Used Weiler 260 for sale (206)

Condition: good (used), used -- 6-fold changer for WEILER , type 260 Laodpfx Abjxdixnj Ujh

Year of construction: 1977, condition: ready for operation (used), A Weiler precision lathe, overhauled by Mammut in 2004, is available. Center height: 125mm, max. swing over bed/cross slide: 260mm/140mm, distance between centers: 500mm, spindle bore: 28mm, clamping range: 1mm-26mm, drilling diameter: 22mm, cutting edge height: 22mm, tailstock quill diameter: 80mm, tailstock quill travel: 80mm, tailstock offset: 450mm. Documentation available. An on-site inspection is possible. Ljdpjxqqmtofx Ab Usah

Condition: good (used), Year of construction: 1998,

Condition: used, Technical data : Center width approx. 500 mm Center height above bed 125 mm 16 speeds from 125 - 2800 rpm Space requirement, length x width 1.2 x 0.6 m Estimated weight approx. 450 kg . Lsdpfx Aowrahxsb Usah Scope of delivery : Hand lever quick clamping device Electrical monitoring of whether the part clamping lever is in the open or clamped position 1 set of collets from 3.0 - 25.0 mm, increasing by 1 mm Cross support with two tool holders Turret with 6 tool holders .

Condition: used, Year of construction: 1970, Weiler lathe with tailstock Ledpfx Abohtnu Ts Ujah

Year of construction: 1973, condition: excellent (used), turning length 125 mm Laedoxpxqwjpfx Ab Uoh weight of the machine ca. 0,4 t

Condition: used, turning diameter over bed 260 mm turning diameter over slide rest 140 mm turning length 500 mm centre height 125 mm bed width 160 mm spindle turning speed range 16: 110-3600 U/min spindle bore 28 mm face slide travel 120 mm upper slide-adjustment 120 mm tailstock quill taper MT 2 tailstock quill adjustment 80 mm Ljdpfxjvtthio Ab Uoah drive motor 0,37 / 0,88 kW weight of the machine ca. 350 kg dimensions of the machine ca. 1,3 x 0,6 x 1,2 m Mechanic's lathe with manual feed and spindle support, drive via V-belt and stepped pulleys as well as 2-pole motor, hardened, finely ground work spindle, support adjustment over the entire bed length using eccentric clamping lever, three-jaw chuck, collet device with pliers, crank tailstock, cast base. Machine dealer with own stock of 1600 m².

Condition: used, Year of construction: 1992, machine/vehicle number: 160 3205, Sale only within EU member states! No private sale MAE can be inspected. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tooling, as well as for compliance with all safety and environmental protection safety and environmental protection requirements. Any warranty is excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tools as well as for compliance with all safety- and environmental-requirements, mentioned in the accident prevention regulations, we take over no guarantee. Lodpeuxl Ezofx Ab Uoah

Condition: good (used), WEILER DA 260x1000 Center Lathe Digital Display - Three Axes "NEW" -Center Height 260mm -Turning Diameter Over Bed 535mm -Turning Diameter Over Cross Slide 345mm -Center Width 1000mm -Spindle Bore 71mm -Speed Range 33 - 1500 rpm Lajdpfx Abowiztwj Ush -12 Spindle Speeds via Gearbox -Automatic Longitudinal / Cross Feeds -Threading / Metric / Inch / Diametrical -Tailstock MK 4 -NEW THREE-AXIS DIGITAL DISPLAY -Drive Power 7.5 kW -Face Spindle Nut "NEW" -Multifix Base Holder with Insert -Three-Jaw Chuck 350mm -2 Emergency Stops -Electric Chuck Guard "NEW" -Chip removal panel -Coolant system -Drill chuck -Documentation Dimensions: LxWxH 2.7 x 1.5 x 1.7 meters / Weight 1700 kg Subject to errors and omissions

