Cross cut saw

SALVAMAC Legend 600

Condition: new, Year of construction: 2025, functionality: fully functional, saw blade diameter: 600 mm, cutting height (max.): 160 mm, cutting width (max.): 610 mm, power: 0.01 kW (0.01 HP), Extreme robustness and maximum power! The Legend_600 has a completely painted, thick and reinforced steel structure. The blade with a diameter of 600 mm, the power of 9.2 kW and the rotation speed of 2750 rpm make it the ideal machine for those who work with wood up to a maximum of 150 mm thick and 610 mm wide. Ndedpfxofcdnlj Abgod

Condition: new, Year of construction: 2025, Cutting height at 90°: 170 mm Cutting length: 430 mm miter range horizontal: 45°-90°-25° Miter range vertical: 60° - 90° - 30° Pivot adjustment with crank: yes roller conveyor / support table: yes Saw blade diameter: 420 mm Speed: 2800rpm Engine power: 3 kW Motor brake: yes Suction connection: 100mm Length roller conveyor: 2 x 1500 mm Machine length: 4000 mm Machine width: 1250 mm Machine height: 1550 mm Nodeizkhvopfx Abgodd Weight:

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm Ndodjd Iipmepfx Abgod 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens

Condition: used, Year of construction: 2007, RA1784 Pallet rack system Galler OMEGA used 16600 x 5400 x 1350 mm Installation in a hall Shelf height: 5.400 mm shelf depth: 1.350 mm clear field width: 3.200 mm stored goods: pallets with stored goods Deep storage: 1,350 mm Storage arrangement: 1. stored goods on the floor 2. to 5 stored goods on pairs of tie bars, Shelf load on pair of spars at daylight Field width of 3.200 mm and : 2.100 kg Nedpfx Aok Abbbebgedd shelf height 1.500 mm Field load: 8.4 to. at 1,500 mm buckling length (min. 4 fields) →Alle Loads are understood to be with evenly distributed load. Painting: Upright frame: Sendzimier galvanized Support beam: RAL 7035 light grey WITH RUST SPOTS (SUPERFICIAL) Installation: 1 pc. one-sided shelf axis, standing on a hall wall 5 x 3,300 + 100 = total length 16,600 mm consisting of: 6 pcs. stand frame Galler Omega screwed 5.400 x 1350 mm 40 pcs. carrier beam Galler Sigma 3.200 mm 80 pcs. safety pins Price net plus VAT from central warehouse Dr. Sonntag GmbH & Co KG, Würzburg Optional if required 2 pcs. ram protection corner used At the beginning or end and at passages to protect the shelf stem For individual, professional advice, simply contact us. Simply contact us by phone or e-mail. We will be happy to help you with the planning and implementation of your projects. We look forward to hearing from you. With kind regards Your team at Dr. Sonntag GmbH & Co. KG Your specialist and contact for intralogistics

Condition: new, Year of construction: 2024, Cutting capacity: 55x360, 80x340, 95x325, 125x295, 135x280 mm Minimum work piece thickness mm.10 Working table tilted 8° Cutting unit technical features: Pneumatic upstroke saw TR500 Motor power 10 HP (7,5 kW), Volt 400/50 Hz. TCT Blade dia.500 mm., F=30 Z=144 S=4,6 Cutting cycle speed: 4 seconds Push feed system technical features: PUSH FEED SYSTEM AVAILABLE LEFT AND RIGHT SIDE Feeding by rack and pinion system and brushless motor Positioning precision +/- 0,4 mm Strong infeed motor for a packet weight of 80 kgs Maximum push feed system speed 90 m/min Pneumatic rising of the pusher at the end of the cutting cycle and overhead returning. Data entry management: 12 inch TOUCH-SCREEN Controller (800x600 pixel) USB Port Ethernet Port LINUX Operating system Loading and save machine parameters via USB Port Cutting cycle (pattern) editing and entered directly on the controller Transfer of cutting lists created by PC via USB or Ethernet Port Working software: Manual input of loading board length Partial optimization without length reading of the board Cutting cycle with 3 optimization options (Maximum length, Sequence and Board sequence) N°1000 cutting lists made up of 11 sizes or one list of 10000 sizes in sequence Package "OPTI": automatic board length detection and full optimization. Piece length reading by photocell Cutting cycle: with 6 optimizing criteria: (Longest length, Sequence, Board sequence, Volume, Minimum waste and Priority length) Package "OPTI PLUS": total optimization with knots and defects removal (OPTION NOT INSTALLED ON THE MACHINE) Technical Description: Package "OPTI PLUS": for knots and defects removal Photocell for reading wood mapping knots and defects Marking with fluorescent chalks/crayon (Note Ð Can only be ordered in combination with ZA250) Ndsdpfxohw Ng Is Abged Pneumatic side clamp device

