1993 Emmegi Sirio 2

Emmegi Sirio 2

Condition: used, Year of construction: 2023, DOUBLE GLASS BEAD SAW TRF 527 VIS CE 1 pc DOUBLE GLASS BEAD SAW TRF 527 VIS CE TRF 527 VIS: Double miter saw for the simultaneous cutting of two glass beads positioned one above the other. The right saw unit is fixed, adjustment of the left unit is via the set cutting length can be read off a digital display. The units have supports that allow two glass beads to be cut simultaneously. The upper support can be removed for cutting larger cross-sections. After the cutting process is completed, the pneumatic clamping cylinders automatically swing to the side to simplify loading and unloading of the machine. STANDARD EQUIPMENT • Fixed unit on the right • Digital dimension display • Pressure switch • 2 HM-tipped saw blades • Electrical system with motor brake, undervoltage release, motor protection switch • Pressure switch • Tool set • Guards with horizontal clamping devices, pivoting • Two-hand control • Belt drive • Pneumatic unit lift • Middle support TECHNICAL DATA • Motor power 2 x 1.2 kW • Saw blade diameter Ø 220 mm • Max. cutting height without support 80 mm • Max. cutting width at 90 degrees 55 mm • Max. cutting width at 45 degrees 40 mm • Max. cutting length 2800 mm (optional 4000 mm) • Min. cutting length 158 mm • Weight 217 kg • Space requirement (standard equipment) 3000 x 850 mm Extended cutting capacity 1 pc Maximum cutting length • 4000 mm Star stop 4 positions 1 pc set 2 mechanical stops for adjusting up to 4 intermediate angles. Additional center support. 1 adjustment for rebated profiles. 1 adjustment for rebated profiles as per drawing: - Attachment to the clamping devices to compensate for the profile inclination - Allowances on the rear stops of the units and the center support. The sketch below shows (in green) a beveled presser that follows the inclined profile and presses it against the allowance on the stop (shown in red). Storage location: Garbsen Gusdpfx Anjxnlgcekob

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 901 S Pnömatik Alüminyum Köşe Presi Makinası, - Conforms to CE standards Godpfsrbiv Asx Ankeub - Corner press machine designed for 90 degree joining of aluminum profiles - 2 top presses and blade movement is pneumatic - There is a mm ruler system for the height and advancement of the blades. - Centering miter wedge is automatic - Drain button available for fine adjustment - Pneumatic presses use 2 pedals to squeeze the profile - Profile surfaces are polyamide sheet to prevent damage - Side support arms available

Condition: new, Year of construction: 2026, crosscut and miter saw type: ZS 200 N - 5 KW motor with machine stand, but without saw blade Machine via handwheel and worm gear (rear) Tiltable Saw blade diameter 520 mm, saw blade mounting hole 50 mm Saw blade speed: 2800 rpm 400 volt / 5 KW (S6/40%) motor with brake u. Automat. Star delta motor control cutting width at 90deg: 420 mm cutting width at 45deg: swivelled: 295 mm Gedpfx Asi Dfidsnkjub Cutting height at 90deg: 200 mm Cutting height at 45deg tilted: 140 mm Saw can be tilted on one side up to approx. 25 degrees to acute angles and tilted flat to the left up to 30 degrees Machine stitched: approx. 250 kg Location: ex stock 54634 Bitburg - immediately available -

Year of construction: 1985, condition: good (used), Offer 22556 Technical data: - Saw blade diameter 420 mm - saw blade bore 30 mm - max. cutting length 3000 mm - smallest cutting length at 90° + 45° 335 mm - cutting range see diagram enclosed - tilting range inwards manual 90 - 22,5 ° Gsdpfx Anjimdlrekoub - inclination range inward manual 90 - 45 ° - Saw blade speed 2800 rpm - drive 380 V / 2 x 4000 Watt - Compressed air supply 7 bar - Air consumption per working cycle approx. 64 l - space requirement approx. W 4500 x H 1950 x D 1600 mm - weight approx. 1400 kg - with: - cutting length adjustment with positioning control - positioning control renewed approx. 2002 by WOLFF - saw unit swiveling and tilting for high and wide profiles, - as well as shift cuts

