Used Weiler Commodor 230 for sale (175)

Condition: good (used), Year of construction: 1996, functionality: fully functional, Description: The machine is in good technical condition and can be tested by prior arrangement. Lathe WEILER Praktikant 160 AC, year of manufacture 1996, serial number 4057. Swing over bed: 320 mm Distance between centers: 650 mm Swing over cross slide: 160 mm Spindle bore: 35 mm Kwodpox H Iddjfx Ad Nst Speed: 48 – 2,500 rpm Power: 4 kW Dimensions: 500 x 1240 x 1550 mm Weight: 680 kg

Condition: ready for operation (used), Distance between centers: 500mm, center height: 140mm, turning diameter over bed/cross slide: 295mm/155mm, spindle bore: 36mm, speed: 3550rpm, tailstock taper: MK3. Machine dimensions X/Y/Z: approx. 1500mm/800mm/1250mm, weight: approx. 700kg. On site inspection is possible. Kjdpfxex Hz Rqo Ad Njwt

Condition: ready for operation (used), A conventional precision lathe Weiler is available. Distance between centers: 650mm, center height: 160mm, swing diameter over bed/faceplate: 320mm/190mm, spindle bore: 43mm, speed: 2500rpm, quill diameter: 40mm, quill travel: 85mm. Machine dimensions X/Y/Z: approx. 1800mm/900mm/1600mm, weight: approx. 1050kg. An on-site inspection is possible. Kwedpfx Aox Hz N Hed Njt

Year of construction: 1986, condition: used, Weiler Primus lathe year ca.1986, three-jaw chuck , Multifix. Machine in a good condition , By arrangement under power ready for demonstration. Kedpfen Ard Dsx Ad Newt

Condition: excellent (used), Year of construction: 2006, Centre height: 160 mm Centre distance: 650 mm Spindle speed: 2,500 min-1 Multifix Kodpfxew Sn Ire Ad Newt Tailstock Accessories

Condition: refurbished (used), Year of construction: 2007, Universal lead and feed spindle lathe Make: WEILER Model: Primus VC Year of manufacture: 2007 - overhauled newly painted RAL 7035 light gray Mach. no.: CK17 Center height: 140 mm Center width: 500 mm Spindle bore: 40 mm with guarantee geometric acceptance with test report Accessories: - 3-A digital display SIEMENS - Chuck protection hood with electrical protection - Drive motor braked - Quick-change tool holder base body size A Kjdpov D Ip Nsfx Ad Newt - Bed stop - Covered lead and feed spindle - Chip rear wall - Pull-out chip tray - Operating instructions - Used, as seen -

Condition: reconditioned (used), Year of construction: 1990, Universal lead and feed spindle lathe Make: WEILER Model: Praktikum 160 B Year of manufacture: 1990 - overhauled newly painted RAL 7035 light gray Mach. no.: 90-160-2054 Center height: 160 mm Center width: 650 mm Kwodpfx Aohy Tdysd Net geometric acceptance with test report Accessories: - 3-axis digital display FAGOR Innova 30i T - covered lead and feed spindle - braked drive motor - coolant system - electrically secured chuck protection hood - quick-change tool holder size A - simple bed stop - chip back wall - operating instructions with guarantee used as seen The machine is technically corresponding to the state of the year it was built.

Condition: reconditioned (used), Year of construction: 1989, Universal lead and spindle lathe Make: WEILER Model: Condor B Year of manufacture: 1989 - overhauled newly painted RAL 7035 light gray Mach. No.: 1401 with guarantee Kwsdog R S Rcspfx Ad Njt Accessories: - 3-A digital display FAGOR Innova 30i T, new - Chuck protection hood with electrical fuse, new - Quick-change tool holder base body size B - Bed stop - Coolant device - Chip back wall - Operating instructions -used, as seen -

