Used Beveler for sale (501)

Condition: used, Year of construction: 2007, table diameter 4520 mm table load 35000 kg swivelling range 110 Grad Lasdpfsrmulvsx Ab Ujh total power requirement 44 kW weight of the machine ca. / t required space / m Type: ROMAT 350 / LVEB-120000N-4m / VVEs-D-18000N-5m-S / QVEB-2m travelling beam / CR-200000N / Hydraulic scissor lift table In the scope of delivery: Item Designation 1 Welding power source GLC 603 Quinto SD 2 Wire drum 3 Service door 2.1 4 Robot control cabinet 5 Service door 1.2 6 Scissor lift table (shown in parking position) 7 Cross-travelling unit QVEB 8 ROMAT 350 robot 9 Service door 1.1 10 Safety fence 11 Platform 12 Positioner 13 Sliding door 1 14 Linear traversing unit LVEB 15 Vertical traversing unit VVEs 16 Sliding door 2 The disc ring on the table is a device that is not included in the scope of delivery ----- Technical data - Mechanical dimensions (without control unit and superstructures): approx.6440(57 7 0)x4520(2700)x5460(3320) LxWxH - Turntable diameter: 4520mm - Weight: approx. 25,000kg (without superstructure) - Speed range: 0.004 - 1.07 rpm - Welding current coupling: 600 A - Maximum table load capacity: 35 tons (according to load chart) Ambient temperature Storage / transport 0 to 60'C Operation +4 to 35 "C Interfaces Central transfer point for control, power supply, earth connection ----- 2.3 Linear traversing unit, LVEB Type LVEB-120000N 4m Dimensions W x D x H 7,700 x 2,440 x 776 mm Weight 4,355 kg Travelling distance 4,000 mm Load of the carriage 120,000 N Drive unit Gear motor Precision bevel gear motor Manufacturer Stöber Type K402VF0250EK703V Power 4.21 kW Voltage UKE 140 V / 1000 rpm Current Rated current IN: 8.32 A Type of current Standstill current I0: 9.04 A Motor speed 3,000 rpm Gear ratio i = 25.28 ----- 2.4 Vertical traversing unit, VVEs Type VVEs-5m Dimensions W x D x H 2,000 x 1,960 x 7,150 mm Weight 9,500 kg Travelling distance 5,000 mm Max. moving mass 18,000 N Drive unit Gear motor Bevel gear motor with brake Manufacturer Stöber Type K713VF0790MQ30ED704B Power 4.8 kW Motor speed 2,000 rpm Gear ratio i = 78.83 (20181/256) ----- 2.5 Cross-travelling unit, QVEB Type QVEB-2m Dimensions W x D x H 1,270 x 4,100 x 756 mm Weight 1,950 kg Travelling distance 2,000 mm Load on the travelling beam 10,000 N Max. moving mass 18,000 N Drive unit Gear motor Precision flat geared motor Manufacturer Stöber Type FS202VQ0145ED402U Power 1.43 kW Voltage UKE 140 V / 1000 rpm Rated current IN 2.86 A Type of current Standstill current I0: 3.1 A Motor speed 3,000 rpm Gear ratio i = 14.65 (3180/217) ----- 2.6 Rotary indexing table Type CR-200kN Manufacturer Cloos Dimensions W x D x H 1,820 x 2,120 x 541 mm Weight 2,850 kg Drive unit Gear motor Bevel gear motor Manufacturer Stöber Type K814VG1540EK803U Power 6.7 kW Motor speed 3,000 rpm Gear ratio i = 154.322 ----- 2.7 Robot ROMAT 350 Type ROMAT 350 Dimensions (W x D x H) in reference position 1,900 x 600 x 1,500 mm Weight 205 kg Footprint 500 x 515 mm N...

