Used bale presses for sale (180)

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, year of last overhaul: 2026, volume flow: 930 m³/h, Technical data baler: Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Ijdpfxey S Ru Ao Ag Isib Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2015, operating hours: 30,143 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 570 kg, overall weight: 20,000 kg, oil tank capacity: 600 l, year of last overhaul: 2026, volume flow: 800 m³/h, Technical data baler: Manufacturer Presona AB, Sweden Type LP 60 VH1 Year of construction 2015 Total operating hours, 30,143 hours, as of July 2025 Effective pump running time onl 6,527 hours, as of July 2025 Number of pressed bales 115,193 bales, as of July 2025 Press force pre press 25 t Main press force 60 tonnes Specific pressing force 73N/cm² Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Theoretical throughput capacity 800 m³/hour Throughput capacity under operating conditions 350 m³/hour Bale dimensions 1,100 x 750 mm Drive power 37 kW Tying 5-fold vertical, fully automatic Throughput capacity with a Bulk weight of 50 kg/cbm 11 to 14 tonnes/hour Bale weights 420 to 570 kg, depending on material Hydraulic oil tank volume 600 litres Baler dimensions assembled with hopper 10,100 x 3,750 x 4,310 mm (l x w x h) Transport dimensions excluding press 10,100 x 2,400 x 3,000 mm (l x w x h) Machine weight press approx. 20 tonnes Condition of the press: The press was partially overhauled in our workshop and then tested in manual and automatic mode. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Grease cartridges of the automatic roller lubrication system replaced Slide rails cut out from the press floor in the press room Underbody reinforced with welded sheets New HARDOX slide rails welded in Wire station with deflection rollers for the lower wire cleaned and made operational Slide rails cut out from the floor in the press channel New HARDOX slide rails welded in Both side walls of the press channel dismantled, derusted Worn side wall plates cut out Complete side walls covered with new wear plates and welded Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Machine checked, general maintenance work carried out and press tested in manual and automatic mode Comments: Iodpfx Aoy S Rtlog Isib The press is sold without a conveyor belt and without wire stations. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, empty load weight: 50,800 kg, year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Iiodpjy S Rruofx Ag Iob Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Iiedpfx Asy S Rqwsg Ieb Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Iiedpfxsvq Rtkj Ag Iob Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Year of construction: 2012, operating hours: 5,812 h, functionality: fully functional, Baler Presto HPK 50 HS, year of manufacture 2012, with perforator and incline conveyor (sliding belt conveyor) Manufacturer: Presto Model: HPK 50 HS Year of manufacture: 2012 Operating hours: 5,812 Drive power: 30 kW Press force: 50 t Feed opening: 1,600 x 650 mm (L x W) Chamber cross-section: 700 x 950 mm Max. filling volume: 1.06 m³ Cycle time: 19 s Tying: 4-fold Throughput rate at 35 kg/m³: 5.5 t/h Iiedpfxey R Tp Tj Ag Isb 60 kg/m³: 8.8 t/h 100 kg/m³: 12.7 t/h Bale weight: up to 500 kg Machine dimensions: 8,420 x 1,900 x 2,400 mm (L x W x H) Machine weight: approx. 10,500 kg Perforator, hydraulically movable Drive power: 2 x 4 kW / 400 V Throughput: approx. 220 m³/h Clear feed opening: 1,380 x 1,200 mm Incline conveyor Length: 7,931 mm Belt width: 1,400 mm Total width: 2,026 mm Incline: 29° Speed: 0.6 m/s Materials: Paper, cardboard, film, PET bottles Please note: All technical specifications are based on manufacturer information. We do not accept liability for the accuracy of these specifications or for potential errors. This offer is non-binding, subject to prior sale, and may be withdrawn at any time. Inspections by prior arrangement are possible. Sale is ex-works, subject to prepayment, with no warranty or guarantee.

