Used Wood Hydraulic Press for sale (50,141)

Condition: used, Hydraulic Synchronizing Press, Spotting Press AGEO Type GHP 200 H6 4-Column Hydraulic Press, Tool Trial Press, Spotting Press Serial No. 21169 Year of manufacture: 1993 Pressing force: 200 tons Clearance between uprights (front): 1200 mm Dodpjwva I Hjfx Afzoku Upright opening (side): 650 mm Table surface: 1560 x 1010 mm Ram surface: 1560 x 1010 mm Ram stroke: 575 mm Draw cushion stroke: 300 mm Draw cushion holding force: 63 tons Draw cushion ejector force: 30 tons Max. installation height: 775 mm Table height above floor: 1000 mm Guide column Ø: 140 mm Clamping pin bore in ram: 64 mm Pressing speed: 0 to 10 mm/s, stepless Return speed: 0 to 20 mm/s, stepless Main motor power: 22 kW Control pump motor power: 5.5 kW Connection: 400 Volts, 50 Hz - Table and ram with 22 mm T-slots - Two pressure cylinders with electronic precision synchronization control - Stepless electronic stroke limitation (top and bottom with digital travel measurement and position display) - Mechanical safety support device (prevents ram from dropping due to dead weight) - Single-hand and two-hand operation - Electrical tool safety via signal contact - Pressure presetting independent of stroke (via keypad, digital pressure display) - Travel measurement system right and left via rotary encoders - Electrical control: MS-DOS PC with Ageo H v2.23 control software - Operator panel with swiveling display - Stroke movement and press force adjustable via joystick - Adjacent hydraulic power unit with electrical cabinet - Hydraulic draw cushion under the press table - Draw cushion with ejector function - Continuous stroke control - Floor-level installation - Electrical oil temperature monitoring - Operating manual with circuit diagrams Space required by press (upright) L x W x H: 1800 x 1010 x 3470 mm Space required for horizontal transport L x W x H: 3500 x 1800 x 1200 mm Net weight press: 13 tons Space for hydraulic power unit L x W x H: 1000 x 800 x 3040 mm Net weight hydraulic power unit: approx. 1 ton The machine was used as a tool trial press in a toolmaking workshop. Very good condition.

Year of construction: 1992, condition: used, machine/vehicle number: 207320; Lg-Nr. 09361, Technical data: - max. working length 1250 mm - bar passage 1050 mm - max pressing force 80 t - stroke 250 mm - bar overhang 300 mm - max. installation height between table and press beam 560 mm - lifting speeds - down speed idle max 100 mm/sec. - Up speed 100 mm/sec - Pressing speed max. 12 mm/sec. Dkjdpfeb Rk Ekjx Afzou - Total drive power 15 kW - space requirement approx. W 1750 x H 3400 x D 2000 mm - Weight approx. 8500 kg - with: - CNC - control CYBELEC DNC 7400 PSGY - controlled X - axis back gauge 5 - 1000 mm - Z - axis pneum. height adjustable in three steps - manually movable and foldable stop fingers - controlled pneumatic die displacement - hydr. tool clamping - manual crowning - 2 pieces support arms - sharpening tool divided H 320 x L 1000 mm - deer foot tool H 320 mm x L 1000 mm - universal die L 1000 mm

Condition: new, Technical data: Capacity: 160 t Installation height: 1100 mm working area, max.: 1100 x 350 mm piston stroke: 400 mm forward speed: 6,2 mm/s return speed: 6,8 mm/s motor power: 5,5 kW width: 1640 mm depth: 1000 mm height: 2550 mm Weight, approx.: 1300 kg Equipment: - Laterally displaceable cylinder via rack, pinion and handwheel - Generous working area - Height adjustable table - Torsion-resistant design with welded steel Dksdpfx Afek Nz Ntszeu - Pressure gauge - Fine pressure adjustment - Additional hand pump