Condition: used, Edge beveling machine, edge milling machine ACKERMANN & SCHMITT Type ZL 1104 Edge breaking machine, deburring machine, edge deburring device For aluminum and plastic processing and small chamfers on steel. Year of manufacture: approx. 1995 Chamfer size: 0-4 mm Chamfer angle: 45° Cutter head: Ø approx. 40 mm Material support: 90° x 400 mm Speed: 4500 rpm Motor power: 700 watts Power supply: 220 volts, 50 Hz - Infinitely adjustable chamfer size, 0-4 mm - Built-in milling cutter with carbide indexable inserts - Milling motor with 8 mm collet chuck - Workpiece support 90° Lsdpfx Asxcbmueb Ujah - Workpiece support mount defective, needs repair - Motor runs well Net weight: 3 kg

Condition: new, functionality: fully functional, overall weight: 1,000 kg, empty load weight: 320 kg, maximum load weight: 680 kg, axle configuration: 1 axle, loading space length: 2,460 mm, loading space width: 1,270 mm, loading space height: 100 mm, suspension: other, Year of construction: 2025, machine/vehicle number: 13282707, Product information "Vezeko Lowering Trailer 127x246cm 1.0t | Side Wall Extension" Load dimensions: approx. 1270 mm x 2460 mm External dimensions: approx. 1950 mm x 4080 mm Permissible total weight: 1000 kg Payload: approx. 680 kg (payload varies depending on additional equipment) Manufacturer: Vezeko Features Laedji R Hxnjpfx Ab Uoh - Lowering trailer - Anodized aluminum side walls 100 mm - Removable aluminum side wall extension 250 mm - Hydraulically lowerable loading platform (manual pump) - Shock absorbers installed, incl. registration for 100 km/h - Rear end beveled - 4 lashing rings on outer frame - 8 lashing points in the loading floor - Lockable front storage box - Vehicle documents included Additional equipment - Floor panel: wooden floor - Wedge & holder Chassis - Rubber suspension axle | V-drawbar with ball coupling | Jockey wheel Electrics - 12 volt | 13-pin plug | side marker lights | position lights If you wish to purchase this trailer or have further questions about trailers, please use our internal lowering trailer "No. 13282707".

Condition: used, Year of construction: 1997, machine/vehicle number: 4406, 3D UV dryer Superfici Elmag 2 tubes - 3D UV-dryer Superfici & conveyer - the pictures show the machine before overhaul - Producer Superfici - Type TU166-30 + 2 UVM55 - Year of construction 1997 - Working width 1300 mm - Number of lamp from top 2 Stk. - Lamp bevel to conveyor - For mercury lamps - For gallium lamps Lsdpfxotz Dg Ue Ab Uoah - Electic capacity lamp 80 W/cm - Selective shiftable 80/40 W/cm - Feed speed infinitely adjustable by hand wheel ~ 2 - 7,5 m/min - Location - Voltage / HZ 400 / 50 - Commodity code 8419 3200

Condition: good (used), Gearboxes, spur gears, bevel gears, transmission gears, crane gears, hoist gears, grab lifting and closing gears -Manufacturer: GfA, Elektromat Type SE 3.5.120-25.00 -Speed: 120/20 rpm see photos nameplate -Motor: Siemens, power 0.37 kW -Shaft: Ø 25 x 100 mm Lodpfx Abexb Rppo Ueah -Protection class: IP 55 -Dimensions: 375/140/H260 mm -Weight: 11.6 kg

Condition: used, Used machine Equipment and technical specifications: Automatic edge feeder Cartridge glue system 4-roll printing unit Cross-cut saw unit Flush trimming unit Combination trimming unit: flush/bevel/radius Radius scraper Buffing unit Edge band thickness 0.3 - 20 mm (depending on unit) Edge band height max. 66 mm Edge band length min. 200 mm Feed rate 8/16 or 12/24 m/min With LIGMATECH workpiece return system Ledpfxsw Nad Hj Ab Uoah The return line of this return system is located above the panel processing level. The workpieces move back to the operator on an inclined plane. Special features compared to the ZHR 0x models: Automatic detection and rotation of parts from transverse to longitudinal Automatic adjustment of the rotation speed to the workpiece length Minimum and maximum workpiece dimensions For longitudinal edge processing: 2200 x 1000 For transverse processing with subsequent rotation: 250 x 120/2200 x 800 Maximum workpiece thickness: 60 mm Location: Bavaria Availability: Short-term

