–750 spm (variable) Adjustable stroke: 19 / 25 / 34 / 43 / 51 / 57 / 64 mm Ram height adjustment: 64 mm Press table area: 1080 x 650 mm Control: B2, IPC-based touch-screen press control, programmable memory for fast retooling BSV 75T DOUBLE SERVO FEEDER Type: tandem dual-feed servo unit, independently controlled tracks Max. strip width: 70 mm per track Max. material thickness: 2 mm Feed length: variable, freely programmable Fgedpfxozh Nnwj Ad Ijd Feed angle: variable Pilot release angle: variable No clamping/gripper bars — strip held by driven feed rollers during stamping Designed for parallel advancing of two strips or feeding pre-profiled/pre-stamped strip

Condition: excellent (used), Year of construction: 1999, cutting length 3.200 mm cutting width 3.200 mm cutting hight 65 mm saw blade DM max. 300 mm saw blade motor: 5,5 kW scoring unit DM max. 160 mm motor scoring unit 1,5 kW front support tables 3 Stk. 1 x 2500 x 500 & 2 x 1500 x 500 mm cutting optimisation program no. of grippers 8 pcs saw blade hight adjustment on THK guides pressure beam with openings side pusher (alignment) saw blade quick change system suction DM1 x 120 & 1 x 150 mm space requirement L x B 5700 x 6000 mm weight approx. 2500 kg Fgsdpfx Ashvan Iod Isd INVERTER NEW Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: good (used), Year of construction: 2014, functionality: fully functional, Sheet width: 3000 mm Sheet length: 1500 mm Sheet thickness: 8 mm Workpiece weight: 200 kg Punching force max.: 220 kN Total power requirement: 9.5 kW Space requirement approx.: 7395 x 6540 x 2072 mm Equipment: Punch head: - Hydraulic single-tool chuck with 360° rotation - Manually adjustable clamping force - Programmable clamp (active/passive/re-positioning) - Spray lubrication for punch - Stroke counter for punch - Level monitoring for threading and tool lubrication Control system: - Open control system based on Sinumerik 840 D - 12" TFT color display - Teleservice via internet - Automatic shutdown Data transfer: - USB interface - RJ-45 network connection Safety: - CE marking - Dual light curtains - Rapid shutdown of hydraulics - Bulge detection Programming: - TruTops Punch via network access 1 x MultiTool function 1 x MultiShear function 1 x Thread forming function Fgjdpfxey Sak Ts Ad Isd 1 x Deburring and rolling technology 1 x SoftPunch function 4 x individually openable clamping jaws 4 x height-adjustable clamping jaws 1 x Re-positioning cylinder 1 x Sensor for stripper (included in rest material-free processing) - GripMaster - Rest material grippers with sensor technology - Shear lift table 400 mm - Tilting rest material pallet 3000 x 1500 mm - SheetMaster - Operating hours: 65,000 h

Condition: used, Year of construction: 2001, Deckel Maho DMC 60U Hi-dyn Machining Center Condition: Used Fodpfx Asu Rnlued Ijgd Year of manufacture: 2001 Power-on hours: 56,376 Spindle hours: 26,451 Technical specifications: Travel X/Y/Z: 600 / 700 / 600 mm Motor power: 15 kW (40% duty cycle); 10 kW (100% duty cycle) Spindle speed: 18,000 rpm Tool holder: HSK 63 Magazine capacity HSK 63: 60 tools Equipment: - 3D trajectory control MillPlus IT - Horizontal double gripper tool changer - Automatic swivel milling head - Rotating safety viewing window - NC rotary table with pallet support - Pallet changer - 2 pallets, 630 x 500 mm - Universal milling head with controlled B-axis HSK 63 (only in combination with HSK 63 motor spindle) - Tool holder for HSK-A63 according to DIN 69893 - Electronic handwheel - Operating mode 4: Extended manual intervention - Rinsing gun with pump - Tool breakage monitoring HSK 63, mechanical version, range: 63...310 mm / +/- 3 mm - Intermittent operation chip conveyor - Internal coolant supply switchable from 40 bar to 80 bar

Condition: excellent (used), Year of construction: 2003, I sell the panel beam saw HOLZMA HPL11/43/22. Year 2003. Cutting size 4300x2200mm + back loading table. Cutting height 125mm. Total area covered W.7060mm x D.9490mm 7 pcs. gripper with pneumatic regulation Fgodpfx Aezkb T Dsd Ied Side alignment bottom pad with pneumatic stroke. CE conformity and optimising software included. Very good condition. Available immediately.

