Angular Clamping Device

WMW AW 1300x1000x1600 (Nr. 3-6)

Condition: excellent (used), Year of construction: 1984, functionality: fully functional, turning diameter over cross slide: 630 mm, spindle bore: 320 mm, turning diameter: 1,200 mm, turning diameter over bed slide: 930 mm, turning length: 3,000 mm, Lathe in very good technical condition, has seen very little use and was not used for machining pipes. The Poręba TPL 90/3m lathe (also listed in market nomenclature as a variant of the TPK 90 series) is a textbook example of an Oil Country Lathe / Hollow Spindle Lathe. This model fulfills all the specific criteria for machines intended for the Oil & Gas sector: • Massive spindle bore (Big Bore): This version features a spindle bore with a diameter of 320 mm (approx. 12.5 inches), allowing for easy insertion of thick-walled drill and casing pipes. • Dual chucking system: The headstock is designed for mounting two independent lathe chucks (front and rear, typically 28 inches in diameter), ensuring the pipe is clamped and stabilized at both ends of the spindle. • Optimal working dimensions: The 3m designation defines a turning length between centers of 3000 mm, which, combined with a swing over bed of 930 mm (hence the "90" in the name), allows for machining heavy-duty pipeline components. • Exceptional rigidity: FUM POREBA factory machines are renowned for their monolithic, very wide and heavy cast iron beds, which effectively dampen the immense vibrations generated during taper thread cutting. In international used machinery catalogues, this specific Poręba model is directly classified under the Oil Field Lathes category. TECHNICAL SPECIFICATIONS: Geometric parameters and machining ranges • Swing over bed: 930 mm / 36.6 in • Swing over cross slide: 630 mm / 24.8 in • Swing in gap: 1200 mm / 47.2 in • Maximum turning length between centers: 3000 mm / 120 in • Bed width: 585 mm / 23.0 in Headstock Dsdsy Sf Azopfx Al Aowc • Spindle bore diameter (Hollow Spindle): 320 mm / 12.6 in (in US nomenclature classified as a 12.5" version) • Spindle speed range: 5 – 250 rpm, or modified versions up to 710 rpm • Number of spindle speed steps: 18 Feed and thread cutting system • Longitudinal feed range: 0.1 – 12.8 mm/rev / 0.004 – 0.504 in/rev • Cross feed range: 0.05 – 6.4 mm/rev / 0.002 – 0.252 in/rev • Types of threads cut: Metric, Inch (Whitworth), Module, Diametral Pitch (DP) Tailstock • Tailstock quill diameter: 130 mm / 5.1 in • Tailstock quill travel: 300 mm / 11.8 in • Internal taper of quill: Morse No. 6 (MT6) Drive and dimensions • Main motor power: 22 kW / 29.5 HP • Overall length: approx. 5500 mm / 216.5 in • Overall width: approx. 1750 mm / 68.9 in • Overall height: approx. 1500 mm / 59.0 in • Total weight: approx. 8000 kg / 17,630 lbs

Condition: excellent (used), I am selling this machine, connected, can be tested. Max. workpiece diameter ..... 1600 mm Module ..... 16 - Dwedpfjv Nqppjx Al Ajc Power of the main electric motor ..... 12 kW Dimensions l x w x h ..... 4300 x 2000 x 3170 mm Machine weight ..... 18500 kg Can send a video of the machine, via whatsapp.

Condition: used, Table unit from a DROOP & REIN portal milling machine Clamping plate with T-slots made of cast steel gray cast iron Table unit with clamping plate and very solid guideway Table clamping surface 5500 x 2000 mm Travel of the table clamping plate approx. 3100 mm Table height 1050 mm Dedpfjthuzpex Al Aewc Table load: max. 20 tons Ball screw: Ø 100 mm Thread pitch: 20 mm (single-start) - Processing table guided very stably on the bed - Metal telescopic guideway cover - comes from a DROOP & REIN portal milling machine - Longitudinal table movement via ball screw and SIEMENS servo motor - Clamping surface with 11 T-slots 28 mm - Drive via SIEMENS 1FT6134-6AB71-1AG2 servo motor with IC200448S/R encoder (RN 000 B25) Total length 9500 mm Width 2000 mm Overall height 1050 mm dead weight 28 ton. good condition

Condition: used, Technical details: turning diameter over bed: 830 mm turning dia. over face-slide: 540 mm turning length: 3000 mm turning diameter over support: 540 mm centre distance: 3000 mm faceplate diameter: 800 mm Rapid feed X axis: 4 m/min. control: MTC K (Monforts) range of revolution per miute: 2 -1.600 U/min spindle passage: 88 mm tailstock taper ISO: MK6 tailstock quill stroke: 200 mm max. workpiece weight between centers: 1250 kg max. workpiece weight -without tailstock: 3000 kg turning dia. in gap: 1.200 mm length of gap: 310 mm Weight approx.: ca. 6.85 (ohne Späneförderer und Kühlmittelbehälter) t dimension machine xH: 2,55 x 1,1 x 1,29 m Dwjdpfx Aswmlknsl Asc Cycle lathe Machine overhauled in 2010 Operation via control panel Thread cutting by calculation Interpolator of NC control Chip conveyor manufacturer Cable drag Three-jaw chuck D=500mm without clamping jaws Various accessories *

Condition: new, functionality: fully functional, machine/vehicle number: 8153336470, overall weight: 616 kg, volume flow: 399 m³/h, pressure (min.): 4 bar, pressure (max.): 13 bar, noise level: 67 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, We are a company specializing in the compressed air industry for over 20 years. Professional level of service and high quality goods offered by our company - "proven" on the market - guarantee successful cooperation with you. Djdpswlp Hdsfx Al Ajwc We offer NEW screw compressor Atlas Copco GA37VSDs FF (variable speed with built-in dryer) Machine equipped with frequency converter (inverter), manufactured based on the latest technologies, which translates into greater efficiency and performance: On average 20% lower unit energy consumption (SER) than in previous models of the GA VSD series. Ecological and efficient VSD+ variable speed drive system reduces energy consumption by an average of 50% compared to models that operate at idle speed. Regardless of energy savings, efficiency (FAD) increases by up to 12%. Efficient fan motor (compliant with the ERP 2015 directive) reduces energy consumption and noise level. Superior Motor Efficiency (iPM) up to 94.5% exceeding IE3 efficiency levels. Built to work hard for your success. The industry-leading GA Series oil-injected rotary screw compressor delivers unmatched efficiency, high productivity and low cost of ownership – even in the harshest conditions. Technical data: capacity at 4 bar: 15.69- 13.75 l/s / 0.94-7.85 m3/min capacity at 7 bar: 15.67-129.35 l/s / 0.94-7.76 m3/min capacity at 10 bar: 15.68-110.79 l/s / 0.94-6.65 m3/min Max pressure 10 bar (13 Bar variant on request) Voltage 400 V Motor 37 kW Noise 67 dB(A) Weight 616 kg Motor with internal permanent magnets (IPM) Compression element Direct drive Innovative fan Separator/oil filter with durable construction Electronic water drain valve that does not cause compressed air losses Controller Elektronikon Inlet valve VSDs module Manufacturer code: 8153336470 If you are not sure whether the device is right for you, you have not found the right compressor, CALL! We will advise you on the right choice of device. We invite you to familiarize yourself with our full offer.

Condition: as good as new (ex-display), JAN REILING BV has an extensive warehouse with more than 15,000 different DEMAG craneparts, from a nut to a complete crane. In addition to new parts, we also supply used parts, hoists and cranes. Our used hoists, cranes, parts and drives are ready in our warehouse completely overhauled. JAN REILING BV immediately supplies what you are looking for. JAN REILING BV has built up an extensive supplier network within Europe. In addition to DEMAG, we can also supply you with parts from all other brands quickly and affordably. We supply various Demag parts new from stock, such as a: ropeguides Rope brakes hoistingmotors drivingmotor gearbox brake hoisting motor bottomblock loadhook runningwheels trolley pushbutton Djdpfxeh Upyhe Al Aowc radiocontrol cabledrum types like : KBH KBF KBS KBA KBU 13/3PF 13/6PF 13/3KF 13/6KF 16/6KF 16/8KF 52D 52DF 62D 62DF 63D 63DF 72D AFW D04 D05 D06 D08 ZBA ZBF ZBR DH P100 P625 P632 P425 P408 P412 P1250 P1050 P1600 P2100 DH DMR DR DC PK DK contact us for the possibilities We supply both new and used

Condition: used, Technical details: honing diameter: Ø 400 mm stroke: 600 mm throat: 390 mm table-size: 1.550 x 780 mm table surface area: 1.400 x 480 mm table:: fest total power requirement: 4,1 kW Weight approx.: 2,8 t Dwodpeu Ngybofx Al Aec dimension machine xH: 2,0 x 1,2 x 4,35 m Further technical details: - longitudinal travel of machine table approximately 500mm - cross travel of machine table approximately 200mm - working height 350mm (non-adjustable) - distance column / table 0 - 200mm Equipment: - oil tank Ø 300 x 600mm - control panel i.D. *

Condition: excellent (used), Motor-driven rotary shift table Stepless rotary table (pitch 0.001°) Manufacturer: Rückle Type: PKT 6 Dwodeif Rlbopfx Al Aoc Clamping surface: 1600 mm x 1600 mm Travel lengthwise: W-axis = 1000 mm Condition: Very good (used)

Condition: used, functionality: fully functional, Year of construction: 2007, operating hours: 22,372 h, laser hours: 11,345 h, laser power: 4,000 W, sheet thickness steel (max.): 20 mm, sheet thickness aluminum (max.): 8 mm, overall weight: 16,000 kg, total length: 11,600 mm, total width: 5,200 mm, total height: 2,200 mm, working range: 40,002,000 mm, Equipment: cooling unit, Standard Features: • Enclosed machine frame with integrated laser unit • Laser unit: TruFlow 2000 CO₂ laser with high-frequency excitation, maintenance-free turboradial blower, reflector telescope, cooling unit, logbook function • Automatic pallet changer • Longitudinal conveyor belt for small parts/waste • Drive: Maintenance-free three-phase servo motors • Cutting head quick-change device Laser cutting head with 5" lens and laser cutting head with 7.5" lens • Programmable cutting gas pressure setting • ControlLine capacitive height control and process control • Automatic focus adjustment with FocusLinePlus • Laser power control • Positioning laser • NitroLine high-pressure cutting Dedev Sm Ruspfx Al Aewc • Fast processing with SprintLine • Automatic production of smaller holes • PlasmaLine plasma sensors • Automatic sheet metal surface and edge detection • Programmable Performance cycles • Microweld • Spray device for safe thick sheet processing • Automatic blow-off system • Residual heat extraction • Sinumerik 840D control system: Open PC-based control, easy operation, online help, integrated e-shop, diagnostic functions, maintenance logbook, technology data, teleservice • TruTops Laser lite workshop programming Safety: • Multi-beam light barriers, fully encapsulated and ventilated beam guidance, monitoring system, multi-chamber extraction and compact dust extractor, protective cabin • RJ45 network connection via installation via teleservice • 3.5" floppy disk drive • TFT color display More powerful lasers: • TruFlow 4000, including NitroLine Plus, nitrogen beam tube ventilation and lens monitoring sensors Extended machine equipment: • PierceLine Process Control System • A total of 2 Machine auxiliary pallets, structural steel webs • Crane-mounted traverse for manual pallet handling • Pneumatic cutting

Condition: used, Technical details: table length: 3600 mm table width: 3600 mm table load: 50 t table travel: 2000 längs / longitudinal mm table height over floor: 1350 mm table speed: ca. 1000 mm/min table rotating: 360 ° total power requirement: 14 kW weight of the machine ca.: 38,5 t dimension machine xH: 5,5x3,7x1,4 m space requirements of the machine approx.: 6,2x3,7x1,4 m Main areas of application: -Multi-sided machining -Supplement for travelling column milling machines or boring mills Electric and mechanics of the Rotary Table have been overhauled. - newly equipped with a digital measuring system (DRO) for x-travel and rotation - control via control panel - table clamping plate 14t weight - table load capacity 50t 11 pcs T-slots according DIN 650: - a=42mm - h=75mm - b=70mm - c=31mm Rotary Table can be inspected under power! Following work has been proceeded: - Integration of a Digital Read Out (DRO) for the x axis and a rotary encoder for C-axis - integration of a control via a control panel Dsdsu N D Rqopfx Al Aewc - renewal of hydraulic pipes / hoses, screw connections, manometers, flow chokes and filters - bearing of both axis transmissions - control cabinet and complete machine cabling has been renewed - end positions cleaned, checked, adjusted and defective replaced by new ones - frequency converter for continuous speed retrofitted - preparation of the necessary documentation (operating instructions, electrical and hydraulic diagram) - cracked gearbox housing repaired via casting lock - renewal of the guideway wipers - processing of the guideway cover including new wipers - machine has been repainted - renewal of axis drives - feed gear cleaned and resealed - feed motor new bearing installed *