Used Wood Hydraulic Press for sale (47,190)

Condition: used, Year of construction: 1970, pressure 1000 t distance between columns 5000 mm stroke 500 mm Height of centres 400 mm Overall size 6000 x 2500 mm Iaodpewwl R Aofx Ah Nol Weight 1000 kg Distance between centres 3500 mm weight of the machine ca. 220 t

Condition: used, Revolver Briquetting Press RUF Type RBK 55/2500/120 S Hydraulic pellet press or briquetting press for grinding sludge ALU chips, metal shavings, or similar materials Serial No. 70002 Year of manufacture: 2009 Briquette diameter: 120 mm Briquette length in pre-compactor: approx. 120 mm Pressing force in pre-compactor: 30 tons at 260 bar Briquette length in main compactor: approx. 80 mm Main press cylinder force: 250 tons at 260 bar Main press cylinder stroke: 120 mm Counter press cylinder force: 250 tons at 260 bar Counter press cylinder stroke: 15 mm Main press cylinder piston diameter: 350 mm Press cycle time: approx. 30 sec. with grinding sludge with low residual oil content Hopper size of screw conveyor: 1000 x 600 mm Hydraulic motor power: 37 kW Electrical connection: 400 V, 50 Hz, 45 kW - Revolver with 5 stations for high material throughput - Pre-compaction stage for feeding material into the revolver disk - 2 opposing main press cylinders with 120 mm and 15 mm stroke - Ejector cylinder for discharging finished briquettes from the revolver disk - Infinitely variable hydraulic speed adjustment for each pressing stage - Previously used for grinding sludge from metalworking - Material bunker as a hopper with screw conveyor - In 2018, the machine was fully overhauled by RUF - In 2020, a new SIEMENS Simatic touch panel was installed Isdpfxshg Uz Ie Ah Njal - Only a few operating hours since overhaul Very good condition Grinding Sludge Recycling - Major cost savings through coolant recovery - Significant reduction in disposal costs thanks to volume and weight reduction of grinding sludge - Grinding sludge briquettes with low residual oil content may potentially be classified as 'non-hazardous waste.' Practical test on 15.01.2026 with aluminum shavings: With optimized parameters, the machine achieves a pressing output of 230 kg aluminum chips per hour. A further increase in performance appears possible in principle, but could not be verified due to lack of material. (see video)

Condition: reconditioned (used), NR.01 Hydraulic press with 3 cylinders BIGNOZZI Power 200 Ton Completamete reconditioned Table 1550 x 1050 mm Recess mm 1000 Iasdpfx Ahjhnc R Is Nol Piston stroke mm 500 Platen height 1180 Dimensions 2900 x 1700 x 2900 ( h) Weight Ton 10

Condition: good (used), Year of construction: 2000, operating hours: 5,000 h, functionality: fully functional, machine/vehicle number: 2089, total height: 5,000 mm, table height: 1,000 mm, total width: 3,000 mm, pressing force: 250 t, overall weight: 25,000 kg, MIB BRAND HYDRAULIC PRESS YEAR 01/2000 CAPACITY 250T Iaodpfxov Hbh Re Ah Nol MACHINE TO BE RESTORED, COMPLETE

Condition: new, Year of construction: 2026, TECHNICAL DATA Pressing force 30t max. load prism jaw 7.5t piston stroke 160mm piston travel 550mm Dimensions and weights length (product) approx. 1240mm width/depth (product) approx. 650mm Height (product) approx. 1920mm Weight (net) approx. 280kg Clear width 790mm Installation height max. 1030mm Frame depth 200mm SCOPE OF DELIVERY 2-part prism set for inserting round material Hand and foot lever Iaodpfx Aei Amnpjh Nol Winch for lifting and lowering the table Location: Ex works - available at short notice -

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: SÇ 902 S Hidrolik Alüminyum Köşe Presi Makinesi, • Complies with CE standards • Corner press machine designed for joining aluminium profiles at 90 degrees • 2 upper presses and blade movement are hydraulic • Equipped with a mm scale system for adjusting blade height and feed • Centering square stop is hydraulic • Drain button for fine adjustment is available • Machine comes with 2 pieces of 4 mm blades Iedpfx Ahjrbk Tfj Neal • 2 pedals are used for hydraulic pressing and profile clamping • Polyamide plate is provided to prevent damage to profile surfaces • Left and right profile support arms are available