Year of construction: 2005, condition: good (used), machine/vehicle number: 815 1015 1794, Manufacturer: CFS Germany GmbH Type: JuniorPak M420 Year of manufacture: 2005 Voltage: 400 V Phases: 3-phase + N + PE Current: 29 A Power: 20 kW Frequency: 50 Hz Weight: 2200 kg This is a thermoforming machine (deep-draw machine) for the production of vacuum-packed or MAP-packed food. It is designed for medium-sized production lines and is often used for meat, cold cuts, cheese, fish, and ready meals. How the JuniorPak M420 works 1. Bottom film feeding A roll of plastic film is mounted at the rear of the machine. The film is drawn forward using conveyor chains with grippers. Common materials: APET/PE PA/PE PP PET barrier film 2. Heating The bottom film enters the heating zone. Here, the plastic is heated to approximately: 90–140 °C, depending on the material type. The temperature is controlled by electric heating plates. 3. Deep drawing This is the machine's most important process. The mold closes. Then, usually: vacuum is applied under the film compressed air is applied above the film, if required the film is drawn down into the mold The result is finished plastic containers or trays. The forming depth is determined by the mold. 4. Filling zone After forming, the process stops. Operators or automatic equipment place the product in the trays. Examples: meat burgers bacon cheese fish 5. Top film A new film is fed in from above. This lies over the product. Fgsdpszka Ruefx Ad Isd 6. Vacuum/MAP The sealing chamber closes. The machine can: create a vacuum flush with gas seal directly In MAP, the following are often used: CO₂ N₂ O₂ The gas mixture depends on the product. 7. Sealing The top film is sealed to the bottom film. Sealing occurs with: temperature pressure time These three parameters are crucial for a tight seal. 8. Cutting The cutting tool cuts each individual package. Excess film is transported out as scrap. 9. Ejection Finished packages are transported out onto a conveyor belt. They can then: be labeled be weighed be checked with a metal detector be packed in boxes A JuniorPak M420 normally consists of: Frame made of stainless steel Film transport with chains Heating station Forming station Filling zone Vacuum/MAP chamber Sealing tool Cutting tool Ejection conveyor Vacuum pump Pneumatic system Hydraulics (on some models) PLC control with HMI Typical technical data For the M420 series, typical values are: Maximum film width: approx. 420 mm Forming depth: up to approx. 100–120 mm, depending on the tool Cycle time: 5–15 cycles/min Capacity: from a few hundred to several thousand packages/hour, depending on the product and tool Connection: 400 V 3-phase Power: 20 kW (as shown on the nameplate)

Condition: used, Year of construction: 2001, functionality: fully functional, The Schaal SEP 80 is a 80-ton eccentric press designed for precision stamping and forming. Its Unidor electronic control system ensures repeatable stroke accuracy and fast setup, while the integrated tool safety device protects dies from damage caused by misfeeds or incorrect part positioning — reducing downtime and tooling costs. The machine features a rigid double-column O-frame in vibration-damping cast iron, 6-point play-free roller ram guidance, and a flywheel drive with pneumatic clutch/brake combination. It comes equipped with a gripper feeding device SZV 302 feed unit for automated strip feeding. Pressing force: 800 kN (80 tons) Strokes per minute: 60 – 320 min⁻¹ Ram stroke (adjustable): 8 – 80 mm Ram adjustment: 80 mm Ram surface: 700 × 500 mm Table size (clamping plate): 830 × 700 mm Clamping plate thickness: 80 mm Table opening: 500 × 200 mm Strip feed clearance: 120 ± 40 mm Feed unit: Schaal SZV 3 Strip width: 10 - 270 mm Thickness: 0 – 4 mm Drive power: 21.5 kW Weight: 8,000 kg Footprint: 1,500 × 2,000 mm, height: 2,885 mm Fgedpfx Adjzhw Huo Iod

