HELLER MC 2000

HELLER MC 2000

Condition: good (used), Year of construction: 2011, Ref. -No.: 10598 Manufacturer: HELLER Type: MC 2000 Year of construction: 2011 Type of control: CNC Control: Siemens 840 D sl Storage location: Halberstadt Country of origin: Hermany Machine-No.: 50XXXX X-Travel: 800 mm Y-Travel: 800 mm Z-Travel: 1000 mm Work spindle torque (25% ED): 242 Nm Tool Taper: SK 40 Numbers Of Tools In Magazin: 54 Tool Piece Magazine With: 80 Pcs./pcs. Turning Speeds: 10000 RPM Drive Capacity - Spindle Motor: 17 kW High-Pressure Pump: 50 bar Speed range - main spindle: 10000 RPM Numbers Of Pallets: 2 Size Of Pallet: 630 x 500 mm Weight Of The Machine Ca.: 13000 t spindle running time: 7000 H Operating hours: 14000 H Preparation area: 4 x 90° hydraulic pressure: 200 bar Further information: Lodpfx Adex Hn D Rs Njhb - The machine has been measured - The geometry is in excellent condition - The spindle runs a little rough - Clamping towers and cutting tool holders are also included - 2 additional clamping towers - 2 replacement pallets - 2-axis servo tool changer - Scraper conveyor for dry machining - Cold light in the work area - Central cooling unit for motor spindle and control cabinet - Control unit at the workpiece setup station - NC-controlled rotary table - Clamping hydraulics The machine can be viewed under power by appointment.

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, turning length: 810 mm, turning diameter over cross slide: 800 mm, turning diameter: 320 mm, spindle motor power: 25,000 W, spindle speed (max.): 5,000 rpm, spindle bore: 73 mm, travel distance X-axis: 210 mm, travel distance Y-axis: 110 mm, travel distance Z-axis: 810 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 20 m/min, rapid traverse Z-axis: 50 m/min, rotational speed (max.): 6,000 rpm, CNC FANUC MSX-701 / MAPPS IV CAPACITY Swing diameter over bed: mm 800 Swing diameter over cross slide: mm 800 Maximum turning diameter: mm 320 Standard turning diameter: mm 200 Maximum distance between the center: mm 1.130 Maximum turning length: mm 810 Maximum workpiece size: mm 300 TRAVELS X axis turret 1 and 2: mm 210 Y axis turret 1 and 2: mm +65 / -45 Z axis turret 1 and 2: mm 810 B axis headstock 2: mm 920 MAIN SPINDLE Maximum speed: rpm 5.000 Drive power (30 min / continuous operation): kW 25/22 Maximum bar diameter: mm 65 Spindle bore: mm 73 Spindle diameter in front bearing: mm 120 Spindle mount: JIS A2-6 C-axis resolution: degrees 0,001 SUB SPINDLE Maximum speed: rpm 5.000 Drive power (30 min / continuous operation): kW 25/22 Maximum bar diameter: mm 65 Spindle bore: mm 73 Spindle diameter in front bearing: mm 120 Spindle mount: JIS A2-6 C-axis resolution: degrees 0,001 FEED DRIVES Rapid traverse turret 1 X/Y/Z: m/min 30/20/50 Rapid traverse turret 2 X/Y/Z: m/min 30/20/50 TOOL TURRET Number of turrets: 2 Number of tool stations per turret: 16 Shaft cross – section for turning tools: mm 20 x 20 Maximum shaft diameter for boring bars: mm 32 Turret switching time (1 station): s 0,18 Maximum speed of the driven tools: rpm 6.000 Drive power for driven tools (5 min/continuous operation): kW 7,5/5,5 DIMENSIONS Installation area with chip conveyor: mm 5.120 x 2.720 Net weight: kg 8.300 Macchina equipped with: • High pressure cooling system • Bar loader interface Lhodpfxswlvlgj Ad Nob • Gantry-type piece unloading arm • Cutting effort management system and load monitor • No. 1 double radial motorized tool holder • No. 3 axial motorized tool holders • No. 2 external tool holders • No. 2 double boring bar holders • No. 2 single radial motorized tool holders • No. 2 internal boring bar holders • No. 2 Kitagawa BD 208 self-centering chucks diam. Mm 210 • No. 1 set of jaws for each self-centering chuck • Instruction manuals and CE declaration Year of manufacturing: 2010

