Demag hoistmotors & craneparts

Demag

Year of construction: 1995, condition: good (used), DEMAG Electric Hoist DKUN 5-500-K-V1F4 Hjdpfxoudv Tks Ahvofd Type: Electric chain hoist Year: 1995 Chain: 3 meters Three-phase 380V Capacity: 1.000Kg 2 speeds (12,5m/min. - 6,2m/min.) 1.7Kw

Condition: used, Year of construction: 2011, functionality: fully functional, Quick steam generator set - Jumag consisting of 3 quick steam generators including water softening system and chemical dosing system 1x Jumag DG 360 Volume: 60L Operating pressure: 13 bar Max. heat output: 245 kW Hsdswn H Aujpfx Ahvefd Steam output: 360 kg/h Gas burner: Weishaupt WG30N/1-C-ZM-LN Year: 2011 2x Jumag DG 320 Volume: 49L Operating pressure: 13 bar Max. heat output: 200 kW Steam output: 320 kg/h Gas burner: Weishaupt WG30N/1-C Year: 2002

Condition: good (used), Year of construction: 2011, functionality: fully functional, travel distance Z-axis: 1,500 mm, Equipment: documentation/manual, Number of axis: 3 Reach: 1500 mm Payload: 5 kg X=420mm Y=1200mm Hfodsyfhw Hjpfx Ahvsd Z=1500mm c= 0-90 pneumatic

Condition: new, DEMAG control box / switch cabinet for hoist / wire rope hoist - DR / DMR / DH 1. Demag control box DR / DMR with frequency inverter DIC - 4 - 007 - C - 0032 - 05 2. Demag control box / switch cabinet for DH hoist Hedpfx Aoyut Aaohvefd

Condition: used, Twin-shaft shredder Manufacturer: Fransson Weight: 1500 kg Mouth width: 750 mm x 680 mm Hfsdpjycv Uhofx Ahvjd With sieve Mesh diameter 50 mm Capacity: from 20-50 m3 per hour Equipment after repai

Condition: used, DEMAG hoist motor / crane motor. Hoist motor type - KBH 100 B 8/2 - 2 units Hedpfx Asxpw Iujhvefd

Condition: ready for operation (used), Year of construction: 2013, operating hours: 27,551 h, clamping force: 2,200 kN, total height: 2,100 mm, This SUMITOMO SHI DEMAG IntElect 220/610-750 smart was manufactured in 2013. It's an electrical injection moulding machine known for its precision and efficiency. Ideal for those looking to enhance their production capabilities with reliable technology. Contact us for more information. Additional equipment Hsdjx D Hnyopfx Ahvjfd • Sepro Robot SDR 22 Machine Benefits Technical Machine Benefits • Screw diameter: 45 mm / screw geometry: standard / l/d ratio: 20 / specific injection pressure: 2150 bar / maximum shot volume: 329 cm³ / maximum shot weight: 293 g / injection rate without accumulator: 254 cm³/s • Dosing stroke: 207 mm / maximum nozzle stroke: 450 mm / nozzle immersion depth: 20 mm / nozzle contact force: 58 kn / number of heating zones: 4 / hopper capacity: 50 l / maximum injection speed: 160 mm/s • Holding force: 2420 kn / maximum opening stroke: 550 mm / minimum mold height: 300 mm / maximum mold height: 580 mm / maximum platen distance: 1130 mm • Mold clamping plates (hxv): 880x830 mm / clearance between tie bars (hxv): 610x560 mm / ejector stroke: 150 mm / ejector force: 58 kn • Dry cycle time according to euromap 6 (stroke): 427 mm • Net weight without oil: 10100 kg Dimensions Machine Depth 6460 mm

Condition: excellent (used), Year of construction: 2015, functionality: fully functional, Equipment: type plate available, Two professionally disassembled compressors from the manufacturer GEA Bock. Technical data sheet available, see images. Hfedpfowuvquox Ahvod