Condition: reconditioned (used), Year of construction: 2018, The SQUALO 420 multi-blade or multi-blade circular saw with double shaft is a technological machine, indispensable in a modern sawmill to optimize the production of sawn timber. Ideal for the production of strips, squares, sawn timber, profiles, edged boards, prisms, boards, elements for pallets. SPECIAL PRICE, OFFER OF THE MONTH Ndodpfxjhrdxio Abged UNBEATABLE PRICE

Condition: new, Equipment: lighting, Take your painting process to a new level - with mobile convenience. Mobile paint booths in container design for painting and coating various objects. They are specially designed for mobility so that they can be easily transported and set up on different construction sites. The booth is usually equipped with a ventilation system to ensure air quality, lighting and a filter system that prevents paint mist from escaping. Ndjdpfx Ajun Shgobgod The ventilation system ensures that the vapors and particles released during painting are kept inside the booth so that there is no danger to the environment. Mobile paint booths are a practical and flexible solution for companies that need an effective painting system that can be moved from one construction site to another at any time. Overview of the design and functions Our mobile 20-foot Sapi painting containers consist of a robust steel frame with welded wall and ceiling panels. Inside, we can add special equipment such as cranes or lifting devices. The floor is made of tear plate. There are ventilation grilles in both door leaves, which are fitted with fine-pored filter mats. One leaf is designed as an escape door for safety reasons and has a viewing window. It should also be mentioned that these are not simply converted shipping containers! We manufacture all our containers from scratch ourselves. We only use the most stable materials that meet the requirements and have also been tested and proven in terms of safety. Normal shipping containers would not meet the required safety standards. Paint extraction system in the mobile painting container The paint mist extraction wall for paint mist separation is located in front of the rear wall and is equipped with multi-layer filter mats. The extraction wall consists of a galvanized housing, edged with baffle plates including various suspension and fastening elements for the filter equipment. The powerful and EX-protected extraction fan with drive motor is installed on a console in the rear wall area on the outside of the container. Next-generation mobile spray booths: meeting EU requirements and advancing coating solutions The new generation of mobile spray booths must meet the highest EU requirements. The consideration of new paint systems such as hydro paints, polyurethane resins, epoxy-zinc dust or epoxy-iron-mica paints places high demands on existing paint booths. That is why we have developed a new and unique mobile paint booth for the next generation of coating solutions. An important criterion is the transportation of the workpieces for painting and for further processing steps. Do you need more information? Our engineers can offer expert advice and support. Whether paint mist dry separation or wet scrubbing, air humidification or air drying, condensation drying in a low-temperature process or hot air drying, whether pre-treatment of the workpieces by high-pressure washing with water flow in a circulation system or by compressed air blasting or wheel blasting technology.

Condition: used, Year of construction: 2014, Number of spindles 5 St. Working width 230 mm Working height 120 mm Length of the planing table 2500 mm Feed motor 4 kW Feed speed 5-30 m/min. Control Memory-Funktion Weinig Powermat 600 Compact ----- The machine will be cleaned and completely checked before delivery. Brief Summary: ----- - 5 spindles - Powerful motors - Left and upper spindles controlled for width and height Detailed Description: ----- Technical Specifications: Working width: 20-230 mm Working height: 10-120 mm Nedpfx Ajwzmu Robgodd Number of spindles: 5 1st spindle - bottom ----- Motor with brake: 7.5 kW Spindle diameter: 40 mm Speed: 6,000 rpm Tool travel radius: 125-145 mm Tool travel radius for rebate cutter: 130-160 mm Axis adjustment range: 5 mm Rebate device MarathonCoatin for table insert in front of the 1st lower tool holder Electronic digital display for wheel adjustment 2nd spindle - Right ----- Motor with brake: 11.0 kW Shared motor with left-hand tool holder Spindle diameter: 40 mm Speed: 6,000 rpm Tool cutting radius 40 mm below table level: 93 - 200 mm Tool cutting radius 55 mm below table level: 93 - 180 mm Tool cutting radius for straight cutter heads max. 163 mm Max. tool diameter behind stop level: 180 mm Max. throat depth: 35 mm Axis adjustment range: 55 mm 3rd spindle - left ----- Motor with brake: Shared motor with the 2nd spindle Spindle diameter: 40 mm Speed: 6,000 rpm Tool cutting radius 40 mm below table level: 93 - 200 mm Tool cutting radius 55 mm below table level: 93 - 180 mm Tool cutting circle for straight cutter heads max. 163 mm Max. throat depth: 35 mm Axial adjustment range: 55 mm Radial CNC-controlled spindle 4th spindle - top ----- Motor with brake: 11.0 kW Spindle diameter: 40 mm Speed: 6,000 rpm Tool cutting circle: 93 - 200 mm Tool cutting circle for straight cutter heads max.: 180 mm Max. throat depth: 35 mm Axial adjustment range: 40 mm Radial CNC-controlled spindle Split pressure shoe in front of the upper tool holder, adjustable to the tool cutting circle and pivoting away from the tool, spring-loaded. Pressure shoe before and discharge after the upper spindle with electronic digital displays, integrated into the memory function. 5th spindle - lower ----- Motor with brake: 7.5 kW Spindle diameter: 40 mm Speed: 6,000 rpm Tool cutting radius: 93 - 200 mm Max. groove depth: 15 mm Axis adjustment range: 35 mm Feed system ----- Electronic feed, continuously adjustable with brake: 4 kW, 5 - 30 m/min Feed roller in front of the first lower tool, pneumatically controlled up/down. Durofer pointed tooth rollers with depth gauge and self-cleaning. Adjustment range of the feed rollers relative to the left tool holder, axial: 35 mm Machine electrical system ----- Operating voltage 400 V (voltage range 380 - 420 V), 50 Hz. All spindles are IE 2 version. Electrical design according to DIN VDE 0113, electrical equipment for industrial machines EN60204, IEC-204-1. Other electrical regulations are not taken into account. Machine stands, tables, and stops -----...