Condition: used, Year of construction: 2012, x-travel 1.035 mm y-travel 560 mm z-travel 510 mm CNC-control HEIDENHAIN TNC620 table-size 1200 x 560 mm max. table load 1000 kg spindle taper SK 40 spindle turning speed range 10.000 U/min drive capacity - spindle motor 13 kW feed stepless 20.000 mm/min rapid traverse 25 m/min tool change unit 20 Pos. coolant IKZ 20 bar voltage 400 V total power requirement 17 kVA weight of the machine ca. 4,1 t dimensions of the machine ca. 2,55 x 2,30 x 2,25 m chip conveyor 3,90 x 0,95 x 1,60 m - Serial No.: 1539000377A - Machine ON: 21.689 h - Program Run: 9.021 h - CNC-Control: Heidenhain TNC620 Lsdsw A Spvopfx Ad Nohb - elektronic hand wheel - chip conveyor - coolant through spindle 20 bar

Condition: good (used), Year of construction: 1989, operating hours: 64,136 h, Centre height: 350 mm Turning length: 1000 mm Max. swing diameter over bed cover: 600 mm Max. swing diameter over cross slide: 360 mm Spindle bore: 107 mm Speed range: 16 – 3150 rpm Feed range longitudinal & face: 0.5 – 5000 mm/min Rapid traverse longitudinal & face: 9 m/min Main drive: 30 kW Dimensions of machine with chip conveyor (L x W x H): 5400 x 2200 x 2000 mm Weight: 6400 kg Accessories / Special features: • CNC control GILDEMEISTER EPL 2 with TFT display General description: CNC manual input control system with program entry via function and numeric keypad. All information is entered in dialogue with the screen. Integrated menu technology with plain text display of all functions. Operator keypad, display, and electronic handwheel located within a separate chip guard housing. The EPL control offers the following capabilities: • Direct interactive program entry and editing by the operator through the EPL control without manual technological preparation • NC programs in ISO/EIA format can be entered, output, or manually keyed in via the RS 232 serial interface Machining cycles: • Removal cycles for longitudinal, facing, and contour turning, including with allowance • Thread cutting Ljdpfovr Eh Eex Ad Nshb • Undercuts as per DIN 509-Form E and F and DIN 76; grind stock programmable • Axial and radial grooves as per DIN 471 and 472, including bottom finishing • 90° radii and 45° chamfers • Automatic cutter radius compensation for cycles, undercut, groove, radius, chamfer Programming: • Block-orientated, metric/inch, diameter for absolute entry, radius for incremental entry • Full circle programming, subroutine technology, hide levels for program sections, zero point offset, mode selection via menu Program entry and output: • Interactive via guided menu or direct in dialogue • Hydraulic 3-jaw chuck Ø 315 mm with through spindle bore Ø 80 mm • Hinged chip conveyor • 12-position tool turret VDI 40, 6 standard stations + 6 driven tool stations • Coolant system • RS 232 interface • Electronic handwheel • Electric foot switch for 3-jaw chuck and tailstock quill • Lighting • 12 various standard toolholders (to be finalized on site) Overhauled servo drive for main spindle, 06/2025 Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: used, Year of construction: 1997, travel distance X-axis: 3,708 mm, travel distance Y-axis: 1,208 mm, travel distance Z-axis: 1,002 mm, feed length X-axis: 5,000 mm, feed length Y-axis: 5,000 mm, feed length Z-axis: 5,000 mm, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 15 m/min, spindle speed (max.): 3,000 rpm, spindle speed (min.): 35 rpm, CNC Bed-Type Milling Machine – Universal ZAYER 20 KF 4000 Year of manufacture: 1997 CNC control: HEIDENHAIN TNC 426/430 Technical specifications: X travel: 3708 mm Y travel: 1208 mm Z travel: 1002 mm Table size: 4000 x 1000 mm Tool holder: SK 50 Spindle speeds: 35–3000 rpm Spindle motor: 22 kW Feed range: 6–5000 mm/min Rapid traverse: 15 m/min Machine weight: approx. 19.5 t ADDITIONAL INFORMATION Electronic handwheel Lhjdpfx Adjwtpfpj Neb Automatically swivelling milling head vertical/horizontal +/-120° (stepless) Milling head automatically swivelling in the rear axis / 90° rotation Coolant system The machine can be inspected under power. Delivery time: immediately Sale from location Westerkappeln Dismantling, loading available on request.

