Year of construction: 2010, Condition: good (used), Very good solution to use one press for two different materials and You don't have any problems to sort them later. Felsgzulusq Rkg Ujpg Capacity 20 m3. 5,5 kW 400/32 A

Year of construction: 2024, operating hours: 250 h, Condition: as good as new (ex-display), Functionality: fully functional, Model: Lepton 5100 Demonstration machine Year of construction: 2024 Operating hours: approx. 250 hours Location: D 84069 Schierling Availability: short term Equipment: -Basic machine Lepton 5100 with screening deck 1 and 2 pre-screen deck with long hopper and dosing roller variably adjustable -Volume measurement via the load -Wind sifter screen deck 2 with nozzle, suction turbine and hose -Preparation for SD 1 wind sifter -Compressor -Water spray system -Remote control for all important settings via radio Diesel-electric drive Tir 4 Final -Plug-in option for connection to external power source (renewable energies) -Level compensation axles -Double axle 80 km/h approval -19,000 kg total weight -Transport dimensions: 11.97m overall length, 3.98m height, 2.53m width, no special permit required Other: Good used condition, fully operational Fpolq Rjvkfbpekg Uog

Year of construction: 2024, Condition: new, *Only the neodymium overbelt magnet is offered, not the conveyor belt underneath. *Neodymium magnets are among the strongest magnets in the world. They have an extreme pulling power and cannot be compared to ferrite magnets. Fpelq Rksdubpusg Usg Extremely high degree of separation, depending on the bulk height and the starting material. Probably the most compact overband magnet on the market. The competition often uses the less powerful ferrite magnets to save costs. dimensions approx. Length: 104cm Width: 22cm Height: 28 cm (at the motor) *Without controller Surcharge for simple manual start/stop control + 495 € A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600x68x36.5 mm * So nails are attracted to a length of 600 mm and thrown off to the side, in the area that is no longer magnetic. This overbelt magnet should be mounted approx. 5 - 9 cm above the material flow. *Assembly/suspension on site Ideal for separating nails from wood chips. Optionally also in a single-shaft shredder that is sucked off Requirements: *Your belt width or useful width inside (of the existing conveyor belt) should ideally be narrower than 55 cm *Suitable for separating nails from material flows that are less than 12 mm high and with a chip length of less than 25 mm. ----- Optional at extra charge: Cross and ascending belt demonstrators from € 7,995 net

Condition: like new (used), Year of construction: 2019, Functionality: fully functional, Amis ZBP 50 S Duo sawdust briquetting machine Year of production 2019 Load capacity up to 140 kg depending on material Felq Rkeumwm Sjg Ujpg 3.800 working hours Briquettes Ø 50 mm Tank with a capacity of 1.2 m³ Roller with feeder Pre-ironing Screw conveyor Hydraulic pump motors, 7.5 kW each Fan cooling Sawdust level sensor in the tank Hydraulic oil tank 100 l SIEMENS control system Dimensions length x width x height 3000 x 2400 x 1700 mm Weight 2000 kg The price of the new machine is 39.800 Euro

Condition: used, Year of construction: 2018, operating hours: 3,500 h, Functionality: fully functional, type of motor: three-phase motor, Guidetti WirePro 3000 Cable Granulation Line for Sale The Guidetti WirePro 3000 was our first major capital investment and has served us exceptionally well over the years. Line Components: Electrical cabinet PMG1200 Hydraulic Pre-Shredder Overband magnet Belt-driven Rasper 2 x Zig-Zag separators (for heavies removal) Belt-driven Granulator ROBI Density Separation Table - located on a c.1.6m stand to allow gravity feed into bags or conveyors - Stand also available if needed. F15 Dust Separation Table Petini Franco 12000 m³ Dust Extraction System Condition: The plant is in good working order and has been meticulously maintained with daily servicing and repairs. While some minor work may be required, it remains fully operational and ready for production. Included Spares: Spare shaft for primary granulator Spare cutters, blades, dead-blades, and cutting teeth (consumables) Performance: When processing cable, the machine achieves throughput rates of 800–1,100 kg/hour, depending on the type and condition of the material. Why Choose This Machine? This WirePro 3000 has been our primary workhorse for over five years, delivering reliable performance and consistent results. With proper maintenance, it has the potential to remain a profitable asset for many years to come. Felqevi Nlco Rkg Ujpg For anyone looking to granulate cable efficiently and effectively, this is an excellent investment.

Condition: used, Front crusher+ conveyor + Grinding mill front crusher 2 axle brand Hatlapa 11 kW B 400 V, grinding mill unknown. RAU conveyor, blower also present including control cabinet and wiring. Fpelqevi I T Ej Rkg Ujg This installation has recently run in plastic still works, can not be tested. Respond with name , Company name and phone number.

