Used Rolling Hollow for sale (6,504)

Condition: used, Thread rolling machine, cold rolling machine, thread rolling machine, profile rolling machine Manufacturer PEE-WEE Type P 24 Q serial no. LC2403099 year of construction 2004 Rolling force max. 24 ton. Tool diameter max. 200 mm Rolling spindle diameter 69,85 mm Tool bore diameter 70 mm (nominal diameter) Tool length, tool length max. 180 mm Workpiece diameter max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 rpm Motor power hydraulics approx. 3 kW Motor power roller drive 5.5 kW Mains connection 400 Volt, 50 Hz - Swivel roller spindle for threaded continuous rollers Bedpfx Abeh A S Hto Tedk - Rolling spindle speed in 4 stages via gear changeover - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons good condition Grooving rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating into the workpiece up to the nominal diameter. The thread length is maximum as long as the rolling tools are wide. Continuous rolling: When the thread length is greater than the rolling tool width. Through-feed tools have 3 sections - the infeed, the calibration section and the outfeed. Grooved rollers have no pitch and are swiveled with the pitch angle of the profile to be rolled. Pitch rollers differ from grooved rollers in that they have a pitch in the profile. The sum of the pitch angle and the swivel angle gives the pitch angle in the workpiece.

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: NC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: SIEMENS, controller model: PLC, number of rollers: 4, roller (bottom) diameter: 150 mm, roller (top) diameter: 150 mm, side roll diameter: 140 mm, roller diameter: 150 mm, roller length: 2,050 mm, working width: 2,000 mm, roller height adjustment: 18 mm, working height: 800 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 4 mm, sheet thickness aluminum (max.): 6 mm, sheet thickness brass (max.): 6 mm, sheet thickness copper (max.): 6 mm, overall weight: 2,800 kg, total length: 3,800 mm, total width: 1,200 mm, total height: 1,100 mm, power: 3 kW (4.08 HP), input voltage: 400 V, input frequency: 50 Hz, number of digital displays: 4, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BENDING MACHINE NC HYDRAULIC MODEL 2000X6 MM / 4 MM PREBEND PROGRAMMABLE AUTOMATIC ROLLING NC 4 AXIS CONTROLLER Capacity: plate width 2000 mm thickness rolling 6 mm pre-bending 4 mm minimum diameter of rolling D= 180 mm depending on the plate thickness and strength Rollers length 2050 mm Upper roll size 150 mm Lower roll size 150 mm Rollers hardened surface high strength smooth surface finishing suitable for rolling stainless steel quality plates Conical plate rolling attachment Rotation electric powered on central rollers for bending traction of the plate Pre-pinch load variable upon plate thickness and strength Console electric commands push buttons with digital readout of the 4 rollers on the screen. NC programmable 4-axis to set automatic rolling with save 200 programs in memory front side hydraulic opening to remove the rolled shells Bdjdpjw Hpzwjfx Ab Tsk speed slow/fast variable safety installation with emergency stop. Instruction manuals for operation and service. Layout mm 3800x1200xH1100 mm Weight 2800 Kgs

Condition: like new (used), Thread rolled both ends the same time! Bdjdowalx Eopfx Ab Tsk Diameter range M6-M16 Max total length 600 mm. Max threaded length 60 mm. Adjustment is not difficult at all. We could offer machine with dies according to your wish, be made by our factory too. We are located at Athens, Greece, near to the center. You can view machine under power after appointment.

Condition: ready for operation (used), Year of construction: 1994, A Schüco profile rolling machine for the thermal separation of aluminum profiles in window, door and façade construction is available. Processing speed: 45m/min, control speed: 15m/min, max. profile height: 400mm, max. profile width: 250mm, max. insulating bar width: 300mm, machine dimensions X/Y/Z: approx. 2700mm/800mm/1650mm, weight: approx. 900kg. Including automatic insulating bar feeder, safety cage/alignment roller set, roller conveyor and roller conveyor extension. Documentation available. On-site inspection is possible. Bdjdpfx Abewtg Hwe Tok