Condition: used, Year of construction: 2014, max. turning diameter 160 mm max. turning height 150 mm max. workpiece diameter 100 mm max. workpiece height 150 mm max. turning speeds 6.000 U/min travel -x axis 700 mm travel -z axis 375 mm c-axis 360 ° control FANUC Vertical Turning Machine | EMAG - VL2 equipped with a workpiece conveyor belt. The machine is in very good condition. Please note that the technical details were added from comparable machines. Lhsdpfxeqvd Iqj Ad Njb - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: VL-2 | VL 2

Condition: used, Year of construction: 2007, turning diameter 300 mm turning length 600 mm control FANUC, 18i-TB turning diameter over bed slide 230 mm travel x1 165 mm travel z1 700 mm travel x2 190 mm travel z2 720 mm travel -y axis +/- 50 mm main spindle bore 76 mm main spindle speed 5.000 U/min main spindle drive 22 kW max. torque on the spindle 208 Nm sub spindle bore 76 mm sub spindle speed 5.000 U/min sub spindle drive 22 kW max. torque on the spindle 208 Nm tool turret 2 x 12 Stat. number of driven tool stations 2 x 12 speed of driven tools 5.000 U/min max. torque 47 Nm work piece power 5,5 kW C-axis resolution 0,001 ° rapid traverse x + z axis 20 / 40 m/min rapid traverse y-axis 7,5 m/min total power requirement 68,4 kVA weight of the machine ca. 7,8 t Accessories: collet fixture on main spindle, hydr. 3-jaw chuck make KITAGAWA, BB 208, 210 mmø, on sub spindle, Ljdpjxn Amtjfx Ad Nehb various tool holders for turret, bar loader make HYDRAFEED, model MULTIFEED MX-1B for bar dia. 3 - 80 mm and bar length up to 1650 mm, chip conveyor, coolant with belt filter device

Condition: used, Year of construction: 1969, max. wheel diameter 160,175 mm gear width 355 mm max. module 4,5 spindle bore 75 mm centre distance 410 mm min. number of teeth 2, 3 cutter diameter max. 115 mm cutter length max. 105 mm axis distance between cutter and workpiece - max. 138 mm axis distance between cutter and workpiece - min. 30 mm milling head -swivable 120 ° milling spindle speeds 70 - 400 U/min axial-feeds 0,25 - 4,0 mm/U radial feeds 0,09 - 1,5 mm/U total power requirement ca. 9,5 kW weight of the machine ca. 3,5 t dimensions of the machine ca. 1730x1400x1440 mm Lhjdpovzhf Sefx Ad Nob Equipment/accessories: - Interchangeable wheels - Milling arbors - Clamping devices - Documentation

Condition: excellent (used), Year of construction: 1998, CNC Lathe Gildemeister CTX 200 E Year of manufacture: 1998 Heidenhain CNC Control Lhedow I Swcjpfx Ad Njb Technical Data: CNC Control: Heidenhain Maximum turning length: 350 mm Maximum turning diameter: 160 mm Maximum bar diameter: Ø 42 mm Tool turret capacity: 12 positions (driven) Maximum spindle speed: 5000 rpm Spindle drive power: 7.5 kW Equipment of the CNC Lathe: Chuck spindle Driven tools Bar feeder: IEMCA VIP 70 CNC Tool holders and jaws

Condition: used, Year of construction: 2013, Technical details: x-travel: 760 mm y-travel: 460 mm z-travel: 460 mm control: Heidenhain TNC 620 switched on hours: 20246 h spindle hours: 7724 h Lhsdpfx Adevhbpdj Neb number of spindle speeds: 12.000 U/min. max. torque on the spindle: 75 - 95 Nm spindle taper MT: SK40 tool changer with: 24 Plätze table-size: 900 x 410 mm max. table load: 350 kg feed range: k.A. rapid traverse:: 36 m/min interface: RS232 control voltage: 24 DC V air-pressure connection: 6 / 8 bar total power requirement: 20 kVA Weight approx.: ca. 6,0 t dimension coolant device: 1,7 x 0,7 x 1,35 m dimension machine xH: 1,9 x 2,3 x 2,45 m TNC620 (contouring control with up to 5 controlled axes, particularly suitable for universal milling), can be integrated into the network Safety doors with impact-resistant plastic window panes Chip conveyor Hydraulic unit Coolant preparation system Rittal cooling system on the control cabinet Work area Interior lighting *