Used Romer for sale (122)

Year of construction: 2020, condition: new, PLC microprocessor control • HMI operator panel • Phases changed manually or automatically - temporarily • Two separate circuits for water and chemistry, closed circuit • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible The control box is made of IP54 technology User manual, Declaration of conformity, 12 months warranty. ROMER pressure washers use metal sheet that provides protection against chemicals. The washer walls protect against splashing, thanks to the closed chemistry loop, the process can be carried out with small amounts of chemistry. Due to the small amount of refrigerant required, it is easy to heat and cheaper to buy, it also allows you to wash large dimensions impossible to wash in bath tubs. Filtration system Thanks to the filtration system, the chemistry works in a closed circuit, 3 filters of different thickness are used, which prevent garbage and grease from entering the circulation. The chemistry is stored in heated stainless steel tanks from where it is fed by a pump under pressure to the lance Washing of dimensions The pressure washer allows washing of large elements, optionally has a rotating platform that allows rotation of the cleaned element, elements can be applied to it with a forklift or crane. Pjdsfz Dvcjpfx Agworc High pressure pumps The car wash has two preparation phases, both treatments have separate sets of pipes, pumps, wires and guns to minimize mixing of these agents during phase change. Drains have separate valves that manage the return of funds. The carwash is equipped with a logic controller that controls all components. The chemistry is pumped up to 20 bar using a very durable, acid-resistant AISI304 pump with several stages, 3 kW. The rinsing phase uses a high pressure piston pump with ceramic pistons with a capacity of 3kW and provides 160 - 200 bar.

Year of construction: 2020, condition: new, An automatic car wash is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic car wash is equipped with a set of pumps for spraying, it has been designed so that as little liquid as possible migrates to subsequent processes after the process, saving money and improving the quality of washing. Predpfofz I Hxex Agwec This is very important, because the apparent savings in systems made without the use of these solutions may generate much higher costs in the future related to chemicals and waste disposal, which will be simply more. Attention should also be paid to problems with maintaining the required bath parameters. Research and development works allowed us to develop a car wash with the function of drying details (Option) with hot air blown by a set of fans after the washing process. The car wash is equipped with an advanced system of creating own macro programs, which can consist of 10 steps each, depending on the number of tanks, the processes can be repeated, their order can be changed, etc. Each of the tanks has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be carried out e.g. between processes or at the end of the cycle. • Controls installed on a swivel arm for better access • PLC microprocessor control • 7 "touch control panel • A very large number of nozzles compared to other solutions • (Option) Possibility of drying details after washing • Ability to create your own advanced programs • Advanced system of dampers made of acid-proof steel sheets, double secured with limit switches • Control system for tight closing and full opening of the flaps • To minimize fluid mixing, separate lines, nozzles, tanks for each treatment • Intelligent control - in the event of a power cut / sudden shutdown, the fluids cannot be mixed • Fully automatic operation

Year of construction: 2020, condition: new, Washers Ultrasonic Baths for washing, phosphatizing, chromating, degreasing, removing paint coatings materials In ROMER Ultrasonic Washers, stainless steel is used which provides protection against acids. Bathtubs have an additional insulation wall, so they do not lose temperature and heat up faster. Good quality materials ensure long life of the vibrating elements. Heating system The heaters used in the ROMER bathtubs are made of the highest quality materials and are made of high temperature resistant ceramic elements. The heating system used ensures great thermal efficiency, hot water automatically mixes with cold water, heating the entire bathtub. Ultrasonic transducers Ultrasonic elements used in ROMER washers are installed in immersion modules, which better reflect vibrations and are exchangeable. The ultrasound range is 20-40kHz depending on the washed element, lower frequencies are used for large elements of high strength, lower for jewelry, sensitive mechanical systems, etc. All transducers are connected by high temperature resistant cables. Pedpfx Agsfz I N Tjwsrc