Condition: used, Year of construction: 2002, functionality: fully functional, machine/vehicle number: M24I/9053, Offer Number: M24I/9053 Machinetype: thread rolling machine - 2 rolls Make: BAD DÜBEN Type: PRX 32 E CNC Constr. year: 2002 diameter range: 10-24 mm Forging power: 7-20 to thread length plunge method: 195 mm daylight: 160 mm max. pitch: 3,5 mm roller bore: 80 mm roller width: 235 mm Bdsdpjw Nxnwefx Ab Tjk roller length: 195 mm rpm: 40 - 315 Location: Germany

Condition: new, Year of construction: 2024, functionality: fully functional, type of input current: three-phase, total width: 1,800 mm, total length: 2,000 mm, total height: 1,500 mm, overall weight: 5,000 kg, warranty duration: 12 months, spindle diameter: 80 mm, roll diameter: 240 mm, roll width: 220 mm, thread length: 6,000 mm, workpiece diameter (max.): 120 mm, new machine for immediate delivery Bedpfx Ajuafrujb Todk

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base Bjdpfx Absuz If Ns Tedk - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: new, functionality: fully functional, Year of construction: 2025, operating hours: 0 h, machine/vehicle number: plate roll, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: MG EVO, controller model: EVO 4 AXIS, number of rollers: 4, roller (bottom) diameter: 140 mm, roller (top) diameter: 160 mm, side roll diameter: 150 mm, roller diameter: 200 mm, roller length: 2,050 mm, working width: 2,000 mm, working height: 700 mm, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 6 mm, sheet thickness stainless steel (max.): 6 mm, sheet thickness aluminum (max.): 6 mm, overall weight: 2,200 kg, total length: 3,200 mm, total width: 1,100 mm, total height: 1,200 mm, power: 4 kW (5.44 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 4 ROLL BRAND MG ITALY, HYDRAULIC MODEL M2006P EVO_CNC PLATE BENDING ROLL PLANETARY DESIGN DOUBLE PINCH PRE-BENDING CNC_EVO PROGRAMMABLE AUTOCALCULATION AUTOMATIC PLATE ROLLING Capacity: -Width of plate: 2000 mm -Thickness of plate rolling 6 mm -Thickness of plate pre-bending 4 mm Rolls -useful width mm. 2050 -Top roll mm. 160 - Lower roll mm. 140 Configuration installed: • Surface hardening of the four rolls, smooth finishing suitable for stainless plates rolling • Dual pre-pinch, with adjustable force upon the input of plate thickness Bdjdpfxow Dnd Se Ab Tek • Conical bending hydraulic attachment - hardened contrast pad. • Power driven rolls rotation top/bottom gearbox axial direct drive hydraulic each roll. • Calibration system for re-rolling of welded shells rounding. • Console electric independent with centralized commands joysticks and CNC screen readout. • CNC controller on touch screen 15” , CAD/CAM interface 4 axis auto calculation software package. with digital readout of the axis for use in manual rolling, semiautomatic and fully automatic programmable. • Opening front side hydraulic drop-end to unload closed shells. • Variable working speed step-less axis interpolation. • Safety installation with emergency stop. • Instruction manuals for operation and service.

Condition: new, Year of construction: 2024, Ring Rolling machine Zopf profile bending machine model ZB 100/3 H - three driven shafts - hydraulic adjustment of center roller - digital readout with memory - working position horizontal and vertical - shafts are supported by conical bearings - slide bars - shaft diameter 60 mm - roller diameter 215 mm - main motor 1,5 kw - hydraulic mtor 1 kw - hydraulic pressure 18 ton Bdsdpfod Eyz Uox Ab Tsk - bending capacity flat material up to 80x15 mm on edge - round tube up to 100x2,0 mm - angle iron leg in and out side 70x70x8 mm - weight 800 kg

Year of construction: 1974, condition: ready for operation (used), A Schwabenthan laboratory rolling mill is available. Roll width: 110mm, roll length: 350mm, roll diameter: 110mm, roll speed: 27rpm, bottom-roll axle distance: approx. 1200mm. On-site inspection is possible. Bodpfx Aswmqw Tjb Todk

