Used Rolling Rack for sale (10,246)

Condition: good (used), Year of construction: 1992, machine/vehicle number: 921602-3, Offer 25341 Technical specifications: Ncodpfx Ajzdrqgemyew - Maximum load capacity per compartment level: 2000 kg - 6 pull-out compartment shelves - 1 upper storage compartment - Compartment dimensions: approx. W 2600 x D 1350 mm - Maximum extension of the compartment shelves: approx. 100% - Distance between the compartment shelves: 240 mm - Space required: approx. W 2950 x H 2250 x D 2480 mm - Space required in depth when extended: 2980 mm - Weight: approx. 1800 kg

Condition: new, Year of construction: 2026, 1A Gmatick Storage Paternoster (roll rack) The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils. With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage. As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick. • Storage rods ø 42.4 mm • Sleeves inside Ø max. 82 mm,. • Load chain as a hollow pin chain with a breaking load of 100 kN, • Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars. • Control with a key switch (dead man) for on / off • Rotational speed of the chain is approx. 5.5 m / min • Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz • Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow • ground load data at least 2, 2 kg / cm² • Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster. • Requirement for the installation of the Paternoster is a viable, flat and solid floor, • Floating floors you can’t install a Paternoster. It is forbidden Nsdpfjff Huwsx Amyecw

Condition: used, - Year of construction: unknown - min. part length 320mm - Max. part height approx. 210mm - number of levels 7 Stk. - distances between levels 100 mm - insert depth 650 mm - number of vertical posts 300-450-450-300mm, 5 Stk. Nsdpfozf N Hnjx Amyjcw - overall height 1740 mm - Overall width 1.540 mm

Condition: like new (used), Large quantity of racks and trolleys for 1300mm retorts. Have been used for pouches and ready meal trays. Njdpfxjihgdgs Amyecw Up to 180 units available.

Condition: new, functionality: fully functional, Year of construction: 2026, color: grey-black, overall weight: 15,000 kg, maximum load weight: 12,000 kg, empty load weight: 2,400 kg, loading space width: 2,500 mm, loading space length: 6,500 mm, loading space height: 125 mm, Dear Sir or Madam, We are offering a new roll-off platform for sale, manufactured in our own production facility. The platform features the following: - Manufactured according to DIN 30722-1 - Mounting bracket, 50mm diameter - Hook height 1570mm - Usable platform length 6,500mm - Tare weight 2,400kg / Payload 12,600kg - 5mm diamond-plate floor / 4mm front wall thickness - Robust hook mount with surrounding plates - IPN 180 longitudinal beams / reinforced - External rollers, lubricatable and replaceable Nsdszhid Sspfx Amyecw - Primer, painted in RAL 7016 / Anthracite - C-locking mechanism according to DIN - 5 pairs of recessed lashing eyes with a tensile force of 2.5t each - Each side with perforated strips with 30mm holes - 6x robust and lockable inserts for leveling the wheel tracks - Wheel tracks recessed by 120mm - Recessed wheel tracks, each approx. 5500mm long & 708mm wide - 2x lockable steel storage compartments at the front - 2x lashing rings with 5.3t tensile force each on the inside of the front wall / 2x 5.3t lashing rings embedded in the floor at the rear - 2x warning markings according to §32 (1) StVO & DIN - Incl. type plate & container inspection according to DGUV rule 114-010 - Immediately available Also available in 5.5m and 6m usable platform length. Nationwide delivery possible for an extra charge! If you are interested in other roll-off container products, we would be delighted to receive your inquiry!