Condition: like new (used), Year of construction: 2024, Functionality: fully functional, pressing force: 30 t, Used Bramidan B30 baler. Newly repainted. Ready for use, fully equipped, in perfect working condition. New oil. Felqeviymwj Rkg Uepg

Year of construction: 2022, operating hours: 400 h, Condition: as good as new (ex-display), Functionality: fully functional, !!!Demonstration machine with low operating hours!!! Model: Lepton 5100 Year of construction: 2022 Operating hours: approx. 400 hours Location: D 84069 Schierling Availability: short term Equipment: -basic machine Lepton 5100 with screen deck 1 and 2 Pitch screen deck 1: 36mm Pitch screen deck 2: 24mm pre-screen deck with long hopper and dosing roller variably adjustable -Volume measurement via the load -Preparation of air separator -Compressor -LED package -Remote control for all important settings via radio Diesel-electric drive 80kW -Level compensation axles -Double axle 80 km/h approval Fpolq Rkgort Uvzj Usg -19,000kg total weight -Transport dimensions: 11.97m overall length, 3.98m height, 2.53m width, no special permit required Other: Very good used condition, fully operational

Year of construction: 2024, Condition: new, Overband magnet Length: 2500 mm Height: około 400 mm Width: 1000 mm Belt width: 750 mm Magnet width: 500 mm Magnet length: 1044 mm Folqoh U R Tgs Rkg Ujpg Power: 1,5 kW(hydraulic or electric) Magnet field: 400 Gauss(may catch 100 mm pieces from maximum distance 300 mm Overband new, 12 months warrenty,

Condition: used, Revolving briquetting press RUF type RBK 55/2500/120 S Fslq Rehg Uz Iskg Ujpg Hydraulic pellet press or briquetting press for grinding sludge, metal chips, or similar No. 70002 Year of construction 2009 Briquette diameter 120 mm Briquette length in the pre-compactor approx. 120 mm Pressing force in the pre-compactor 30 tons at 260 bar Briquette length in the main compactor approx. 80 mm Pressing force of the main press cylinder 250 tons at 260 bar Stroke size of the main press cylinder 120 mm Pressing force of the counter-press cylinder 250 tons at 260 bar Stroke size of the counterpress cylinder 15 mm Piston diameter of the main press cylinder 350 mm Press stroke Cycle time approx. 30 sec. for grinding sludge with low residual oil content Hopper size of the screw conveyor 1000 x 600 mm Hydraulic motor power 37 kW Mains connection 400 Volt, 50 Hz, 45 kW - Revolver with 5 stations for high material throughput - Pre-compressor stage for pressing material into the turret disk - 2 opposing main press cylinders with 120 mm and 15 mm stroke - Ejection cylinder for ejecting the finished briquettes from the turret disk - Infinitely variable adjustment of the hydraulic speed for each pressing stage - was used for grinding sludge from metal processing - Material hopper as hopper with screw conveyor - the machine was completely overhauled at RUF in 2018 - a new SIEMENS Simatic touch panel was installed in 2020 - only a few operating hours after the overhaul very good condition Grinding sludge recycling - great savings through cooling lubricant recovery - Large savings in disposal costs due to the reduction in volume and weight of the grinding sludge - Grinding sludge briquettes with a low residual oil content can possibly be classified as "non-hazardous waste".

Year of construction: 2014, operating hours: 4,000 h, Condition: excellent (used), machine/vehicle number: 1009, COMPOST TURNER Fjlq Rkgslu E Hxj Uspg

Condition: new, Year of construction: 2025, Functionality: fully functional, Are you looking for an ironclad supply or discharge conveyor we will build them for you in any size or shape. Fjlq Rket Iwgnog Ujpg We are also an excellent partner for your drain screws. Conveyor belts, supply belts in almost any size, with closed sides, carriers etc. etc. entirely according to your wishes and requirements.

Condition: excellent (used), Year of construction: 2011, Functionality: fully functional, Used Orwak 3115 baler. Perfectly working, ready to use, fully equipped (bale trolley, strap rolls). New press plate, cylinder seals, pressure sensor, new oil. Fpjljviyi Eoq Rkg Uog

Condition: defective spare-parts repository (used), Year of construction: 2013, Manufacturer: HSM Tip: HL 4010 Li Year of construction: 2013 The equipment is incomplete and is sold as a part Fault: Hydraulic pump missing Fpslq Rkjur Raveg Usg Control is missing Power supply unit missing

Year of construction: 2023, Condition: new, Set of jaws for Metso LT120, QUARRY TOOTH Fixed jaw MM0521203 18%Mn2%Cr - 2120 kg Swing jaw MM0521201 18%Mn2%Cr - 1875 kg Fpelq Repit Rbskg Usg Very good quality castings ALL CASTING CHECKED WITH SPECTROMETER, TO PROOF BEST QUALITY Price for set EXW Poland, worldwide shipping can be arrange

Year of construction: 2017, operating hours: 35 h, Condition: as good as new (ex-display), machine/vehicle number: 1242, COMPOST TURNER Fpslq Rkolu E Eajg Usg

Condition: new, Year of construction: 2024, Functionality: fully functional, Drain screw system in any length, diameter, etc, tailored to your needs and requirements of course also available separately. Fpjlq Rkst Iwt Uog Usg reactions or questions ? please with full name, company name and phone number.

Condition: defective spare-parts repository (used), Year of construction: 2016, Manufacturer: HSM Fpslq Rkgsur N Uxe Ueg Tip: HL 4809 Re The device is incomplete, for sale in the condition shown, defect: Check: incomplete Power supply unit is missing The hydraulics of the main motor are missing For sale as a spare part

Year of construction: 2022, Condition: new, Set of blow bars martensitic with double layer of ceramic for Metso 1213 crusher. We can also offer high chrome with ceramic for this machine All casting from EU foundries, best quality on the market Fpolqjihfc Se Rkg Ueg We can also offer blow bars for all other machines like Tesab, Pegson, Rubblemaster, Hartl and many more

Condition: new, Year of construction: 2025, Functionality: fully functional, We deliver machines at any place, install when you whish and support you along the way, at any time. Fpslqjg Ainqe Rkg Ueg Grinder 1000 series 45kW 3 x 2 knife set 2 x stators screen deck your request Product discharge and storage in various options. Motor power adjustable. Other adjustments negotiable. Delivery in consultation. Call or email us for consultation or if you have any questions

Year of construction: 2022, Condition: new, Set of cones(concave + mantle) Maxtrak 1000 Medium Coarse - very good quality. 22%Mn, with SPECTROMETER CERTIFICATE, highest quality on market! Parts number: 603/9052-22 MC + 603/9106 Fpolq Reigvfvjkg Ujg

Condition: new, Year of construction: 2025, Functionality: fully functional, We deliver the machines where you want them, install them if you wish by mutual agreement. Optional: stainless steel drain element, stainless steel storage silo, blower, pipes approx 3 meters. Grinder 800 series 22 kW or 37 kW 3 x 2 blade set configuration. Bwj3E79Mpn 2 x stators screen deck your request With Variablele Frequency controller, Optional Product discharge and storage in various options in combination extra favorably priced Motor power adaptable. Other adjustments can be discussed such as a rotor adjustment, more blades e.g. 5 rows of blades or heavy duty version. Delivery / time in consultation. Fpelq Rkgst Iw Hue Usg Call or email us for consultation or if you have questions, please respond with your name, company name, and correct phone number. Without these correct details RSS Recycling Shredders and Solutions (Netherlands) cannot respond.

Year of construction: 2022, Condition: new, Set of jaws for Extec C10 - Heavy Duty version with big tooth(50 mm tooth high) J692HDE, J693HDE Fixed jaw 18%Mn2%Cr - 870 kg Swing jaw 18%Mn2%Cr - 610 kg Very good quality castings Folq Rkgeigvc To Uopg Price for set EXW Poland, worldwide shipping can be arrange

Condition: new, Functionality: fully functional, Year of construction: 2023, operating hours: 4 h, power: 45 kW (61.18 HP), Rotor lenght 1000 mm, knives 40 x 40 mm, 2 stator knives, kW 45+ 2.2, Weight approx 5000 kG, Hoppersize 1400 x 1000 mm, screensize on your request. PLC, automatic reverse as well by manual, connections for convayors, and included motor cover, etc, etc Optional Conveyor beld available This machine is plug and play and have Dutch CE certificat Conveyor or other infeed or discharge methods can be discussed. Any other wish you have, do not hessitate to ask. Fjlq Rkgskzg U De Uopg For more info: RSS Recycling Shredders & Solutions Contacts or questions with companyname, telephone number and your name. Without these we are not able to reply your request

Year of construction: 2022, Condition: new, Fits to following machines: Powerscreen Warrior 1400, Warrior 1800, Chieftain 2100 Gear triple pump X1A504650335033/124003/1C we are polish distribiutor of David Brwon Hydreco Fjlq Rkgjigvcte Uspg original genuine new pumps. All Powerscreen pumps on stock. Pump designed for Powerscreen Warrior 1400, Warrior 1800, Chieftain 2100