Pillar Drilling Machine

WMW BS 10/12

Year of construction: 2023, condition: new, - modern ergonomic design Kjdspbbc Hspfx Adqjnd - manual test with analogue Measuring Clock (Reading accuracy 0.2 HR) - easy to use and quick test process - Height Capacity approx. 185mm - Hepth Capacity approx. 160mm - Dimensions 545x182x755mm Test loads: 60 / 100 / 150kg Test method: HRA/HRB/HRC Standard delivery: - Hardness tester - V-Anvil - Flat Anvil Ø150mm - Flat Anvil Ø50mm - Ball Indenter 1/16" with ball - Diamond indenter 120° Rockwell - Spindle protection - Accessory case

Year of construction: 2024, condition: new, Make: DURMA Kjdpfed R Er Dsx Adqond Type: MS 2504 year of manufacture: 2022 cutting length: 2550 mm sheet thickness: 4 mm Control: EZM9910 Operating hours: 0 Cutting angle: 1°30 Strokes per min.: 42 motor power: 7,5 kW backgauge range: 750 mm table width: 450 mm table height: 800 mm dimensions L/W/H: 3200x2300x1350 mm Weight: 3780 kg Standard equipment control unit EZM9910 backgauge range 750 mm programmable via control unit Jvcmke Plastic inserts for hold-down 1 side stop and 2 sheet support arms Finger guard Portable foot switch with emergency stop Spring loaded stop in T-slot of the support arms Ball screw Ikh7877 Table plates with ball rollers Upper knife with 2 cutting edges Lower knife with 4 cutting edges CE marking Extended equipment Adjustable angular fence 0-180 The machine can be inspected and demonstrated at any time by appointment in our demonstration center in Staufenberg. Further machines are ready for demonstration at our facility in Staufenberg. We will be happy to provide you with further information on request.

Condition: good (used), Year of construction: 2005, For sale: 1 used spot welding machine incl. cooling system Manufacturer: Tecna Model: 6125 Year of manufacture: 2005 Hyfra cooling VWK 50-1-S, year 2006 Kodpfjuii A Aox Adqond Documentation included The machines can be inspected at our warehouse in 09599 Freiberg.

Condition: excellent (used), Year of construction: 2016, Centre height 200 mm Maximum swing over bed 400 mm Maximum swing over cross slide 235 mm Swing in gap 550 mm Bed width 320 mm Distance between centres 1000 mm Bar capacity 50 mm Spindle bore 52 mm Number of spindle speeds 12 Speed range 50–2240 rpm Number of feeds 80 Kodpexbzpmefx Adqjnd Weight 1700 kg

Condition: used, Year of construction: 1999, sheet width 3000 mm plate thickness 3 mm 3 support arms 1 angle stop pneumatic hold-down device Knodpfor Ngtijx Adqsd Backgauge to be operated by hand

Condition: excellent (used), Year of construction: 1995, Combination Unit: Manufacturer: GSG Feeder: Type: 840.02-027 Crusher Descaler: Type: 663.02-017 Wire Range: Ø5.5-16mm For wire rod with approx. 40-60 daN/mm² strength Crushing and Bending Rollers: Carbide Inserts Adjustment with 0.37 kW - 1.15 A gear motor Brush Drive with 0.25 kW gear motor, n=293 rpm Connection Voltage: 380-420 V 50 Hz Dry Coating Unit: Type: BSG/T Filling: Calcium Stearate (e.g., Traxit Type: D S 51 E) Stearate Consumption: approx. 350 g per t of wire Drawing Speed: max. 15 m/s Electrical Power: 2x 0.55 kW gear motors Cassette: 2 slots (supplied with 1x roller block + 1x cassette) Type: PKG/T (TS) Cleaned rolled wire Wire strength approx. 40–60 daN/mm² Wire range max. inlet diameter 9.5mm, finished diameter 3.5–8.5mm Roll dimensions min. Ø115mm, max. Ø125mm, Bore diameter Ø82mm, width 15–25mm Cooling pin diameter 25mm Cooling water consumption approx. 600 l/h Drawing machine: Manufacturer: Koch Type: KHZ 5000 Year of manufacture: 1993 Serial number: 13.821 Number of draws: 1 draw per block Drawing drum: Ø700mm Tensile force: mechanical 5000 N Wire material: mild steel wires Run-in strength: approx. 40 – 45 daN/mm² Maximum drawing range: Inlet diameter 5.0 – 8.5mm Cross-section reduction: 20 x 25% (mechanical gradation) Drawing speed: up to max. 7.0 m/s Brake: Twiflex, type: MRB Drive: AC motor/frequency converter, Siemens PN=110 kW, n=1485 rpm Spooler: Manufacturer: Koch Type: KHS 1250 Year of manufacture: 1993 Factory No.: 13741 Wire diameter: 5 – 8.5 mm Strength: approx. 55 – 70 daN/mm² Kedpfer Nfvmsx Adqjnd Winding speed: V=7 m/s, adapted to the drawing machine Filling weight: approx. 3000 kg Spool drive motor: Three-phase motor with external fan Type: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000-2000 rpm, IP54, design B3 Laying drive motor: 66-671U, 1.5 kW, 170 V, 9.8 A, 1680 rpm, IP 44, B5-200 With Attached tachometer generator TG 20, 20 V / 1000 rpm With attached spur gear SK 32, i=57.53, design B6 Hydraulics: Hydraulic excavator type: H13 AK Pneumatics: Twiflex disc brake type: MRB Pneumatic cylinder type: SPWG 28032-25mm stroke Dimensions: 3100 x 3000 x 1700 mm (L x W x H) without counterweight

Condition: excellent (used), Year of construction: 2003, The machine has very few working hours and has been in storage for many years) Performance: Hole diameter and thickness up to max.: approx. 28×13 mm Angle steel 90 degrees up to max.: 80x80x8 mm Angle 100x 100 x 10 Kjdpfx Asupzf Redqsnd Flat steel up to max.: 300 x10/ 200×13 mm (See also rating plate in the appendix). Machine weight: approx. 750 kg Various punches are also included with the machine

Year of construction: 1978, condition: ready for operation (used), Drilling spindle stroke: 160mm, spindle taper: MK4, spindle speed: 1750rpm, reach: 300mm, feed: 0.3mm/rev, table dimensions X/Y: 620mm/470mm, machine dimensions X/Y/Z: approx. 620mm/950mm/1900mm, weight: approx. 450kg. Includes coolant system and threading device. An on-site inspection is possible. Knsdpfx Adjxc Ni Doqsd

Condition: used, Technical details: grinding wheel diameter: 200 mm voltage: 220 380 V / Hz revolution per minute: 3000 U/min total power requirement: 900 Watt Knjdpfx Adeu Ngu Seqsd weight: 22 kg dimensions L x W x H: 0,23 x 0,46 x 0,25 m Double sanding block; table-top unit with sanding supports left/right, horizontally adjustable 30mm max. sanding discs Ø 200mm max. grinding wheel thickness 32mm currently clamped sanding discs on the sanding block: left = Ø 190mm x 30mm type H50 and right = Ø 180mm x 32mm type M20 *

Condition: good (used), Year of construction: 2005, Straight and cut machine Brand - RAVNI ( France ) Min/Max wire diam. - 4- 10 mm Max cutting length - 6 meters Construction year - 2005. Knodpfx Adjpxnv Doqjd