Condition: ready for operation (used), Year of construction: 1987, functionality: fully functional, pressing force: 200 t, Hans Schoen NH/LF 200 (UVV) – Powerful & Robust 🔧 Model: Hans Schoen NH/LF 200 📍 Type: Hydraulic Double-Column Press (UVV-certified) 📅 Year of manufacture: approx. 1988 (depending on the specific machine) 📦 Condition: used, fully functional ⸻ 💪 Technical Highlights • Pressing force: approx. 200 t – suitable for demanding forming and drawing applications • Hydraulic drive for precise force and stroke control • Column clearance: approx. 1,050 mm – generous working area • Stroke: approx. 150 mm – efficient travel distance • Table size: approx. 1,000 × 1,200 mm – large clamping area • Table height above floor: approx. 850 mm – ergonomic working height • Hydraulic control (often with PLC/Siemens control) possible • Safety and UVV certification for manual loading – increased operational safety Iedpfx Aox Ry Nyjh Njal 💡 Thanks to its robust construction, this press is ideally suited for series production, drawing and forming processes as well as machining and assembly tasks in metalworking operations. ⸻ 📌 Features & Equipment • Two-hand operation / safety control • Adjustable mechanical stop • Pressure cut-off • Pressure switch • UVV-compliant safety features → all for efficient and safe operation on the shop floor Currently UVV-certified. ⸻ 🛠️ Applications This press offers versatile usage, such as for: • Metal forming / drawing work • Assembly and joining part production • Testing and quality control processes • Series and small batch production ⸻ 📦 Size & Weight • Dimensions (approx.): Width × Depth × Height ≈ 4.0 × 3.6 × 3.4 m • Weight: approx. 16 t – robust industrial construction

Condition: used, HYDRAULIC DOUBLE COLUMN PRESS CAMP 250 tn Double column press Iodpfxegr Ur Ro Ah Neal Pressing power 250 tn Stroke of the piston 500 mm Table size 570 x 570 mm Distance from table to piston 600 mm Distance between uprights 570 mm Approach speed 95 mm/seg Workin speed 7.5 mm/seg Retraction speed 135 mm/ seg Engine power 30 cv

Condition: good (used), Lechner IV B Hydraulic Bookbinding Press The machine is ready to operate. The press has a built-in hydraulic unit. Four stations. Iaedpfx Asx N D Speh Nel Irreplaceable in bookbinding for the production of books, pads, etc.

Condition: used, Year of construction: 1996, Technical details: pressure: 6,3 t throat: 170/180 mm stroke: 310 mm Iasdpjtxdmwsfx Ah Nol power capacity: 3 kW dayligth: 775 mm weight of the machine ca.: 1,5 t clamping table: 470 x 330 mm table height over floor: 800 mm C-Type 1 Station *

Condition: used, Year of construction: 2003, functionality: fully functional, overall weight: 3,500 kg, pressing force: 60 t, input frequency: 50 Hz, operating temperature: 100 °C, input voltage: 380 V, cylinder diameter: 65 mm, SECOND-HAND UNIVERSAL HOT PRESS FOR VENEER AND SOLID WOOD GLUED PANELS WITH SIDE PRESSURE CYLINDERS ORMA MOD. NPC/L Vertical thrust - Total thrust – 60 tons - Specific pressure – 2 kg/cm2 - Plate dimensions – 2500x1300 mm - Cylinders – 4 - Cylinder diameter – 70 mm - Electric boiler thermal power – 18 kW - Voltage – 400/3/50 Hz Horizontal thrust - Total thrust – 25 tons - Cylinders – 5 - Cylinder diameter - ø 65/40 mm - Operating temperature - 100°C - Weight - 3.5 tons Iajdpsx Rrb Iefx Ah Njl - Power - 21 kW 29 A - Voltage - 380/3/50 Hz - Dimensions - 3100 x 1650 x 1800 mm - CE standard - Year 2003