Year of construction: 2017, condition: used, Case maker Kolbus DA 270 Bookjet Edition Year: 2017 Equipped with: Fsdszhwu Ejpfx Ad Ijgd - Copilot system with touchscreen - Board magazine for manual loading - Cloth feeder for non-stop operation with pile magazine, max. stacking height 160 mm - Miss cloth control during the separation process - Counter stacker delivery with following roller conveyor - Moveable gluing station for processing hot-glue with glue preparation unit in the premelter, heated glue application roller and scraper roller - Cloth cylinder with grippers and exchangeable plates for rubber pad (incl. 5 x 500 mm, 5 x 720 mm and 10 x rubber pad) - Viscosity control device for automatic water supply to ensure constant glue viscosity with pump and water tank for manual filling - Device for inside lining with hot-glue - Pressing roller device for crease-free connection of the cover material with boards and spine strip - Device for producing padded cases - Automatic case counter - Programmable automatic settings, motorized adjustments, indication of production faults - Single case request for control purposes done from the operating side - Servo-controlled drive technology based on Siemens SIMOTION D Special equipment: - without centre strip roll device (optional available new!) - With board centre strip magazine, boards height min. 130 mm - Board centre strip cutting device (cross centre strip) for processing digital print products of varying centre-strip, device for cutting rigid centre board strips to width, with possible width variatio from cycle to cycle - Kolbus Turning Device WE 260, year 2017 (counter: only approx. 4,7 mio. book cases) Technical specifications: - Mechanical speed: up to 65 cycles/min - Open cover size max.: 670 x 390 mm - Open cover size min.: 205 x 140 mm - Joint width: 4 - 15 mm - Spine width: 14 - 120 mm - Turn in width closed: 8 - 15 mm - Cloth width: 223 - 708 mm - Cloth height: 130 - 428 mm - Board thickness: 1 - 4 mm - Board width: 95 - 328 mm - Board height: 140 - 390 mm - Board centre strip thickness: 1 - 4 mm - Board centre strip width: 6 - 90 mm

Condition: used, Year of construction: 2014, Approx. 97 million prints Format: 94 x 64 cm (37 x 25 inches) installed in 2015 Fjdpfsxb U Ayex Ad Iegd short-term available Technical data: PQC-S control console with touchscreen KOMORI KHS-AI system for makeready time optimization KOMORI Smart Feedback for density adjustment and waste reduction Automatic washing and ink presetting KOMORI PSP automatic format and thickness adjustment AMR (Automatic Make Ready) for preset job changes Quick start function for production Remote control of register and transfer cylinder adjustment Automatic sheet format adjustment Pneumatic stop fingers Mechanical and ultrasonic double sheet detection in the feeder S-APC: semi-automatic plate change (no plate bending required) KOMORI DSC high-performance sheet guide with exclusively double-size countercylinder and transfer cylinders KOMORImatic film dampening unit technotrans alpha.c dampening system Antistatic blower at the feeder head Side blower (feeder) 2-zone suction belt delivery table Delivery with sheet troller/smoother Sheet brake with infinitely variable speed adjustment Blowing bars above the delivery pile Antistatic bar above the delivery pile Adjustable fans for precise paper travel and pile formation Weko AP160 printing powder device KOMORI PDC LII, online density measurement KOMORI PCC CIP3/4 data conversion software Max. sheet format: 640 × 940 mm Min. sheet format: 297 × 420 mm Max. print format: 620 × 930 mm Plate format: 700 × 945 mm (thickness: 0.30 mm) Blanket size: 800 × 955 mm (with bars) Substrate thickness: 0.04–0.6 mm Gripper margin: 10 mm Plate clamping margin: 45 mm Max. printing speed: 13,000 sheets/hour Stack height feed: 800 mm Stack height at delivery: 900 mm (*depending on paper, ink, and operating conditions) Length: approx. 8,169 mm Width: approx. 3,320 mm (without peripheral devices) Power consumption: approx. 53 kW / 50 Hz (without peripheral devices)