Year of construction: 2020, condition: new, An automatic car wash is a solution that allows you to reduce costs, improve quality and increase the efficiency of the surface preparation process. The automatic car wash is equipped with a set of pumps for spraying, it has been designed so that as little liquid as possible migrates to subsequent processes after the process, saving money and improving the quality of washing. This is very important, because the apparent savings in systems made without the use of these solutions may generate much higher costs in the future related to chemicals and waste disposal, which will be simply more. Attention should also be paid to problems with maintaining the required bath parameters. Research and development works allowed us to develop a car wash with the function of drying details (Option) with hot air blown by a set of fans after the washing process. The car wash is equipped with an advanced system of creating own macro programs, which can consist of 10 steps each, depending on the number of tanks, the processes can be repeated, their order can be changed, etc. Each of the tanks has its own unique icon and name, enabling the operator to work intuitively. Optionally, the tanks can be equipped with bath replenishment systems, which can be carried out e.g. between processes or at the end of the cycle. • Controls installed on a swivel arm for better access • PLC microprocessor control • 7 "touch control panel • A very large number of nozzles compared to other solutions • (Option) Possibility of drying details after washing • Ability to create your own advanced programs • Advanced system of dampers made of acid-proof steel sheets, double secured with limit switches • Control system for tight closing and full opening of the flaps • To minimize fluid mixing, separate lines, nozzles, tanks for each treatment Podsfz Nbljpfx Agwsrc • Intelligent control - in the event of a power cut / sudden shutdown, the fluids cannot be mixed • Fully automatic operation

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air Psdpofz U Nuofx Agwerc • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes Psdpfjfz U Rcjx Agwjrc • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Pedpfx Ajfz U Tqegwerc Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Year of construction: 2020, condition: new, PLC microprocessor control • HMI operator panel • Phases changed manually or automatically - temporarily Prodpfx Agef Aaaljwoc • Two separate circuits for water and chemistry, closed circuit • Intelligent control - in the event of a power cut / sudden shutdown, no mixing of liquids possible The control box is made of IP54 technology User manual, Declaration of conformity, 12 months warranty. ROMER pressure washers use metal sheet that provides protection against chemicals. The washer walls protect against splashing, thanks to the closed chemistry loop, the process can be carried out with small amounts of chemistry. Due to the small amount of refrigerant required, it is easy to heat and cheaper to buy, it also allows you to wash large dimensions impossible to wash in bath tubs. Filtration system Thanks to the filtration system, the chemistry works in a closed circuit, 3 filters of different thickness are used, which prevent garbage and grease from entering the circulation. The chemistry is stored in heated stainless steel tanks from where it is fed by a pump under pressure to the lance Washing of dimensions The pressure washer allows washing of large elements, optionally has a rotating platform that allows rotation of the cleaned element, elements can be applied to it with a forklift or crane. High pressure pumps The car wash has two preparation phases, both treatments have separate sets of pipes, pumps, wires and guns to minimize mixing of these agents during phase change. Drains have separate valves that manage the return of funds. The carwash is equipped with a logic controller that controls all components. The chemistry is pumped up to 20 bar using a very durable, acid-resistant AISI304 pump with several stages, 3 kW. The rinsing phase uses a high pressure piston pump with ceramic pistons with a capacity of 3kW and provides 160 - 200 bar.

Year of construction: 2020, condition: new, Use of one photocell Using one photocell in the space of workpiece allows you to measure the length of the workpiece and, consequently, gives you the opportunity to turn on the guns when the item is in range, and to switch off the gun immediately after the workpiece is finished. The photocell is included in the standard equipment.Identification of details using special tags. Prjdpjfy T Arjfx Agwsc A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus braking the energy and powder coating. Vertical detection of the detail of the workpiece. The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. Application of light gates with multiple sensors horizontally and vertically. This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to manipulate the manipulators. Benefits of using gates and photocells The benefits of using photocells or light gates are primarily energy and powder savings. Eliminate painting of a zone in which there is no detail. With the use of light gates, precise control of the guns. Our lines can be optionally equipped with photocells, or light gates Using one photocell in the workpiece space allows you to measure the length of the workpiece and, consequently, gives you the ability to turn on guns when the item appears in their range, and turn off the gun immediately after the workpiece is finished.Identification of details using special tags. A plate with identification holes is placed over the suspension. Based on this, the PLC controller in conjunction with the photocell recognizes the painted detail, turns on and off the guns in a timely manner - thus saving the energy and powder.The use of light gates with detectors horizontally allows the PLC to analyze the vertical shape of the workpiece. The PLC counts the time in which the detail will appear in the gun space - allowing guns to be selectively switched on or off.Using of light gates with multiple sensors horizontally and vertically This solution allows precise measurement of the dimensions of the workpiece, which makes it possible also to adjusting the manipulators.The benefits of using photocells or light gates are primarily powder and energy savings Eliminate painting of a zone in which there is no detail With the use of light gates, precise control of the guns The PLC counts the time at which the detail should appear in the gun space - allowing guns to be selectively switched on or off.

