SCHELLING FH4 430 + BARBARIC LVC STORAGE

SCHELLING + BARBARIC FH 4 430 + LCV

Condition: used, Year of construction: 2016, Angular panel saw with automatic pre-loading and twin pusher system for optimised cutting Osi Plus Numerical Control Os Labelling labelling machine with on-board graphic labelling with part drawings Label printing management software Optiplanning Cutting Optimizer Cutting length mm 4500 Cutting width mm 2200 Blade projection 95 mm Motorized rollers for lateral loading on lifting table 4500 x 2200 mm. The translation speed is 10.8 m\min (50hz) - 13.1 m\min (60hz) Automatic recognition of the lost panel (martyr panel) based on the thickness specified in the machine data Low battery stop Automatic side loading buffer. Includes: perimeter nets, double photocell, push-button panel, predisposition electric for the two motorized pre-rollers and the amplification of 4 rollers in place of the fork passages in the pre- intermediate roller conveyor Pre-loading side roller conveyor dim 3800 x 2200 mm with motorized rollers (height from the ground 325 mm) Inertial conveyor for conveying longitudinal trimmings for angular systems 4500 mm (total length 7295 mm) 3000 mm extension to the inertial conveyor to also convey transverse trimmings Long chute for manual conveying of cross-cut trimmings to the centralized inertial conveyor 2050 x 850 mm air curtain discharge table with wheels at the front Air generator up to 6 floors with air curtain MULTIPUSHER 2.4 system with automatic lubrication Additional mobile lateral aligner on the transverse plane. The presence of this device allows to reduce from 1830 to 1220 mm is the minimum length of the panels that must be sent for cross-sectioning. Automatic blade shaft bending detection device for angular systems (longitudinal and transversal) consisting of a sensor that detects the deflection directly on the blade shaft and a device that detects the revolutions blade directly on the spindle. Remote cycle start button panel Automatic panel loading via rear lifting table Automatic double aligner with pneumatic cylinders Hnodpfouc Idxox Agmsn Additional movable lateral aligner on the transverse plane Main blade, max diameter mm, KW 15 Scoring blade, max diameter mm, KW 2.2 Blade carriage speed 1-140 m/min. – BRUSHLESS motors Longitudinal pusher carriage speed 90 m/min. Cross pusher carriage speed 135 m/min. Double pusher carriage with 6 grippers on the longitudinal carriage + 10 grippers on the transverse carriage (8 fixed grippers + 2 on the multi-push system) Cutting system for thin panels

Condition: excellent (used), Year of construction: 2003, machine/vehicle number: 0-241-06-5232, functionality: fully functional, operating hours: 12,608 h, cutting height (max.): 125 mm, cutting width (max.): 2,200 mm, cutting length (max.): 4,300 mm, Panel Saw Holzma HKL11/43/22 Max. cutting width: 4300 mm Max. cutting length: 2200 mm Max. cutting height: 125 mm Hnjdpfjxfvp Aox Agmsn The saw is in continuous operation, so viewing during operation is possible. The machine will be available from 02/03/2026.

Condition: excellent (used), Panel loading 15 beats per minute, complete with motorized roller conveyors Hodpfehv Sttex Agmsnn Loader

Condition: used, Year of construction: 2012, operating hours: 9,974 h, total height: 2,700 mm, total length: 7,700 mm, total width: 2,420 mm, Empty weight: 7.390 kg CNC machining centre SCM Morbidelli M-600 5-axis machine Year of construction 2012 Machine no. AA2/002032 Working distance X-axis 5020 mm Working distance Y-axis 1680 mm Working distance Z-axis 250 mm Tool positions 36 Vertical drilling spindles 24  Hodpfswnhccjx Agmjnn Software SCM XILOG MAESTRO SCM PRISMA K SCM TTS system Milling spindle liquid-cooled SCM TecPad MORBIDELLI TV Matic SCM PRO-SPACE SCM RAPID 12 SCM RAPID 24 Including vacuum pump Capacity 250 m3/h Disassembled for transport Weight 7450kg - Details: - └ Description: Machine gives malfunction spindle - Year: 2012 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AA2/002032 - Operating hours: 9974 - Number of milling spindles [pcs.]: 1 - └ Milling spindle 1: - - Number of controlled axes [pcs.]: 5 - Type milling table: Beam table - Drilling unit present: Yes - └ Horizontal drill spindles [pcs.]: 6 - └ Vertical drilling spindles [pcs.]: 24 - Saw unit present: Yes - Tool changer positions [pcs.]: 36 - System/software: SCM Maestro - Vacuum pump present: Yes - └ Number [pcs.]: 1 - └ Brand: Becker - └ Capacity [m³/h]: 250 - CNC options: Offcut conveyor - Working range X [mm]: 5020 - Working range Y [mm]: 1680 - Z-axis working range [mm]: 250 - Transport dimensions: 7700mm x 2420mm x 2700mm (l x w x h) - Transport weight [kg]: 7390kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: ready for operation (used), Year of construction: 2007, controller model: CADmatic 4 - Professional, This HOLZMA HPP 380 panel saw was manufactured in 2007. It features a robust steel saw carriage, main and pre-cut saws, and a patented Central Angle Return Device that reduces cycle time by up to 25%. The machine is equipped with a Power Control CADmatic 4 system, ensuring precise and efficient operation. The saw blade projection is 95 mm, and it operates with a main saw motor of 18.0 kW. For more information about this panel saw, please reach out to us. Additional equipment • Air cushion table with roller element 2160 x 650 mm: 4 pieces • Central blower: 1 piece Machine Benefits Qualitative Machine Benefits • Ce-certified, gs-certified, fph wood dust certified • Division: 75/275/475/1050/1850/2650/3450 mm measured from the angle rule to the center of the clamping collet Hodpfxoyaiiyj Agmsnn • 2 additional two-fingered clamping collets possible • 4 manual trimming rakes at clamping collets • 1 additional one-fingered clamping collet possible • Jet spacing of air cushion tables: 70 x 70 mm Technical Machine Benefits • Pre-cut saw motor: 2. 2 kw • Operating voltage: 400 v / 50 hz • Electrical connection value at hs motor: 18. 0 kw = 24 kw, 21. 0 kw = 27 kw • Positioning accuracy: +/- 0. 1 mm/m • Surface-friendly material transport, lifetime positioning accuracy, no lubrication required, high program slider speed, maintenance-free, full stability of the steel table maintained, easy, cost-effective replacement of phenolic resin plates, minimal wear of the cylinders, uniform pressure application, minimal cutting = scratch cut, significant cycle time savings, top cutting quality, minimal setup times, reduction of cycle time, pressure strength electrically adjustable • Cutting length: 4300 mm • Cutting width (program slider travel): 4250 mm • Roller track (element 10-track): 1 piece • Roller track (element 2-track): 5 pieces • Clamping collets: 7 pieces (first 3 pieces two-fingered, all others one-fingered) Extra Information Machine still under power