Year of construction: 1992, condition: excellent (used), machine/vehicle number: 24, Kom.No.: 551.3852 Colours: 6 Equipment / Additional information: Consists of: • Stacker • Printing machine • Cup feeding Laodpfxen D E A Ts Ab Ush • Stapler Technical data Printing unit type DW 200-230 Plate cylinder diameter 200 mm Max. possible print image width 110 mm Number of print segments 4 pieces Max. cup rim diameter 130 mm Min. cup rim diameter 70 mm (55 mm) Max. print image unwinding (specific plate unwinding) (361 mm) / D 115 Max. cup height 130 mm Min. cup height 35 mm Max. bevel 10 degrees Production speed depending on cup size, quality and raw materials with UV drying up to 24,000 C/h El. connection value (machine, drying and stacking) approx. 35 KVA El. control with Siemens PLC / control station with 2-line display

Condition: good (used), Year of construction: 1996, Offer 25115 Technical Data: - Saw blade diameter: 400 mm - Saw blade speed: 3000 rpm - Cutting height up to approx.: 125 mm - Cutting depth up to approx.: 600 mm Ledewn D Emspfx Ab Uoah - Bevel adjustable on 2 axes - Table size approx.: W 800 x D 800 mm - Table height: 920 mm - Drive: 400 V / 1.5 kW - Space requirement approx.: W 800 x H 1900 x D 1100 mm - Weight approx.: 200 kg