Condition: good (used), Year of construction: 2021, operating hours: 123 h, functionality: fully functional, Vertical Baling Press HSM V-Press 860 plus, Year of Manufacture 2021 Technical Data: Manufacturer: HSM Model: V-Press 860 plus Year of manufacture: 2021 Operating hours: 123 Pressing force: 60 t Drive power: 4 kW Filling opening: 1195 x 645 mm Iodjy R Tncspfx Ag Isib Filling height: 1114 mm Bale size: approx. 1200 x 1200 x 780 mm Bale weight: 480 kg Tying: manual Theoretical idle cycle time: 25 s Theoretical press output: 12 cbm/h Dimensions: 1800 x 1253 x 2990 mm (W x D x H) Weight: 2213 kg Materials: Film, paper, cardboard Note: The press is in good condition. It has been inspected and tested by us. A video is available on our website or YouTube channel. Please note: All technical data is based on manufacturer information. We do not assume liability for any provided information or possible errors. Offers are subject to change, prior sale reserved, and may be revoked at any time. Inspections are possible by appointment. Sale is ex location, without warranty or guarantee. Our payment terms are 100% advance payment.

Condition: good (used), Year of construction: 2021, operating hours: 450 h, functionality: fully functional, Vertical Baler HSM V-Press 860 plus, Year of Manufacture: 2021 Technical Data: Manufacturer: HSM Model: V-Press 860 plus Year of Manufacture: 2021 Operating Hours: 450 Pressing Force: 60 t Drive Power: 4 kW Feed Opening: 1195 x 645 mm Filling Height: 1114 mm Bale Size: approx. 1200 x 1200 x 780 mm Bale Weight: 480 kg Binding: manual Theoretical Cycle Time (idle): 25 s Theoretical Throughput: 12 cbm/h Dimensions: 1800 x 1253 x 2990 mm (W x D x H) Weight: 2213 kg Ijdpfx Agjy R Srtj Isib Materials: Film, Paper, Cardboard Comment: The baler is in good condition. It has been checked and tested by us. A video is available on our website or YouTube channel. Please note: All technical data is based on the manufacturer's information. We accept no liability for the accuracy of the information provided or for any possible errors. Offers are subject to change without notice, prior sale reserved, and may be withdrawn at any time. Inspections are possible by appointment. Sale is ex location, without warranty or guarantee. Our payment condition is 100% advance payment.

Condition: used, We are selling a used waste baler press. Ijdey S Tf Dopfx Ag Ioib It is designed for use with paper, cardboard, and plastic film. The press is fully functional. A demonstration video is available.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,250 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, power: 22 kW (29.91 HP), year of last overhaul: 2025, volume flow: 530 m³/h, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the whirling unit replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Ijdjy R Npispfx Ag Ijib Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 13,209 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,250 mm, filling opening length: 1,050 mm, bale width: 100 mm, bale height: 700 mm, bale weight: 500 kg, overall weight: 8,500 kg, oil tank capacity: 400 l, power: 15 kW (20.39 HP), year of last overhaul: 2026, volume flow: 108 m³/h, Technical data baler: Manufacturer according to type plate BRAMIDAN (original manufacturer Presto GmbH & Co. KG) Type HC 50 (corresponds to the Presto HPK 50) Year of manufacture 2007 Operating hours 13,209 hours, as of March 2026 Number of bales pressed: 23,379 bales Pressing force 50 tonnes Specific pressing force 650 kN/m² Feed chute dimensions 1250 x 1050 mm (L x W) Filling volume 0.96 cm³ Theoretical cycle time 32 seconds Theoretical throughput capacity 108 m³/hour Bale dimensions 1100 x 700 mm (w x h) length variable Drive power 15 kW Power consumption, total in 50 A Tying 4-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm approx. 3.1 t/hour Bulk weight of 60 kg/cbm approx. 4.5 tonnes/hour Bulk weight of 100 kg/cbm approx. 7.2 tonnes/hour Bale weights with a bale length of approx. 1.2 m up to 500 kg, depending on material Hydraulic oil tank capacity 400 litres PLC control Siemens S7-200 Iodpfxey R Npcj Ag Ijib Effective transport dimensions excluding baler 6850 x 1950 x 2650 mm (l x w x h) Transport weight of press 8.5 tonnes Condition of the baler: The press was used in a production facility exclusively for pressing cardboard and was regularly serviced. With only 13,209 operating hours, the machine has seen little use. The press was partially overhauled in our workshop and then tested. The following overhaul work was carried out: Machine cleaned Bale retainer made operational and lubricated Light barrier replaced Twisting unit completely dismantled, broken down into individual parts, all bearings replaced, all plastic glides replaced, lubricated, chain tension adjusted Knife and counter knife dismantled, sharpened, reassembled Knife gap readjusted General maintenance work carried out and lubricated Scope of delivery: 1 baler with wire coil boxes, without wire (6850 x 1950 x 2650 mm) 1 bale chute (5100 x 1150 x 450 mm) 1 floor-mounted wire coil box (1450 x 380 x 360 mm) To transport the baler, you will need a tautliner with an effective internal height of 2700 mm. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Iijdpfxoy R Nnfs Ag Isb Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Colour: Grey Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE certificate present: No - Serial number: 307 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Iiedpfeym Uxtjx Ag Isb Yorick Diebels