Condition: good (used), Year of construction: 1969, Hydraulic press, single-column press, C-column press, oil-hydraulic press, hydraulic single-column press, press machine, hydraulic punch for Schüco tools, hydraulic press, multifunctional punch, punch, universal punch, punching machine -Handover: in the current condition as viewed -Condition: Cylinder slightly leaky -Hydraulic press: Hydraulic single-column press -Pressing force: 160 tons -Stroke: 600 mm -Insertion height: 800 mm -Table size: 660 x 800 mm -Table hole: Ø 250 mm -Projection: 330 mm -Operation: hand lever Iaedjw A Rzdjpfx Ah Njl -Dimensions: 1780/1090/H2920 mm -Weight: 8000 kg

Condition: used, Year of construction: 1992, functionality: fully functional, installation height: 500 mm, table width: 1,400 mm, stroke length: 300 mm, • Type of machine: Hydraulic press / C-frame press • Manufacturer: Müller Weingarten (historic German engineering company) • Model designation: CKD 100 4.1 • Applications: Iasdpfx Ahox Ry Hrj Nol • Forming, punching, pressing of metal or plastic components • Small and medium batch production • Tool and die making • Design: Robust H-frame or single-column construction, suitable for precise pressing and forming operations • Capacity: Typically around 100 t pressing force (number indicates approx. 100 metric tons nominal force—common for CKD models) 📐 Typical Features • Hydraulic drive: Precise control of force and stroke • Stroke range: Sufficient for versatile applications (e.g. drawing, bending, punching) • Stable construction: Designed for continuous industrial operation • Tool integration: Mounting options for custom tools and dies • Operation: Usually manual or semi-automatic, depending on year of manufacture 🧱 Typical Uses Hydraulic presses like the CKD series are used in production for: • Metal forming (e.g. bending, deep-drawing) • Assembling components by pressing • Assembly processes with defined force • Quality assurance and test pressing Complete circuit diagrams and documentation available! Inspection under power possible at any time.

Condition: used, Year of construction: 2003, Working height: 2300 mm, Working width: 3500 mm, Motor: 1.5 kW, 3 pressure cylinders from above, 2 from the side, Pressure per cylinder: 3000 kg, Cylinder stroke: up to 200 mm, Hydraulics: 10-150 bar, Space required: 3950 x 900 x 2550 mm, Weight: 670 kg Storage location: Nattheim Iaodpfxevvkmbj Ah Nsl

Condition: good (used), Karl Tranklein Z.P. Hydraulic Bookbinding Press The machine is ready to operate. Isdox N Dwlspfx Ah Neal The press has a built-in hydraulic unit. Two independent stations. Irreplaceable in bookbinding for the production of books, blocks, etc.

Condition: used, Year of construction: 1982, Technical details: Isdpfsrdlgiox Ah Nsal pressure: 2,5 t

Condition: used, Press capacity: 50 ton Throat depth: 265 mm Stroke: 250 mm Daylight: 400 mm Table surface area : 700 x 450 mm Slide area: 550 x 300 mm Table height over floor: 850 mm Ijdjwyplcopfx Ah Neal Approach speed: 32 mm / sec Working speed: 6,3 mm / sec Return speed: 42 mm / sec Required power: 4 kW Dimensions L x W x H: 1290 x 1160 x 2085 mm Weight of machine approx.: 1,75 ton

Condition: new, 4 glueing poles, 1 pressing bar, hydraulic, Iedpfjvrv H Sex Ah Njal external sizes L x H 3000 x 2000 mm, ca. 200 kg