Year of construction: 2020, condition: new, ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual.The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out. The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction.The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore. ROMER cabins are equipped with 4 "color touch screen.The cab operation is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual. Filter clogging sensor The cabins are fitted with a sensor that queues filters for cleaning when they plug. The system also informs when the filters have already worn out Automatic filter cleaning The electronic system of automatic filter cleaning has a range of adjustment of cleaning frequency and time of firing. Each filter is cleaned separately, and the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore.Low volume Aluminum fans are very quiet, work at 74-79dB - It's not much. it is difficult to talk even with a standard cabin construction. Broach through the cabin The cabin, by pulling the sling beams inside the cab, improves the work efficiency, thus relieving the painter, who does not have to move them by hand anymore.Automatic filter cleansing ROMER's cabins are equipped with an electronic automatic filter cleaning system. Booth has an adjusted range of cleaning interval, time of the impulse. Each filter can be cleaned individually by using control buttons. We know from experience that it's hard to expect from an operator to clean every single filter entirely. Thanks to this system operator won't have to worry about it anymore. Booth drive-through chain Thanks to installed drive-through chain there is no need for an operator to drag every element into the booth himself.Elements drive through the booth all on their own which improves the efficiency and allows operator to focus just on the painting part.Regulated air suction In our booths we install an anti-static plate that covers filters. It protects filters from a first wave of a powder. In a well designed booth it also improves the velocity of air moving across the painted element that reaches filters. It improves suction and makes painting easier. Location of a plate can be regulated Prsdpjfy T Tbefx Agwjc ROMER's powder booths are fitted with professionally made tanks, which are responsible for the collection of air needed to clean the filter. Compressed air is released from the tank in a fraction of a second while passing through the ROMER JET ™ system expands in the filter at high velocity and escapes through the micro holes in the filter cleaning it, and the

Year of construction: 2020, condition: new, ROMER® is the largest producer of powder paint shops in Poland, and one of the largest in Europe. ROMER® is over 10,000 manufactured devices operating in over 45 countries around the world. ROMER® Produces single technological equipment for powder paint shops as well as complete fully automatic turnkey paint shops. Podpfx Aefzq Ryjgwerc ROMER® provides heating solutions for the aero and automotive industries for the largest concerns in the world. We provide warranty and post-warranty service of the devices we sell with a full range of spare parts.

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Pedpfx Ajfz Apqegwsrc Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, condition: new, Washers Ultrasonic Baths for washing, phosphatizing, chromating, degreasing, removing paint coatings Psdpfx Agjfz Aw Hsworc materials In ROMER Ultrasonic Washers, stainless steel is used which provides protection against acids. Bathtubs have an additional insulation wall, so they do not lose temperature and heat up faster. Good quality materials ensure long life of the vibrating elements. Heating system The heaters used in the ROMER bathtubs are made of the highest quality materials and are made of high temperature resistant ceramic elements. The heating system used ensures great thermal efficiency, hot water automatically mixes with cold water, heating the entire bathtub. Ultrasonic transducers Ultrasonic elements used in ROMER washers are installed in immersion modules, which better reflect vibrations and are exchangeable. The ultrasound range is 20-40kHz depending on the washed element, lower frequencies are used for large elements of high strength, lower for jewelry, sensitive mechanical systems, etc. All transducers are connected by high temperature resistant cables.