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 6119, We sell a used CEVISA beveling machine CHP-60G, MFG 2024, SN: 6119 60 mm bevel length; capability in one run: 28 mm bevel length; bevel finish: machined (milling head); adjustable bevel speed depending on the material; optimum beveling speed: 500 mm/min; continual plate fixing pressure system: 4 Bar; 3 feeding rollers always in contact with the plate; 1 roller positioned in the cut-off point to insure: - no vibration; no noise; -smooth and unchanging finish; portable milling machine; mobile and stable; adjustable working height with pneumatic lifting system; electronic bevel adjustment; display: high precision; built-in adjustable bevel angles from 15º to 70º Laodsv Ed N Ijpfx Ab Uoh * Nominal thickness: from 10 mm to 100 mm. Motor: three-phase; motor power: 5 CV – 3.8 kW; voltage: 220/380 V. 50 Hz; 250/440 V. 60 Hz; 32 A plug, cable diameter: 2.5 millimetres, maximum consumption of the machine: max. 15A. Electric box with: thermomagnetic switch trip +emergency stop button net weight: 800 kg; works height: adjustable from 760 to 940 mm; built-in trolley; bevel blueprint; plate beveling: K, V, X and Y bevels, bevel speed: 0,5 m/min, three-phase motor: three phases and earth. no neutral, motor power: 5 hp - 3.8 kW, air flow rate 200 l/min. Electrical box: with under voltage trip, emergency stop button, magneto-thermal protection; net weight of the beveling machine: 800kg, working height: adjustable from 760 to 940 millimeters. Integrated carriage. Price: 39280 Euro + VAT, negotiable , FCA Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: used, mileage: 104,000 km, power: 375 kW (509.86 HP), first registration: 06/2024, fuel type: diesel, axle configuration: 2 axles, color: white, gearing type: automatic, emission class: euro6, overall weight: 18,000 kg, Equipment: ABS, air conditioning, electronic stability program (ESP), navigation system, parking heater, soot filter, Demonstration vehicles 3 units available Main components FH Globetrotter safety driver's cab Wheelbase: 3,800 mm Chassis height: MED (medium) Diesel engine 12.8 l, 510 hp/375 kW, 2,550 Nm Rear axle RSS1352A, single gear, 13 t axle load, GZG 52 t I-Shift AT2612, automated 12-speed gearbox (direct gear), max. input torque: 2,652 Nm Drive axle ratio 2.47:1 Reinforced engine brake Volvo Engine Brake+ (VEB+) Aluminum rims Dura-Bright EVO (polished) Paint: 1103WHIT winter white FH rest package, one bed Info and media package with Navigation Driver comfort package Side collision avoidance and turning assistant (both sides) Close-up camera on passenger side I-ParkCool (integrated auxiliary air conditioning with automatic temperature control) PTO PTR-DH (fast), gearbox side, connection: 1 DIN rear for pump Interior of driver's cab, living area Comfort driver's seat, air-suspended, heated, seat belt Two armrests on driver's seat Armrests covered in leather Standard passenger seat, fixed Foam comfort mattress for lower bed, hard, foldable, with safety net Basic mattress topper (20 mm) Storage space under bed Storage compartments above bed, capacity: 245 l Switch console (basic) on bed (interior light, auxiliary heating, roof hatch and door lock) Cool box 33 l, with freezer compartment, under bed Compartment under dashboard with drawer Bottle holder at front and rear Make-up/shaving mirror Two flexible reading lamps Interior lighting with dimmer and red night lighting Side sun visor, driver's side Interior sun visor, manual roller blind Roof window and emergency exit, can be opened manually (tinted glass) Curtains on windscreen and windows 2 rubber floor mats Central locking with remote control Auxiliary heating in driver's cab, 2 kW Automatic climate control with sun sensor Interior of driver's cab, driving Load/axle load display in vehicle display Battery display in display Steering wheel, leather version Steering wheel adjustment in height and inclination, with additional steering shaft adjustment Roof antenna and preparation for CB radio Digital tachograph, generation 4 Eco-Cruise-Control (cruise control) including braking cruise control Lane keeping assistant Battery pulse device Ledpfx Ajtxfw Reb Usah Adaptive cruise control (ACC) with collision warning and emergency braking function Immobilizer, transponder in Key Gearbox/I-Shift operation via control unit on the driver's seat I-See with map-based topography information (high resolution) Stationary trailer brake active up to max. 7 km/h Electronic stability program (ESP), base with normal load center of gravity Chassis Rear axle load (technical) max. 13 t Front axle load (technical) max. 7.5 t Parabolic suspension at the front, 2-leaf (normal hardness) Air suspension at the rear, 4 air bellows Three driving heights for air suspension 650 liter aluminum tank on the left 112 liter AdBlue tank on the right Single battery system: one battery block (2 single batteries) for the entire vehicle electrics Two work lights at the rear/top of the driver's cab, white LED Trailer detection with LED sensor Frame end beveled Frame thickness 6.5 mm Frame profile height 266 mm Frame length at the rear 825 mm Extra Spring brakes on front axle Disc brakes, solid discs on steering axle Brake discs on drive axle, solid, 410 mm diameter Air compressor 2-cyl., 1,100 l/min Holding bracket (steel) for trailer connections behind cab Fifth wheel coupling SAF-Holland/GF, SK-S 36.20, cast 1 wheel chock, foldable, position at the front

Condition: good (used), Gearboxes, spur gears, bevel gears, transmission gears, crane gears, hoist gears, grab lifting and closing gears -Manufacturer: Mannesmann Demag, Gearbox Crane Gearbox -Type: AF08-MTranslation ratio: 36.9:1 -Motor: without electric motor (can be supplied at an additional cost) -Input- shaft: Ø 24 x 25 mm -Output hollow shaft: Ø 41/45 x 155 mm -Dimensions: 210/200/H360 mm Lodpjxb Rkmefx Ab Ueah -Weight: 33.5 kg

Condition: used, Year of construction: 1973, machine/vehicle number: 24109, Equipped with: Stock Divider Hydraulic Work Clamping Chip Conveyor Cutter Clamping Bolt Index Plate Change Gears Hydraulic System Coolant System Specifications: Min. Outside Cone Distance: 2.75" Max. Cone Distance: 10" Max. Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 6.8 to 16.5 RPM Feeds (seconds/tooth): 3 to 9 Lasdpsxdfa Usfx Ab Uoh Main Motor: 5hp, 900 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approx. Floor Space: 118" x 86.5" Needed Overall Height: 70" Approx. Net Weight: 16,000 lbs Shipping Weight Boxed for Export: 17,000 lbs