Condition: used, Year of construction: 2011, machine/vehicle number: M337, Used RAVECCO MORAVEC filling triblock 12-12-1C for waterTechnical Specifications & Performance DataThis second hand Filling Monoblock by Raveco Moravec combines rinsing, filling, and capping in a compact rotary platform designed for efficient beverage production and industrial packaging. Engineered for glass bottles, it is a reliable choice for a used bottling line seeking flexible closure options and straightforward integration.Manufacturer: Raveco MoravecModel: 12-12-1C MonoblockSpeed: 2.500 BPH ( Bottle per hour)Configuration: 12 rinsing grippers, 12 filling valves, 1 capping headContainer types: Glass bottlesBottle formats: Compatible with 0.33L, 0.5L, 0.75L, 1.0L bottle formatsNeck finish: Long neckClosures: crown capsConstruction year range: 2009–2011Machine type: Rinser–Filler–Capper monoblockAdvanced Automation & Control SystemsThe machine utilizes a Moravec control platform with manual operation, providing straightforward and dependable control for operators. Core functions for rinsing, filling, and capping are synchronized within the monoblock to maintain consistent bottle handling and process timing. Operator access is designed for quick intervention and basic parameter adjustments, supporting reliable changeovers between closure types.Moravec control system with manual operationSynchronized monoblock timing for rinse–fill–cap sequenceOperator-friendly controls for format adjustmentsStandard emergency stop and interlocked guarding typical of industrial packaging machineryProduction Line Integration CapabilitiesThis Filling Monoblock is configured for a straight-line conveyor layout, enabling smooth integration within a used bottling line or operation as a standalone module. It accepts a range of glass bottle formats and supports quick format and closure changeovers, making it suitable for flexible beverage production environments.Inline integration on straight conveyor layoutsStandalone or in-line operation within broader bottling equipmentFormat flexibility from 0.33L to 1.0L glass bottlesChangeover capability crown closuresMachine Condition & Maintenance HistoryThe equipment is currently in occasional operation and has been in service approximately 25 hours per week during recent use, with remaining time on standby. It has been serviced regularly over the past year of ownership. Testing is available, including both dry run and production tests, to verify operational performance before integration into a second hand production line.Operational status: Occasional operationTesting availability: Dry run and production test possibleService status: Regularly serviced during recent useDocumentation: Technical manuals and schematics not on handSpare parts: Not includedOperational Performance & VersatilityDesigned for glass bottles with a long-neck fi... Fjdpfoy Uvhmox Ad Iogd

Condition: new, color: red, driver cabin: other, gearing type: other, Equipment: crane, Vehicle location: Bovenden, emergency stop, gripper control, foldable, 2-point mechanical support, radio remote control, 3x hydraulic extensions. Superstructure: ARCHIVE IMAGE, HMF 340-K3 RC, radio remote control, 20 available! Compact knuckle boom crane with high lifting capacity, radio remote control, 3 hydraulic extensions, hydraulic reach 7.15 m, lifting capacity 985 kg at 3.2 m outreach, up to 435 kg at 7.15 m outreach. Fsdpfxozi E Ipe Ad Isgd Load chart: 3.2 m - 985 kg, 4.5 m - 695 kg, 5.8 m - 535 kg, 7.1 m - 435 kg! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors!

Condition: repair required (used), Year of construction: 2022, functionality: limited functionality, Used Spinner Robobox, used to automate the loading and unloading of Spinner lathes with plastic components. Fanuc M10iD 6-axis robot, 1420 mm reach, 12 kg gripper unit. Barely used. Dual gripper, 5 drawers 800 x 600 mm (3 x 150 mm, 2 x 200 mm height). Safety scanner. Note: Display and hard drive need to be replaced. Fgodpjzi Elhofx Ad Ied