Condition: used, Year of construction: 2001, functionality: fully functional, machine/vehicle number: M50E/9046, Offer Number: M50E/9046 Machinetype: hot rolling machine Make: SKF Type: EMB 110 Constr. year: 2001/2021 diameter range: 110 mm max. outside dia. of round pieces: 110 mm kind of heating: 335 KW Location: Europe Bsdsw Nxiuspfx Ab Todk

Condition: good (used), Maximum pressure 25tn • 69 and 85mm axles • Machine in very good condition, completely revised Bodpfxogqumpj Ab Tsdk

Condition: used, Writing desk, mobile desk, shelf trolley, logistics trolley, shelf trolley Transport trolleys, platform trolleys, workshop trolleys Bdsdpfopflp Eox Ab Tsk FETRA type 5834 Writing surface height: 1100 / 1190 mm Writing surface: 605 x 585 mm Shelves: 600 x 495 Load capacity per shelf: 50 kg Total load capacity: 100 kg - Rolling desk made of tubular steel and sectional steel - Screw construction, powder-coated, blue RAL 5007 - Writing surface on wooden board with stop bar, inclined approx. 10 - 2 shelves, can be screwed in variably (2 file heights possible) - 4 swivel castors (Ø 125 mm) with plastic rim and rubber coating on the running surface - 2 fixed castors with brakes Space requirement L x W x H: 600 x 600 x 1190 mm Weight: 25 kg Very good, as new condition 8 pieces available, price per piece

Condition: used, Year of construction: 1987, rolling capacity max. NA t workpiece diameter 38 mm workpiece length 500 mm total power requirement 24 kW weight of the machine ca. 10 t dimensions of the machine ca. m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Bsdot Hw D Dspfx Ab Tedk Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Accessories / Special Features * KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. * Originally, external gears were formed on the machine using pinion cages (no. of teeth = 25), Ø approx. 32 mm x 14 mm long, workpiece Ø approx. 80 x 80 mm long. * Various accessories: * Separate switch cabinet. * Separate hydraulic unit, 900 l. * Coolant device in the machine. * Control panel with malfunction message in plaintext, etc. Roto Flo machines are ideal for mass production of smaller gears/profiles. The coldforming process is a lot faster and more economical than other chip removing methods. Workpieces are clamped between 2 live centres and 2 synchronous opposed directional coldforming racks simultaneously engage the workpart and start rotation. During rotation, the profile is formed successively within one stroke. In the calibrating zone, the profiling and surfacing performance of the tool are optimised. Profiles do not require a run-out. The coldforming process requires a rigid and heavy duty construction of the machine, which ensures the required precision over the years. Between 25,000 and 100,000 working cycles can be performed with one set of racks, also for serrations. Condition : Very good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We always have a good selection of gear machines available. Please let us know what you need.

Year of construction: 2025, condition: ready for operation (used), A baguette long rolling machine in mint condition for the long-molded forming of dough pieces for the production of baguettes is available. Table dimensions X/Y: approx. 1600mm/850mm, long rolling plate dimensions X/Y: approx. 1200mm/610mm, conveyor belt dimensions X/Y (extended): approx. 3100mm/610mm, max. gap opening: 75mm, weight: approx. 100kg. Documentation available. On-site inspection is possible. Bsdowihz Iopfx Ab Todk

Condition: used, Year of construction: 1983, functionality: fully functional, machine/vehicle number: M14L/6106, Offer Number: M14L/6106 Machinetype: thread rolling machine - planetary die Make: SIMA Type: RAP11 Constr. year: 1983 diameter range: 6-12 mm shaft length under head: 8-75 mm max. thread length: 75 mm output pieces/min: 1000 Location: In our warehouse Bdodpjwi Tbyofx Ab Tsk

Year of construction: 2004, condition: ready for operation (used), A high-temperature rolling machine for glass fiber reinforced compounds is available. 1) Large roller Comerio Ercole, year of construction: 1970, working width: 1500mm, roller diameter: 600mm, roller gap: electrically adjustable, lubrication: circulating oil lubrication. 2) Small roller Meccaniche Moderne, year of construction: 1966, working width: 800mm, roller diameter: 400mm, lubrication: circulating oil lubrication. 3) Horizontal mixer, volume: 2.5m³. 4) Big bag frame with crane. 5) 2x gravimetric dosing scales with control. 6) Conveyor belts and spiral balancing conveyor. 7) Condux HM 45/60 LA hammer mill (lined) with a 1000 mm vibrating screen. 8) 2x Lauda heaters. Including cement mixer, bucket elevator, silo, bagging scales, glass feed rack and a control cabinet for overall plant control. Documentation available. On-site inspection is possible. Bjdpfxjwk Nldj Ab Todk

