Suction

TEKA StrongMaster IFA

Year of construction: 2015, condition: used, Dimensions (L/W/H) 700x655x1400 mm Filter capacity / m² Number of filters 1 St. Number of dust containers 1 St. Lhodsgr Rkxepfx Ag Rep Weight 140 kg

Condition: new, GRATMAXX Bürstentgratmaschine The machine is suitable for the deburring of edges on: Round tubes, square tube, rectangular tube, full materials, profiles of all kinds. Materials: Steel non-ferrous metals, plastics, hard or soft. Work flow: After setting the workpiece support and dern side stops the Ridge-workpiece is easily kept on the brush rotating around its own axis, without rotating the workpiece, this movement is also the brush. The workpiece material, the Ridge strength, as well as the desired rounding of the edges determine the pressure and the duration of contact seconds, usually around 1-5. Technical data: Material: Steel, stainless steel and non-ferrous metals (engine speeds 700-1,900 rpm, infinitely variable) Min. workpiece-Ø: 5 mm Maximum work piece-Ø: 100 mm (150 mm) Brush dimensions: 2 piece Ø300 (250) x 50 or 3 piece Ø 300 (250) x 35 Lhodpsd Hmnfjfx Ag Rjp Power: 3,0 KW Power: 3.5 KW Operating voltage: 3 ~, 400Volt, 50 Hz Rated current: 8A Back-up fuse: max 16A Control voltage: 24V/DC Width: approx. 500 mm + Handwheel 74 mm, + dust spout 130 mm Altitude: 1.382 mm Working height: approx. 1.080 mm Depth: 1,209 mm Weight: 310 kg Sound pressure level: At speed 700 rpm 64 dB(A) at a speed 1500 rpm 74 dB(A), when machining a workpiece with maximum speed of 82 dB(A) Scope of delivery: Rotary head Bürstentgratmaschine GratMaxx with power socket without cable Workpiece support table with adjustable angle stop and

Year of construction: 2010, condition: ready for operation (used), Volume flow: 1000m³/h, max. depression: 10,000Pa, motor power: 5.5kW, weight: 350kg. Lhedpfx Agshz Dx Se Rop

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, machine/vehicle number: 306 431, type of input current: three-phase, total height: 2,165 mm, total width: 1,800 mm, total length: 3,000 mm, overall weight: 1,250 kg, input voltage: 400 V, type of cooling: air, Equipment: cabin, Machine year 2021, bought used December 2022, checked / repaired / adjusted by specialist company in April 2023. Only run for a few hours in trial operation since then. Lhsdpfx Ageulw E So Rjp

Condition: good (used), Year of construction: 1995, Offer 24315 Technical data: - Sanding belt dimensions 2000 x 100 mm - Surface sanding opening 400 x 100 mm - Support vice - angle adjustable 90° - 30 ° - Support fine adjustment via hand wheels - Sanding belt speed 30 m/sec. - Contact wheel / sanding roll Ø 42 mm - Drive 400 V / 2880 rpm / 3 kW - Space requirement approx. W 700 x H approx. 1200 x D 1200 mm - Weight approx. 225 kg - 10 contact grinding rollers approx. Ø 10 + 18 + 22 + 24 mm Lsdpfxet Stfho Ag Rjhp - 28 + 33 + 36 + 48 + 60 + 68 mm