Condition: ready for operation (used), operating hours: 33,600 h, functionality: fully functional, spindle bore: 83 mm, center width: 2,000 mm, turning diameter over bed slide: 570 mm, spindle speed (max.): 2,500 rpm, controller model: Siemens 810D, No reserve price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Swing diameter over bed: 570 mm Swing diameter over carriage: 340 mm Centre distance: 2,000 mm Speed range, stage 1: 1–625 rpm Speed range, stage 2: 4–2,500 rpm Spindle bore: 83 mm Spindle nose: Size 8 DIN 55027 Feed range longitudinal/cross: 0–20 mm/rev Metric threads: 0.1–400 mm Inch threads: 1/4–56 TPI Tailstock quill diameter: 80 mm Taper: MK 5 MACHINE DETAILS Control: Siemens 810D Electrical data Main drive: 20/17 kW Connected load: 30 kW Dimensions (L x W x H): 4,000 x 2,300 x 1,800 mm Operating hours: 33,600 hours Ljdpfexqpgfex Ab Ujah EQUIPMENT Rapid traverse longitudinal/cross 8-position Sauter tool turret incl. holders Mayfran chip conveyor with coolant system Movable chip guard cover 3-jaw chuck Schunk Rota S 250 Manuals Note: The viewing windows and feed selection levers have been replaced. In addition, an oil change has been performed and the oil filter replaced.

Condition: used, turning diameter 210 mm turning length 1000 mm Laedpfx Abjxqrdys Ujh swing diameter over bed slide 435 mm centre height 210 mm greates pass round over bed 435 mm spindle head DIN 55027 / DIN ISO 702-3 spindle bore 52 mm turning speeds 44 - 2.000 U/min transmission ratio 12 feed per revolution 0,036 - 2 U/mm diameter of quill 65 mm quill stroke 120 mm taper bore DIN 228 MK4 total power requirement 5,5 kW -Lead screw and feed screw cover -Brake for main spindle -Toolmaker precision according to DIN 8605 -High drive power and high torque on the main spindle -Large thread cutting range -Convenient operation -Digital position display (HEIDENHAIN ND 7013) 3-axis display for bed, cross slide, and top slide Tool memory for 16 tools Tool memory with one reference point per axis Sum button for Z and Zo Inch/metric switchable Plane path X as radius or diameter display Display resolution up to 1 µ Taper calculator -LED machine light -Coolant device

Condition: used, Year of construction: 2000, Technical details: turning length: 750 mm turning diameter over bed: 330 mm turning diameter over slide: 160 mm spindle bore: 42 mm turning speed range: 1 bis 4500 U/min drive capacity - spindle motor: 10 kW diameter of quill: 50 mm quill stroke: 130 mm control: Weiler Zyklensteuerung D2 rapid travel - longitudinal/face: 8 m/min weight of the machine ca.: 2100 kg Ljdoxp I E Djpfx Ab Ueah Teach-in lathe, PARAT toolholder basicsystem prepaired for collets 3.chaw-chuck SCHUNK Rota S plus D = 200 mm Yuear of teh Machine 2000, complet retrofitted in 2018 for € 53.000.- Original Invoice exists Control-Update new D2 - V2.07 Machine in very good condition Machine under power *

Year of construction: 2006, condition: ready for operation (used), This Weiler DZ65 was manufactured in 2006. A horizontal turning machine featuring a chip conveyor, counter spindle, extraction system, interface bar feeder, and an in-machine puller for 1m bars. It also boasts an enlarged coolant tank. Consider the opportunity to buy this Weiler DZ65 horizontal turning machine. Contact us for more information. Application Types Turning Ljdpfx Aoxp Sp Hsb Usah