Condition: good (used), Year of construction: 1992, machine/vehicle number: 921602-1, Offer 25344 Technical data: Ncsdpfx Ajzf E Saomyew - Maximum load capacity per shelf level: 2000 kg - 6 extendable shelves - 1 upper storage compartment - Shelf dimensions per compartment: approx. W 2600 x D 1350 mm - Maximum extension of the shelves: approx. 100% each - Distance between the shelves: 240 mm - Space requirement: approx. W 2950 x H 2250 x D 2480 mm - Space requirement in depth when extended: 2980 mm - Weight: approx. 1800 kg

Condition: new, functionality: fully functional, machine/vehicle number: 60.21.287, This is a tray rack trolley from the premium manufacturer Rational, suitable for combi-steamers of size 20-1/1. The tray rack trolley offers space for 15 x 1/1GN containers. With a rail spacing of 84 mm, you may achieve better utilization when loading compared to the tray rack trolley with 20 slots. Ncsdpfx Aoyfuhromyow Rational article number: 60.21.287 The recommended retail price (RRP), gross, is: €2528, our special price: €1399 gross. You will receive an invoice with VAT shown. Service: We will gladly assist you in arranging a certified Rational customer service technician. Are you looking for a specific Rational equipment type? Ask us, we have access to a large selection of used and new equipment. We will be happy to advise you on all equipment types. Our used equipment service for you: * 6 months warranty on electrical parts, limited to the replacement of defective parts, without installation and removal costs * High-quality branded equipment at fair prices * Professional refurbishment / inspection & expert cleaning * Tested & fully functional - or your money back * Flexible shipping or self-collection options * Competent advice - before and after purchase * Provision of operating instructions, connection diagrams & spare parts * Inspection according to DGUV V3 Technical data: * L x W x H: 824 x 561 x 1743 mm * Clearance from the lowest tray to the oven opening: 142 mm * Clearance from the top tray to the oven opening: 131 mm * Max. tray height: 1.60 m * Weight: 34.9 kg * Material: Stainless steel * Article number: 60.21.287 Condition: New Shipping: * Delivery or self-collection by arrangement * Worldwide shipping on request * Shipping to islands or mountain stations only by arrangement Subject to changes and errors. Do you have any questions, would like advice, or would like to see something on-site? You can reach us by phone during our opening hours: Monday-Friday 09:00 - 13:00 and 14:00 - 17:00. The sale is exclusively subject to our general terms and conditions (GTC).

Condition: used, - Dimensions: 1970x2150x2730 mm - 2 trolleys: 800x600 mm - Baguette capacity: minimum 360 - Refractory stone (heat accumulator) - Integrated heat recovery unit - Baking surface: 19.2 m² - TOUCHMATIC touch screen control Nsdpfx Amoxxanpeyjcw - Voltage: 400V - Power: 4 kW - Burner: Gas - ALL-IN-ONE = Rotary rack oven with integrated heat recovery unit - No additional trades required for installation - No electrical consumption by the heat recovery unit, as it is 100% mechanical - No need to connect to BMS (Building Management System)/central heating, no buffer tanks to store hot water - Automatic adjustment with no need for control, monitoring, or complex programming - Truly maintenance-free heat recovery unit - Heat recovery on each burner operating cycle - Long service life equal to that of the oven’s heat exchanger - Primary energy consumption reduced by 20% (oil/gas) - Improved baking results due to faster achievement of target baking temperature after loading - Further primary energy savings thanks to shorter baking times - No downtimes (no reheating periods) for continuous baking - Heat remains where it is produced and needed: in the baking chamber, to bake your delicious products

Condition: like new (used), functionality: fully functional, overall weight: 100 kg, System shelf with 4 high-quality caster groups with high load capacity The mobile shelf is ideal as a machine rack or assembly rack The shelf is sold as shown, with a large number of screws and parts. Ncjdpfxownxcgj Amyew Only

