Band Saw

FEMI N 251 DA XL

Condition: used, Wig welding machine L-TEC, Inverter TIG 200 DC type WIG welding machine for direct current DC Njdpodzqb Ejfx Ag Islh Serial no. 184548, year of manufacture approx. 1994 Power: 200 Amps = 60% duty cycle 155 Amps = 100% duty cycle Adjustment range: stepless Current type: DC (direct current) Mains connection: 400 Volts, 50 Hz, 32 Amps plug - 4 meter hose set with central connection and hand torch - with remote potentiometer (foot switch) - gas pressure regulator - DC only - HF ignition Space requirement L x W x H: 850 x 480 x 740 mm Weight: approx. 150 kg The welding test yields very good results when welding stainless steel with direct current. Otherwise in good condition.

Condition: new, cutting diameter 235 mm dimensions of saw-band 2645 x 27 x 0,9 mm cutting width 280 x 190 mm cutting speed 45/90 m/min 120 mm 120 mm 190 mm Impact energy 170 mm connected load frequency 400 Volt total power requirement 1,1 kW weight of the machine ca. 290 Kg Nodpfxsp Scqys Ag Ielh dimensions 1,2 x 0,8 x 1,2 m Double miter band saw -Miter cuts up to 60° left and 45° right -Vice with quick clamping device -Band tension control -Electr. Automatic cooling

Year of construction: 2004, condition: good (used), machine/vehicle number: 0441057, Offer 23300 Technical data: - Sanding belt dimension 75 x 2000 mm - surface grinding opening 75 x 300 mm - support vice - angle adjustable 90° - 30 ° - grinding belt speed 15 + 30 m/sec. Nljdpspug D Eofx Ag Ieh - possible contact rolls Ø 20 - 76 mm - contact roller length 75 mm - drive 400 V / 2,2 / 3 kW - drive speeds 1440 / 2880 rpm - 1 piece contact roll 48 mm - space requirement approx. W 800 x H approx. 1000 x D 1300 mm - weight approx. 250 kg

Condition: new, Year of construction: 2026, The CORMAK HBS275 band saw for cutting tubes, profiles and bars is widely used in all locksmith and metalworking workshops where precision, quality and cutting speed matter. The model is equipped with a 0-60° swivel arm; the saw guides are based on sintered carbide. The frame construction ensures accurate and quiet operation. Machine characteristics The horizontal metal band saw with swivel arm enables cutting in a plane perpendicular to the axis of the material being cut and at any angle within the range from 0 to 60°. The material to be cut can be fed manually or by any mechanical device, while the tool feed is automatic. The blade guides are equipped with special carbide plates and bearings. This has a major impact on blade guidance, service life, straightness, accuracy and cutting quality. Carbide guidance greatly reduces wear of the machine and blade. The machine is equipped with an efficient coolant pump with a closed coolant circuit. The saw arm is made of a single cast-iron casting and, together with the 27 mm wide cutting blade used in this saw, fully enables multi-series cutting of both profiles and solid materials. The vice is located in an adjustable bed and is equipped with a quick clamp. The blade guides are equipped with hard metal plates – sintered carbide and a rolling bearing system. It is precisely the SINTERED CARBIDE GUIDES that are responsible for the precision and straightness of the cut. The arm has been inclined at an angle of 25°, which increases blade durability and improves cutting conditions. A cleaning brush is mounted at the bottom of the arm to achieve excellent cleanliness and blade operation. The machine drive is transmitted via a worm gearbox. The machine has a three-phase motor with two cutting speeds and motor thermal protection. The shape of the upper part of the base forms a tray for draining coolant and collecting chips generated during material cutting. A cast-iron work table with a swivel arm and a control panel on a separate arm is mounted to the base. In the cutting process, the main cutting movement is the movement of the cutting blade, while the feed is the lowering of the arm. The arm lowering speed (cutting speed) is regulated by a hydraulic cylinder. The feed speed is adjusted on the saw control panel. Two cutting blade speeds are available: 37.5 and 75m/min. In the lower position of the arm (after cutting the material), the cutting blade drive is switched off automatically. Safety is ensured by cutting blade guards and micro-switches that stop the motor after the cutting cycle is completed or when any guard is opened; additional protection consists of automatic shutdown of the saw in the event of cutting blade breakage. The machine drive is transmitted by a motor with a worm gearbox. The motor with thermal fuse protects against overheating during operation. Technical data TOTAL POWER 1.5kW POWER SUPPLY 400V 50Hz ARM LOWERING ADJUSTMENT hydraulic cylinder BLADE LENGTH 2450 x 27 x 0.9 mm BLADE SPEED Njdpfxjudi Une Ag Ijlh 37.5 / 75m/min VICE BASE HEIGHT 900 mm MACHINE DIMENSIONS (WITH ARM RAISED) (L x W x H) 1720 x 800 x 1800 mm WEIGHT 215 kg