Condition: new, Year of construction: 2025, pressing force: 300 t, table width: 1,000 mm, table length: 1,000 mm, clearance between the columns: 1,000 mm, retraction force: 100 t, stroke length: 800 mm, operating pressure: 250 bar, Equipment: documentation/manual, safety light barrier, CRONOSSTECH 300 / 100 Ton Four-Column Hydraulic Deep Drawing Press General Description The CRONOSSTECH 300 / 100 ton four-column hydraulic deep drawing press is a high-rigidity, four-column hydraulic press solution developed for metal forming, deep drawing, and precision pressing applications. Its St52 grade steel frame undergoes stress-relieving via vibration, ensuring stable parallelism and perpendicularity tolerances throughout the full stroke. The ram and bolster systems operate independently; stroke length and tonnage settings can be precisely controlled via the touch panel interface. Equipped with REXROTH or PARKER hydraulic components, an IE3 class motor, and PLC-controlled structure, the machine provides high efficiency and reliable operation. The automatic lubrication system and electronic filter contamination alerts minimize maintenance requirements. With a 300 / 100 ton capacity, this model is an ideal industrial press solution for medium to high tonnage metal forming, deep drawing, and die applications. Key Advantages - High-rigidity four-column press frame - Independent stroke and tonnage adjustment for ram and bolster - Full control via touch panel - High precision and repeatability - Long lifespan, low maintenance design Fields of Application - Metal forming applications - Deep drawing operations - Die testing and production lines - Auxiliary pressing processes ⚙️ STANDARD AND TECHNICAL SPECIFICATIONS TYPE: Four-Column FRAME MATERIAL: St52 – ERDEMİR COLUMN SHAFT DIAMETER: Ø 90 mm – 4 pcs, induction-hardened chrome-plated shafts SLIDE BEARING: Bronze Zr14 CAPACITY (RAM): 300 Ton CAPACITY (BOLSTER): 100 Ton DISTANCE BETWEEN COLUMNS: 1000 × 1000 mm PARALLELISM TOLERANCE: 120 micron/m PERPENDICULARITY TOLERANCE: 60 micron/m STROKE (RAM): 800 mm STROKE (BOLSTER): 200 mm MIN. CLEARANCE: 100 mm Iasdpfx Ajx N Unzeh Nsl MAX. CLEARANCE: 900 mm WELDING STRESS RELIEF: Vibration stress relief WELDING PRACTICE: TÜRK-AK accredited WPQR & WPS – EN ISO 15614-1:2017 (EN ISO 14731) MAX. WORKING PRESSURE: 250 Bar TOTAL MOTOR POWER: 30 kW – IE3 MAIN PUMP: 45 cm³ – REXROTH or PARKER MOVING TABLE FAST DESCENT SPEED: 150 mm/s FORMING SPEED: 12 mm/s RETURN SPEED: 170 mm/s BOLSTER TABLE FORWARD SPEED: 30 mm/s MAIN CYLINDER BORE: Ø 390 mm – Ck45 BOLSTER CYLINDER BORE: Ø 230 mm – Ck45 AUXILIARY BOOSTER CYLINDERS: 2 Units APPROX. PRESS DIMENSIONS: 4000 × 1450 × 1450 mm BOTTOM TABLE HEIGHT FROM FLOOR: 1300 mm FRONT CHARGE VALVE: NG 125 HYDRAULIC UNIT: REXROTH or PARKER COOLING SYSTEM: EMMEGI – CIESSE – PARKER OFF-LINE FILTRATION: REXROTH or PARKER PLC: DELTA TOUCH PANEL: DELTA 7” SWITCHGEAR COMPONENTS: SIEMENS – SCHNEIDER APPROX. WEIGHT: 18 Ton Production Note This machine is manufactured in Turkey by CRONOSSTECH.

Condition: good (used), Atom SE 25 Hydraulic Arm Press This machine is in perfect condition and ready to operate. Isdpox Nc Agsfx Ah Njal It is ideal for die-cutting difficult materials, particularly in the leather goods and printing industries. It can be used with both leather goods and bookbinding dies. It cuts paper, cardboard, leather, plastic, etc. Pressure: 25 tons Power: 380V Table dimensions: 1000mm x 500mm Hammer dimensions: 500mm Maximum stroke: 90mm Motor power: 0.9kW Weight: 1030kg Two-handed control.