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, total height: 27,500 mm, total width: 10,500 mm, total length: 16,500 mm, pressing force: 25 t, table width: 630 mm, table length: 500 mm, operating speed: 100 mm/s, overall weight: 2,200 kg, reverse speed: 450 mm/s, ram plate width: 450 mm, ram plate length: 360 mm, ram stroke: 500 mm, die cushion stroke: 160 mm, clearance between the columns: 800 mm, power: 8.75 kW (11.90 HP), Hydraulic press PYE 25 S1M. Year of manufacture: 1990. Manufacturer: VEB Wema Zeulenroda (Germany). Specifications: Maximum pressing force: 25 tons. Operating pressure: 16 MPa. Upper table: 450 x 360 mm. Lower table: 630 x 500 mm. Clear opening: 800 mm. Cylinder stroke: 500 mm. Dkodpfstzwxdsx Afzsu Downward speed: 100 mm/sec. Upward speed: 450 mm/sec. Power requirement: 8.75 kW. Weight: 2200 kg. Height: 2750 mm, Length: 1650 mm, Width: 1050 mm. Machine is in very good technical condition. Fully overhauled. Inspection and test run under power possible on site.

Condition: good (used), pressure 250 t passage width 700 mm stroke 850 mm table surface area 2000 x 1000 mm mould height - Max./min. 355 / 1200 mm Dsdpfsxcblwex Afzeku total power requirement 30 kW weight of the machine ca. 25 t dimensions of the machine ca. 4,2 x 2,1 x 5,5 m

Condition: excellent (used), I sell a Lukas baler in very good condition. Djdpsum Htzsfx Afzoku

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders Dkodpfjvq Rtksx Afzju - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Year of construction: 2001, condition: good (used), Offer 20202 Technical data: - max. pressing force 35 t Dkedpfxop Dt Tao Afzou - projection to the center of the ram 240 mm - working height adjustable with hand crank 540 to 940 mm - 2 hand controls - protective screen enclosure with light barrier - material - insertion device - pneumatic connection - Press control via SIEMENS SIMATEC OP 7 - drive 400 V / 15,5 kW - Space requirement approx. W 1200 x H 2000 x D 2400 mm - Weight approx. 2500 kg

Condition: new, Technical data: Capacity: 100 t Installation height: 1010 mm working area, max.: 1010 x 300 mm piston stroke: 400 mm Dsdpfx Afek Nz N Ejzjku forward speed: 7,12 mm/s return speed: 13,42 mm/s motor power: 4 kW width: 1600 mm depth: 850 mm height: 2450 mm Weight, approx.: 1000 kg Equipment: - Laterally movable cylinder - Generous working area - Height adjustable table - Torsion-resistant design with welded steel - Pressure gauge - Fine pressure adjustment - Additional hand pump

Condition: ready for operation (used), Year of construction: 2000, functionality: fully functional, machine/vehicle number: 65056, pressing force: 5,000 t, table width: 4,520 mm, table length: 2,150 mm, overall weight: 319,000 kg, ram stroke: 900 mm, Equipment: safety light barrier, Pressure build-up time: 3.6 s Pressure relief time: 1.5 s 6-axis industrial robot, manuf. ABB, type IRB6640 M2004 Control cabinet array, 12-door, SN 6/5056 Operator panel, water-based hydraulic unit Djdjxb Tplepfx Afzjku Tool change device Mesh safety enclosure with light curtains

Condition: good (used), functionality: fully functional, Year of construction: 1990, Press force: 250 t Bending length: 4000 mm Distance between uprights: 3000 mm Control: Cybelec ModEva RA Machine weight approx.: 22,000 kg Space requirement approx.: 4300x2700x3400 mm Equipment / accessories: Dedpfxjxb Tifo Afzjku - 2 bend supports in front of the machine - Control system retrofit to CYBELEC ModEva 15T - Two-person operation - Upper and lower tools - Die shifting - Crowning system - 2 bend supports - Controlled axes: y1, y2, x, R, z1, z2 - Tool clamping top and bottom