Condition: used, Technical details: turning diameter over bed: 570 mm turning diameter over support: 340 mm turning length: 1000 mm switched on hours: 37917 h centre distance: 1000 mm swing diameter over bed: 570 mm swing diameter over face slide: 340 mm centre height: 280 mm spindle bore: Ø 66 mm revolution per minute: 1 - 625 steples U/min Lajdpfx Abexg Nhne Ush max. torque on the spindle: 1600 Nm longitudinal feeds:: 0 - 20 mm/U cross feed: 0 - 20 mm/U tailstock quill adjustment:: 160 mm tailstock quill: MK 5 mm total power requirement: 20 kW weight of the machine ca.: 3,2 t dimension machine xH: 2,9 x 2,28 x 1,8 m Machine has been overhauled/refurbished: Ball screw Z overhauled, X-axis end position overhauled, new paint job. Conventional design with integrated automatic cycle control. Metric thread cutting, inch threads, DP threads. Chip conveyor not available. 4-jaw chuck with steady rest available. 3-jaw chuck mounted. *

Condition: used, Year of construction: 1997, - Drive system: Teach-in - Centre height [mm]: 210 Lsdpownh I Sefx Ab Ujah - Swing over bed [mm]: 420 - Distance between centres [mm]: 900 - Spindle bore [mm]: 55 - Min. spindle speed [rpm]: 4 - Max. spindle speed [rpm]: 3000 - Options: Digital readout - Type of digital readout: Weiler - Year: 1997 - Documentation available: Yes - CE marking present: Yes - Serial number: 270 - Control: CNC Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: excellent (used), Year of construction: 1992, Weiler Condor 81 Weiler Condor 81 lathe with Heidenhain digital display, year of manufacture 1992, in very good original condition. The machine comes from the training workshop of a renowned German mechanical engineering company. Technical data: Lodow T U Sgspfx Ab Usah Year of manufacture: 2003 Engine lathe WEILER type Condor 81 Distance between centers: 750 mm Swing over bed: 330 mm Center height over bed: 165 mm Swing over cross slide: 180 mm Center height over cross slide: 90 mm Spindle bore: 40 mm Chuck fitting: short taper DIN 55027 size 5 Tailstock quill taper: MK 3 Quill travel: 110 mm Spindle speed: 45 – 2800 rpm, 16 steps Drive power: 3 kW Power supply: 400 Volt, 50 Hz Spindle speeds via 16-speed gearbox Required space (L x W x H): 1850 x 950 x 1400 mm Weight: 1,100 kg Accessories and equipment: Röhm 3-jaw chuck Multifix quick-change toolpost Coolant installation Heidenhain digital readout About the machine: We offer a Weiler Condor 81 lathe with Heidenhain digital display, year 1992, in very good condition. The machine is, of course, fully functional. All slides move very smoothly and evenly. Even at high speeds, the Weiler runs very quietly. This newer generation of lathes is very user-friendly and can achieve ground-like finishes. Take the opportunity to inspect this machine under power at our location and see its condition for yourself. You can find more lathes from renowned manufacturers on our website.

Condition: used, Year of construction: 2014, turning length 650 mm turning diameter 320 mm centre height 160 mm turning dia. over face-slide 190 mm quill: 3 MK spindle bore 42 mm turning speeds 25-5000 U/min centre distance 650 mm Number of working hours 637 h total power requirement 8 kW weight of the machine ca. 1250 kg dimensions of the machine ca. 1,6 x 0,5 x 1,7 m Weiler Praktikant VC Plus lathe, built in 2014, from a test workshop, in excellent condition! Features: All 99 storable tools can be programmed separately with feed rate and speed or constant cutting speed. Separate control of speed and feed rate via Lasdpfx Aboxn Txae Uoh potentiometer is also possible. Thread pitches are freely programmable and feature electronic limit switches. Additional electronic stops can be set for lengths and diameters. A coolant device is not available. 8" colour screen Energy recovery Accessories: The machine includes a quick-clamping device with 30 collets 5 to Dmr 26 mm, 3-jaw chuck made by Röhm including 10 sets of soft jaws,centring tips, tailstock mounts (MK 3) for thread cutting with threaded drills and dies by hand, 15 Multifix holders size A, turning head for Multifix holder for producing bolt circles,spindle and bed stop, tool cabinet with 12 drawers, WP holder for internal and external machining, drills, reamers, standard thread gauges up to M10, comprehensive documentation on operation and maintenance. Translated with (free version)