Condition: new, Year of construction: 2024, functionality: fully functional, saw blade diameter: 600 mm, OPTIMIZATION CROSS-CUTTING SYSTEM WITH ROTATING SAWING UNIT CT600 / 6000 max. blank length 6,000 mm Cutting dimensions unit position A Ndsdov Aub Nspfx Abged At 0° 200x215, 50x370 mm At 30° 200x185 mm, 50x325 mm At 45° 200x150 mm, 50x265 mm At 80° 200x35 mm, 50x63 mm Cutting dimensions unit position B At 0° 160x315, 40x400 mm At 30° 160x270 mm, 40x350 mm At 45° 160x220 mm, 40x285 mm At 80° 160x52 mm, 40x70 mm Min. workpiece thickness 10 mm (with automatic feeding 20 mm) Support table inclined at 8° Slider stop side on the right Technical data saw unit: Aggregate completely rotatable with table Motor 7.5 KW, 400 Volt, 50 Hz HM saw blade diameter 600 mm, F=30, Z=60, S=5 Cutting cycle duration approx. 4 sec. Automatic rotation of the aggregate -70° to +70° Saw aggregate rotation -80° to +80° on request Rotation of the aggregate from 0° to 70° in approx. 1.3 sec. Positioning accuracy +/- 0.2° Hold-down system consisting of 2 pneumatic Pressure cylinders with mounted pressure rail Side pressure plate system with electronic control Technical data slider system: Feed via gear/rack system with "brushless" motor Positioning accuracy +/- 0.4 mm Power of the feed motor suitable for pushing a package weight of 80 kg Max. feed speed 90 m/min. Pneum. slider lift after completion of the cutting cycle and return above sliding level Control: 12 inch "touch screen" BECKHOFF professional PC with WINDOWS operating system USB port Ethernet port Loading and saving machine data via USB Editing cutting program directly on the input unit Transferring cutting lists via USB or Ethernet Direct import of .btl (10.4) format files Working software: Up to 1000 cutting lists with up to 11 different cutting dimensions or 1 list with 10000 different cutting dimensions. Cutting dimensions in sequence Cutting cycle with 4 optimization options (Max. length, min. waste, sequence, length priority) Graphic display of the workpiece Additional options installed: ZA110 discharge table (per meter) ZA040 saw unit table rotation 80°

Condition: used, Year of construction: 2012, total width: 1,750 mm, total length: 1,800 mm, total height: 1,600 mm, Weight: 1.900 kg Price: On request - Year: 2012 - Documentation available: Yes - CE marking present: Yes - Serial number: 12236 - Arbor hole saw blade diameter [mm]: 650 Njdpfx Abswniidegodd - Conveyor motor power [kW]: 0.8 - Conveyor width [mm]: 350 - Voltage [V]: 400 - Current consumption [A]: 80 - Fuse [A]: 100 - Power [kW]: 57.0 - Transport dimensions: 1800mm x 1750mm x 1600mm (l x w x h) - Transport weight [kg]: 1900kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels