Pneumatic press

TOX PCG 075.220.A.001

Condition: good (used), Make: OMERA Rodpfx Askvnumob Ier Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Rodpfx Abjg U Utvo Isr Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Year of construction: 2022, condition: like new (used), Piovan dryer SIST. DEUM. GMP150+2xPTUN2000 RAFFRED. GMP150+2xPTUN2000 COOLING SYSTEM As good as new, unused Rjdpsvhb S Ssfx Ab Ior The PTUN... module is a single drying unit for plastic material. The machine consists of the following parts. - Hopper. - Holding frame. - Heating chamber. - Connection lines. - Air control valves.

Year of construction: 1981, condition: good (used), machine/vehicle number: 3626, OFFER 21448 Technical data: - max. working width 2540 mm - max. cutting capacity St 40 4 mm - mot. cutting angle adjustment - cutting gap adjustment by scaled adjusting screws - number of hydraulic hold-downs 14 pcs. - motorized backgauge with positioning stop 10 - 1000 mm - Stroke rate depending on cutting angle and cutting length 23 per/min Redpfjhhc Ixox Ab Isr - hydraulic drive 400 V / 7,5 kW - table height 1030 mm - space requirement approx. W 2500 x H 1630 x D 2150 mm - weight approx. 3600 kg - with: - pneum. supported sheet metal support - front angle stop + support arms - Electronic cutting depth adjustment - cutting line illumination - E-foot switch

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm Rodpohlnzkjfx Ab Ior column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Year of construction: 1965, condition: used, machine/vehicle number: 4447, working width: 2500 mm metal sheet thickness: 4 mm Rodpfxob H Ibue Ab Isr throat: 70 mm rear stop: 520 mm power: 380 V, 6,3 kW space needed: 3200 x 2300 x 1270 mm weight: 4600 kg

Condition: used, Year of construction: 2009, pressure 40 t stroke 4 - 100 mm no. of strokes 130 /min throat 230 mm dayligth 475 mm table surface area 650 x 460 mm hole in the table 205 x 165 mm table height over floor 710 - 950 mm table adjustable 240 mm ram surface 435 x 240 mm ram adjustment 85 mm power requirement 5,0 kW Weight 2,6 t dimensions of the machine ca. 1,2 x 1,7 x 2,3 m x m x m permitted for manual loading according to the CE-norm Rjdpfx Asvzxpnjb Isr with motor, pneumatic hydraulic clutch/brake combination, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, motoric centralized lubrication, adjustable table, two-hand and foot operation

Condition: used, Year of construction: 1978, sheet width 3100 mm plate thickness 2 mm rear stop 1000 mm cutting angle 1°06 ° no. of strokes 45 Hub/min total power requirement 3,0 kW dimensions of the machine ca. 3600 x 2200 x 1600 mm weight 4500 kg Equipment: - Electric motorized backgauge - With digital ELGO position display - Manual cutting gap adjustment - 1x side stop with mm scale - 2x support arms - 1x freely movable double foot switch Rsdpsuagxpofx Ab Ijr - Front finger guard Special accessories included: - Pneumatic sheet metal holding device for thin sheet metal cuts

Condition: as good as new (ex-display), Year of construction: 2008, machine/vehicle number: LSP 100T, Productions-Hydraulic press with H-column 100t Rsdpog Rn Efsfx Ab Isr with guidance Manufacturer: Stenhoj Denmark Year of construction: 2008 Pressure force max. 1,000 kN / 318bar Press cylinder, stroke length: 400mm Press table with T-slot 1,500x900mm above 1,500x1,050mm below Stand passage 1,700mm Condition as good as new, the machine was only used for test runs and has been in stock since then. All statements without guarantee. Without transport costs.

Condition: good (used), Used hydraulic shear brand SCHIAVI, mod. GH540A Useful cutting length mm 4040 Cutting thickness 5 mm Motorized rear register stroke mm 1000 Lateral recess 500 mm Min strokes 20-55 Cutting angle variation 0° 29" - 1° 14" Redpfx Absqfc Imo Ijr Manual blade gap adjustment Three-phase current 380V Main motor power Kw 9 Overall dimensions mm L 4570 mm x l 2310 mm x h 1705 mm Approximate weight Kg 11000 Good condition viewable