Condition: new, cutting diameter 355 mm dimensions of saw-band 3770 x 34 x 1,1 mm cutting speed 20 - 80 m/min cutting width 490 x 280 mm 290 mm Impact energy 250 mm 230 mm 180 mm connected load frequency 400 Volt total power requirement 2,2 kW weight of the machine ca. 0,7 t Njdpfx Agemhm Aqs Islh dimensions 1,43 x 0,72 x 1,7 m Semi-automatic miter band saw - Miter cuts up to 45° left + right - Miter cuts up to 60° right - Vice with quick release device - Tape tension control via manometer - Electr. automatic cooling

Condition: new, Year of construction: 2022, IN STOCK -- The ARG 235 plus is a manual metal bandsaw with high cutting accuracy. This machine allows miter cuts from -45° to +30° continuously (swivel range left 45° and right 60°) Technical Specifications: ● Cutting range: - 90° round: 235 mm / square: 230 mm / rectangle: 280 x 180 mm - 45° Right round: 165 mm / square: 145 mm / rectangle: 185 x 180 mm Nledpfxjmftv Rs Ag Ieh - 30° Right round: 115 mm / square: 80 mm / rectangle: 115 x 80 mm - 45° Left round: 185 mm / square: 160 mm / rectangle: 185 x 100 mm ● Drive Power Saw Blade: 0,9 / 1,4 kW / 400 V / 50 Hz ● Saw Blade Speed: 40 and 80 m/min ● Saw Blade: 2710 x 27 x 0,9 Standard Equipment: ● Powerful saw blade drive ● Stepless adjustment of the cutting feed from the control panel ● Manual clamping of the workpiece, movable clamping stock with dovetail guide ● Easy adjustment of the saw for miter cuts by rotating the saw frame (stops at 45°, 60°, and 90°) ● 250 mm material stop without scale --> Also available in different sizes or versions!

Condition: excellent (used), Year of construction: 2002, Control: 3-axis active path control, Heidenhain TNC 123 Spindle speed: 40 - 2000 rpm, geometrically stepped direct drive with 16 gear stages for maximum torque / milling performance Feed rate: 5 to 500 mm/min, infinitely variable Rapid traverse: 1.2 m/min Quill: Extendable vertical quill, 60 mm, SK40 M16 draw thread Nlsdpfx Ageyg I Nfs Ish Axes X/Y/Z: 300/160/340 mm Swivel table: 600 x 210 mm, max. load 200 kg

Condition: new, cutting diameter 225 mm saw band length 2455 mm table height 850 mm cutting width 245 x 150 mm cutting speed 45/90 m/min dimensions of saw-band 2480 x 27 x 0,9 mm 90 mm 90 mm 145 mm Impact energy 145 mm connected load frequency 400 Volt total power requirement 1,5 kW weight of the machine ca. 0,2 t dimensions 1,43 x 0,72 x 1,7 m Nodpfxogxi D Te Ag Iolh Miter band saw -Miter cuts up to 60° left -Vice with quick clamping device -Band tension control -Electr. Automatic cooling

Condition: new, WMD25LV - 230V / 1Ph Drilling capacity in steel ----- 25 mm Milling capacity in steel ----- 20 mm Face milling ----- 63 mm Motor ----- Brushless 750W Spindle speed, continuously variable 50 - 3000 rpm Spindle stroke ----- 50 mm Spindle taper ----- MK3 Work table ----- 700 x 180 mm Cross travel ----- 150 mm Longitudinal travel ----- 490 mm T-slots ----- 3x12 mm Overhang ----- 170 mm Distance spindle - table ----- 325 mm Weight ----- 160 KG STANDARD ACCESSORIES * Drill chuck incl. chuck key * Digital depth stop Nlodpfx Agega T Eij Ijh * Digital spindle display * Fine adjustment * Left / Right switch * Milling head, left / right, rotatable 90 degrees * Box with various tools OPTIONAL * Base cabinet € 249.00 excl. VAT

Condition: like new (used), functionality: fully functional, Year of construction: 2021, operating hours: 417 h, Amada HFE M2 5012 Press Brake (2021) Manufacturer: Amada Type: HFE M2 5012 Press Brake Condition: used, currently in production Year of manufacture: 10/2020 Operating hours: 6830 h Working hours: 417 h (still in use) Pressing force (kN): 500 Press beam length (mm): 1270 Distance between machine uprights (mm): 1035 Stroke (mm): 150 Opening width without die holder (mm): 480 Overhang (mm): 100 Working height (mm): 920 Working speed (mm/sec): 15 Approach speed (mm/sec): 185 Opening speed (mm/sec): 185 Dimensions: Nsdpfx Aezwppyeg Islh Length (mm): 2585 Width (mm): 2190 Height (mm): 2420 Weight (kg): 3600