Rotary Welding Table

DUMETA D-HB-HE-30

Year of construction: 2022, condition: new, Load capacity: 10.000kg Kdodpfx Ajfxgp Uegtel Speed: 0.03- 1.6 rpm faceplate diameter: 1.500mm, expandable to 2.500mm welding current transmission: 800A

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards Kedpfx Aoh Hm Tzogtedl -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg Ksdpehlz R Sofx Agtedl -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, functionality: fully functional, turning diameter over cross slide: 280 mm, spindle bore: 58 mm, turning diameter over bed slide: 470 mm, center height: 235 mm, turning length: 1,000 mm, quill stroke: 127 mm, quill diameter: 68 mm, total length: 2,150 mm, total width: 810 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 20 rpm, bed width: 300 mm, overall weight: 1,800 kg, quill mount: MK 4, Tip height: 235 mm Center distance: 1000 mm Spindle bore: 58 mm Spindle nose according to DIN 55029: Camlock D6 Motor power: 5.5 kW Spindle speed range: 20-2000 mm Kdsdpfjcirniex Agtol Features include Hardened and precision-ground Z-axis guideways Turcite coatings (on mating surface) of the tool and face slides Manual central lubrication with one pump for longitudinal and cross slides Complete coolant system with rear splash guard and splash guard on the slide Chuck guard Switch rod with 3 adjustable cams Machine light Fixed center point Set of machine mounting plates

Condition: good (used), Year of construction: 2000, CNC surface and profile grinding machine Fabr.Ziersch & Baltrusch Type:PROFITLINE ZB 62 NC Year of manufacture.2000 grinding range : 600X270mm Electromagnet with continuous transverse pole pitch Kodpfjfrbckox Agtodl 600X200mm. P = 4 mm Wet grinding device, with automatic paper belt filter, machine trough. Complete machine documentation available.

Condition: new, Year of construction: 2025, Genie GR20 Runabout vertical mast work platform, new, used, demonstration machines available Kdsdpfxsrh D R Ao Agtol

Condition: used, Universal Tool Milling Machine DECKEL Type FP 1 Machine No. 51265 Year of manufacture: approx. 1967 Travel paths X: 300 mm Y: 150 mm Z: 340 mm Table size 600 x 200 mm Spindle taper SK 40 - S20 x 2 Spindle speed 40–2000 rpm, 16 steps Kdjdpfx Aoghtvajgtjl Motor power 1.0 and 1.6 kW, pole-changing Power supply 380 Volt, 50 Hz - Feed on X and Z axes - Spindle speed via 2 motor speeds and 8 gear steps - Quill movement at vertical milling head 60 mm - Swiveling, rotating, and tilting angle table - Coolant pump in machine base - Separate control cabinet Space requirements L x W x H 1100 x 1100 x 1600 mm Weight 690 kg In good condition

Condition: new, Year of construction: 2025, load capacity: 20,000 kg, 20 tons container turning device, roller stand, complete set 380 V, speed infinitely variable from 200 to 1000 mm /min. for diameters from 500mm to 4000mm roller diameter 300mm x 140 mm temperature resistance of the support rollers 100° Double drive synkron AC motor, 380V 750 W with hand and foot remote control, complete set Kedpfx Ajifgu Usgtodl

Condition: used, Year of construction: 2016, machine/vehicle number: 0605-240010, FICEP Flex FRC 1201 coping robot The Ficep FRC 1201 coping machine is part of the latest process in automatic CNC controlled thermal coping process. This modern CNC-controlled coping robot system is suitable for fast thermal cutting and notching of profile types H / U / L / flat and square tubes. The steel profile is positioned in the system at the position to be cut using a pulling gripper measuring carriage via the roller conveyor. A robot arm with the cutting units (oxyfuel or plasma) cuts the profiles at the selected position. The cut or notched finished components either fall into the collecting tray or are pushed out of the system by the measuring arm. Thermal cutting units: This Ficep profile support notching system Flex FRC 1201 is equipped for thermal cutting with oxyfuel and/or plasma. A Hypertherm HYPERFORMANCE PLASMA HPR 260 XD suitable for material thicknesses up to 32 mm is used as the plasma power source. Thicker material thicknesses or phase cuts greater than 32 mm are cut with the oxyfuel cutting unit. Transport system: On the infeed side in front of the Ficep Flex FRC notching system is a chain drag cross conveyor with a length of 11,150 mm. The profiles (components) can be conveyed in both directions. The profiles are then transported into the machine on a stable roller conveyor with a gripper measuring carriage. The system is designed for 12 m long profiles and therefore has 12 m roller conveyors with a roller conveyor width of 1. 300 mm on the infeed side and 12 m on the outfeed side.300 mm. 4 chain tractors with a length of 6,450 mm are available after the notching system to transport the finished components to the outfeed side. Mitrol CNC control and Pegaso software: The system is controlled by a modern CNC control system from Mitrol. The reliable CNC control is from Ficep's own manufacturer Mitrol with the Pegaso software including remote maintenance option and data transfer interface. Torit DCE filter unit The filter unit for the dirt extraction is from Donaldson Torit DCE Safety: via fence and light barriers Max. profile cross-section: 1,220 mm. Profile cross-section : 1,220 x 600 mm Min. material length : 2,500 mm Working height : 865 mm Weight: 7000 kg Weight of cover firing unit : 1200 kg This modern Ficep Flex FRC 1201 coping robot system is in very good condition. Kodpfx Aotwm Ubjgtsdl

Year of construction: 2007, condition: excellent (used), 603 LBH Technical Description Main Technical Specifications • Minimum sawing capacity at 90° min.mm 60 x 10 max.mm 610 x 310 • Sawing capacity at 45° mm 400 x 310 • Sawing capacity at 60° (available on two flanges only with relevant option) mm 250 x 250 • Mitering angles +45° / -60° • Toothed band size mm 34 x 1.1 • Toothed band speed m/min. 78 Kdsdpjl Si Uujfx Agtsl • Band motor power kW 4 • Working level height mm 850