Year of construction: 2020, condition: new, Touch control ROMER cabins are equipped with 4 "color touch displays. Operation of the cabin is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual Filter clogging sensor A sensor is installed in the cabins, which queues the filters for cleaning when they become clogged. The system also informs you when the filters have worn out Automatic filter cleaning The electronic system for automatic filter cleaning has a range of cleaning frequency and shot time adjustment. Each of the filters is cleaned separately, the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Low volume Aluminum fans are very quiet, they work at the level of 74-79dB - It's not much. Podpfxofz A Ilo Agwjrc with the standard cabin structure, it's even hard to talk. Broaching machine through the cabin By dragging the suspension beams within the cabin, the cabin improves work efficiency, thus relieving the painter who no longer has to move them by hand. Explosion-proof design The booths are designed to prevent the formation of an explosive mixture during the painting process. Each of the components has been carefully selected to minimize this risk.

Year of construction: 2020, condition: new, The ROMER company is also involved in the production of suspended transport systems. Cross traverses (Cross transports) are designed and manufactured for specific installations Oghxp Examples of equipment are presented below: Transport systems Depending on the customer's requirements, the transport systems can move on the floor or be hung on poles. Prjdpfefz Difex Agwec - For comfortable solutions for manual installations, we recommend suspended crossbeams (cross transport). - For automated systems, chain conveyors are most often used that do not stop and are a great solution for companies that focus on quality and repeatability of the process. - For companies that make different items at the same time and have, for example, several cabins with different colors, flexible solutions are used with the use of a power-and-free conveyor. This is the most expensive solution.

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg Psdpefz Dknefx Agwjrc • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, ROMER manipulators are characterized by quiet operation. They can be widely used both with simple, as well as complex multidimensional processes Predpfx Ajfz Dmmegwec They are programmed using a PLC controller Working with long and short strokes The toothed belt transmission ensures quiet operation Maintenance-free AC motor Narrow column design for space saving. The robust construction of the manipulators ensures great possibilities and high stability. The manipulator is equipped with a 7 "touch panel or is externally controlled via the ModBus protocol with RJ45 cables

Year of construction: 2020, condition: new, DESCRIPTION Podpfx Aofz Dwzjgwjrc The demineralized water station is used to produce the so-called demi water using ion exchange technology. The station consists of 3 columns Strongly acid cation exchanger working in the sodium cycle, Strongly basic anion exchanger working in the chloride cycle, Carbon filter Our RDI-2 / RDI-4 demineralization stations are equipped with fully automatic control heads. Rouezts The columns are made of AISI316L steel

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits Predpfxofz I Rmj Agwec • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Pedpfxjfz I R Rs Agwerc Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, High hauling power Soundproofed construction Electronic control 4 "touch panel Constant measurement of flow and filter clogging Final filters Inverter controlled fan • Electrical data 22kW 380-400V 50-60Hz • Theoretical capacity 12000 m3 / h • 1/4 "pneumatic connection • Number of filters 8 pcs. • 160 m2 filtration area • Automatic filter cleaning • Air consumption max. 12L 6-8 bar / shot • 50L waste container capacity Description • Dust collector equipped with an efficient radial impeller • Two working modes - Full power and ECO • The basis weight of the material used in the filter is as much as 260g / m2 • High suction power with low energy consumption • Waste container for easy removal of paint deposits • Inspection door for filter replacement • Each filter has its own solenoid valve Power Predsfz I Sgjpfx Agwjc Inverter Constant air flow measurement Vacuum sensor Capacity (m3h) Filter area (m2) Paint container

