Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Dsdjvf E Avjpfx Aiwjut Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 22,000 kg, oil tank capacity: 900 l, For sale is a complete baling system consisting of conveyor technology, baling press (partially refurbished and tested) and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Duodpfxsviwdme Aiwjt Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Dsdpfxjx A U Ncs Aiweut Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 60 t, bale weight: 550 kg, Equipment: documentation/manual, Used HSM V-Press 1160 Plus vertical press from 2015. The device is regularly serviced by an authorized service center. The press is fully functional and in very good technical and technical condition. Dodpfey Iyu Dex Aiwout Crushing force: 594 kN Voltage / required: 400 V / 50 Hz Width x height of the loading opening: 1195 x 650 mm Bale length x width x height: 1200 x 1100 x 1200 mm Width x height x height of the machine: 1780 x 1568 x 2985 mm Machine weight: 2403 kg Pressed material: foil, mixed paper, cardboard, cutting machine waste Freight costs depend on the weight, volume and above all on the distance, the following information is relevant for inquiries: Delivery address (postcode and name of the town), but further details require a telephone call, so we ask you to inquire about transport costs and other delivery modalities to contact us by phone. Our contact details can be found under the legal information of the seller. We sell and export worldwide, due to our very large storage capacity we can also deliver larger quantities flexibly and quickly. We issue intra-community invoices - excluding VAT. Opening hours Mon-Fri: 8 a.m.-4 p.m. sat .: closed

Condition: excellent (used), Year of construction: 2016, pressing force: 80 t, DIXI 80 SLD horizontal press Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Dodpfey Iykxjx Aiwsut Pressure force : 80 t Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Machine weight approx. 8,000 kg (without bale)

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, pressing force: 40 t, bale weight: 370 kg, HSM HL 4010 Re / Li horizontal baler. Equipped with a loading tipper for the basket. Manufactured in 2015. Very good condition - regularly serviced by an authorized service center. Ready for use. Djdpey Iyd Sefx Aiweut Available for binding with wire, string, or polypropylene tape. Semi-automatic baler system with a 40-ton pressure for economical volume reduction of residual (recyclable) materials in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulation mats and other compressible materials. Press force: 400 kN Transport width: 1,767 m Transport height: 2,489 m Transport length: 5,573 m Weight: 4,500 kg Drive power: 7.5 kW Bale weight (depending on material): 300-350 kg Bale length x width x height: 750 x 1200 x 750

Condition: ready for operation (used), Year of construction: 2009, bale weight: 550 kg, total width: 1,570 mm, total height: 2,985 mm, overall weight: 2,403 kg, total length: 1,800 mm, filling opening width: 1,195 mm, filling opening length: 65 mm, bale width: 110 mm, bale length: 120 mm, bale height: 120 mm, transport height: 225 mm, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2009 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Dujdpfxsy Iwi Es Aiwst Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Filling opening: 119.5 x 65 cm Condition: very good! Video of machine in operation available on request.

Condition: ready for operation (used), Year of construction: 2008, filling opening width: 1,195 mm, filling opening length: 65 mm, bale length: 120 mm, bale width: 110 mm, bale height: 120 mm, bale weight: 550 kg, total width: 1,570 mm, total height: 2,985 mm, total length: 1,800 mm, overall weight: 2,403 kg, Brand: HSM Model: V-Press 1160 plus Year of manufacture: 2008 Pressing force: 532 kN Voltage: 400 V Max. bale weight: up to 550 kg (depending on material) Bale dimensions: 120 x 110 x 120 cm Machine weight: 2,403 kg Machine dimensions: 180 x 157 x 298.5 cm Djdpfx Aey Iwcxoiwjut Filling opening: 119.5 cm × 65 cm Condition: very good! Video of the machine in operation available upon request.

Condition: ready for operation (used), Year of construction: 1996, functionality: fully functional, pressing force: 2 t, bale length: 1,200 mm, bale width: 500 mm, bale height: 400 mm, bale weight: 100 kg, overall weight: 1,820 kg, This is a fully automatic baling machine that ties the bales with two steel wires (2.2 mm in diameter). A fan blows the waste paper into the machine through special tubes with a diameter of 100 mm. The fan and approximately 10-meter-long tube are included in the price. The machine is in working condition and can be tested. For sale due to lack of use; ideal for baling waste paper from printing and hygiene products. Dujdpsy Ic Rusfx Aiwjt