Condition: used, Year of construction: 2002, Weiler E90 / 4.5M - CNC Lathe with Cycle Automation - Weiler D2 cycle control - Chip conveyor - Approx. 15 pcs. Multifix quick-change toolholders - 1 live centre - Regular servicing by Weiler - Supplied without chuck, without steadies - Year of manufacture: 2002 Technical Data Working Area: - Distance between centres: 4500 mm - Centre height: 450 mm - Swing diameter over bed: 900 mm - Swing diameter over cross slide: 530 mm - Bed width: 600 mm - Travel of cross slide: 590 mm - Travel of top slide: 250 mm - Cross slide length: 1230 mm - Cross slide width: 345 mm - Saddle guideway length: 860 mm - Tool shank cross-section (height/width): 40 x 40 mm Spindle: - Spindle nose according to DIN 55027 / 55026 size: 11 - Spindle diameter in front bearing: 178 mm - Spindle bore: 128 mm - Main spindle internal taper, metric: 140 mm Main Drive: - Spindle nose according to DIN 55027 size: 11 - Total speed range: 1 - 1120 rpm - Speed range gear stage I: 1 - 350 rpm - Speed range gear stage II: 4 - 1120 rpm - Drive power at 60%/100% duty cycle: 45 / 37 kW - Max. torque at spindle: 6000 Nm Lajdpfxexn Rr Rj Ab Ueh Feed Drive: - Feed range Z/X: 0 - 20 mm/rev - Feed force Z/X: 20 kN - Rapid traverse speed Z/X: 7 / 3.5 m/min Tailstock: - Quill diameter: 140 mm - Quill stroke: 300 mm - Quill internal taper: MK 6 Thread Cutting Range: - Metric threads: 0.1 - 400 mm - Inch threads: 1/4 - 56 TPI - Module threads: 0.125 - 28 mm - DP threads: 1 - 224 DP Connection Data: - Operating voltage: 400 V - Control voltage: 24 / 230 V - Connected load: 55 kW - Rated current: 85 A Machine Dimensions: - Total length: 6900 mm - Total width: 2600 mm - Total height: 2120 mm - Machine weight: 10,500 kg

Condition: ready for operation (used), Year of construction: 1966, Immediately available from location: L & Z Lathe Weiler Year of manufacture approx. 1966 Centre height 140 mm Swing diameter 280 mm Over carriage 180 mm Lsdpfx Aboxqbd No Ujah Turning length 800 mm Spindle bore 24 mm Spindle speeds up to 1600 rpm Drive power 2 kW Chuck diameter 140 mm Multifix tool holder with inserts Weight 1 ton Priced at EUR 1,500.— plus VAT ex location

Condition: used, Year of construction: 1999, Technical details: turning diameter over bed: 570 mm turning diameter over support: 340 mm turning length: 1.000 mm swing diameter over bed: 570 mm centre height: 280 mm centre distance: 1000 mm switched on hours: 26668 h spindle bore: Ø 66 mm revolution per minute: 1 - 2.500 U/min max. torque on the spindle: 1.200 Nm longitudinal feeds:: 0-20 mm/U cross feed: 0-20 mm/U diameter of quill: MK5 Taper tailstock quill adjustment:: 200 mm total power requirement: 30 kW weight of the machine ca.: 3,2 t dimension machine xH: 2,85x2,29x1,9 m Laedpfx Abswtc T To Ush Cycle controlle lathe equipment: -revolving tip (quill) -chip conveyor -cooling water unit manufactor Mayfran *

Condition: like new (used), Weiler Optimum Excellent condition Incl. tooling Lsdpfx Aboxqacke Ueah