Condition: good (used), Year of construction: 1985, machine/vehicle number: 2.309.044, Offer 23195 Precision - deburring - faceting milling machine / edge milling machine Technical data: Steel - stainless steel - aluminum - plastic ,machining deburring and faceting process is done with milling cutter Ledpfonvdtcjx Ab Ujah Bevel angle 45 ° bevel width infinitely variable length of guide bar 500 mm working height 750 mm speed 2750 rpm drive 400 V / 0,7 kW space requirement approx. W 500 x D 400 x H 8500 mm Weight approx. 30 kg

Condition: excellent (used), Year of construction: 2024, functionality: fully functional, machine/vehicle number: 6125, We sell a used CEVISA beveling machine CHP-60G INV, MFG 2024, SN: 6125 60 mm bevel length; capability in one run: 28 mm bevel length; bevel finish: machined (milling head); adjustable bevel speed depending on the material; optimum beveling speed: 500 mm/min; continual plate fixing pressure system: 4 Bar; 3 feeding rollers always in contact with the plate; 1 roller positioned in the cut-off point to insure: - no vibration; no noise; -smooth and unchanging finish; portable milling machine; mobile and stable; adjustable working height with pneumatic lifting system; electronic bevel adjustment; display: high precision; built-in adjustable bevel angles from 15º to 70º * Nominal thickness: from 10 mm to 100 mm. Motor: three-phase; motor power: 5 CV – 3.8 kW; voltage: 220/380 V. 50 Hz; 250/440 V. 60 Hz; 32 A plug, cable diameter: 2.5 millimeters, maximum consumption of the machine: max. 15A. Electric box with: thermomagnetic switch trip +emergency stop button net weight: 800 kg; works height: adjustable from 760 to 940 mm; built-in trolley; bevel blueprint; plate beveling: K, V, X and Y bevels, bevel speed: 0,5 m/min, three-phase motor: three phases and earth. no neutral, motor power: 5 hp - 3.8 kW, air flow rate 200 l/min. Lasdpjv Ef Ryjfx Ab Ujh Electrical box: with under voltage trip, emergency stop button, magneto-thermal protection; net weight of the beveling machine: 800kg, working height: adjustable from 760 to 940 millimeters. Integrated carriage. Price: 42.840 Euro + VAT, negotiable , FCA Oradea/Romania Irrtum, Anderungen und Zwischenverkauf vorbehalten / Subject to errors, changes and prior sale / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. We speak English. /Wir sprechen Deutsch./ Beszélünk magyarul. /Nous parlons français/Vorbim romana

Condition: good (used), Gearboxes, spur gears, angle gears, worm gears, bevel gears -Manufacturer: Poggi, gearboxes, bevel gears Laedpfsxbdktjx Ab Ush -Translation: 1:2 -Shafts: Ø 24 x 50 mm -Number: 1x gearbox available -Price: per piece -Dimensions: 252/245/H85 mm -Weight: 4.7 kg

Condition: used, Year of construction: 1977, machine/vehicle number: 19909, Equipped with: Index Plate Geneva Cam Cutter Body Hydraulic Work Clamping Coolant Pump & Tank Chip Conveyor Additional Cutter Bodies, Index Plates & Geneva Cams Available Specifications: Minimum Outside Cone Distance: 2.75" Maximum Cone Distance: 10" Maximum Gear Pitch Dia.: 20" Cutter Diameters Utilized: 9 - 18" Root Angle: 55 - 80 Deg. Face Width: 3" Number of Teeth: 20 -75 Diameter of Taper Hole at Large End: 3-27/64" Taper Per Foot: .50" Depth of Taper: .625" Cutter Speeds: 15.6 to 87.7 RPM Feeds (seconds/tooth): 5 to 34.3 Main Motor: 10hp, 1800 rpm Hydraulic Motor: 7.5hp, 1800 rpm Approximate Floor Space: 118" x 86.5" Needed Overall Height: 70" Lasdjxdfazopfx Ab Ush Approximate Net Weight: 18,820 lbs Shipping Weight Boxed for Export: 20,500 lbs