Condition: excellent (used), Weiler Ergodor lathe Max. Turning diameter over bed: approx. 320 mm Max. Turning diameter over support: approx. 160 mm Kwsdpjq Ixxyofx Ad Nst Max. Turning length: approx. 470 mm Bar passage: approx. 36 mm Spindle: Speed range: approx. 30 - 3550 rpm Spindle nose: A 2 - 5 Drive power: approx. 3.0 kW Automatic longitudinal & face feeds: Feed range: approx. 0.020 - 2.0 mm/rev Suitable for threads: - metric 0.20 - 12 mm Inch 80 - 2 Gg/ Diametral - Pitch thread 160 - 5.5 Dp Module 0.1 - 4

Condition: good (used), Year of construction: 2000, functionality: fully functional, turning diameter over cross slide: 180 mm, spindle bore: 40 mm, turning diameter: 330 mm, turning diameter over bed slide: 330 mm, center height: 165 mm, turning length: 750 mm, quill stroke: 110 mm, rotational speed (max.): 2,800 rpm, rotational speed (min.): 22 rpm, power: 5.5 kW (7.48 HP), Equipment: rotational speed infinitely variable, Weiler Condor AC stepless rotary machine Ksdpfx Aoruqzcod Nowt

Condition: refurbished (used), The lathe was completely overhauled in 2025: the bed and guides were reground, the machine was fully stripped of paint and powder-coated, everything was disassembled, cleaned, and rebuilt. Finally, the machine was measured and a protocol was created. Extensive accessories are included (13 pcs. Multifix, many replacement jaws, etc.). The original documentation with manual and maintenance reports is available! Kwodpfx Asx D Ayled Not

Condition: like new (used), Year of construction: 1992, Lathe WEILER Precision center lathe in ergonomic design The Weiler Ergodor is the first German ergonomically designed lathe. It creates a more humane workplace and prevents health problems. The key feature is that the employee can operate this lathe while standing or sitting. Technical data Center width 470 mm Turning length 430 mm Center height 145 mm Rotation Ø over cross slide 160 mm Rotation Ø over bed 300 mm Spindle head, short taper flange Bayonet mounting DIN 55022 size 5 or Camlock clamping D 1-ASA-4 Spindle bore 36 mm Kwedpfxovgqu He Ad Net DIN 55022 size 5 Spindle inner taper Spindle speeds Speeds 30 - 3550 rpm S Speeds 15 - 3550 rpm Brake motor 3 kW Brake motor 1.5/3 kW Face slide travel 150 mm Travel of the top slide 100 mm Feed rates and thread pitches on the gearbox switchable steps 30 Section 2 1.5/3 kW 38 Gear ratio in headstock 3 20 Long feeds 150 mm via change gears 100 mm via toothed belt Face feeds = 1/2 Longitudinal feed values Metric pitches 0.2 - 12 mm Module pitches 0.1 - 4 Dimensions 1450 x 640 x 1500 mm Dimensions 1450 x 640 x 1500 mm Net weight 1000 kg Acceptance according to toolmaker's accuracy DIN 8605 20 Built according to the rules of occupational safety, official test no. A. EM 11 1545/80. Encombrement 1450 x 640 x 1500 mm

Condition: good (used), Year of construction: 1991, Machine type Lathe - cycle-controlled Manufacturer WEILER Type E30 year of construction 1991 Control Weiler Country of origin Germany Additional information Cycle-controlled lathe WEILER - E30 Technical details Turning diameter max. 330 mm Turning length 750 mm Weiler control Center height 165 mm Swing diameter over bed 330 mm Max. turning diameter over facing slide 160 mm Face slide travel 180 mm Longitudinal bed slide travel 395 mm Main spindle: Speed range - main spindle 1 - 4,500 min/-1 Drive power - main spindle 9 / 11 kW Max. Torque 165 Nm Spindle head DIN 55027 / 5 Spindle diameter in front bearing 70 mm Spindle bore 40 mm Usable bar diameter ( - ) mm Tool holder: Type MultiFix Turning tool shank cross-section 20 x 20 mm Kodpfxsr Dvqze Ad Njwt Tailstock: Quill stroke 110 mm Quill diameter 50 mm Tailstock holder MK 3 Feed rates: Rapid traverse max. 10 m/min Feed force 6 / 3 kN Feed range 0 - 20 mm/-1 Thread cutting: metric 0.1 - 400 mm Inch 1/4 - 56 G/1" Module 0.125 - 28 mm.II DP 1 - 224 G/".II Number of threads max. 50 Total power requirement 10 kVA Machine weight approx. 1.5 t Space requirement approx. 2.8 x 2.0 x 2.0 m