Condition: like new (used), Year of construction: 1992, Lathe WEILER Precision center lathe in ergonomic design The Weiler Ergodor is the first German ergonomically designed lathe. It creates a more humane workplace and prevents health problems. The key feature is that the employee can operate this lathe while standing or sitting. Technical data Center width 470 mm Turning length 430 mm Center height 145 mm Rotation Ø over cross slide 160 mm Rotation Ø over bed 300 mm Spindle head, short taper flange Bayonet mounting DIN 55022 size 5 or Camlock clamping D 1-ASA-4 Spindle bore 36 mm DIN 55022 size 5 Spindle inner taper Spindle speeds Speeds 30 - 3550 rpm S Speeds 15 - 3550 rpm Brake motor 3 kW Brake motor 1.5/3 kW Face slide travel 150 mm Travel of the top slide 100 mm Feed rates and thread pitches on the gearbox switchable steps 30 Section 2 1.5/3 kW 38 Lajdpjvgqu Hjfx Ab Ujh Gear ratio in headstock 3 20 Long feeds 150 mm via change gears 100 mm via toothed belt Face feeds = 1/2 Longitudinal feed values Metric pitches 0.2 - 12 mm Module pitches 0.1 - 4 Dimensions 1450 x 640 x 1500 mm Dimensions 1450 x 640 x 1500 mm Net weight 1000 kg Acceptance according to toolmaker's accuracy DIN 8605 20 Built according to the rules of occupational safety, official test no. A. EM 11 1545/80. Encombrement 1450 x 640 x 1500 mm

Condition: good (used), Year of construction: 2008, Weiler DZ 40, year of manufacture 2008, Siemens 840 D control, travel X/Z 200/350 mm, Y axis +/- 25 mm, tailstock MK 4, main spindle max. bar capacity 42 mm, spindle bore 52 mm, rapid traverse X/Z/Q 30/30/20 m/min, 16-position turret – all stations driven, shank diameter 25 mm, driven tools up to 4,500 rpm, parts tray, accessories, driven toolholders, rigid holders. Lajdpjxnna Sofx Ab Uoh

Condition: good (used), Year of construction: 1991, Machine type Lathe - cycle-controlled Manufacturer WEILER Type E30 year of construction 1991 Control Weiler Country of origin Germany Additional information Cycle-controlled lathe WEILER - E30 Technical details Turning diameter max. 330 mm Turning length 750 mm Weiler control Center height 165 mm Ledpfjr Dvqzex Ab Usah Swing diameter over bed 330 mm Max. turning diameter over facing slide 160 mm Face slide travel 180 mm Longitudinal bed slide travel 395 mm Main spindle: Speed range - main spindle 1 - 4,500 min/-1 Drive power - main spindle 9 / 11 kW Max. Torque 165 Nm Spindle head DIN 55027 / 5 Spindle diameter in front bearing 70 mm Spindle bore 40 mm Usable bar diameter ( - ) mm Tool holder: Type MultiFix Turning tool shank cross-section 20 x 20 mm Tailstock: Quill stroke 110 mm Quill diameter 50 mm Tailstock holder MK 3 Feed rates: Rapid traverse max. 10 m/min Feed force 6 / 3 kN Feed range 0 - 20 mm/-1 Thread cutting: metric 0.1 - 400 mm Inch 1/4 - 56 G/1" Module 0.125 - 28 mm.II DP 1 - 224 G/".II Number of threads max. 50 Total power requirement 10 kVA Machine weight approx. 1.5 t Space requirement approx. 2.8 x 2.0 x 2.0 m

Condition: good (used), Year of construction: 2000, Weiler Primus VC, Year of manufacture 2000, Lsdev Ifxiopfx Ab Usah Digital display, Center distance 500 mm, Max. turning diameter over slide 150 mm, Spindle speed up to 4,000 rpm, Spindle bore 40 mm, Spindle drive 1.5 KW, Multifix tool holder, 24 longitudinal feeds, Metric thread, Inch thread,