Condition: used, Year of construction: 1991, machine/vehicle number: 041-024/39, Press capacity: 63 ton Ijdpovai R Tofx Ah Nsal Throat depth: 360 mm Stroke: 500 mm Daylight: 800 mm Table surface area : 750 x 560 mm Slide area: 630 x 400 Working speed: 60 mm / sec Return speed: 380 mm / sec Electrical connected load: 12,6 kW Dimensions L x W x H: 1.200 x 1.950 x 2.800 mm Weight of machine approx.: 4,3 ton

Condition: new, Year of construction: 2025, pressing force: 250 t, table width: 1,000 mm, table length: 1,000 mm, clearance between the columns: 1,000 mm, retraction force: 80 t, stroke length: 800 mm, operating pressure: 250 bar, Equipment: documentation/manual, safety light barrier, CRONOSSTECH 250 / 80 TON FOUR-COLUMN HYDRAULIC DRAWING PRESS General Description The CRONOSSTECH 250 / 80 ton four-column hydraulic drawing press is a high-rigidity hydraulic solution designed for precision metal forming, deep drawing, and press applications. The frame is constructed of St52 grade steel and undergoes stress relief through vibration, ensuring high parallelism and perpendicularity tolerances during long-term operation. The ram and cushion systems operate independently; stroke and pressure settings can be precisely adjusted via the touch panel. Iaedpfex N Um Rsx Ah Nel With hydraulic components from REXROTH or PARKER, an IE3 efficiency-class motor, and PLC-controlled system, it offers high performance and reliable operation. An automatic lubrication system and electronic filter contamination alerts minimize maintenance requirements. With its 250 / 80 ton forming capacity, this model is an ideal industrial press solution for medium- and heavy-duty metal forming, deep drawing, and die applications. Key Advantages - Four-column, high-rigidity press frame - Independent stroke and tonnage settings for the ram and cushion - Full control via touch panel - High precision and repeatability - Long service life with low maintenance costs Areas of Use - Metal forming applications - Deep drawing operations - Die testing and production lines - Auxiliary pressing processes ⚙️ STANDARD AND TECHNICAL SPECIFICATIONS TYPE: Four-column FRAME MATERIAL: St52 – ERDEMIR COLUMN SHAFT DIAMETER: Ø 90 mm – 4 pcs. induction hardened chrome-plated shafts SLIDE GUIDING: Bronze Zr14 CAPACITY (RAM): 250 Ton CAPACITY (CUSHION): 80 Ton DISTANCE BETWEEN COLUMNS: 1000 × 1000 mm PARALLELISM TOLERANCE: 120 micron/meter PERPENDICULARITY TOLERANCE: 60 micron/meter STROKE (RAM): 800 mm STROKE (CUSHION): 200 mm MIN. OPENING HEIGHT: 100 mm MAX. OPENING HEIGHT: 900 mm STRESS RELIEVING: Vibration stress relief WELDING APPLICATION: WPQR & WPS accredited by TÜRK-AK – EN ISO 15614-1:2017 (EN ISO 14731) MAX. WORKING PRESSURE: 250 Bar TOTAL MOTOR POWER: 22 kW – IE3 class MAIN PUMP: 36 cm³ – REXROTH or PARKER MOVABLE TABLE FAST DESCENT: 150 mm/sec FORMING SPEED: 12 mm/sec RETURN SPEED: 170 mm/sec CUSHION TABLE FORWARD SPEED: 30 mm/sec MAIN CYLINDER BORE: Ø 360 mm – Ck45 CUSHION CYLINDER BORE: Ø 200 mm – Ck45 AUXILIARY BOOST CYLINDERS: 2 units APPROXIMATE PRESS DIMENSIONS: 4000 × 1450 × 1450 mm BOTTOM TABLE HEIGHT FROM FLOOR: 1300 mm FRONT CHARGING VALVE: NG 125 HYDRAULIC UNIT: REXROTH or PARKER COOLING SYSTEM: EMMEGI – CIESSE – PARKER OFF-LINE FILTRATION: REXROTH or PARKER PLC: DELTA TOUCH PANEL: DELTA 7” ELECTRICAL COMPONENTS: SIEMENS – SCHNEIDER APPROXIMATE WEIGHT: 16 Tons Production Note This machine is manufactured in Turkey by CRONOSSTECH.