Condition: excellent (used), Year of construction: 2009, machine/vehicle number: 241.125, functionality: fully functional, Horizontal Beamsaw of the manufacturer Schelling, designed for cutting wood-based material Hnsdpox Ebzdsfx Agmon HPO – cutting optimization program Saw blade projection: max. 95 mm Saw carriage feed up to 120 m/min Cutting lengths: Model FH 4 430 - 4.300 mm Can be inspected in working condition until beginning 2026. (dismantling planned) Maximum Saw blade Diameter - 350 mm Projection - 95 mm Clamp opening 90 mm Power Saw motor - 15 kW Scorer Diameter 300 mm Feed rate forward up to 80 m/min reverse 80 m/min Saw feed rate forward up to 120 m/min reverse 120 m/min

Condition: excellent (used), Horizontal Panel Beam Saw - With rear lifting table Numerical Control MCS Evolution Software SIEMENS WinAC RTX Hnsdpfx Ast Ah Nijgmen Outside Roller table for pre-loading (mm 5600 x 2200) + Pre-Loading Buffer Lifting table (mm) 4300 x 2200 Turning device (rotating unit) at 90° No. 2 Rear pushers (one with clamps / grippers) Twin Pusher - DUPLUS2 No. 12 clamps / grippers Max. cutting width (mm) 4300 Useful stroke of the pushing system (mm) 4300 Max blade projection (mm) 145 Max clamps opening (mm) 150 Scoring Unit (max saw diameter / power) 200 mm Main Sawing Unit (max saw diameter / power) 480 mm - Kw 27 Adjustable speed of the saw carriage (m/min) 6 - 150 Front supporting tables with Air blowing system (N.) 4 Total power (Kw) 42 (ca.) OPTIONAL: Optimisation software: HPO

Condition: excellent (used), Horizontal Panel Beam Saw - With rear lifting table Numerical Control MCS Evolution Software Lifting table (mm) 4300 x 2200 No. 2 Rear pushers (one with clamps / grippers) No. 8 clamps / grippers Max. cutting width (mm) 4200 Useful stroke of the pushing system (mm) 4200 Hjdpfx Agoq Rffijmenn Max blade projection (mm) 135 Max clamps opening (mm) 125 Scoring Unit (max saw diameter / power) 200 mm Main Sawing Unit (max saw diameter / power) 460 mm - Kw 21 Adjustable speed of the saw carriage (m/min) 6 - 150 Front Turning table (rotating at 90°) with air blowing system (mm 2100 x 4100) Total power (Kw) 36 (ca.)

Condition: new, Product description: Hnedpfxjdy Ewls Agmon I-Beam Type Hanger Conveyors Conveyor Systems are one of the most important parts of the lines used in automatic coating plants. Our conveyor systems, which carries the parts to be painted in meters per day and kilometers per year, play an important role. Heavy parts to be coated are carried by webb conveyors which perform for long years with their long lasting bearings and steel cast chains. It has a wide carrying capacity range starting from 120 kg to 2 tons. • Operating principle of this type of conveyors is based on transferring suspended materials by chains and trolleys moving on a NPI profile by the help of a drive unit. • WEBB type conveyor chains are made of nodular cast iron or forged steel and subjected to heat treatment afterwards. • Special roller bearings used on trolleys are capable of operating at 200 °C. Greasers placed on trolley bodies provide lubrication for the system. • The drive system can be built based on either the caterpillar system or the gearwheel system, with safety switches and moving trolleys. • Conveyor speed can be easily adjusted by use of a frequency controller. • Chain tensioning system consists of skids and springs. Rollers and support wheels are used for band turns.

Condition: good (used), Production line consisting of: - BACCI FC 8 - BACCI DOUBLE JET - KUKA robots BACCI FC 8 The automatic copying-shaping-sanding machine executes milling and sanding operations on components of chairs, tables, armchairs, sofas, beds, furniture, frames, with the best finish and highest output. Max working length: 4000mm Max working height: 180mm Max working width: 500mm Max working width with round end: 350mm Max speed working table: 15m/min Max table return speed: 50-100m/min BACCI DOUBLE JET DOUBLE-JET is double machining centre with 6+6 interpolated CN axis, equiped with hopperfeeder system for automatic loading/unloading of the pieces. Hnedpfst Txfpex Agmen