Condition: new, 1860 m³/h Pressung 2.900 Pa 1,1 kW filter surface area 10 m² 72 dB(A) 400/50 V/Hz 665 x 1100 x 1495 mm 200 kg - Hose arm 3 m, joints inside - Filter cartridge: dust class M - Pre-filter: baffle plate - Current type: 3Ph+N+PE The filter system Lsdpehp S Trjfx Ag Rshp ----- The mobile filter system of the Cartmaster IFA type is thanks to the automatic Cleaning particularly suitable for welding work with unalloyed and alloyed steels, galvanized material and aluminum with heavy smoke development. It corresponds to the safety requirements for devices Welding fume class "W3" (high-alloy steels with alloy components > 30% Nickel-based alloy).If used as intended, the system can be used for the Recirculation mode used because the requirements for the Exceptions according to TRGS 560 are fulfilled. That special developed, dirt-dependent cleaning system ensures a good cleaning behavior of the filter cartridge, so that an optimal suction performance is guaranteed throughout the operation. The cleaned particles fall into a dust collection drawer from which they can then be disposed of. The powerful spiral fan ensures even with saturated Filter cartridges for a high volume flow. The filter media ----- A baffle serves as a pre-separator for coarse particles. The filter cartridge installed below (dust class M, degree of separation > 99%) filters the finest smoke and dust particles. The cartridge is factory coated which increases the service life. The extraction arm ----- The extraction arm can be moved with the 3 internal joints Position spring support slightly and is in the set position cantilevered. A throttle flap integrated in the extraction hood enables the Flow rate setting.

Condition: new, - Capacity 100 tons - Cylinder stroke 400 mm - working width 1500 mm - Cylinder is movable - Electrically or manually operated - Pressure indicator - Emergency stop Lhsdpoilvb Nofx Ag Rop - 400V

Condition: used, Year of construction: 1990, machine/vehicle number: 2316-3, Lg.no. 10622 Technical data: - Drilling capacity into solid steel ST 60 28 mm - Drilling capacity GG 25 40 mm - Thread cutting ST 60 M 30 - Thread cutting GG 25 M 40 - Drill spindle holder MK 3 - Spindle diameter 50 mm - Quill stroke 150 mm Lhjdpfsu Et Nbsx Ag Rjp - 18 drilling spindle speeds 45 - 2240 rpm - 4 drilling feeds 0.1 - 0.45 mm - min. / max. distance spindle - table 300 / 700 mm - Drilling radius min / max 305 / 1005 mm - Table height 820 mm - Table size 1200 x 600 mm - Drive 400 V / 6 kW - Space requirement approx. W 1300 x H 2800 x D 2300 mm - Weight approx. 1500 kg - with: - Thread cutting device - hydr. columns + boom clamping - Coolant device - Vertical T-slots on the left side of the machine

Condition: reconditioned (used), Year of construction: 2013, functionality: fully functional, 1 cloos welding robot QRC 300 ( year 2022 only 1258 hours) incl. control QC 2 ( year 2020, new PC 2022), teach pendant incl. cable Gasnozzle sensing, point editor Pedastal for robot Cloos welding machine Qineo Puls 350 (350 A pulsed arc machine), wire drive, torch, torch hose package, connection hose package, mech. torch cleaning 2 stations turning table incl. 2 turning devices QR-WP-TC 1,5 kN load capacity/station 150 kg, swing radius 400 mm, 1 light beam, 1 start stop box, 1 safety wall on turning table 1 safety switches for service door incl door Lhodpfxsiyp Nao Ag Rjp Base frame between robot and workpiecemanipulator delivery time: about 8 weeks. Subject to prior sale.

Condition: good (used), Year of construction: 1984, machine/vehicle number: 332, Offer 24130 Technical data: - Drilling capacity into solid steel ST 60 32 mm Lhodpfxotxzrwe Ag Rjp - Drilling capacity GG 25 40 mm - Thread cutting ST 60 M 27 - Drill spindle holder MK 4 - Quill stroke 150 mm - 12 drill spindle speeds 102 - 2000 rpm - 3 drilling feeds 0.1 - 0.3 mm - min. / max. distance spindle - table 310 / 610 mm - Drilling radius min / max 380 / 1200 mm - Table height 720 mm - Table size 1200 x 500 mm - Drive 400 V / 2.0 / 2.4 kW - Space requirement approx. W 1200 x H 2800 x D 2300 mm - Weight approx. 1500 kg - with: - thread cutting device - hydr. columns + boom clamping - Coolant device - Vertical T-slots on the rear side of the machine