Condition: new, Year of construction: 2025, pressing force: 200 t, table width: 1,000 mm, table length: 1,000 mm, clearance between the columns: 1,000 mm, retraction force: 70 t, stroke length: 800 mm, operating pressure: 250 bar, Equipment: documentation/manual, safety light barrier, CRONOSSTECH 200 / 70 TON FOUR-COLUMN HYDRAULIC DEEP DRAWING PRESS General Description The CRONOSSTECH 200 / 70 ton four-column hydraulic deep drawing press is a high-rigidity, four-column hydraulic press designed for metal forming, deep drawing, and precision pressing applications. The St52 grade welded steel frame is subjected to stress relief via vibration, ensuring high parallelism and perpendicularity tolerances are maintained over extended operation. The ram and blank holder (pot) systems are operated independently, with stroke and pressure settings precisely adjustable via touchscreen control panel. Equipped with REXROTH or PARKER hydraulic components, an IE3 class motor, and PLC-controlled structure, the system offers high efficiency and reliable operation. An automatic lubrication system and electronic filter contamination alerts minimize maintenance requirements. With its 200 / 70 ton capacity, this model provides an ideal industrial solution for medium and heavy-duty metal forming, deep drawing, and die applications. Key Advantages - Rigid four-column press frame - Independent stroke and tonnage adjustment for ram and blank holder - Full control via touchscreen panel - High precision and repeatability - Long-lasting, low-maintenance design Applications Iedpox N Umqjfx Ah Nsal - Metal forming operations - Deep drawing applications - Die trial and production lines - Auxiliary pressing operations ⚙️ STANDARD AND TECHNICAL SPECIFICATIONS TYPE: Four-column FRAME MATERIAL: St52 – ERDEMIR grade COLUMN SHAFT DIAMETER: Ø 90 mm – 4 pcs, induction hardened and chrome plated SLIDE BEARING: Bronze Zr14 CAPACITY (RAM): 200 Ton CAPACITY (BLANK HOLDER): 70 Ton DISTANCE BETWEEN COLUMNS: 1000 × 1000 mm PARALLELISM TOLERANCE: 120 micron/meter PERPENDICULARITY TOLERANCE: 60 micron/meter STROKE (RAM): 800 mm STROKE (BLANK HOLDER): 200 mm MIN. OPENING HEIGHT: 100 mm MAX. OPENING HEIGHT: 900 mm WELDING STRESS RELIEF: By vibration WELDING PROCEDURE: WPQR & WPS with TURK-AK accreditation – EN ISO 15614-1:2017 (EN ISO 14731) MAX. WORKING PRESSURE: 250 Bar TOTAL MOTOR POWER: 22 kW – IE3 MAIN PUMP: 36 cm³ – REXROTH or PARKER MOVING TABLE FAST DESCENT: 150 mm/sec FORMING SPEED: 12 mm/sec RETURN SPEED: 170 mm/sec BLANK HOLDER FORWARD SPEED: 30 mm/sec MAIN CYLINDER BORE: Ø 320 mm – Ck45 BLANK HOLDER CYLINDER BORE: Ø 190 mm – Ck45 AUXILIARY SPEED-UP CYLINDERS: 2 units PRESS APPROX. DIMENSIONS: 4000 × 1450 × 1450 mm LOWER TABLE HEIGHT FROM FLOOR: 1300 mm MAIN CHARGE VALVE: NG 125 HYDRAULIC UNIT: REXROTH or PARKER COOLING SYSTEM: EMMEGI – CIESSE – PARKER OFF-LINE FILTRATION: REXROTH or PARKER PLC: DELTA TOUCHSCREEN PANEL: DELTA 7” CONTROL COMPONENTS: SIEMENS – SCHNEIDER APPROX. WEIGHT: 14.5 Ton Production Note This machine is manufactured by CRONOSSTECH in Turkey.