Condition: ready for operation (used), Year of construction: 2013, operating hours: 5,000 h, functionality: fully functional, machine/vehicle number: 01113, total width: 2,180 mm, total length: 12,200 mm, bale length: 500 mm, bale height: 400 mm, pressing force: 350 t, overall weight: 34,000 kg, Ecotecnica shear baler mod. 2535, year 2013, with approximately 5,000 operating hours, in good working condition and complete with documentation. Machine suitable for compressing and shearing ferrous scrap, including sections, sheet metal, and mixed scrap. Technical data: Shear force: 350 tons Operating hours: 5,000 Compression box length: 5.0 m Dodsy Ibw Tjpfx Aiwout Box width with wings open: 1.70 m Bale size: 500 x 400 mm Total length: 12.20 m Width: 2.18 m Weight: 34,000 kg Equipment: Iveco diesel engine, 172 HP Radio remote control Complete documentation Machine is fully functional and ready to use. Inspection and testing possible.

Condition: ready for operation (used), Year of construction: 2015, functionality: fully functional, machine/vehicle number: MM1007, bale length: 880 mm, bale height: 600 mm, pressing force: 500 t, Taurus shear baler model E 556.P, year 2015, in excellent working condition and complete with documentation. This machine is ideal for baling and shearing all types of ferrous scrap: profiles, sheet metal, bulky mixed scrap, and vehicles. Technical data Shearing force: 500 tons Shearing width: approx. 950 mm Shearing height: approx. 640 mm Box length: 5,600 mm Open box width: 2,400 mm Dedpjy Iblwsfx Aiwjut Bale size (closed): Width: 880 mm Height: 600 mm Features Soundproofed 125 HP diesel engine Operator cabin Radio remote control Complete documentation Machine ready for operation.

Condition: ready for operation (used), HSM V-Press 860 baler, year 2008–2009, price: €5,800 Pressing force: 54 kN Specific pressing force: 63.46 N/cm² Drive power: 7.5 kW Cycle time: 25 s Loading height: 1,110 mm Feed opening width x height: 1,195 x 650 mm Bale dimensions (L x W x H): 1,200 x 780 x 1,200 mm Bale weight: 480 kg Dodpjra Rbgsfx Aiwsut Machine dimensions (W x D x H): 1,797 x 1,247 x 2,985 mm Machine weight: 2,008 kg Binding material: wire Materials processed: foil, mixed paper, cardboard, die-cut waste, textiles, Big Bags, polystyrene HSM V-Press 860 plus, year 2013–2015, price: €8,000 HSM V-Press 860 L, year 2015, price: €9,000 HSM V-Press 860 plus, year 2019, price: €9,000 HSM V-Press 860 plus, year 2024, price: €10,000 HSM V-Press 860, new/ex-demo, year 2020, price: €13,000 4-fold bale wire tying Bale dimensions (L x W x H, mm): 1,200 x 800 x 1,000–1,200 Bale weight: approx. 500 kg Technical data (L x W x H, mm): 1,213 x 1,824 x 2,987 Feed opening (mm): 1,200 x 565 Cycle (s): 35 Pressing force (t): 54 Power supply (V): 400 (three-phase) HSM V-Press 860 plus B, year 2020, price: €14,000 Pressing force: 594 kN Voltage/Frequency: 400 V/50 Hz Drive power: 4 kW Feed opening width x height: 1,500 x 651 mm Bale dimensions (L x W x H): 1,500 x 780 x 1,200 mm Bale weight: 550 kg Feeding type: Manual Machine dimensions (W x D x H): 2,099 x 1,245 x 2,985 mm Machine weight: 2,336 kg Binding material: wire Material processed: foil, cardboard Idle cycle time: 25 s

Condition: good (used), Strautmann AutoLoadBaler baler Baler for compacting: Cardboard Foil PET bottles Foam Cans Electronic waste Machine dimensions (L / W / H) mm: 2047 / 2179 / 2950 Filling opening approx. 1192 mm / 575 mm Bale dimensions (L / W / H) mm: 1200 / 800 / 1100 Bale weight approx. 480 kg Dodpfxov Aktno Aiweut Pressing force: 530 kN Year of manufacture: 2017-2018