Condition: used, Year of construction: 1970, functionality: fully functional, machine/vehicle number: M14L/6907, Offer Number: M14L/6907 Machinetype: thread rolling machine - flat die Info: vibratory feeder Make: MALMEDIE Type: AG13 Constr. year: 1970 diameter range: 8-16 mm shaft length under head: 150 mm max. thread length: 83 mm output pieces/min: 120 Bsdpfx Abowi Ta No Todk Location: In our warehouse

Condition: used, Year of construction: 1971, functionality: fully functional, machine/vehicle number: M14L/8133, Offer Number: M14L/8133 Machinetype: thread rolling machine - flat die Info: tube feeder for studs and headless parts Bsdewi S Irepfx Ab Tsdk Make: PELTZER-EHLERS Type: NKW12-ST8 Constr. year: 1971 diameter range: 6-12mm shaft length under head: 95 mm max. thread length: 90 mm output pieces/min: 55 Location: In our warehouse

Condition: used, Year of construction: 1987, functionality: fully functional, machine/vehicle number: M14L/8196, Offer Number: M14L/8196 Machinetype: thread rolling machine - flat die Make: SASPI Type: GV3-20 Bdjdpfx Abjwi S Hzo Tsk Constr. year: 1987 diameter range: 4-12 mm shaft length under head: 150 mm max. thread length: 130 mm output pieces/min: 85-220 Location: In our warehouse

Condition: used, Year of construction: 1987, functionality: fully functional, machine/vehicle number: M14L/8402, Offer Number: M14L/8402 Machinetype: thread rolling machine - flat die Info: vibratory feeder Make: MENN Type: GW83L Constr. year: 1987 Bdodpfswi S A Njx Ab Tjk diameter range: 4-12 mm shaft length under head: 150 mm max. thread length: 105 mm output pieces/min: 80-260 Location: In our warehouse

Condition: used, Year of construction: 1973, functionality: fully functional, machine/vehicle number: M14L/8559, Offer Number: M14L/8559 Machinetype: thread rolling machine - flat die Info: vibratory feeder Make: MENN Type: GW62 Constr. year: 1973/92/23 diameter range: 3-8 mm shaft length under head: 80 mm max. thread length: 55 mm output pieces/min: 300 Location: In our warehouse Bsdpfewi Sxwjx Ab Tjdk

Condition: used, Year of construction: 1984, functionality: fully functional, machine/vehicle number: M14L/8571, Offer Number: M14L/8571 Machinetype: thread rolling machine - flat die Info: vibratory feeder Make: HILGELAND Bsdjwi Sw Hjpfx Ab Tedk Type: R2LSP Constr. year: 1984 diameter range: 3-8 mm shaft length under head: 150 mm max. thread length: 80 mm output pieces/min: 400 Location: In our warehouse

Condition: used, Year of construction: 1974, functionality: fully functional, machine/vehicle number: M14L/8630, Offer Number: M14L/8630 Machinetype: thread rolling machine - flat die Info: vibratory feeder Make: MENN Type: GW52 Constr. year: 1974/24 diameter range: 2,5-6 mm shaft length under head: 80 mm max. thread length: 40 mm output pieces/min: 600 Bdedpfswi Swgex Ab Tok Location: In our warehouse

Condition: used, Year of construction: 1987, functionality: fully functional, machine/vehicle number: M14L/8631, Offer Number: M14L/8631 Machinetype: thread rolling machine - flat die Info: vibratory feeder Make: MENN Bedowi Swajpfx Ab Tjdk Type: GW63 Constr. year: 1987/24 diameter range: 3-8 mm shaft length under head: 80 mm max. thread length: 58 mm output - pieces/min: 250-480 Location: In our warehouse