Condition: new, Year of construction: 2025, pressing force: 150 t, table width: 800 mm, table length: 800 mm, clearance between the columns: 800 mm, stroke length: 600 mm, operating pressure: 250 bar, Equipment: documentation/manual, safety light barrier, CRONOSSTECH 150/50 TON FOUR-COLUMN HYDRAULIC DEEP DRAWING PRESS General Description The CRONOSSTECH 150/50 ton four-column hydraulic deep drawing press is an industrial press solution developed for metal spinning, deep drawing, and precision pressing applications, featuring a robust four-column frame construction. The St52 grade steel construction frame undergoes stress relieving via vibration. This ensures high parallelism and vertical tolerance are maintained during prolonged operations. Ram and blank holder systems operate independently; stroke and pressure adjustments can be made precisely via the touchscreen panel. Equipped with REXROTH or PARKER hydraulic equipment, an IE3 classified motor, and PLC control, the press delivers high efficiency, reliability, and long service life. Automatic lubrication and electronic filter contamination alerts minimize maintenance requirements. With a 150/50 ton capacity, this model is an ideal solution for mass production, mold testing, and medium to heavy-duty deep drawing applications. Key Advantages - Rigid four-column press frame - Independent stroke and tonnage adjustment for ram and blank holder - Full control via touchscreen panel - High precision and repeatability - Low maintenance cost and long service life Fields of Application - Metal spinning processes - Deep drawing applications - Die testing and production processes - Auxiliary pressing operations ⚙️ STANDARD AND TECHNICAL FEATURES TYPE: Four-column FRAME MATERIAL: St52 – ERDEMIR COLUMN SHAFT DIAMETER: Ø 90 – 4 pcs, induction-hardened, chrome-plated shafts SLIDE BEARING: Bronze Zr14 CAPACITY (RAM): 150 ton CAPACITY (BLANK HOLDER): 50 ton DISTANCE BETWEEN COLUMNS: 800 × 800 mm PARALLELISM TOLERANCE: 120 micron/meter PERPENDICULARITY TOLERANCE: 60 micron/meter STROKE (RAM): 600 mm STROKE (BLANK HOLDER): 200 mm MIN. DAYLIGHT: 100 mm MAX. DAYLIGHT: 700 mm Iodpfxox N Ul To Ah Neal WELDING STRESS RELIEF: Vibration stress relief WELDING STANDARD: TÜRK-AK accredited WPQR & WPS – EN ISO 15614-1:2017 (EN ISO 14731) MAX. OPERATING PRESSURE: 250 Bar TOTAL MOTOR POWER: 18.5 kW – IE3 MAIN PUMP: 36 cm³ – REXROTH or PARKER MOVABLE TABLE FAST DESCENT SPEED: 150 mm/s MOVABLE TABLE DRAWING SPEED: 12 mm/s MOVABLE TABLE RETURN SPEED: 170 mm/s BLANK HOLDER FORWARD SPEED: 30 mm/s MAIN CYLINDER BORE: Ø 280 mm – Ck45 BLANK HOLDER CYLINDER BORE: Ø 160 mm – Ck45 AUXILIARY ACCELERATION CYLINDERS: 2 units APPROXIMATE PRESS HEIGHT: 3800 mm APPROXIMATE PRESS WIDTH: 1150 mm APPROXIMATE PRESS DEPTH: 1150 mm DISTANCE FROM FLOOR TO LOWER TABLE: 1200 mm PRIMARY FILLING VALVE: NG 125 HYDRAULIC UNIT: REXROTH or PARKER COOLING SYSTEM: EMMEGI – CIESSE – PARKER OFF-LINE FILTRATION: REXROTH or PARKER LUBRICATION TYPE: Automatic (adjustable from screen) RAM / BLANK HOLDER STROKE AND TONNAGE ADJUSTMENT: Adjustable from screen SYSTEM & PRESS STATUS INFORMATION: Viewable on screen DIE MEMORY: Adjustable from screen LINEAR DISPLACEMENT TRANSDUCER: NOVATECHNIK or TURCK PLC APPLICATION: DELTA TOUCHSCREEN PANEL: DELTA 7” SWITCHGEAR COMPONENTS: SIEMENS – SCHNEIDER APPROXIMATE WEIGHT: 9 ton Production Note This machine is manufactured in Turkey by CRONOSSTECH.