Condition: good (used), Brand: BRAMIDAN Model: B3 Width (cm): 94 Depth (cm): 72 Height (cm): 198 Weight (kg): 310 Power (kW): 1.1 Voltage (V): 230 Chamber width (cm): 70 Chamber depth (cm): 50 Chamber height (cm): 110 Year of manufacture: 2010-2015 Pressing force (t): 3 Duedov Akr Rjpfx Aiwst Noise level (dB): 69 Price: 2,000 EUR B5 - Ideal for large cartons: High performance – high throughput The bale is ejected automatically Strap rollers positioned at the front for easy strap replacement Cardboard bale weight (kg): 80-110 Plastic foil bale weight (kg): 90-130 Bale size W x D x H (mm): 1000 x 700 x 800 Pressing force (t): 5 Power supply: 1x230V 50Hz 10A Motor (kW): 1.1 Noise level (dB): 65-68 Average cycle time (sec): 33 Dimensions W x D x H (mm): 1360 x 895 x 2370 Weight (kg): 600 Filling opening width x height (mm): 1000 x 500 Year of manufacture: 2014-16 Price: 3,800 EUR

Condition: ready for operation (used), Model: HSM V-press 1160 plus baler Pressing force (kN): 532 Bale weight depending on material: up to 550 kg Max. bale size (mm): 1200x1100x1000-1200 Dujdpfora Nyuex Aiwst Dimensions L x W x H (mm): 1780x1150x2985 Power (kW): 7.5 Weight (kg): 2300 Year 2007-2010, price: 5800 EUR Year 2011-2013, price: 6000 EUR YEAR 2018 COSTS 6000 EUR We also have HSM V-press 1160 max balers from 2014-2015 available.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, Equipment: documentation/manual, The HSM HL 3521 S model, with its very large loading aperture, is an optimal device for compacting large quantities of paper, cardboard, film, and other packaging materials with particularly large and bulky dimensions. The HSM HL 3521 S model is also a specialist in baling highly expandable materials such as foam. The press was purchased brand new. Regularly serviced. Price of a brand-new machine: approx. €90,000 Year of manufacture: 2023 Pressing force: 320 kN Max. bale weight: 600 kg Machine dimensions (W x D x H): 7900 x 1660 x 2485 mm Loading aperture (W x H): 800 x 2100 mm Several units of the HL 3521 S model available from years: 2011 / 2015 / 2017 / 2023 Djdpfx Aoy H Dazoiweut

Condition: good (used), Year of construction: 2013, functionality: fully functional, Available from 15.05.2026 Baling Press Paal Konti 325 G, Year of manufacture 2013 Technical Data: Dujdpey A Ibnjfx Aiwet Manufacturer: Paal Model: Konti 325 G Year of manufacture: 2013 Operating hours: 11,723 (as of 10.02.26) Pressing force: 100 t Drive power: 2 x 55 kW Feed opening: 1020 x 1750 mm Bale dimensions: 750 x 1100 mm, length variable Tying: 5-fold automatic Throughput rate at: 35 kg/m³ approx. 13.5 t/h 60 kg/m³ approx. 21.5 t/h 100 kg/m³ approx. 33 t/h Bale weight up to 800 kg Transport dimensions approx. 12,216 x 2,530 x 2,800 mm (LxWxH) Machine weight approx. 28,000 kg Materials: Paper, cardboard, light waste, plastic waste Please note: All technical data is based on the manufacturer's information. We do not assume liability for the details provided or for any potential errors. This offer is non-binding, subject to prior sale, and can be withdrawn at any time. Inspections are possible by arrangement. Sale against prepayment ex works, without warranty or guarantee.

Condition: good (used), Year of construction: 2019, functionality: fully functional, Baler Dixi 80 SLD, with lifting/tipping device, semi-automatic, year of manufacture 2019 Manufacturer: Dixi Model: Dixi 80 SLD Year of manufacture: 2019 Drive power: 11 kW, 400 V / 32 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500–600 kg Binding: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film The press is in good condition. It has been checked and tested by us. A video is available on our website or YouTube channel. Please note: All technical data are based on manufacturer information. We do not accept any liability for the stated data or possible errors. This offer is subject to change without notice, prior sale, and revocation at any time. Inspection is possible by appointment. The sale is ex works, against advance payment, without warranty or guarantee. Dsdpfx Aoy Avlnsiweut

Condition: good (used), Year of construction: 2019, functionality: fully functional, Baler Dixi 80 SLD, with lifting/tipping device, semi-automatic, year of manufacture 2019 Manufacturer: Dixi Model: Dixi 80 SLD Year of manufacture: 2019 Drive power: 11 kW, 400 V / 32 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500–600 kg Binding: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film Duodpoy Avhcofx Aiwet The press is in good condition. It has been checked and tested by us. A video is available on our website or YouTube channel. Please note: All technical data are based on manufacturer information. We do not accept any liability for the stated data or possible errors. This offer is subject to change without notice, prior sale, and revocation at any time. Inspection is possible by appointment. The sale is ex works, against advance payment, without warranty or guarantee.