Condition: good (used), Lead and feed screw lathe WEILER PRAKTIKANT 800 R Kodpfx Adjx A Ukts Newt - Swing diameter over bed: 300 mm - Swing diameter over cross slide: 150 mm - Turning length: 800 mm - Spindle bore: 42 mm - Speed range: 40 - 2000 rpm - Automatic longitudinal / cross feeds - Thread cutting / metric / inch etc. - Tailstock Morse taper 3 - Three-jaw chuck - Chip guard rear wall + work light - Chip tray - Change gears - Tool cabinet - Documentation Dimensions: LxWxH 1.8x0.8x1.6 meters / Weight 750 kg Errors and input mistakes excepted

Condition: good (used), Leadscrew & feed rod lathe WEILER CONDOR - Original paint - Centre height: 165 mm - Swing over bed: 330 mm - Swing over cross slide: 170 mm - Distance between centres: 800 mm - Spindle speeds: 24 - 2800 rpm - Automatic longitudinal/cross feeds - Spindle bore: 38 mm - Tailstock MT 3 - Collet chuck system + 17x collets - Three-jaw chuck - Multifix toolpost with inserts - Electric chuck guard - Chip guard rear panel - Work lamp - Various accessories - Documentation Dimensions: LxWxH 1.8x0.9x1.6 m / Weight 800 kg Errors and omissions excepted. Kwodpfjx A D Ubjx Ad Net

Condition: good (used), Centre distance: 450 mm Centre height: 120 mm Spindle bore: 23 mm Speed: 40 – 3000 rpm Infinitely variable drive with 3 gearbox stages and digital speed display Tailstock: MT 2 Drive power: 1.5 kW Weight: 350 kg Dimensions: 1200 x 650 x 1330 mm Paint: Reseda green RAL 6011 Digital display: Optional at extra cost Accessories: Further accessories available on request Ksdow I A Uxepfx Ad Njwt

Condition: reconditioned (used), Year of construction: 1977, Engine Lathe Brand: WEILER Model: MDU 260 Year of manufacture: 1977 – workshop tested Machine no.: 14942 Centre height: 125 mm Spindle bore: 28 mm Kwsdpfx Adsxv A I Te Njt Accessories: - Electrically operated chuck guard - 3-jaw chuck Ø 140 mm incl. set of turning jaws incl. set of boring jaws - 4-jaw chuck Ø 140 mm incl. set of turning jaws incl. set of boring jaws - Safety chuck key - Manual clamping device - Collet set W28 (366E) - Set (25 pcs.) collets W28 (366E) from 1.0-25.0 mm in 1.0 mm steps - Fixed centre for headstock W28 (366E) - Quick-change toolholder Body size A - Operating manual Used as seen, without warranty The machine is technically in accordance with the state of the art of its year of manufacture.