Condition: ready for operation (used), Year of construction: 2012, General Data Machine weight 7500 This SCHAAL SEP63N was manufactured in 2012. It is a robust hydraulic stamping press with a nominal force of 630 kN and a stroke length range of 8-80 mm. It supports tool dimensions up to 710 x 710 mm and operates at a flywheel speed of up to 500 rpm. Power consumption stands at 130 kW, and it requires a 400 V operating voltage. Consider the opportunity to buy this SCHAAL SEP63N hydraulic stamping press. Contact us for more information. Dsdoxb E Itspfx Afzoku Application Types Stamping

Condition: used, Hydr. spotting press MILLUTENSIL type BV 25 PM Machine. No. 632 / 25111 Year of construction 1991 Closing force 18 ton. Dkodpfx Afstx E Rdozou Opening force 15 ton. Table surface 775 x 760 mm Clamping surface of the upper table 900 x 550 mm Frame width 900 mm Installation height max. 750 mm Installation height min. 230 mm Stroke of the upper table 520 mm Lifting speed infinitely variable 0 - 1000 mm/min. Hydraulic pressure adjustable 10 - 200 bar Tool weight on the table max. 2500 kg Tool weight on the upper table max. 800 kg Table height above floor 850 mm Motor power 4 kW Mains connection 380 Volt, 50 Hz - Upper table can be swiveled 360° by motor - Hydraulic ejector unit in the table with 120 mm stroke - M 14 threaded holes in the table - Hydraulically extendable table - Depth adjustment bar for automatic downward stroke limitation Space requirement L x W x H 1550 x 1500 x 2000 mm Weight 1900 kg

Condition: good (used), Year of construction: 1988, machine/vehicle number: 053-019/35, Offer 24591 Technical specifications: - Maximum press force 25 t - Maximum ram stroke 500 mm - Stroke speed 0 - 40 mm/s - Return stroke 0 - 200 m/min - Installation height 800 mm - Throat to ram center 360 mm - Ram clamping area 440 x 360 mm - Ram clamping pin 40 mm - Table size 630 x 500 mm - Table height above floor 710 mm - Deep drawing force 10 t - Maximum deep drawing depth 160 mm Dkodpswd Nybsfx Afzsu - Drive 400 V / 4 kW - Space requirement approx. W 800 x H 2720 x D 1150 mm - Weight approx. 2500 kg

Condition: new, Technical data: Capacity: 60 t Installation height: 820 mm Working area, max.: 820 x 300 mm Piston stroke: 400 mm Forward speed: 6.1 mm/s Return speed: 10 mm/s Motor power: 3 kW Dkedpjk Nz Ndsfx Afzeu Width: 1460 mm Depth: 850 mm Height: 2400 mm Weight, approx.: 700 kg Equipment: - Laterally movable cylinder - Generous working area - Height-adjustable table - Torsion-resistant design made of welded steel - Pressure gauge - Fine pressure adjustment - Additional hand pump

Condition: good (used), Manufacturer: MÜLLER Tip: SDZ 63t Table surface: 620x500mm Pressure: 63 t Dedpjn D Eiasfx Afzeku

Condition: good (used), functionality: fully functional, Year of construction: 1994, Pressure: 160 t Bending length: 3,200 mm Control unit: CYBELEC CybTouch 15 PS Dedpfx Asxb Sm Nefzoku Machine weight approx.: 14,000 kg Accessories/Equipment: - Control unit retrofit March 2025 – CYBELEC CybTouch 15 - Foot switch - Tools

Condition: like new (used), Year of construction: 2023, functionality: fully functional, pressing force: 40 t, table width: 1,500 mm, table length: 1,000 mm, reverse speed: 10 mm/s, ram plate width: 1,500 mm, ram plate length: 1,000 mm, type of input current: AC, travel distance X-axis: 1,200 mm, power: 9 kW (12.24 HP), Equipment: safety light barrier, If the press does not exactly meet your requirements, please click here to request a customized quotation tailored to your needs: HIDROBRASIL manufactures presses to your exact specifications at surprisingly competitive prices! ##### Mould opener-closer with 40 tons pressing force Table and ram size: 1500 x 1000 mm for heated tools Technical data: Pressing force: 40 tons Maximum open height: 1800 mm Ram travel: 1500 mm Oil temperature monitoring: Electric air cooling Lubrication: Manual via grease nipple Travel of the extending table: 1200 mm Speed of the extending table: 30 mm/sec. Electrically steplessly rotatable ram: 180 degrees T-slots: According to customer requirements Pressure setting: From 10 tons to 40 tons Monitor: 10" on the control cabinet for pressure setting and warning messages Two-hand operation Dsdstwmp Sspfx Afzsku Special features: Insulation of the clamping plates towards the ram: With resin insulation plate and special ventilation plate Hydraulic system: With BOSCHREXROTHPARKERATOS components Safety components: From SICK Control system: SIEMENS Remote maintenance unit: SECOMEA - Ethernet Installation and operating conditions: Maximum ambient temperature: 40 °C Height above floor (overall height): Approx. 3800 mm Total weight of the press without operating materials: Approx. 13 tons This machine is supplied in the colors requested by the customer and complies with all EU legal requirements and standards. ##### Are you looking for a customized machine? Contact us for a customized offer.

Condition: used, Single-column pneumatic press, hydraulic press PAUL ANTON type PVT 2 Pneumatic table press, embossing press Dodetrpiispfx Afzoku No. 97148 Year of manufacture approx. 1980 Compressive force: 10 ton throat depth: 100 mm Ram stroke: approx. 25 mm Plunger surface: Ø 32 mm Table size: 250 x 220 mm Table opening: 53 x 53 mm Table height: 1060 mm Installation height: 155 mm - Very stable construction - Hydro-pneumatic press with air to oil pressure ratio - Pneumatic foot switch - ram with M12 internal thread - Metal base Space requirement L x W x H 850 x 620 x 1560 mm Weight approx. 200 kg good condition

Condition: good (used), Year of construction: 1986, machine/vehicle number: 025-012-44, Offer 24088 Technical specifications approx.: - Max. press force 40 t - Max. ram stroke 500 mm - Stroke speed 0 - 6 m/min - Return stroke 0 - 27 m/min - Installation height 800 mm - Throat to ram center 360 mm - Ram clamping area 500 x 400 mm - Ram clamping pin 40 mm - Table size 700 x 500 mm - Table bore / opening 180 mm - Table height above floor 700 mm Dkjdpfewl D Upsx Afzeu - Oil capacity approx. 300 liters - Drive 400 V / 13 kW - Space requirement approx. W 1250 x H 2950 x D 1800 mm - Weight approx. 3300 kg - With: - Two-hand operation

Condition: new, Technical data: Capacity: 200 t Installation height: 900 mm Working area, max.: 1300 x 450 mm Piston stroke: 400 mm Forward speed: 6.4 mm/s Return speed: 11.04 mm/s Motor power: 7.5 kW Width: 2100 mm Depth: 1200 mm Height: 2850 mm Weight, approx.: 2600 kg Equipment: - Laterally movable cylinder via rack, pinion and handwheel - Generous working area - Height-adjustable table - Torsion-resistant design with welded steel - Pressure gauge - Fine pressure adjustment - Additional hand pump Your advantages: - One of the heaviest versions on the market - Available with tonnages of up to 500 tons - Maximum performance and stability - Different upright widths available on request - Horizontally freely positionable hydraulic cylinder, handwheel, rack and pinion (from 160 tons) Dedpopl T Diofx Afzeku Available with special equipment: - Fine pressure adjustment - SPS control - Working plate with T-slots for fixing irregularly shaped components - Lateral hydraulic cylinder adjustment