Condition: like new (used), functionality: fully functional, This is a tray rack trolley from the premium manufacturer Rational, suitable for the iCombi Pro/Classic combi steamers in size 20-2/1 GN. The trolley comes from a training department and is in almost new condition. RRP (gross): €3,184, our special price: €1,725 gross You will receive an invoice with VAT shown separately. Service: We are happy to assist you in arranging a certified Rational customer service provider. Looking for a specific Rational appliance type? Ask us, we have access to a wide range of used and new equipment. We are happy to advise you on all appliance types. Our used equipment service for you: - 6 months warranty on electrical parts, limited to replacement of defective parts, excluding removal and installation costs - High-quality branded appliances at fair prices - Professional refurbishment / inspection & expert cleaning - Tested & fully functional - or your money back - Flexible choice of shipping or self-collection - Competent advice - before and after the purchase - Provision of user manuals, connection diagrams & spare parts - Inspection in accordance with DGUV V3 Technical data: - W x D x H: 772 x 1742 x 1013 mm - Clearance under lowest position to cooking chamber opening: 118 mm - Clearance above highest position to cooking chamber opening: 148 mm - Max. insertion height: 1.60 m - 17 levels - Max. load capacity: 180 kg - Max. load per level: 30 kg - Tray locking system - Loadable from both sides - Anti-tip protection when removing containers thanks to U-rails - 4 tandem swivel castors (2 with brakes - metal parts in stainless steel) - Drainable and removable drip tray - Rail spacing: 74 mm - Removable handle - Material: stainless steel - Article number: 60.22.396 Capacity: 2/1 GN roasting and baking tray 17 x 2/1 GN grid 17 x 2/1 GN 20 mm deep 17 x 2/1 GN 40 mm deep 17 x Ncodpfx Amjy Aui Eoysw 2/1 GN 65 mm deep 17 x 2/1 GN 100 mm deep 8 x H6-1/1 (up to 1,800g) chicken superspike 12 x H8-1/1 (up to 1,300g) chicken superspike 12 x Other container usage possible: 2/4 GN, 1/1 GN Condition: used, fully functional Shipping: Delivery or collection by arrangement Worldwide shipping upon request Shipping to islands or mountain stations only by arrangement Subject to changes and errors. Do you have questions, need advice, or want to view something on site? You can reach us by phone during our office hours: Monday-Friday 09:00 - 13:00 and 14:00 - 17:00. Sale is exclusively according to our general terms and conditions (GTC).

Condition: used, Rack trolley max. width 1700 mm depth 600 mm height 1800 mm Nodjy Nawbjpfx Amyocw 20 shelves mobile

Condition: used, Mobile rack trolley 3 shelves, middle shelf adjustable Nsdpfx Amsy Naqbsyocw Required space: width 800 x depth 600 x height 1800 mm 20 levels Clear height approx. 10 cm 5 units in stock

Condition: used, This is a rack trolley from the premium manufacturer Rational, suitable for the XXL model combi-steamers SCC/CM/CMP in the 20-2/1 GN size. RRP (gross): €2,400, our special price: €1,495 (gross) You will receive an invoice including VAT. Service: We are happy to assist you in arranging a certified Rational customer service technician. Looking for a specific Rational model? Contact us—we have access to a wide range of new and used equipment. We are glad to advise you on all device types. Our used equipment service for you: • 6 months warranty on electrical parts (limited to replacement of defective components, excluding labor costs) • High-quality branded equipment at fair prices • Professional refurbishment, inspection & expert cleaning • Inspected & fully functional – or your money back • Flexible shipping or self-collection options • Expert advice before and after your purchase • Provision of user manuals, wiring diagrams, and spare parts • Safety inspection according to DGUV V3 Technical data: Dimensions (W x D x H): 772 x 1,016 x 1,717 mm Clearance, lowest tray to cooking chamber opening: 50 mm Clearance, highest tray to cooking chamber opening: 87 mm Max. loading height: 1.60 m 20 tray slots 2/1 GN With container lock Accessible from both sides U-rails 4 tandem swivel castors (2 with brakes – metal parts made from stainless steel) Removable and drainable drip tray Rail spacing: 63 mm Weight: 65 kg Material: Stainless steel Item no.: 60.22.086 Capacity: 20 x 2/1 GN roasting and baking trays, racks 12 x H6-1/1 chicken grill racks (up to 1,500 g) 12 x H8-1/1 chicken grill racks (up to 1,300 g) 12 x H10-1/1 chicken grill racks (up to 950 g) 40 x 1/1 GN, 20, 40, 55 mm deep 12 x 1/1 GN, 65, 90, 100 mm deep Use for other containers: 1/1 GN, 2/4 GN crosswise Corrosion-resistant stainless steel (CNS 1.4301) Condition: Used Shipping: Delivery or self-collection by arrangement Worldwide shipping on request Shipping to islands or mountain locations only by prior arrangement Subject to change and error. Do you have questions, need advice, or would like to view the item in person? You can reach us by phone during our opening hours: Monday–Friday 09:00–13:00 and 14:00–17:00. Njdpfx Amoypcfyeyocw Sale is subject exclusively to our general terms and conditions (GTC).

