Hydraulic plate shears

RAS , 2500 x 4 mm

Condition: good (used), Year of construction: 2000, sheet thickness steel (max.): 2 mm, sheet thickness aluminum (max.): 3 mm, Specifications : Maximum working length 2160 mm Maximum sheet thickness (steel 400 N/mm2) 2.0 mm Maximum thickness of sheet metal (stainless steel) 1.5 mm Maximum sheet metal thickness (aluminum) 3.0 mm Maximum development sheet width 1500 mm Maximum four-sided fold height max * 203 mm Bending blade reach 180 degrees Machine width 5500 mm approx. Iedsqzibtspfx Adnoa Machine length 7000 mm approx. Machine height 2500 mm Total weight 21000 kg Power 18 kW Frequency 50 Hz Pressure 6 bar INCLUDED drag loading system

Condition: used, Year of construction: 1985, sheet width 2500 mm plate thickness 6 mm rear stop 750 mm down holder 16 Stk Ijdpfx Adjt Sykqjnea total power requirement 12 kW weight 5400 kg dimensions of the machine ca. 3000 x 1500 x 2000 mm Equipment: - Electric backgauge 750 mm - Pneumatic sheet metal holders - 2x side stops - 3x front support arms - Ball rollers in the front support table - Rear sheet metal chute - Foot switch

Condition: used, turning diameter / mm turning length / mm swing diameter over bed slide / mm Technical data - Model 230 DIMENSIONS Centre height on the bed: 230 mm Spacing between centres: 1000-1500 mm 2000-2500 mm 3000 mm Bed width: 360 mm Largest turning Ø: on the bed: 465 mm on the carriage: 278 mm on fixed steady rest: 200 mm on travelling steady rest: 160 mm CROWNING Width of the crank: 300 mm Distance between face plate edge and offset: 150 mm Largest turning Ø on the offset: 690 mm SPINDLE Ø of front bearing (inside): 110 mm Ø of rear bearing (inside): 95 mm Ø of hole: 77 mm Mounting Type - Cam Lock: 6" Internal spindle taper - taper: 1 : 20 Spindle taper - C. M. - N.: 5 Speed ranges: Slow feed - rev. 1': 15÷1000 Normal feed - rev. 1': 22÷1500 Fast feed - rev. 1': 30÷2000 FEEDS (without gear change)-N.: 108 Longitudinal feed range at revs. : 0.04÷4 mm Transverse feed range at revolution: 0.02÷2 mm Lead screw - Ø: 40 mm Lead screw pitch: 12 mm THREAD (without gear change) Metric - N. 54 to: 0.5÷28 mm Module - N. 54 to Module: 0.25÷14 Whitworth - N. 54 to Wt. x 1": 56÷1 Diametral Pitch - N. 54 to D.P.: 112÷2 Inch - N. 54 to Inch: 1/32 ÷ 13 3/4" SPINDLE PIT Quill Ø: 75 mm Quill barrel: 220 mm Isdpfxewz Ryws Adnsa Quill taper - vices N. 5 POWER Main motor - HP: 10 Pump motor - HP: 0.25 WEIGHT approx. - kg 2000-2220 2530-2720 2920 ON REQUEST Main motor - HP

Condition: refurbished (used), functionality: fully functional, control type: CNC control, controller model: MB2000, working width: 3,200 mm, type of crowning: fixed, sheet thickness steel (max.): 4 mm, back gauge adjustment: CNC-controlled, back gauge: 1,500 mm, Equipment: documentation/manual, emergency stop, RAS 74.30 Multibend 2000 Technical Data: Back gauge: CNC 1500 mm Max. sheet thickness: 4 mm Working width: 3200 mm Equipment: pointed rail and bending rail Iodpfx Aexhd H Iodnja Motorized adjustment of the bending beam, Safety stop (finger guard), emergency stop cable Various tools available as options Gooseneck segments available on request