Condition: used, Double column hydraulic press RASTER ZEULENRODA (WALTER) type WUP S 60 Machine. No. 136 / 7 (156-165) Year of construction 1999 Basic machine built in 1987, completely overhauled in 1999 with new control system Pressure capacity 60 ton. Stand width 1090 mm Dksdeuicg Uopfx Afzeu Lateral column passage 265 mm (one-sided) Ram area 650 x 300 mm Additional plate on ram 990 x 550 x 60 mm Table surface 990 x 550 mm Plunger stroke max. 320 mm Installation height 330 or 390 mm Table height above floor 980 mm Hydraulic operating pressure 320 bar Rapid traverse downwards 75 mm/s Rapid traverse upwards 100 mm/s Working speed 17 mm/s Return speed 33 mm/s Motor power 15 kW (2x 7.5 KW) Mains connection 400 Volt, 50 Hz, 15.5 kW - Press safety control PILZ PSS 3056-1 + PXT 305 Com-LC - Manually adjustable limit switch cams for stroke limitation - 2-hand operation and electric foot switch - Press force adjustment via handwheel - ram plate additionally guided by 2 lateral guide rods, Ø 50 mm - Table top with 18 mm T-slots, slot spacing 175 mm - Through-hole table top Ø 100 with insert reduction to Ø 30 mm - Plunger plate with 18 mm T-slots, slot spacing 150 mm - Additional ram plate without fastening grooves - Electrical cabinet on the side of the machine stand - Electrical circuit diagram - 2 monitored safety valves for the hydraulics - UVV for manual insertion work Space requirement L x W x H 1950 x 1000 x 2700 mm Weight 2.6 tons good condition

Condition: new, Powerful hydraulic workshop press with movable cylinder (via handwheel), ideal for large and heavy workpieces. Picture shows WHP 160 Technical data: Capacity: 250 t Installation height: 900 mm Working area, max.: 1300 x 450 mm Piston stroke: 400 mm Forward speed: 8.58 mm/s Return speed: 13.03 mm/s Motor power: 15 kW Width: 2450 mm Djdpfop Dt Uusx Afzjku Depth: 1200 mm Height: 2650 mm Weight, approx.: 3100 kg Equipment: - Laterally movable cylinder via rack, pinion and handwheel - Generous working area - Height-adjustable table - Torsion-resistant design with welded steel - Pressure gauge - Fine pressure adjustment - Additional hand pump Your advantages: - One of the heaviest versions on the market - Available with tonnages of up to 500 tons - Maximum performance and stability - Different upright widths available on request - Horizontally freely positionable hydraulic cylinder, handwheel, rack and pinion (from 160 tons) Available with special equipment: - Fine pressure adjustment - SPS control - Working plate with T-slots for fixing irregularly shaped components - Lateral hydraulic cylinder adjustment

Condition: used, Single-column hydraulic press, straightening press, punching frame ECKOLD Press frame with hydraulic cylinder, mobile press, punching unit Type RSD 1500 - 125 Machine. No. 317 / 690 Year of construction approx. 1986 Compressive force 150 ton. throat 125 mm Dodpjd Swtasfx Afzsku ram stroke 35 mm Table size 280 x 210 mm Plunger surface Ø 125 mm Installation height (ram to table) max. 265 mm Table height above floor 403 mm Hydraulic operating pressure max. 500 bar - without hydraulic unit - Plunger surface with 4 M16 threads and 20 mm guide groove, central centering hole Ø 15 mm - 1 high-pressure hydraulic hose with external thread M30x1.5 mm, hose length 4 meters - 1 high-pressure hydraulic hose with union nut M30x1.5 mm, hose length 4 meters Space requirement L x W x H 700 x 300 x 1450 mm Weight 1250 kg Good condition

Condition: used, Hydraulic punch, punch frame for use with JOKA punching units type HP-S Hydraulic hole punch, hydraulic press for punching brackets Year of manufacture: approx. 1995 Pressing force: 5 tons Throat depth: 155 mm Stroke: approx. 20 mm Punching unit width: max. 54 mm Punching unit installation height: max. 220 mm Die holder: Ø 48 mm Motor output: 1.5 kW Power supply: 230 Volt, 50 Hz Dkodpfx Afsltrmuszju - Suitable for universal use with JOKA SW 20 or SWD 20 punching units - Throat depth of punching units can be larger, can be pushed through to the rear - Stroke release via electric two-hand control - Hydraulic power pack HAWE, type HCW 4 / 2.5-B 1/400-1 - On subframe, mobile Required space (L x W x H): 1100 x 800 x 1450 mm Weight: approx. 200 kg Good condition