Condition: reconditioned (used), bale length: 1,200 mm, bale width: 700 mm, bale height: 800 mm, bale weight: 380 kg, Press in perfect condition, unused after overhaul. Serviced only by the manufacturer. Perfect condition. Fully automatic operation. Adjustable bale length: 600-1200mm. 15 kW motor. Year: 2007. Bale weight approx. 380 kg. Dusdpfox S Sbdjx Aiwet

Condition: ready for operation (used), Baler Hsm 155 VL Bale dimensions L x W x H: 1100 x 700 x 700 - 950 mm Bale weight: 2000 - 250 kg (Cardboard) Technical data: L x W x H: 1470 x 940 x 2259 / 2439 mm Weight: 950 kg Pressure force 16 tons Power supply: 400 V (three phases) Dsdpfx Aora Nrmoiweut Motor power: 4 kW Bale ejector Hsm 155.1 VL baler pressure force 18 tons Price of Hsm 155.1 VL baler - 2600eur Hsm 155.2 vl baler pressure force 16 tons Price of hsm 155.2 vl baler - 2800eur

Condition: new, The briquette press is designed for compressing all types of sawdust and wood shavings into briquettes. The briquetting press features a compact, user-friendly design and is manufactured in Germany. The large oil tank enables continuous operation. The briquette press is ready for immediate use – simply plug it in and start working. Dodpfx Ajyr Tpnoiwsut

Condition: new, For industrial production of rectangular briquettes The ZBP 500 compacts pressable materials into high-density briquettes. The briquettes are easy to store and, thanks to their stackability, can be transported efficiently. In the press chamber of the hydraulic press unit, the briquettes are shaped by a pressure cylinder. This allows up to nine briquettes per minute to be produced with a pressing force of 1 kg/cm². Standard equipment:  Safety limit switches for oil temperature and oil level  Oil cooler  Automatic briquette length monitoring  Automatic hopper fill level monitoring  Control cabinet with PLC control for fully automatic operation Options:  Custom hopper extension available to meet customer requirements  Press stamp with inscription / logo Dodjyr I Hzspfx Aiwjut

Condition: new, machine/vehicle number: AMIS Brikettierpressen Typ ZBP 50, 60 und 70, AT A GLANCE: Variable container dimensions (customizable to customer requirements) Left- or right-hand configuration Hydraulics with separate oil tank Dedjyr I Huspfx Aiwout All model series also available as “DUO” variants Wood chips, sawdust, wood shavings, etc. are generated in all woodworking and industrial processing businesses. Every day, storage and transport costs for these materials are significant. Briquetting presses offer the ideal solution, as briquettes are easy and space-saving to store and transport. Additionally, the risk of spontaneous combustion is significantly reduced. Briquetting presses require little space, are robustly constructed, and equipped with low-maintenance technology. Whether wood, paper, biomass, foam, or polystyrene – the ZBP series briquettes any suitable material. With a throughput capacity of up to 35 – 130 kg/h, they are particularly suitable for small and medium-sized enterprises. Flexible installation options thanks to the availability of left- and right-hand designs. So start briquetting today!

Condition: new, machine/vehicle number: ZBP 30, The AMIS briquetting press type ZBP 30 produces 30 mm briquettes. These briquettes are ideal for combustion in wood gasifiers and smaller wood chip boilers or heating systems. Any material from a woodworking operation (shavings, dust, etc.) can be briquetted. Wood chips, sawdust, wood shavings, etc., are generated in all craft and industrial woodworking companies. These materials incur significant storage and transport costs on a daily basis. Briquetting presses offer an ideal solution by compressing the material into briquettes, which are simple and space-saving to store and transport. Furthermore, the risk of spontaneous combustion is significantly reduced. The briquetting presses require little space, feature sturdy construction, and are equipped with low-maintenance technology. Whether it is wood, paper, biomass, foam, or polystyrene, the ZBP can briquette all suitable materials. With a throughput of up to 35 – 130 kg/h, they are especially suited for small and medium-sized enterprises. Dujdpfx Ajyr I Hnsiwot