Condition: good (used), Year of construction: 1992, machine/vehicle number: 454106, Technical data: min. / max. material thickness 3 - 25.0 mm max. helix length steel 400N/mm² 10 mm Ljdofg Uvdspfx Ab Ujah max. helix length steel 600N/mm² 8 mm max. helix length steel 800N/mm² 5 mm Working speed approx. 2.5 m/min Stroke rate 400 1/min Drive 400 V / 2000 Watt Space requirement approx. W 550 x D 200 x H 300 mm Weight approx. 13 kg

Condition: good (used), Gearboxes, spur gears, angle gears, worm gears, bevel gears -Manufacturer: Marzorati, gearbox type A 150 with magnetic filter Lsdpfx Aoxaz Rzob Usah -Shafts: Ø 32 x 45 mm -Dimensions: 310/275/H200 mm -Weight: 19.6 kg

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Ledpfx Absrtrzde Uoah Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Year of construction: 2010, condition: good (used), Offer 23026 Technical data: Laodpfx Aoi D D Ugob Ujh - Barrel width 1 - 15 mm - Cutter head with indexable inserts - barrel angle 30° - 37,5 - 45° - 60 ° - drive 220 V / 1100 Watt - space requirement approx. W 450 x D 300 x H 350 mm - weight approx. 20 kg - transport case

Condition: good (used), Gearboxes, spur gears, angle gears, worm gears, bevel gears -Manufacturer: Poggi, gearboxes, bevel gears -Shafts: Ø 24 x 50 mm -Number: 3x gearbox available -Price: per piece Ljdpfxjxazpqo Ab Uoah -Dimensions: 250/250/H86 mm -Weight: 4.9 kg/piece

Year of construction: 1995, condition: good (used), machine/vehicle number: 4202, Technical data: -Plate thickness up to 6-40 mm -Pipe Beveling min. Ø 100 mm -Max bevel in one run 10 mm - speed 2.6 m / min -Drive 400 V / 2,2 kW -Space requirement approx. B T 550 x 500 x H 700 mm -Weight approx. 65 kg Lasdpfjd Af Shsx Ab Uoh

Condition: good (used), Year of construction: 2012, machine/vehicle number: 00512S42, Offer 24379 Precision deburring and beveling machine / edge trimming machine Technical data: Steel - Stainless steel - Aluminum - Plastics ,- Processing Deburring and faceting process is carried out with milling cutter Ledpjud Ngqefx Ab Ujah Facing cutterhead with indexable inserts Motorized feed module Bevel angle adjustment 45 ° Continuously adjustable bevel width 0 to 10 mm Speed 2800 rpm Drive 400 V / 1.5 kW Space requirement approx. W 600 x D 750 x H 950 mm Weight approx. 90 kg

Year of construction: 1990, condition: good (used), machine/vehicle number: XXXX, Lg.No. 20314 Technical data: steel - stainless steel - aluminum - plastic ,machining deburring and beveling operation is carried out with milling cutter support angle - bevel angle inclinable bevel angle adjustment 15 to 45 ° bevel width continuously adjustable 0 to 7 mm length of guide bar 500 mm speed 2750 rpm drive 400 V / 0,7 kW space requirement approx. W 650 x D 600 x H 950 mm Weight approx. 30 kg Lsdjk H D Dfopfx Ab Uoah

Year of construction: 1988, condition: good (used), machine/vehicle number: 73480-08, Offer 22679 Technical data: - max. sheet thickness 50 mm - min. straight edge 3 mm - bevel angle adjustable 25 - 55 °. - working speed 1,5 - 3,1 m/min - crane hanger - drive 400 V / 4 kW - space requirement approx. W 1400 x D 1200 x H 1950 mm Ljdokzhawjpfx Ab Usah - Weight approx. 1500 kg