Large flanging device

Trumpf Großer Bördelapparat CN 20 CS 20

Condition: ready for operation (used), Year of construction: 1969, Centre height: 355 mm Centre distance: 3000 mm Max. swing diameter over bed/gap/cross slide: 715/790/520 mm Spindle bore: 86 mm Spindle mount according to DIN 55027: Size 11 Quill taper of tailstock: MK 5 21 spindle speeds: 5.6 - 560 rpm 42 feeds longitudinal/cross: 0.09 - 5.6/0.045 - 2.8 mm Kdsdpsxpuu Eofx Aa Eep 22 Whitworth threads: 2 - 28 TPI 28 metric thread pitches: 1 - 14 mm 27 module thread pitches: 0.25 - 3.5 module 32 module threads: 4 - 56 module 32 diametral pitch threads: 8 - 112 DP Drive motor, pole-changeable: 380 V, 7/11 kW Weight approx.: 7 t Space requirement approx.: 6000 x 2300 mm

Year of construction: 1979, condition: used, throat: 22/29 mm Kdodpfszif Sox Aa Eep drive motor: bei 380 V ca. 0,55 kW space needed: 450 x 500 x 560 mm weight: ca. 6,5 kg pressure power: 30 kN

Condition: used, Radial drilling machine CSEPEL, Type RFh 75 / 1500 Machine no. 13704, Year of manufacture 1985 Drilling capacity in steel: Ø 75 mm Drilling capacity in cast iron: Ø 90 mm Spindle mount: MK 5 Nominal overhang: 1500 mm Maximum overhang of the spindle: 1500 mm (to the column) Minimum overhang of the spindle: 440 mm (to the column) Distance from spindle nose to clamping surface: 370 - 1700 mm Overarm vertical adjustment: 950 mm Table size / clamping surface: 1800 x 1100 mm Column diameter: 450 mm Quill stroke: 380 mm Spindle speed: 19-1900 rpm, 21 steps Feed rate: 0.047-2 mm/rev, 12 steps Motor power: 11 kW Mains connection: 380 Volts, 50 Hz, 15 kW - Right-hand and left-hand rotation of the drilling spindle via hand lever switch - Hydraulic gear change for spindle speed and feed rate - Hydro-mechanical central clamping device Kodpfx Aslhwr Roa Eedp - Motorized overarm vertical adjustment - Without coolant system - Machine light - Operating manual Space required: Length 2720 mm x Width 1170 mm x Height max. 3770 mm Transport height with motor on the column: 3500 mm Transport height without motor on the column: 3250 mm Weight: 6.3 tons Good condition

Condition: good (used), Make: Ursviken Type: VPF 1000/800-5,0 Control: Siemens Simatic panel Year: 1970 Hydraulic press for fabrication off large componts like dish heads tanks boiler shipyard and steelconstruction Renewed in 2015 with Siemens SIMATIC panel and E-Cabinet Rittal Build in height 2950 mm Maximum die height 1500 mm Movable Table & Piston in X-Ways Large package Die tooling radius 10/20/30/50/60/80/100 Pressing force 210 kg/cm2 Maximum stroke 800 mm Machine 2350 mm placed in ground Specifications Metric US Standard Capacity Kg 1000 Ton Distance between column 5010 mm Table Length 3000 mm Table Width 2000 mm Table Height 550 mm Ram stroke 1450 mm Approche speed 50 mm/min. Working speed 5 mm/min. Return speed 50 mm/min. Dimensions (Estimate) Length 0 mm Width 0 mm Height 0 mm Weight 0 kg Kdsdokvmi Sopfx Aa Eep Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: excellent (used), Motorized 3x3 welding column with movement control by pushbutton panel. Useful capacity: 3x3m Wire spool dispenser Lincoln Idealarc DC-1000 submerged arc equipment with torch and flux holder + Lincoln NA-3N Amps and Volts regulation panel. Submerged arc duty factor: 1000 Amps at 100%. Kdodju Afttspfx Aa Ejp Idealarc® DC-1000 Submerged Arc Welder Input voltage: 230/460 Input current: 193/96.5A Input Hertz: 60 Input phase: 3 Input power: 230/460/3/60 Mode icon: DC/DC Output range: 150-1300A DC,16-46V Polarity: DC Nominal output: 1000A/44V/100%

Condition: as good as new (ex-display), MIG/MAG welding machine with inverter technology. Three-phase power supply, welding machine. Master Software TERRA PME included. Technical data Power Supply: Kdjdpfsw Rm Sasx Aa Eep Voltage (50/60 Hz): 3x400V ±15% Maximum input power: 22.9 kVA Maximum input current: 31.1 A Power factor PF: 0.73 Efficiency: 89% Slow-blow fuse: 25 A Open-circuit voltage: 61Vdc IP protection class: IP23S Insulation class: H Power cable: 4x3mm² – 5 m Welding: Setting range: 3–400A Duty cycle MIG/MAG at 40°C: 40% – 400A, 100% – 330A Duty cycle MIG/MAG at 25°C: 100% – 400A Wire diameter: 1.0–1.2 mm (optional 0.6–1.6 mm) Flux-cored wire diameter: 0.9–2.4 mm Aluminum wire diameter: 0.8–1.6 mm Wire feed speed: 0.5–22.0 m/min Wire spool diameter: Ø 200/300 mm Remote control connection: yes

Condition: good (used), Year of construction: 1998, machine/vehicle number: 0618012, Offer 24604 Ksdpovncubsfx Aa Esdp Technical data: - suitable for welding steel, aluminum, special metals, Cr Ni, etc. - welding current 450 A 60% ED - 360 A 100% ED - welding current adjustable from 3 A - 450 A - Synergic setting control FRONIUS - water cooling device FRONIUS - separate wire feed case - intermediate package device - wire feed case 1 linear meter - 4 rollers wire feed continuously adjustable - MIG - MAG hose package water-cooled approx. 4 linear meters - ground cable - pressure reducer - mobile base frame - connection 400 V / 6.6 A / 8.7 kVA space requirement approx. W 650 x H 900 + 450 x D 1100 mm - weight approx. 200 kg

Condition: excellent (used), I sell plasma cutter hypertherm powermax 800 d very good condition. /////Price listed for 1 pc ///// Plasma cutter Hypertherm Powermax 800 Ksdpoulc Ixofx Aa Esdp Plasma cutter description The Powermax800 plasma cutting system uses an inverter power supply to provide a smooth DC output voltage for superior cutting and gouging of mild steel, stainless steel, aluminum and other metals. The Powermax800's power supply provides a constant output current that varies from 20 to 50 amps, providing optimal performance for all metal thicknesses up to 1/2 inch (12 mm). At 50 amps, the Powermax800 can cut metals up to 3/4 inch (20 mm) thick and cut metals up to 1 inch (25 mm) thick.

Year of construction: 1988, condition: good (used), A complete Atlas Copco air compressor including Donaldson Ultra Filter and a Tank in good working condition Kodshpx U Aopfx Aa Eedp

Year of construction: 1993, condition: ready for operation (used), machine/vehicle number: Seriennummer: 9302394, CNC-Control HATASTAR 2000 The press capacity is 500 t or 5000 kN In addition to the machine tools are available Switch Cabinet left X1- + R-/ X2- + R-Axe on round guide Y1- + Y2-Axe hydraulic Upper tool clamping pneumatic sheet metal trace-device Second tow-hands Operation universal matrice 100x100x5'100 mm knife 280 x 5'100 mm Kdjdpfx Aajd Egc Ao Ejp Matrices-central plate, b = 111 mm