Condition: excellent (used), Year of construction: 2002, RAS Multibend Center 79.22 Isdpsrxt Axsfx Adnsa Automatic cnc FOLDER / Panel bender Year 2002 Specifications • Working Length: 2160 mm/ 7.09’ ft. • Maximum Sheet Metal Thickness: Steel – (400N/mm2) 2.0 mm • Maximum Sheet Metal Thickness: Stainless Steel – 1.5 mm • Maximum Sheet Metal Thickness: Aluminum – 3.0 mm • Maximum Development Sheet Width: 1500 mm/ 4.92’ ft. • Maximum Four-Sided Fold Height Max: 203 mm • Bending Blade Reach: 180 ° Degrees • Machine Width: 5500 mm approx./ 18.04’ ft. approx. • Machine Length: 7000 mm approx. / 22.97’ ft. approx. • Machine Height: 2500 mm/ 8.20’ ft. Power: 18 kW Frequency: 50hZ Pressure: 6 Bar Weight: 21,000 kg/ 46,297 lbs. approx.

Condition: ready for operation (used), De uitrusting bestaat uit: - 3 afwikkelaars Elba 5 ton capaciteit - 1500 mm - Richtunit RAS 26.45 - Ras hoekuitsparingeenheid - Rashydr-unit voor het walsen van verstevigingsribben in het plaatwerk - Rasschaar voor het op lengte knippen RAS 82.16 - Ras vouwmachine snelheid: 15 m/min Vermogen: 16 kW Iedswwbf Nepfx Adnoa

Condition: good (used), Year of construction: 1991, Sheet width 2500 mm Sheet thickness 4 mm Cutting angle 1.49 ° Ijdpfetq S T Nox Adnoa Strokes per minute 40-80 Stand projection 200 mm Number of hold-down devices 13 pieces Backgauge - adjustable 5-1000 mm Table height 750 mm Oil capacity 85 l Air pressure - required 5 bar Machine weight approx. 3600 kg

Condition: good (used), Year of construction: 1985, machine/vehicle number: 4888, Offer 25234 Technical Data: - Drilling capacity in steel ST 60: 32 mm - Maximum drilling diameter in steel ST 60: 40 mm - Long spindle MK 3 - Drill spindle speeds steplessly adjustable - Range 1: 160 – 1125 rpm Iodpswylvqofx Adnoa - Range 2: 320 – 2250 rpm - Drill spindle stroke: 120 mm - Feeds: 0.1 + 0.2 mm/rev - Throat depth: 293 mm - Column diameter: 115 mm - Table size: 300 x 300 mm - With 2 T-slots 14 x 224 mm - Emergency stop button - Machine vice - 10 pcs. HSS drill bits 10 – 25 mm - Required space approx.: W 500 x H 1750 x D 900 mm - Weight approx.: 270 kg

Condition: ready for operation (used), Year of construction: 2001, control type: NC control, working width: 2,500 mm, sheet thickness (max.): 6 mm, back gauge: 1,000 mm, overall weight: 6,700 kg, total length: 2,800 mm, total width: 3,950 mm, total height: 1,900 mm, power: 7.5 kW (10.20 HP), stroke length: 450 mm, Motorized swing bending machine Manufacturer: HERA Model: SM4 2500x6mm Year of manufacture: 2001 Technical data Manufacturer: HERA Model: SM 4 Year: 2001 Capacity: 2520 x 6 mm Upper beam stroke: 450 mm Lower beam adjustment: max. 100 mm Bending beam adjustment: max. 100 mm Connected load: Upper beam 5.5 kW / Bending beam 7.5 kW Operating voltage: 400 V / 50 Hz Control voltage: 230 V Dimensions approx.: L 3.95 x W 2.80 x H 1.9 m Weight: 6.7 t Iodpjwxc Rpefx Adnoa Equipment • 2 x sharp rail • Bending rails: 10mm, 20mm, 40mm • Segmented gooseneck set: H 120mm • Motorized bending beam adjustment • Hydraulic tool clamping • Programmable backgauge 10–1000mm All information provided without guarantee. A live demonstration is possible at any time in our showroom.

Condition: good (used), functionality: fully functional, Year of construction: 1998, working width: 2,000 mm, pressing force: 35 t, pressure 35to max. bending length 2000mm arrester behind drive capacity 4,5 kW weight 3000kg Iedpowagykofx Adnsa