Condition: ready for operation (used), Year of construction: 2003, operating hours: 96,986 h, clamping force: 600 kN, screw diameter: 30 mm, This DEMAG ET60-200 concept hydraulic injection moulding machine was manufactured in 2003. It features a clamping force of 600 kN and a maximum mold weight of 580 kg. The machine includes a robust injection unit with a screw diameter of 30 mm and an injection pressure of 1900 bar. Consider the opportunity to buy this DEMAG ET60-200 concept hydraulic injection moulding machine. Contact us for further details. • Clamping unit: • Tie bar spacing (H x V): 420 x 420 mm • Platen dimensions (H x V): 530 x 540 mm • Min. mold installation height: 210 mm • Opening stroke: 400 mm • Max. mold weight: 580 kg (moving side 380 kg / fixed side 200 kg) • Ejector: • Stroke: 125 mm • Force: 41 kN • Retraction force: 15 kN • Pneumatic ejector: Yes • Core pull control: Yes (2 units, on the ejector side/AS) • Injection unit 1: • Unit size: 200 • Screw diameter: 30 mm • Injection pressure: 1900 bar • Stroke volume: 106 ccm • Shot weight (PS): 94 g • Screw L/D: 20 • Nozzle radius: 15 mm • Armored/wear-resistant injection unit: Yes • Process control: SPC (Yes) • Note: Maximum crane load warning: 2 metric tons Hfedpsyg Nfusfx Ahvjd Additional equipment • Robot/removal device: W621-1381 • Travel paths: Y 1200 mm, X 550 mm, Z 1500 mm • Hot runner controller: 7-zone integrated control • Mold sensors: Kistler (p=1/t=0)

Condition: ready for operation (used), Year of construction: 2015, operating hours: 15,642 h, screw diameter: 45 mm, total height: 2,213 mm, overall weight: 15,750 kg, This SUMITOMO SHI DEMAG Systec SP 350/720-840 was manufactured in 2015. It is a hydraulic injection moulding machine, ideal for precision plastic processing. Consider the opportunity to buy this SUMITOMO SHI DEMAG Systec SP 350/720-840 hydraulic injection moulding machine. Contact us for more information. Additional equipment • Fanuc Robot Machine Benefits Qualitative Machine Benefits • Process data acquisition, mould protection Technical Machine Benefits • Mould height min: 350 mm / mould height max: 745 mm • Main electronic connection: 3/400 v 50hz • Programmable sequence, highly dynamic feed speed, hydraulic pressure-dependent holding pressure control, digital/wear-free position measuring system. Extra Information Standard equipment: Support of the moving mould mounting platen via linear guides/ Ejector short / long stroke/ Interface for external printer (hardcopy)/ Individual axis movement optimization (activeAdjust)/ Four-stage mould closing and four-stage mould opening sequence/ Pump drive power II, increased (59.0 kW)/ Mains voltage 400 V ±10% / 50 Hz, 3 phases + N + PE/ Mains connections drive / heating separate/ Data display coloured/ Oil cooler reinforced (cooling water supply up to 35 °C)/ Water connection for mould and machine cooling separate/ Basic version Europe/ Corrosion protection/ Paint finish: Deep black (RAL9005): Machine bed with internals, lower switch cabinet/ Signal white (RAL9003): Clamping unit, injection unit, nozzle guard/ Signal white (RAL9003): Fixed safety devices, upper switch cabinet/ Signal white (RAL9003): Safety doors/ Textured surfaces: Elastic machine bearings/ Digital and wear-free position measuring system (ultrasound/high-resolution rotary encoders for injection, mould and ejector movement)/ Mould connection dimensions type E (according to EUROMAP March '96)/ Centring diameter fixed platen: 160 mm/ Centring diameter moving platen: 160 mm/ Without side ejector plate/ Standard mold installation height: Min: 350 mm/ Max: 745 mm/ Standard closing speed (movements only when safety gate is closed)/ Ejector with position control (p/F+v independently programmable, parallel to mold movement)/ Toggle lever oil lubrication/ Injection unit/ Optional equipment: Speed-controlled pump Servo Technology (activeDrive)/ Emergency stop switch on operator side/ Separate opener for ultra-fine filtering in the bypass (activeCool&Clean)/ Socket 1 x Schuko (230V / 10A), can be disconnected via main switch/ Socket IECEE 3Ph / 400V-16A, can be switched off via main switch/ Flashing light/ Operation with safety door open (operator side)/ 6 pneumatic 5/2-way valves on movable tool plate (programmable)/ 6 pneumatic 5/2-way valves on fixed tool plate (programmable)/ Central maintenance unit for pneumatic valves/ Core pull 1-circuit via proportional valve (programmable, with non-return valves)/ Manual pressure relief for core pull 1-circuit/ Protective clothing on operator side widened (250 mm)/ Hot runner control 12 zones, integrated (2, 75 kW)/ Pneumatic hot runner nozzle control (1x 5/2-way valve)/ Clamping force control/ Active mold protection via sensor when closing (activeQ)/ Manually adjustable monitoring switch for mold open position/ Central grease lubrication (manual)/ Material hopper for automatic filling/ Hopper shut-off with emptying option/ Holding pressure switchover dependent on hydraulic pressure (with pressure recording)/ Nozzle contact pressure when mold is open (programmable)/ Hjdpfxex D Hnte Ahvefd