Condition: used, Year of construction: 2005, total width: 1,300 mm, total height: 3,850 mm, total length: 2,200 mm, Colour: Grey Empty weight: 1.250 kg Price: On request - Year: 2005 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 308 - Transport dimensions: 2200mm x 1300mm x 3850mm (l x w x h) Iijdpjyrtcuefx Ag Ijb - Transport weight [kg]: 1250kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Bramidan 4-X25 – High-performance baler for waste compaction Suitable for various materials, including stretchable types Large, wide chamber Safety locks prevent material expansion inside the chamber Short cycle time allows fast waste processing TYPES OF WASTE: Cardboard Plastic film Paper PET bottles Aluminum cans Rigid plastics Textiles EPS Styrofoam Steel cans BALE DIMENSIONS Iisdpfxov Ak Dgs Ag Iob 1200 x 800 x 800 mm PRESSING FORCE 25 t BALE WEIGHT Cardboard (kg): 200-300 Plastic film (kg): 250-350 Price 4500 EUR

Condition: excellent (used), Year of construction: 2011, operating hours: 1,950 h, functionality: fully functional, pressing force: 48 t, bale length: 1,200 mm, bale width: 750 mm, bale height: 1,100 mm, bale weight: 550 kg, Equipment: documentation/manual, Automatic baler HSM VK 4812 The machine is maintained in perfect condition. The total operating hours are only 1950, and it has processed just 1314 bales of material. The machine was regularly serviced and has operated indoors in a warehouse since new. The baler has worked almost exclusively with non-abrasive material – textile offcuts. Key advantages of the unit: - Actual throughput: 6–13 t/h - Optimal continuous operation: 6–10 t/h - Very fast cycle time → ideal for use with conveyor lines - Significantly superior to the 15–22 kW version when processing a high material stream Technical data: Pressing force: 480 kN (≈ 48 tons) Motor power: 30 kW Connected load: approx. 32 kW Power supply: 3 × 400 V / 50 Hz Specific pressing force: 58.2 N/cm² Volumetric throughput: up to 332 m³/h Practical weight throughput: approx. 6 t/h (20 kg/m³) approx. 13 t/h (50 kg/m³) Theoretical (maximum) throughput: up to 16.6 t/h at 50 kg/m³ Idle cycle time: approx. 11.2 s Bale dimensions: 1100 × 750 × 600–1200 mm Bale weight: up to approx. 550 kg Pressing channel: 1100 × 750 mm Filling opening: approx. 1020 × 1250 mm We also have other balers in stock. Transport costs depend on weight, volume, and most importantly, distance. When making inquiries, please provide the following details: Delivery address (postal code and town/city name). For further details and transport options please contact us by phone, as additional arrangements require direct contact. Our contact details are available in the seller's legal information. Iedoy Sm Sqopfx Ag Ioib We sell and export worldwide; thanks to our extensive warehouse capacity, we can flexibly and quickly supply larger quantities as well. We issue intra-community invoices – VAT-free. Opening hours: Mon–Fri: 08:00–16:00 Sat: closed

Condition: excellent (used), functionality: fully functional, pressing force: 3 t, Orwak 5070 baler in perfect working condition. Fully serviced, new oil. Fully equipped – strap holders, straps, hook, bale trolley. Iisdey Sk H Sjpfx Ag Isb

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 26 t, Orwak 3325 baler in perfect working order. Fully serviced, new oil. Fully equipped. Comes with additional parts for wire tying. Iiodpfx Aey Sk Atjg Ieb

Condition: good (used), Year of construction: 2021, functionality: fully functional, pressing force: 58 t, Very good condition, fully functional, low operating hours, year of manufacture 2021, pressing force 58 tons. New price: seen for €19,500 Iedoyzw U Ujpfx Ag Isib Pressure cylinder has been dismantled for transport, inspection possible by appointment. Further presses in stock.

Condition: good (used), Year of construction: 2016, operating hours: 1,060 h, functionality: fully functional, Baler Dixi 80 SLD, with lifting/tipping device, semi-automatic, year of manufacture 2016 Manufacturer: Dixi Model: Dixi 80 SLD Year: 2016 Operating hours: 1030 Drive power: 11 kW, 400 V / 32 A Filling opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1000 kg/h Iijdpfx Agjy Ni Sho Ijb Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: triple, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: Paper, cardboard, film Note: The baler is in very good condition. It has been inspected and tested at our site in 28816 Stuhr. You can find the video on our website or YouTube channel. The hydraulic hoses should be replaced. If you have any questions about the machine, we are also happy to assist you by phone from Monday to Thursday, 08:00 to 14:00. On Fridays we are available from 08:00 to 13:00. Please note: All technical data is based on information provided by the manufacturer. We accept no liability for the information given or for any possible errors. The offer is subject to change, prior sale, and withdrawal at any time. Viewings are possible by appointment. Sale is ex-works, subject to prior payment, without warranty or guarantee.

Condition: good (used), Year of construction: 2019, functionality: fully functional, Baler Dixi 80 SLD, with lift/tilt device, semi-automatic, year of manufacture 2019 Manufacturer: Dixi Model: Dixi 80 SLD Year: 2019 Drive power: 11 kW, 400 V / 32 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Press cycle: approx. 35 s Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Tying: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: paper, cardboard, film The baler is in good condition. It has been inspected and tested by us. A video is available on our website or YouTube channel. If you have any questions about the machine, we will be happy to answer them by phone from Monday to Thursday between 08:00 and 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data are based on manufacturer specifications. We assume no liability for the information provided or for any potential errors. Isdpfx Asy Ni Rdsg Ieib This offer is non-binding, subject to prior sale and can be withdrawn at any time. Inspections are possible by prior arrangement. Sale is ex works, advance payment only, without warranty or guarantee.

Condition: good (used), Year of construction: 2017, functionality: fully functional, Baler Dixi 80 SLD, with lifting/tipping device, semi-automatic, year of manufacture 2017 Manufacturer: Dixi Model: Dixi 80 SLD Year of manufacture: 2017 Drive power: 11 kW, 400 V / 32 A Feed opening: 1,040 x 1,110 mm (W x L) Pressing force: 80 t Pressing cycle: approx. 35 s Capacity: approx. 1,000 kg/h Bale size: 1,120 x 1,120 x 1,200 mm (W x H x L) Bale weight: approx. 500-600 kg Strapping: 4-fold, manual Machine dimensions: approx. 4,320 x 1,830 x 2,620 mm (L x W x H) Machine weight: approx. 8,000 kg Materials: paper, cardboard, film The baler is in good condition. It has been inspected and tested by us. You can find a video on our website or YouTube channel. If you have any questions regarding the machine, we are also available by phone from Monday to Thursday, 8:00 am to 2:00 pm. On Fridays we are available from 8:00 am to 1:00 pm. Please note: All technical data is based on the manufacturer's specifications. We do not accept any liability for the information provided or for any possible errors. The offer is non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by appointment. Sale is ex works against advance payment, without warranty or guarantee. Ijdpfx Ajy Ni I Aeg Isib