Year of construction: 2020, condition: new, 7" Touchpad Large color touch panel looks aesthetically and uses comfortably and intuitively. Set on it all the important parameters.Memory 20 programs each with 10 events You can save up to 20 programs and activate up to 10 consecutive events time-temperature arranged in the heating curve. This is especially needed for the more demanding process.Information about consumption of power Consumption is calculated based on the settings of the burner. This feature will allow you to estimate the cost of the cycle, consumption and plan check staff.Recorder of cycle USB Each of the ovens is equipped with two-channel temperature recording on USB flash drive.. Each file is automatically created and is responsible for a separate cycle are recorded temperature extremes, hour and minute measurement. Files are saved in * .csv (Excel sheet) For all buyers the end of 2016 option is free, the competition for the option you have to pay up to several thousand euros. History 20 latest of burn Something's wrong? and perhaps too few overbroad elements from the oven? Now you check thoroughly oldest and lastest burning parameters, how often took, whether cycle proceeds without any problems, what was the consumption and when they ran. Predpfx Aefz U Nbegwoc Start the oven automatically at 6 am How many times have you stay after hours and expecting end of the cycle? If you own a powder coating plan that works for a long time, You know exactly what we are talking about. With our solution you can leave cycle not cured in the oven, to automatically end when you come to the job next morning.

Year of construction: 2020, condition: new, Pneumatic connection 1 " • Controls 7 "color touch panel • Paint tank capacity 6-7 kg • Air consumption during painting 15Nm3 / h • Air consumption for cleaning 350Nm3 / h • Hopper paint level sensor Yes • Ultrasonic screener Yes Predjfz U Rrjpfx Agwoc • Powder injectors up to 12 pcs Description • RP-01 pump for topping up the paint with fresh paint from cardboard • Two modes of operation, paint recovery with mixing or total waste • Sealed fluidization paint hopper • Automatic program for cleaning the tank and injectors with compressed air • Hopper powder level sensor assembly • Automatic refilling of the tray with paint from cardboard • Paint level sensor in refill box • An audible alarm alerts the operator when there is low paint in the box • The center is connected with the cabin control via ModBus protocol • Programmable powder suction valve to keep the powder center clean

Year of construction: 2020, condition: new, Gravity heating system Thanks to the use of a gravity heating system in SPARK series gravity furnaces, we can boast of a good result of temperature homogeneity, our tests have shown that the air temperature uniformity in our gravity furnaces, with the appropriate arrangement of elements, does not exceed ± 5 ° C! We owe the result to our heating element assembly technology. Rapid heating SPARK series gravity furnaces have specially designed heaters that quickly give off heat, thanks to which our furnaces heat up quickly. We owe rapid heating to the applied seals and insulations, the specially profiled gasket does not contain asbestos and is safe for the user. Optimization of the insulation, no contact between the furnace chamber and the casing minimizes heat loss and saves power. Depending on the model, our furnaces heat up to 8 ° C per minute. Psdpfx Asfy T R Dogwerc Transport system The SPARK series ovens are equipped with two bottom transport carriages as standard. In response to the market demand for inexpensive solutions, we have developed a manual bottom transport system that allows you to transport large dimensions with a minimum of force. Our system allows for optimal use of the entire surface of the furnace and ensures high cleanliness of the painted elements. Thanks to the use of two trolleys, the trolley moving around the hall does not contaminate the interior of the furnace. The top trolley is used to enter the furnace itself. The use of one trolley causes the introduction of contaminants from the floor into the furnace chamber, our system eliminates this problem.

Year of construction: 2020, condition: new, Touch control ROMER cabins are equipped with 4 "color touch displays. Operation of the cabin is intuitive, takes place in 3 modes, automatic (time), automatic (based on a clogged filter sensor), or manual Filter clogging sensor A sensor is installed in the cabins, which queues the filters for cleaning when they become clogged. The system also informs you when the filters have worn out Automatic filter cleaning The electronic system for automatic filter cleaning has a range of cleaning frequency and shot time adjustment. Each of the filters is cleaned separately, the filters can also be cleaned manually using the buttons. We know from experience that it is difficult for the operator to enforce filter cleaning. Thanks to this system, the operator will not have to think about it anymore. Low volume Predefzktzepfx Agwsc Aluminum fans are very quiet, they work at the level of 74-79dB - It's not much. with the standard cabin structure, it's even hard to talk. Broaching machine through the cabin By dragging the suspension beams within the cabin, the cabin improves work efficiency, thus relieving the painter who no longer has to move them by hand. Explosion-proof design The booths are designed to prevent the formation of an explosive mixture during the painting process. Each of the components has been carefully selected to minimize this risk.