Condition: used, Year of construction: 2007, Used Grasso 6210 reciprocating compressor on NH3 (Ammonia). Complete with a Leroy Somer PLS225MR-T electric motor - 50/60 Hz - 55/63 kW - 1455/1765 RPM, 2 Grasso OS3 oil separators, and pressure and safety switches/gauges. The compressor has a displacement of 432 m³/h. Hsdpfjrlk Afox Ahvofd

Year of construction: 2019, operating hours: 17,716 h, condition: ready for operation (used), General Data Measurements width 1920 cm Measurements depth 7750 cm Machine weight 26210 kg Measurements height 2410 mm This SUMITOMO SHI DEMAG El-Exis SP 350/820-920 was manufactured in 2019. A robust electrical injection moulding machine with a screw diameter of 40 mm and a clamping force of 3,500 kN. It has operated for 17,716 hours with 12,440,761 cycles, ensuring extensive production capabilities. Consider the opportunity to buy this SUMITOMO SHI DEMAG El-Exis SP 350/820-920 electrical injection moulding machine. Contact us for more information. Application Types Injection Moulding Hsdpfjx D Nx Isx Ahvsfd

Year of construction: 2019, condition: ready for operation (used), This DEMAG Systec 210/580-840 was manufactured in 2019. It's a hydraulic injection moulding machine with a clamping force of 210 tons and a power output of 60 kW. It has been used for 31,132 operating hours. Consider the opportunity to buy this DEMAG Systec 210/580-840 hydraulic injection moulding machine. Contact us for more information. • The dosing unit (orange part) is not included. • Integrated socket combination, country-specific, • can be switched off via main switch and shutdown program • 2 x Schuko 1Ph/230V/16A; 2 x IECEE 3Ph/400V/16A residual current device • Pneumatic 5/2 valve No. 1 on movable mold clamping plate; • programmable, supplied via central air connection • includes hoses. Inputs and outputs freely programmable; 3 inputs and 3 outputs; • Terminal point outside the control cabinet • Interface for additional nozzle heating band; socket only • 2-circuit core puller via switching valve on movable mold clamping plate; Q-independent (programmable); • With pilot-operated check valves to prevent core creep • Mold connection dimensions E (similar to Euromap March 96) • With side ejector plate, centering diameter of fixed platen: 160 mm Hfedjx D Nlujpfx Ahvod • Centering diameter of movable platen: • Mold installation height increased by 100.0 mm • Min: 340 mm • Max: 790 mm

Condition: as good as new (ex-display), For sale Hoist motor used/reconditioned for a DH wire rope hoist NB! Hedpjh Up U Dsfx Ahvjfd we have more than 15,000 Demag parts in stock see our website or other ads

Year of construction: 2005, condition: ready for operation (used), This SUMITOMO SHI DEMAG El-Exis S 250/630-1450 was manufactured in 2005. It features a central accumulator for high-speed injection and chromed tie bars. The pump drive power is 22.0 kW, with a mains voltage of 400 V/50 Hz. It includes a color data display with VGA interface, an oil cooler, and electric screw drive. Consider the opportunity to buy this SUMITOMO SHI DEMAG El-Exis S 250/630-1450 hydraulic injection moulding machine. Contact us for more information. • 5x similar units available • Central accumulator for high-speed injection; core, ejector, and nozzle movement • Nozzle movement parallel to mold movement • Chromed tie bars on clamping unit • Pump drive power: 22.0 kW • Mains voltage: 400 V / 50 Hz, 3 Ph + N + PE • Separate mains connections for drive and heating • Control: color data display with VGA interface and AT keyboard interface • Injection, holding pressure, and back pressure via servo valve • Reinforced oil cooler • Separate water connections for mold and oil cooling • Compliance: Basic version Europe, according to valid safety regulations • Painting: Bottom anthracite grey RAL 7016; Top blue 571C MD • Elastic machine mounting • Ultrasonic displacement measuring system with digital data transmission for injection, ejector, mold (WZ), and nozzle (AWH) movements; 1/100 mm resolution for injection axis Hjdpfox D Rqrex Ahvjfd • Reduced centering diameter (D=100/125) for fixed mold platen • Mold connection dimensions type E (similar to EUROMAP), without side ejector plate • Standard mold installation height • Safety interlock: mold opening and ejector forward only with closed safety door • Ejector with position control via proportional valve; pressure and velocity independently programmable • Electric screw drive, frequency-controlled