Workshop press

AYEL-TECH WP-HD 100

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Djdekvnumepfx Aiwjkl Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1984, condition: used, machine/vehicle number: 25 948, throat: 485 bzw. 1050 mm roller-Ø: 500 mm passage height: 380 mm table size: Arbeitstisch 780 x 800 mm sawing band length: ueber 2 Laufraeder 3920 - 4050 mm sawing band width max.: 20 mm band speed: 15 - 940 m/min engine: 380 V, 4 kW space needed: 950 x 2130 x 2100 mm Dsdpfx Aeb N Eh Hjiwokl weight: 1740 kg

Condition: good (used), Year of construction: 1975, working width: 3,100 mm, sheet thickness steel (max.): 10 mm, sheet thickness stainless steel (max.): 6 mm, back gauge: 700 mm, overall weight: 6,000 kg, total length: 3,400 mm, total width: 2,200 mm, total height: 1,800 mm, cutting length (max.): 3,100 mm, throat depth: 300 mm, Cutting length 3100 mm, cutting capacity 10 mm, motor 15 KW, working high 800 mm, back gauge 700 mm motorised, footpedal, 3 frontarms, fingerstop, pneumatic back support, cutting angle adjustable, dimension 3400x2200x1800 mm, weight ca. 6000 kgs Djdpfsvvwdyjx Aiwskl

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function Dsdpfx Aioh Hm Thswokl -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank Dkjdpog U Utvsfx Aiwjl via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: as good as new (ex-display), 3000 kg welding rotary table, hydraulically height adjustable Speed 0.05-0.6 U/min Table diameter 1200 mm Inclination 0-120° Total height 700 mm Dkjdpfx Aedvn E Ueiwjl Height adjustment with vertical pane until the mid- 960 mm ~ 1910mm Horizontal disc mass 1200mm up to 1900mm

Condition: new, capacity 90 degrees: round 240 mm capacity 90 degrees: square 240 mm 165 x 310 mm saw band length 2725 x 27 x 0,9 mm mm table height 890 mm band speed 35 / 70 m/min total power requirement 1,1 kW weight of the machine ca. 0,35 t Dimensions (LxWxH) 1,7 x 0,75 x 1,8 m Dkedpfx Aiohpktvewel The Z252/DG has the following equipment: - hydraulic cylinder, - emulsion pump, - eccentric clamp, - base, - saw blade, - 400V plug -16A- The machine is delivered fully assembled and ready for immediate use.

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm Dedpfohlnzkox Aiwekl column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: good (used), Year of construction: 2008, - Max. turning diameter over bed: 700 mm - Turning length: 1,500 mm Main spindle: - Speed range: 2,800 rpm - Enlarged main spindle: Ø 150 mm, bore: 110 mm - Drive power: 30 kW, 900 Nm - Spindle nose: Size 11 Total power requirement: 59.5 kVA Approx. machine weight: 14.5 t Space requirement approx.: 6.4 x 3.0 x 2.6 m EQUIPMENT: - 3-jaw chuck, SMW KNCS-N 400 K11 - Tailstock - Programmable CNC steady rest slide (cross slide NOT retractable) - SMW-AUTOBLOK SLU-3, self-centering steady rest, clamping range Ø 12 - 152 mm - Full clamping cylinder for partial hollow clamping, draw tube bore max. Ø 100 mm - In-process measuring system Renishaw for X-/Z-/C-axis - Programmable CNC tailstock on W-axis - Drilling/milling spindle and C-axis 0.001° - Tool changer: 80 positions Tool system: HSK-A63 - Y-axis travel +115/-115 = 230 mm - B-axis 225°, positioning in 0.001° increments - ICS / internal coolant supply for driven tools Dksdjxmirgjpfx Aiwol - Synchronized thread cutting with driven tools - Software for use of multifunctional tools, e.g. special tool with radially arranged indexable inserts, which can be positioned in the drilling/milling spindle at 60°, 90°, 120° and 180° positions - Software for gear hobbing for straight and helical gearing with speed synchronization of main and milling spindles - Electrostatic extraction unit - Chip conveyor - Documentation - CE marking

Condition: used, Year of construction: 2007, pressure 100 t stroke 500 mm table surface area 900 x 600 mm Dkodpovprv Rjfx Aiwol rapid traverse 22 mm/s stroke speed 2 mm/s ram surface 700 x 350 mm total power requirement 2,2 kW weight of the machine ca. 1,6 t dimensions of the machine ca. 1,9 x 0,85 x 2,3 m The machine is of the Italian make SICMI, which was traded by the Knuth company.