Round bending machine

MEGEY MRM 90-15/2,5

Condition: new, sheet thickness steel (max.): 4 mm, - Capacity 4 mm - Adjustment of the hydraulic roller - foot switch - Brake motor - With 4 roller sets - Emergency stop - 400V Itjdpfxogg Nq Ho Ah Nob

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Itodpfx Ajflk Awoh Nob Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: excellent (used), Year of construction: 1999, Used Large Format Trumpf 500r 1600 throat Cnc Punch Press For Sale TRUMPF TRUMATIC T500R Large format rotation cnc punch press for sale This machine will process 3metre x 1.5metre sheet without a reposition. Trumpf uk specification: Brand: TRUMPF Model: TRUMATIC 500R Type: CNC Punching Machine Control: Bosch CC220 Punching force (ton)22 Capable of taking multi tool Trumpf TC 500R Turret Punch 3000 X 1500mm large format machine 1600 throat x 3metre rail. TRUMPF TRUMATIC 500 CNC PUNCH WITH CONTROL & AIR TABLE CAPACITY: 220KN SERIAL Itodpfxotltl Hj Ah Nsb YEAR: 1999

Condition: refurbished (used), Year of construction: 2010, load capacity: 200 kg, arm reach: 2,400 mm, As PLC Merkezi, we can conduct custom engineering projects with our industrial robots in our stock like this example. We can help you with: - Welding - Cutting - Machine Feeding - Palletising - Depalletising - Marble Processing - Apgant Machine Feeding and Metal Bending - And many other projects Brand: KUKA Model: KR200-3 Comp Condition: Refurbished with 1 year of warranty Version: V5.6.12 Year: 2010 Control Cabin: KRC2 ed 05 Rated Payload: 200kg Access Distance: 2400mm Included: Manipulator + Control Cabin + All Wiring Sets + Teach Pendant +1 Hertz Spindle Motor (New) + Delta Spindle (Set with the Mechanical System) + Tool Changer Table Isdpoq Dpxdsfx Ah Notb Not Included: 7th Axis, Engineering Design and Consultancy Shipping: NOT included in the price Payment: 100% payment before collection

Condition: new, Year of construction: 2025, -TFON Leveltech® Leveling Machine Series -Model: L-9060. -Material Thickness: 1.0 mm – 30.0 mm. -Maximum Material Width: 600 mm -Minimum Material Length: 145 mm. -Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled Overload Protection: Standard Machine Weight: 26.000 kg. Machine Dimensions (L × W × H): 4,400 × 7,185 × 2,260 mm Model: L-9011 Material Thickness: 1.0 mm – 30.0 mm. Maximum Material Width: 1,100 mm. Minimum Material Length: 145 mm Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled Overload Protection: Standard Machine Weight: 31.000 kg Machine Dimensions (L × W × H): 4,600 × 7,185 × 2,260 mm Model: L-9013 Material Thickness: 1.0 mm –30.0 mm Maximum Material Width: 1,300 mm Minimum Material Length: 145 mm Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled Overload Protection: Standard Machine Weight: 35,000 kg Machine Dimensions (L × W × H): 5,000 × 7,185 × 2,260 mm Model: L-9016 Material Thickness: 1.0 mm –30.0 mm Maximum Material Width: 1,500 mm Minimum Material Length: 145 mm Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled. Overload Protection: Standard Machine Weight: 40.000 kg Machine Dimensions (L × W × H): 5,200 × 7,185 × 2,260 mm Model: L-9020 Material Thickness: 1.0 mm –30.0 mm Maximum Material Width: 2,000 mm Minimum Material Length: 145 mm Flattening Gap Adjustment: Servo Hydraulic / PLC Controlled. Overload Protection: Standard Machine Dimensions (L × W × H): 5,700 × 7,185 × 2,260 mm. Itedpfx Ahshwb U Ts Neb

Condition: good (used), Year of construction: 1986, machine/vehicle number: 8618030, Offer 25182 Technical Data: Iedowq It Tepfx Ah Njtb - Max. working width: 2040 mm - Max. material thickness: 4 mm - Roller diameter each: 140 mm - Stroke: 70 mm - Rear roller and bottom roller adjustable for conical bending - Upper and lower rollers driven by motor - Working speed right + left: 6 m/min - Drive: 380 V / 6.2 kW - Space requirement approx.: W 3560 x H 1100 x D 870 mm - Weight approx.: 1700 kg - With: - asymmetrical roller arrangement - crown-turned naturally hardened rollers - manual adjustment of rear rollers - pre-bending - pivotable top roller - electric foot switch for right and left rotation

Condition: new, GRATMAXX Bürstentgratmaschine The machine is suitable for the deburring of edges on: Round tubes, square tube, rectangular tube, full materials, profiles of all kinds. Materials: Steel non-ferrous metals, plastics, hard or soft. Work flow: After setting the workpiece support and dern side stops the Ridge-workpiece is easily kept on the brush rotating around its own axis, without rotating the workpiece, this movement is also the brush. The workpiece material, the Ridge strength, as well as the desired rounding of the edges determine the pressure and the duration of contact seconds, usually around 1-5. Technical data: Material: Steel, stainless steel and non-ferrous metals (engine speeds 700-1,900 rpm, infinitely variable) Min. workpiece-Ø: 5 mm Maximum work piece-Ø: 100 mm (150 mm) Brush dimensions: 2 piece Ø300 (250) x 50 or 3 piece Ø 300 (250) x 35 Power: 3,0 KW Power: 3.5 KW Operating voltage: 3 ~, 400Volt, 50 Hz Rated current: 8A Back-up fuse: max 16A Itodpfod Hmnfsx Ah Nsb Control voltage: 24V/DC Width: approx. 500 mm + Handwheel 74 mm, + dust spout 130 mm Altitude: 1.382 mm Working height: approx. 1.080 mm Depth: 1,209 mm Weight: 310 kg Sound pressure level: At speed 700 rpm 64 dB(A) at a speed 1500 rpm 74 dB(A), when machining a workpiece with maximum speed of 82 dB(A) Scope of delivery: Rotary head Bürstentgratmaschine GratMaxx with power socket without cable Workpiece support table with adjustable angle stop and

Condition: new, messurements (LxWxH): 1.630 x 700 x 1.200weight approx.: 480total power requirements: 1,1prebending: 2sheet thickness: 3sheet length: 1050 Itsdjd Eqqqjpfx Ah Nob

Condition: used, Pneumatic folding and edging machine FASTI Type 606 - 11 - 1.0 Folding machine for pre-forming sheet metal seams For producing a seam bend Seam bending machine for thin sheet metal as an alternative to a press brake Serial no.: 9166002 Year of manufacture: 1991 Working length: 1100 mm Material thickness at 45 kg/mm²: 1 mm Compressed air requirement: 6 bar - pneumatic foot switch - roller adjustment via threaded clamping screws Required space (L x W x H): 1600 x 300 x 1050 mm Weight: approx. 250 kg Good condition Itjdpfedzqblox Ah Njb The seam is the doubling over of the sheet metal edge (1x folded over) to increase the stiffness of the sheet. By folding over, a rounded edge is created, reducing the risk of injury from sharp sheet edges. Ideal for metalworking applications such as sheet metal furniture, cladding panels, or for the production of ventilation and silencer components.

Condition: good (used), Drying oven for uv line Iedpfx Ast Ag Uqjh Notb