Horizontal block press

Schweizer Fabrikat BP 5000

Condition: good (used), Auriol M500VBEX cooking kettle Serial: 3429 Hedpfx Afjnbd S Tj Ssu Stainless, 500l capacity, steam jacketed, emulsifier with bottom mounted motor, emulsifier diameter 120mm, variable speed, auto tilt to discharge, on load cells, 3Ph

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Hsdpjua Tbwjfx Af Ssu Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Description of action: The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order.

Condition: like new (used), Year of construction: 2011, OMET Varyflex VF1 Year of manufacture: 2011 Web width: 850 mm Printing process: Flexo + Rotogravure combination line Condition: Used – very good condition Location: Europe _____ Machine Configuration • 8 x UV flexo printing units (equipped with new UV lamps, LED-ready) • All flexo units in ATEX execution (suitable for solvent-based inks) • 1 x rotogravure unit (compatible with solvent- and water-based inks) • 1 x die-cutting unit (530 mm) Hodpfx Aeyyn Hfof Seu • In-line slitting system • Double turret rewinder • Turn bar (web turning system) • Hot air dryer on first printing unit • Cold seal trolley (movable) • Cold foil unit (cassette type, positionable on any unit) _____ Equipment & Tooling • Extensive anilox roller package • Sleeve system (well maintained) • Tooling in very good condition Optional (available upon request): • Omet plate mounter • Bimec slitter rewinder 1200 mm (almost new condition) _____ Technical Highlights & Advantages The OMET Varyflex VF1 is a highly versatile production platform designed for both label and flexible packaging applications. Key advantages: • Wide web format (850 mm) – ideal for high-volume production • Hybrid configuration (flexo + rotogravure) for maximum flexibility • ATEX design allows use of solvent-based inks • LED-ready UV system for future energy efficiency upgrades • Modular configuration with movable units (cold foil/cold seal) • Excellent condition with recently updated electronics (PLC, drives, control cabinets) • Proven application: previously used for polyethylene-coated materials (80–90 g/m²), ensuring reliability in demanding environments This machine offers an outstanding balance between performance and flexibility.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, total length: 4,500 mm, total width: 3,375 mm, WEIMA Crusher Series HWV 3000 (37 kW) and the Single-Shaft Shredder WL12 (30 kW) Ideal for pre-shredding wood waste such as pallets, followed by metal separation and secondary shredding. Hsdpjy Ubvpofx Af Seu Advantages: Two-stage process: Pre- and post-shredding for maximum efficiency. Versatile use: Wood chips for heating systems or briquetting presses. Low-noise operation Technical details – HWV 3000: - Power: 37 kW - Dimensions (hopper): 3375 mm width x 1630 mm height - Cutting knives: 58 knives in two rows Technical details – WL12/30: - Power: 30 kW - Shaft diameter: 368 mm - Screen: 15/20 mm Applications - Wood waste processing and recycling - Energy generation through wood chips or briquetting

Condition: ready for operation (used), Year of construction: 2013, operating hours: 5,000 h, functionality: fully functional, machine/vehicle number: 01113, total width: 2,180 mm, total length: 12,200 mm, bale length: 500 mm, bale height: 400 mm, pressing force: 350 t, overall weight: 34,000 kg, Ecotecnica shear baler mod. 2535, year 2013, with approximately 5,000 operating hours, in good working condition and complete with documentation. Machine suitable for compressing and shearing ferrous scrap, including sections, sheet metal, and mixed scrap. Technical data: Shear force: 350 tons Operating hours: 5,000 Compression box length: 5.0 m Box width with wings open: 1.70 m Bale size: 500 x 400 mm Total length: 12.20 m Width: 2.18 m Weight: 34,000 kg Equipment: Iveco diesel engine, 172 HP Radio remote control Complete documentation Machine is fully functional and ready to use. Hsdsy Ibw Tepfx Af Sou Inspection and testing possible.

Condition: excellent (used), functionality: fully functional, Trendelkamp Separation Table / Vibrating Sieve Machine – 3 Fractions For sale is a Trendelkamp separation table, model TK-K60/85, weight 200 kg. This machine is designed for the precise separation of bulk materials into three fractions by means of vibration and screening. Technical data: • Manufacturer: Trendelkamp Stahl- und Maschinenbau GmbH + Co. KG • Model: TK-K60/85 • Weight: approx. 200 kg • 3-fraction separation • Driven by electric motor with unbalance drive • Robust steel construction, screen decks made of stainless steel • Screens can be easily replaced upon request (different mesh sizes available) Areas of application: Hjdpfew Ip Dtox Af Sju Ideal for plastic granulate, recycling materials, pellets, bulk materials, and other applications requiring separation into three size classes. The machine is immediately ready for use and in good condition.

Condition: good (used), Auriol cooking kettle Stainless, 400l capacity, steam jacketed, emulsifier with bottom mounted motor, emulsifier diameter 120mm, variable speed, auto tilt to discharge, on load cells, 3Ph Hodpfsnbd Ryox Af Sou

Condition: ready for operation (used), A 4-color central cylinder printing system WDB Systemtechnik is available. Printing units: 4, ink type: UV, max. material width: 650mm, max. printing width: 600mm, printing length range: 300mm–800mm, max. printing speed: 250m/min, material types: PET/OPP/aluminum/laminate/composite materials, material thickness range: 20µm–150µm, max. unwind and rewind roll diameter: 1000mm, operating hours: 28h, printed length: approx. 57000m. System components: unwind and rewind unit, corona, UV dryer, drying channel, IR heater, cooling unit, and supply and exhaust air fan. Including lamination unit. Documentation available. An on-site inspection is possible. Hjdpfxoxmkcto Af Ssu

Condition: new, Year of construction: 2025, Turbo mill MTR-800 This turbo mill is designed for grinding, crushing, and granulating materials to improve the quality of final separation in subsequent recycling processes. Technical data: - Installed power – 75kW or 90kW - Chamber width – approx. 910mm Hedpfjv I S Ukex Af Seu - Chamber diameter – approx. 620mm - Number of abrasive knives – approx. 89 pcs. - Number of abrasive counterknives – 18 pcs. - Structure mounted on adjustable vibration isolators - Dimensions – 2200 x 1600 x 1550mm - Chamber opening via a manual hydraulic pump - Engine base with a rocker-type tensioner - Weight – approx. 1950kg - Discharge ends with an orifice of fi-150 - Electrical installation with inverter included in the price.

Year of construction: 2023, condition: new, The sieve machine is ideal in combination with a crusher and / or mill for the exact separation of bulk materials. Hjdpfx Afeh R Twbs Sju