Condition: excellent (used), Swing over bed 330 mm Distance between centers 750 mm Spindle speeds 1-4'500 rpm Control: WEILER C3 Misc. accessories Kjdjud Naqepfx Ad Njwt MARCELS MASCHINEN CH

Condition: excellent (used), functionality: fully functional, Weiler Primus lead and feed screw lathe from training workshop !!! Technical data: >> Year of construction approx. 1985 >> center height 120 mm >> center distance 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm Ksdpfx Asu Aftgjd Newt >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck 160mm with 1 set of jaws >> 1 new three-jaw chuck 125mm with 2 sets of jaws >> Collet chuck device with collets from 1 mm to 20 mm 1 mm increasing >> Mulifix size A with 3 steel holders >> Fence >> Change wheels To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs smoothly even at high speeds. The Primus was used in a training workshop. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus guide and spindle lathe from the training workshop!!! Kjdpevtp Edjfx Ad Nswt Technical data: >> Year of manufacture approx. 1985 Machine no. 1191 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear stages >> Spindle passage 23 mm >> Short taper spindle head KK4 DIN 55027 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm / rev >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 x three-jaw chuck 125 mm with 2 sets of jaws >> Collet device with Collets 18 pieces >> Mulifix size A with 3 steel holders >> Stop >> Electric spindle protection About the machine: A Weiler Primus guide and pull spindle lathe is offered in very good condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The Weiler runs quietly even at high speeds. The Primus was in a training workshop. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site with power on and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus GS lead and feed screw lathe 3 axis digital readout Easson- ES8 from training workshop Super condition !!! Technical data: >> Year of construction approx. 1990 Machine no. 3768 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> Spindle clearance 23 mm >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 3-axis digital display from Easson ES8 >> collet chuck device from 1 to 20 mm collets 1 mm rising with holder and draw tube Ksdpfx Aevkfhpjd Nowt >> 1 three-jaw chuck with 2 sets of jaws >> 1 four-jaw chuck with 2 sets of jaws >> Mulifix size A with 3 steel holders >> Bed stop >> Turning device To the machine : We are offering a Weiler Primus lathe built around 1990 in excellent condition. The machine is of course fully functional. The slides all run very smoothly and evenly. The bed guides are in very good condition. The Weiler runs smoothly even at high speeds. The machine comes from a training workshop of a large company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see for yourself its condition.

Condition: excellent (used), functionality: fully functional, Weiler Primus LZ/G lead and feed screw lathe in special paint finish light gray !!! Technical data: >> Year of construction ca.1990 Machine-No.3150 >> Center height 120 mm >> Center width 430 mm >> Speed: 60 - 3000 rpm in 18 gear steps >> spindle passage 23 mm Kwedpfx Aovivmysd Not >> Short taper spindle head DIN 4 >> Tailstock MK 2 >> Feed rates from 0.03 to 0.15 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.25 to 2.5 mm >> Switchable spindle brake >> Weight approx. 360 kg >> Length 1.2 m, height 1.3 m, depth 0.65 m Accessories and equipment: >> 1 piece three-jaw chuck NEW 125mm with 2 sets of jaws >> Mulifix size A with 2 steel holders >> collet chuck device new with collets from 3 to 26mm 1 mm increasing new >> To the machine : We are offering a Weiler Primus lathe in very good condition. The machine is of course fully functional. The slides all run smoothly and evenly. The bed guides are in very good condition. The Primus was used in a training company. This newer generation of Weiler lathes is very user-friendly and surfaces can be produced as if ground. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, Weiler precision lathe model Condor B, lead and feed screw lathe with brand new K&C 3-axis digital readout, CE compliant! Technical data: >> Machine No. 2442, year of manufacture 1997 >> Centre height: 165 mm >> Centre distance: 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore: 40 mm >> Camlock spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock: MT 3 >> Feeds: from 0.015 to 0.46 mm/rev >> Thread cutting: metric, imperial, module and diametral pitch threads possible >> Metric thread pitches: 0.18 to 28 mm >> Weight: approx. 1100 kg >> Spindle brake, selectable >> Length: 1.83 m, height: 1.29 m, depth: 0.88 m Equipment and features: >> New K&C 3-axis digital readout, 12-month manufacturer's warranty, supplied with operating manual Features: mm/inch switching, selectable ABS/INC coordinates, value halving function, reference mark, tool memory for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 x brand new 160 mm 3-jaw chuck with 2 sets of jaws >> 1 x 200 mm 4-jaw chuck with 1 set of jaws >> New collet chuck system and new collets from 3 to 25 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear splash guard >> Machine feet Safety features: electronic spindle guard, 2 emergency stop buttons, changewheel box with safety interlock, spindle brake About the machine: Offered here is a Weiler Condor in very good condition. The machine is, of course, fully functional. A very robust and powerful machine. The new K&C 3-axis digital readout makes work easier and more precise. The machine has been electrically and mechanically checked by us. A complete oil change has been carried out. This newer generation of Weiler lathes is very user-friendly. Take advantage of the opportunity to inspect and test this machine under power on site. Ksdpsxcuazjfx Ad Nowt

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Weiler Primus VC Precision Centre Lathe 3-axis Digital Readout K&C NEW with VC Drive, Stepless Speed Adjustment, and CE Compliance, Very Good Condition Technical Data: >> Year of manufacture: 2003, Machine No. 646 >> Centre height: 140 mm >> Centre distance: 500 mm >> Spindle speeds: up to 4000 rpm, stepless >> Spindle bore: 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock Morse taper 3 >> Feeds: from 0.02 to 0.63 mm/rev >> Thread types: Metric, Inch, Module, and Diametral Pitch >> Metric thread pitches: from 0.25 to 8 mm Kedpfx Aew Idllsd Newt >> Weight: approx. 800 kg >> Spindle brake can be activated >> Machine dimensions approx. 1.4 m x 1.55 m x 0.95 m Accessories and Equipment: >> 3-axis Digital Readout K&C NEW >> Collet chuck system with collets from 3 to 26 mm, new, 1 mm increments, NEW >> 160 mm 3-jaw chuck with 2 sets of jaws >> Multifix size A with 2 toolholders >> Electric chip guard >> Machine feet >> Splash guard About the Machine: This offer is for a Weiler Primus VC lead and feed screw lathe, built in 2003 and in very good original condition. A very nice lathe with VC drive and stepless spindle speed control. The digital readout and scales from K&C are new. This newer generation of Weiler lathes is very user-friendly and can produce ground-like surface finishes. The K&C digital readout makes operation even easier and more precise. Take the opportunity to inspect this machine under power on site and be convinced of its condition.

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Weiler Precision Lathe Model Condor 81 Lead and Feed Spindle Lathe with 3-Axis Digital Display from K&C NEW Technical Data: >> Year of manufacture 1987 Machine No. 87 835 >> Center height 165 mm >> Center distance 750 mm >> Spindle speeds: from 22 to 2800 rpm >> Spindle bore 40 mm >> Short taper spindle nose DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feeds from 0.015 to 0.46 mm/rev >> Possible threads: Metric, Inch, Module, and Diametral-Pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake switchable >> Length 1.83 m, Height 1.29 m, Depth 0.88 m Accessories and Equipment: >> 3-axis digital display from K&C new, 12 months manufacturer's warranty with operating manual Functions: Switch mm/inch, coordinate selection ABS/INC, halving of display value, reference mark, tool programming 200 pcs, taper calculation, radius/diameter, quick zeroing, reversing of count direction >> 1 piece 3-jaw chuck 160 mm NEW, 2 sets of jaws >> 1 piece 4-jaw chuck 160 mm, 1 set of jaws Kodpfx Aewrmuxsd Nswt >> Collet equipment and new collets from 3 to 26 mm in 1 mm increments >> Multifix size B with 2 tool holders >> Bed stop >> Electronic spindle guard >> Rear panel >> Coolant system >> Machine feet About the Machine: A used Weiler Condor 81 in very good condition is offered. The machine is, of course, fully functional and has been completely disassembled and repainted. A very robust and powerful machine. The new 3-axis digital display from K&C makes working even easier and more precise. The machine has been electrically and mechanically tested by us. A complete oil change was carried out. This newer generation of Weiler lathes is very user-friendly. Take the opportunity to view and test this machine on site under power.