Condition: used, Year of construction: 1994, Technical details: saw blade diameter: 450 mm Gedpeu Nigksfx Ankoub revolution per minute: 2820 U/min cutting lenght max.: 5000 mm cutting length min.: 240 mm air pressure - required: 6-8 bar hole of sawblade: 32 mm mitter cutting - both sides: 45+90 ° air-pressure connection: 6 - 8 bar total power requirement: ca. 4,6 kW weight of the machine ca.: 1,1 t dimension machine xH: 6,05x1,49x1,79 m Further features of the machine: - Pneumatic vertical and horizontal tension - pneumatic mist spraying device - height adjustable machine feet - material supports movable with saw - piece counter Cutting diameter according to tabular cutting range diagram, as dependent on speed and saw blade. Accessories: - 2 spare saw blades Machine can be demonstrated under power. i.D. *

Year of construction: 2004, condition: good (used), machine/vehicle number: 2004-3-11A, - Manual feed of the milling unit - Work table height adjustable via hand wheel - horizontal and vertical material tension - Cutter diameter up to 250 mm - max milling height 150 mm - max milling depth 80 mm - max milling length 305 mm - angle adjustable stop Li + Re 20 - 90 ° - milling spindle speed 4500 rpm - Drive 400 V 3.2 kW - Compressed air supply 6 - 8 bar - Air consumption per working cycle 10 l - Pneumatic profile clamping Guedof E Higspfx Ankob - Table underframe - Space requirement approx. W 1100 x H 1300 x D 700 mm - Weight approx. 200 kg

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 902 S Hidrolik Alüminyum Köşe Presi Makinesi, • Complies with CE standards • Corner press machine designed for joining aluminium profiles at 90 degrees • 2 upper presses and blade movement are hydraulic • Equipped with a mm scale system for adjusting blade height and feed • Centering square stop is hydraulic • Drain button for fine adjustment is available • Machine comes with 2 pieces of 4 mm blades Guedpfx Anjrbk Tfekob • 2 pedals are used for hydraulic pressing and profile clamping • Polyamide plate is provided to prevent damage to profile surfaces • Left and right profile support arms are available

Year of construction: 1987, condition: good (used), for cutter Ø up to max .: 300 mm Saw stroke adjustable by hand: 550 mm Infeed by hand via spindle: 150 mm Height adjustment by hand via spindle approx .: 130 mm Table semicircle Ø: 500 mm Guedpfx Aneghl Emekjb Saw blade drive: 380 V, 2.2 kW Saw blade speed: 2700 rpm Space requirement approx .: 1000 x 900 x 1300 mm Weight approx .: 100 kg

Condition: used, Stop for chop saw, pull saw, stop and measuring system -Manufacturer: elumatec, stop and measuring system with digital display -Inclusion: Bosch profile -Length unit: 4280 mm -Price: complete -Dimensions: 4710/510/H635 mm Guodpoinwuqofx Anksb -Weight: 72kg

Year of construction: 2012, condition: excellent (used), functionality: fully functional, - Power (kW): KFB 353 = 1.5 - Voltage (V): 400 - Air pressure (bar): 7 - Air consumption (l/min): min. 250 Guedewzivdjpfx Anksb - Revolution shaft (min-1): KFB 353 = 12,000 - Maximum cross section of the workpiece WxH(mm):190x111 - Milling range L x W (mm): 300 x 130 - Milling depth (mm): 200 - Machine dimensions L x D x H (mm): 3,500 x 820 x 1,650 Dpro2J - Weight (kg): approx. 420 - Workable material: KFB 353 = PVC and aluminum profiles