Eccentric press

ABM PREN-100

Condition: used, Year of construction: 1977, pressure 250 t stroke 40 - 190 mm no. of strokes 40 /min throat 500 mm passage to the back 1050 mm dayligth 615 mm table surface area 1380 x 880 mm hole in the table 450 mm table height over floor 800 mm ram surface 1200 x 800 mm Nsdsvuuaispfx Ah Hewb ram adjustment 125 mm power requirement 22,0 kW Weight 24,0 t dimensions of the machine ca. 2,0 x 2,5 x 3,95 m x m x m permitted for manual loading according to the German Safety Regulations (UVV) with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, pneumatic counterbalance in ram, motoric ram adjustment, manual stroke adjustment, motoric centralized lubrication, bolster plate, two-hand operation

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Nwedpfskvnumex Ah Heb Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 Nwedpfx Ajhlnzkjh Heb double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Nwodjg U Utvopfx Ah Hsb Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: new, Year of construction: 2025, pressing force: 100 t, stroke length: 400 mm, - Cylinder stroke 400 mm - Working width 1010 mm - Cylinder is movable - Can be operated electrically or manually Nodpfsgp Dc Rox Ah Hjwb - Pressure indicator - Emergency stop - 400V

Year of construction: 1980, condition: used, pressure 80 t throat - mm stroke 50 mm table surface area 875 x 695 mm ram surface 350 x 355 mm ram adjustment 71 mm no. of strokes 30 - 90 Hub/min distance between columns 450 mm weight of the machine ca. 6,2 t dimensions of the machine ca. 2,0 x 2,1 x 3,2 m daylight (stroke down, ram adjustment above) 480 mm Nedpodlcy Hjfx Ah Hswb Further information: - the machine is currently being a partially overhauled - the machine was re-equipped with the following components: * separate control cabinet with touchscreen including cabling * new painting of the individual components in the dismantled state After the partial overhaul, the machine is safe for manual insertion open tool, a current UVV test is carried out before delivery and braking time measurement.

Condition: used, Year of construction: 1969, max. wheel diameter 160 mm gear width 355 mm max. module 4,5 min. module 0,5 centre distance 450 mm total power requirement 11 kW weight of the machine ca. 3,8 t dimensions of the machine ca. 2x17,1,6 m Wheel diameter - max. 160.175 mm Wheel width 355 mm Module - max. 4.5 Spindle bore 75 mm Center distance 410 mm Number of teeth - min. 2, 3 Cutter diameter max. 115 mm Cutter length max. 105 mm Center distance between milling cutter and workpiece - max. 138 mm Center distance between milling cutter and workpiece - min. 30 mm Milling head - swivels 120 ° Milling cutter speeds 70 - 400 rpm Axial feeds 0.25 - 4.0 mm/rev Radial feeds 0.09 - 1.5 mm/rev Total power requirement approx. 9.5 kW Machine weight approx. 3.5 t Space requirement approx. 1730x1400x1440 mm Equipment/accessories: - Changing wheels Nwsdpjvz Ec Ijfx Ah Hob - milling arbors - Clamping device Dra8M7 - documentation

Condition: used, Double column eccentric punching press BLEMA Gotha type PEZ 160-50 MHSY-ES Eccentric press with roller feed ALBA Machine no. No. 88151005 Year of construction 1988 / 92 Pressure force 160 ton. Frame width 970 mm Stand width sideways 560 mm Table size 900 x 900 mm ram surface 900 x 700 mm Tool installation height 560 mm, max. 700 mm Stroke adjustment 8-160 mm Ram adjustment travel 125 mm Stroke rate 25 to 70 strokes/min. Belt width in roller feed max. 400 mm Motor power approx. 15 kW Mains connection 380 Volt, 50 Hz - Infinitely variable stroke rate via frequency control - Automatic stroke adjustment - ram weight compensation cylinder with compressed air - Hydraulic overload protection in the ram - Pneumatic clutch/brake combination - Central oil lubrication - Precisely guided press ram with oil-lubricated guides - UNIDOR press control - Swiveling control panel - Press and feed control cabinets, together on one platform, adjacent Nwodpedzqlvsfx Ah Heb Platform dimensions 3400 x 2250 mm, height without feet 2950 mm Width of the press without feed 2100 mm Depth of the press with drive motor 2300 mm Overall height of the press 4150 mm Weight of punching press approx. 18 tons. For transportation, the drive motor is removed and the machine is placed on its face. In addition: NC roll feed straightening machine ALBA type GGVHY400 Apparatus no. 1405 and 1406, order no. 910708 (year of manufacture 1992) - ALBA PSS 300 feed control - Feed length infinitely programmable from 0.1 to 6500 mm per stroke - Belt thickness at 400 mm width max. 3 mm - Belt thickness for 300 mm width max. 4 mm - Belt cross-section max. 1200 mm2 - Roller drive hydraulically controlled by the feed - Height-adjustable feed unit on the press to adjust the material infeed height - Hydraulic unit opposite - Drag straightener with hydraulic opening and closing Weight of the complete system approx. 24 tons Space required for transport a mega trailer with an internal height of 3 meters and a loading length of 13.6 meters good condition

Condition: new, Year of construction: 2025, Band width: max. 38 mm Feed length: max. 50 mm Band thickness: 0.05...1.02 mm Nwjdpfxs Ea U Ho Ah Hob Stroke rate: max. 260 rpm at full feed length Feed force: 90 N Optionally with mechanical control valve or optionally with electric valve (24V or 230V) Many other band widths and feed lengths available.

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: 25.12.15, Fresan FP 130P - C Frame Eccentric Press - 130 Tons (1300kN) TECHNICAL DATA: * Power: 130 tons (1300kN) * Strokes Per minute: 55 (variable) * Ram-Table Distance: 500 mm * Stroke Adjustment: 0 - 132 mm * Ram Adjustment: 95 mm (motorized) * Table Dimensions: 700 x 1000 mm STANDARD SPECIFICATIONS: * Conformity to CE safety regulations * Welded steel frame * Crankshaft made of AISI 4140 (42CrMo4) alloy steel. Highly durable and ductile. CNC ground for minimum surface friction. * SnBz-12 quality bronze bearings Nwjdpfjnyh Sijx Ah Hjb * Pneumatic clutch-brake combination * Fully closed gearbox with helical gears working in oil * Double body press safety valve * Safety PLC & light curtains & safety switches (Pilz) * Ram with 6 slides & waste oil collector * 7-inch HMI touchscreen operator panel * Speed control with AC inverter * Motorized ram adjustment * Mechanical fuse for overload protection (Hydraulic fuse can be installed on standard a machine after purchase) * Pneumatic counterbalance cylinders (ISO, 4 pcs) * Automatic central lubrication & used oil collectors (Thin oil / slideways oil) OPTIONAL EQUIPMENT: * Additional work table * Part ejector mechanisms(upper and/or lower ejectors) * Material feeding, loading & unloading systems (Decoilers, straighteners, pneumatic & servo feeders...) * Special design / customized machine