Clutch-brake press КD2128 STANKOIMPORT

STANKOIMPORT KD2124, KD2128, H3222A

Condition: good (used), Make: OMERA Type: R4 / 12-2 Year: 1976 Table length : 1900 Table width : 1000 Steady arm throath HOR : 670 Steady arm throath VER: 940 Stroke cylinder : 350 Column diameter : 200 Specifications Metric US Standard There are no specifications for this machine (yet). Dimensions (Estimate) Length 3000 mm Width 2200 mm Height Gbodpfx Ajkvnumjcwok 2500 mm Weight 2800 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: as good as new (ex-display), Year of construction: 2021, machine/vehicle number: 06 61 218, Comm. no.: Lg 32821 Single side decoiler BBT ABH 2000/400 exhibition machine, unused machine no.: 06 62 218 year of manufacture: 2021 Technical data load capacity approx. max. 2.000 kg strip width max. 400 mm Coil inner diameter approx. 450 to 520 mm Coil outer diameter max. 1,500 mm Unwinding speed approx. 2 to 15 min.-1 With adjustable drive and loop control via ultrasonic sensor (analog). Drive by frequency-controlled three-phase geared motor. Spreading of the support segments manually by means of hand crank via joints Number of supporting segments 3 Coil side guide via strong limiting arms, clampable. Reel stand in strong box construction as welded design. construction. Additional equipment: Shutdown "belt loop too small" by antenna switch, Gjdpfx Acsg U Utvjwobk attached to the column of the bottom housing of the loop control. Infinitely adjustable in height. Tape side guide at the bottom housing of the loop control, by means of lateral guide rods. The passage width is continuously adjustable.

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load Gbjdpfehlnzkox Acwok - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: used, Year of construction: 2008, turning diameter 1000 mm swing diameter 1250 mm Gbsdpfjw Rgcfsx Acwok turning height 500 mm control Siemens Sinumerik 840 D Workpiece spindle flange diameter 520 mm work piece spindle speed range 0-440 U/min total power requirement 75 kW weight of the machine ca. 25 t dimensions of the machine ca. 5100 x 3034 x 4500 mm With grinding spindle Table travel: - Z1/Z2 axis 1000 mm, - X1/X2 axis approx. 1300 mm Table speed continuously adjustable: - Z axis 0–30 m/min, - X axis 0–50 m/min - Feed speed continuously adjustable 0.01–15 mm/min - Feed dependent on stroke 0.0005–0.1 mm - Workpiece spindle positioning C axis Equipment/accessories: - Grinding spindle - Kaiser dresser - Tool measuring probe - Filter system - With flushing nozzle connections - 2 Capto holders - 1 set of jaws for chuck - technical documentation

Condition: used, Year of construction: 1987, pressure / t stroke / mm table-size / mm weight of the machine ca. 65000 kg Make: Shepherd Type: SVRM 4-roller bending machine: Year of construction: 1986 Working width: 3000cm Smallest pipe diameter with 600 mm roller: Ø 720 mm Smallest tube diameter with 360 mm roller: Ø 460 mm Sheet thickness up to (depending on the material): 50 mm Material SA- 738 B Working width: 2500 mm Material SA- 738 B Material thickness: 35 mm conical bending: Except for the top roller, all rollers can be moved in an inclined position for conical bending. The roller positions can be read on display instruments. For semi-automatic or fully automatic operation of the machine, the bearing jewels of the rollers are equipped with scale bars and slide cams for limit switch Gbsdpfsuddcajx Acwjk actuation. This allows the rollers to return to the same set position over and over again, giving a very high level of uniformity in the shot wefts being bent.

Condition: used, Down table size: 1120x1250mm Technical characteristics: *UP DOWN STROKE 1000 mms *FORWARD BACKWARD STROKE 1200 mms Gbedpfxe Dv Nxo Acwok *LEFT RIGHT STROKE 1000 mms

Condition: good (used), Year of construction: 2006, Brand: GEMINIS Model: GHT4 G2 700x 2000 Cnc: FANUC 21 TB Distance between centers: 2000 mm Ø Swing over bed : 720 mm Gsdpfx Acoxdub Iewsbk Ø Over carriage: 470 mm Spindle diameter : 104 mm Maximum piece weight between points : 2.560 kg Spindle nose: DIN 55027-11 Spindle speed: 0-1600 m/min Total power : 28 kw

Condition: used, Year of construction: 2005, functionality: fully functional, measuring range X-axis: 700 mm, measuring range Y-axis: 1,000 mm, measuring range Z-axis: 600 mm, Equipment: type plate available, Mitutoyo Crysta Apex C7106 coordinate measuring machine Temperature compensation on all axes Active vibration isolation system from BILZ X-axis measuring range = 700 mm Y-axis measuring range = 1000 mm Z-axis measuring range = 600 mm Measurement uncertainty = 1.9 + 3L/1000 (µm) Renishaw PH10MQ probe head Renishaw SCR200 interchangeable rack Renishaw TP200 sensor Renishaw TP200 modules = 6 units MCosmos measuring software Gbjdpfewhb A Nsx Acwek WIN10 PC system, 27" monitor Reference sphere / calibration sphere Optional software upgrade Optional hardware upgrade Full service available upon request

Condition: ready for operation (used), Year of construction: 2005, turning diameter over cross slide: 570 mm, turning length: 2,000 mm, spindle bore: 62 mm, spindle speed (max.): 2,500 rpm, spindle speed (min.): 3 rpm, workpiece weight (max.): 2,000 kg, Equipment: rotational speed infinitely variable, The VDF 560 DUS are the most popular teach-in lathes from VDF Boehringer in terms of turning diameter. With a standard chuck size of 315 mm or more, these machines offer optimal machining efficiency for the production of single parts and small series. This machine is currently on display in our showroom; an on-site inspection is possible! Scope of delivery: Includes drawer cabinet with various tools and Multifix holders. Specifications Manufacturer: VDF Boehringer Model: DUS 560 TI Year: 2005 Condition: Used Gbjdpfowv S Rtex Acwok Stock number: 00164 Maximum turning diameter: 570 mm Maximum turning length: 3000 mm Spindle bore: 62 mm Speed (min-max): 3 - 2500 rpm Spindle power: 19 kW Spindle mount: DIN 55 027 Gr. 8 Tool turret: Multifix Turret positions: 2 Tailstock taper: MK5 CNC control brand/type: Heidenhain Manual Plus 4110

Condition: used, Year of construction: 2000, functionality: fully functional, grinding width: 2,600 mm, workpiece weight (max.): 35,000 kg, grinding length: 12,000 mm, distance between stands: 2,800 mm, grinding height: 1,600 mm, Portal Grinding Machine 12x2.6m Brand: GIORIA Gsdpfx Aowql H Docwobk Year:2000 Controller: Siemens 840C (twin operator panel with HPU) Table: 12.500 x 2.600mm Heigh feed: 1.600mm Hydrostatic table Including grinding disc etc.