Condition: new, Year of construction: 2025, pressing force: 100 t, table width: 800 mm, table length: 800 mm, clearance between the columns: 800 mm, retraction force: 40 t, stroke length: 600 mm, operating pressure: 250 bar, Equipment: documentation/manual, safety light barrier, CRONOSSTECH 100/40 TON FOUR-COLUMN HYDRAULIC DEEP DRAWING PRESS General Description The CRONOSSTECH 100/40 ton four-column hydraulic deep drawing press is an industrial press solution designed for metal forming, deep drawing, and precision pressing applications, featuring a rigid four-column body construction. The St52 grade steel frame is stress-relieved via vibration methods, ensuring long-term retention of high parallelism and squareness tolerances. The ram and bolster systems operate independently, with stroke and pressure settings precisely controlled via a touchscreen interface. Iodsx N Ulyepfx Ah Nsal Equipped with REXROTH or PARKER hydraulic components, IE3 class motor, and PLC-controlled systems, it provides high efficiency, reliability, and extended service life. The automatic lubrication system and electronic filter contamination alerts keep maintenance requirements to a minimum. This model is the ideal solution for medium-scale mass production, die testing, and precision forming applications. Key Advantages - Rigid four-column press frame - Independent stroke and tonnage adjustment for ram and bolster - Full control via touchscreen panel - High precision and repeatability - Low maintenance costs, long service life Areas of Application - Metal forming operations - Deep drawing applications - Die testing and prototype production - Auxiliary pressing operations ⚙️ STANDARD AND TECHNICAL SPECIFICATIONS TYPE: Four-column FRAME MATERIAL: St52 – ERDEMİR COLUMN SHAFT DIAMETER: Ø 90 mm – 4 pcs. induction-hardened chrome-plated shafts SLIDE BEARING: Bronze Zr14 CAPACITY (RAM): 100 Ton CAPACITY (BOLSTER): 40 Ton DISTANCE BETWEEN COLUMNS: 800 × 800 mm PARALLELISM TOLERANCE: 120 micron/m SQUARENESS TOLERANCE: 60 micron/m STROKE (RAM): 600 mm STROKE (BOLSTER): 200 mm MIN. DAYLIGHT: 100 mm MAX. DAYLIGHT: 700 mm WELDING STRESS RELIEF: Vibration stress relieving WELDING APPLICATION: TÜRK-AK accredited WPQR & WPS – EN ISO 15614-1:2017 (EN ISO 14731) MAX. OPERATING PRESSURE: 250 Bar TOTAL MOTOR POWER: 15 kW – IE3 MAIN PUMP: 22 cm³ – REXROTH or PARKER MOVABLE TABLE FAST DESCENT SPEED: 150 mm/s MOVABLE TABLE FORMING SPEED: 12 mm/s MOVABLE TABLE RETURN SPEED: 170 mm/s BOLSTER TABLE ADVANCE SPEED: 30 mm/s MAIN CYLINDER BORE: Ø 230 mm – Ck45 BOLSTER CYLINDER BORE: Ø 145 mm – Ck45 AUXILIARY ACCELERATION CYLINDERS: 2 pcs APPROX. PRESS HEIGHT: 3,500 mm APPROX. PRESS WIDTH: 1,150 mm APPROX. PRESS DEPTH: 1,150 mm BOTTOM TABLE HEIGHT FROM FLOOR: 1,200 mm PRE-FILL VALVE: NG 100 HYDRAULIC POWER UNIT: REXROTH or PARKER COOLING SYSTEM: EMMEGI – CIESSE – PARKER OFF-LINE FILTRATION: REXROTH or PARKER LUBRICATION TYPE: Automatic (adjustable via screen) RAM / BOLSTER STROKE AND TONNAGE ADJUSTMENT: Adjustable from screen SYSTEM & PRESS STATUS INFORMATION: Viewable on screen DIE MEMORY: Adjustable via screen LINEAR POSITION ENCODER: NOVATECHNIK or TURCK PLC SYSTEM: DELTA TOUCHSCREEN PANEL: DELTA 7” SWITCHGEAR COMPONENTS: SIEMENS – SCHNEIDER APPROX. WEIGHT: 7.5 Ton Manufacturing Note This machine is manufactured by CRONOSSTECH in Turkey.