Condition: like new (used), Year of construction: 2018, operating hours: 7,500 h, We are selling our Multilift V 15KG with only 7,500 operating hours. The machine can be inspected/tested; original purchase price was €59,000! Technical Specifications: Z-axis (crosswise to the machine longitudinal axis) Stroke: 1,600 mm Max. speed: 3.0 m/s X-axis (parallel to the machine longitudinal axis) Stroke: 900 mm Max. speed: 2.0 m/s Y-axis (vertical/plunge axis) Stroke: 1,000 mm C-axis (for gripper rotation) Fsdszi A Utjpfx Ad Iegd - Swing range 0° / 90°, both end positions monitored and manually adjustable - Pneumatic drive, including valve control - Max. torque at 6 bar: 28 Nm - Weight: 2.6 kg First vacuum unit (Venturi principle) with air saving function, suction capacity 65 l/min, blow-off function, vacuum switch for part monitoring, vacuum programmable, integrated condition monitoring for early detection of leaks and wear, routed close to the gripper; Customer-side hose connection: push-in fitting for hose size OD 6 / ID 4 Second vacuum unit (Venturi principle) with air saving function, suction capacity 65 l/min, blow-off function, vacuum switch for part monitoring, vacuum programmable, integrated condition monitoring for early detection of leaks and wear, routed close to the gripper; Customer-side hose connection: push-in fitting for hose size OD 6 / ID 4 Third vacuum unit (Venturi principle) with air saving function, suction capacity 65 l/min, blow-off function, vacuum switch for part monitoring, vacuum programmable, integrated condition monitoring for early detection of leaks and wear, routed close to the gripper Fourth vacuum unit (Venturi principle) with air saving function, suction capacity 65 l/min, blow-off function, vacuum switch for part monitoring, vacuum programmable, integrated condition monitoring for early detection of leaks and wear, routed close to the gripper; Customer-side hose connection: push-in fitting for hose size OD 6 / ID 4 Tenth pneumatic valve 5/3 with locked center position for gripper functions, piped to the gripper flange with quick-release couplings DN 2.7 for hose size OD 6 / ID 4; customer-side hose connection 8 freely programmable inputs for querying 8 gripper-mounted sensors, pre-wired to the gripper flange with a 25-pin connector; up to 8 sensors can be monitored; the corresponding mating connector for the gripper-side connection is included Second interface for querying 8 additional sensors, via 25-pin connector on the gripper flange, incl. mating connector for gripper-side connection Third interface for querying 8 additional sensors, via 25-pin connector on the gripper flange, incl. mating connector for gripper-side connection Fourth interface for querying 8 additional sensors, via 25-pin connector on the gripper flange, incl. mating connector for gripper-side connection Interface with 4 freely programmable inputs and outputs, non-isolated, on a 42-pin socket on the MULTILIFT, for peripheral devices Additional interface with 16 freely programmable inputs and outputs (24V DC), non-isolated, wired to a 72-pin socket on the MULTILIFT Push-in fitting for hose size OD 6 / ID 4

Condition: ready for operation (used), Year of construction: 2013, functionality: fully functional, machine/vehicle number: Serial No. 130594, load capacity: 100 kg, controller manufacturer: Yaskawa, controller model: DX100, teach pendant manufacturer: Motoman, Equipment: documentation/manual, Complete Yaskawa ES165D-100 robotic palletizing cell with DX100 controller For sale is a complete, fully functional palletizing cell, which is currently still in use in our production and can be inspected under load by appointment. The system is used for the automatic palletizing of cartons (packages) containing snack products and is fed by two infeed lines. Scope of delivery: Yaskawa Motoman ES165D-100 (100 kg payload) Yaskawa DX100 controller complete control cabinet gripper system protective enclosure / safety fences two vertical conveyors two discharge conveyors complete palletizing cell Technical data Year of manufacture: 2013 Fodpfjzi Ay Aox Ad Isgd Robot: Yaskawa Motoman ES165D-100 Controller: DX100 Payload: 100 kg System currently in production regular maintenance performed and documented Optional An end-of-line packaging machine from Meurer can also be offered. Dismantling and transport are to be organized by the buyer. An inspection of the operating system is possible by arrangement.

Condition: used, Pipe gripper, round gripper, laying tongs, round material gripper, scissor gripper, pipe laying device -Manufacturer: Siegert, round material gripper round pliers type RZ -Gripping range: 50 to 250 mm -Load capacity: 250kg Fsdpfx Adorkp Nqj Iogd -Dimension: 630/250/H450 mm -Town weight: 11 kg

Year of construction: 2016, condition: good (used), Sheet metal clamp, sheet metal claw, beam clamp, beam claw, sheet metal gripper, material gripper, material gripper -Sheet metal claws -Span: 0 to 30 mm -Load capacity: 3000 kg Fgodpfsd Aqtrsx Ad Ijd -Number: 2x terminals available -Price: per piece -Weight: 15.4 kg/piece