Condition: good (used), Year of construction: 2013, functionality: fully functional, Dixi 60 SLS Baler, Year of Manufacture 2013 Isdoy Ni Hxopfx Ag Ioib Technical Data: Manufacturer: Dixi Year of Manufacture: 2013 Pressing Force: 60 t Drive Power: 11 kW, 32 A Filling Opening: 990 x 1110 mm (W x L) Bale Dimensions: 1100 x 800 x 1200 mm Bale Weight: approx. 370–450 kg Tying: 3-fold manual Machine Dimensions: approx. 4870 x 2100 x 2150 mm (L x W x H) Weight: approx. 5220 kg Materials: Paper, Cardboard, Foil The baler is in good condition. It has been inspected and tested by us. A video can be found on our website or YouTube channel. The operating manual and CE declaration are available. If you have any questions about the machine, we are happy to assist you by phone from Monday to Thursday, 08:00 to 14:00. On Friday, we are available from 08:00 to 13:00. Please note: All technical data are based on the manufacturer’s information. We do not accept liability for the accuracy or possible errors in the details provided. This offer is non-binding, subject to prior sale, and can be withdrawn at any time. Viewings are possible by arrangement. Sale is ex works, against advance payment, without warranty or guarantee.

Condition: good (used), Year of construction: 2013, functionality: fully functional, Baler Dixi 60 SLS, Year of Manufacture 2013 Technical Data: Manufacturer: Dixi Year: 2013 Pressing Force: 60 t Drive Power: 11 kW, 32 A Filling Opening: 990 x 1110 mm (W x L) Bale Size: 1100 x 800 x 1200 mm Bale Weight: approx. 370–450 kg Tying: 3-fold manual Iodpoy Ni Hrsfx Ag Isib Machine Dimensions: approx. 4870 x 2100 x 2150 mm (L x W x H) Weight: approx. 5220 kg Materials: Paper, Cardboard, Film The press is in good, fully functional condition and has been inspected and tested by us. A video can be found on our website or YouTube channel. If you have any questions about the machine, we are happy to assist you by phone from Monday to Thursday, 08:00 to 14:00. On Friday, we are available from 08:00 to 13:00. Please note: All technical data is based on manufacturer specifications. We assume no liability for the information provided or for any potential errors. This offer is non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by appointment. Sale by advance payment, ex works, without warranty or guarantee.

Condition: good (used), Year of construction: 2015, functionality: fully functional, Baling Press Dixi 60 SLD, Year of Manufacture 2015 Manufacturer: Dixi Model: Dixi 60 SLD Year of Manufacture: 2015 Drive Power: 7.5 kW, 400 V / 32 A Feed Opening: 990 x 1,110 mm (W x L) Pressing Force: 60 t Press Cycle: approx. 47 s Bale Size: 800 x 1,100 x 1,200 mm (W x H x L) Bale Weight: approx. 370–410 kg Strapping: 3-fold, manual Machine Dimensions: approx. 4,150 x 1,725 x 2,035 mm (L x W x H) Iiedpfx Ajy Ni Eueg Isb Machine Weight: approx. 5,420 kg Materials: Paper, cardboard, film The press is in good condition. It has been inspected and tested by us. A video is available on our website or YouTube channel. The operating manual and CE declaration are included. If you have any questions about the machine, we are happy to assist you by phone from Monday to Thursday, 08:00–14:00. On Fridays, we are available from 08:00–13:00. Please note: All technical data is based on information provided by the manufacturer. We do not accept any liability for the accuracy of the details or potential errors. This offer is subject to change, prior sale reserved and may be withdrawn at any time. Viewings are possible by appointment. Sales are ex works, against advance payment, without warranty or guarantee.