Condition: good (used), functionality: fully functional, Automatic stacking unit for destacking battens, boards or long goods in kiln trucks. Manufacturer Makor, type ACA 2. Equipped with 2 transfer arms. Part lengths approx. 1600 - 3000 mm (depending on part thickness), maximum part width approx. 170 mm. Installation length approx. 3000 mm. Weight approx. 1500 kg. Ncedpfsyxyfkox Amysw

Condition: used, Year of construction: 1997, functionality: unexamined, total height: 2,500 mm, total length: 33,223 mm, total width: 2,000 mm, table width: 700 mm, input frequency: 60 Hz, input voltage: 460 V, table length: 5,000 mm, table height: 1,200 mm, control cabinet width: 600 mm, control cabinet length: 1,500 mm, control cabinet height: 2,500 mm, compressed air connection: 5.5 bar, Stud & Track Rollforming Machine With 4.5 Tonnes Decoiler & Crane 5 Tonnes Capacity - Fully Dismantled - Ready to be transported MACHINE MANUFACTURER: BRADBURY UK GENERAL SPECIFICATIONS STUD LINE MATERIAL : GALVANIZED COLD ROLLED STEEL MATERIAL STRENGTH : 85.000 PSI MAX YIELD STRENGTH 55.000 PSI MIN· YIELD STRENGTH THICKNESS: 20 GA. TO 16 GA.-"HEAVY GAUGE" 22 GA. TO 25 GA.-"LIGHT GAUGE" ENTRY COIL WEIGHT: 10.000 LB MAX ENTRY STRIP WIDTH: 12" MAX C APPROX. 5" MIN C APPROX. ENTRY COIL I .D: 20" MAX ENTRY COIL O.D: 72" MAX EFF. LINE SPEED : l20-150 FPM-"HEAVY GAUGE" Nsdpjxya Hzofx Amyecw 175-250 FPM-"LIGHT GAUGE" ROLLFORMER SPEED: 120-250 FPM PASS LINE HEIGHT: 51" LINE DIRECTION : RIGHT TO LEFT MODE OF OPERATION : PREPUNCH/POSTCUT CUT LENGTH : 20' MAX. 5· MIN GAUGE" : 90 % C APPROX. ) OF PRODUCT iON < i 6' LENGTH TOLERANCE : •/- 1/16" AT 250 FPM MAIN POWER : ELEC : 460 VOLTS 60 HERTZ 3 PHASE 192.2 FLA : AIR : 80 PSI MIN. CLEAN 6 DRY : HYO : 1500 PSI WORKING PRESSURE CONTROL : 115 VOLT AC AIR CONSUMPTION: 2 CFM MAX. AT 80 PSI

Condition: new, Year of construction: 2022, Jungheinrich, Kongamek support arm trolley Drying boards for carpenters or joiners Jungheinrich article number: 167793-4A several available 3 packages, can be sent 14 layers Support arm diameter 20mm Nsdpfxjvntzxj Amyjcw Installation height 1770mm External dimensions height 1960mm and length 1520mm Frame width and external dimensions depth 860mm Load capacity per level 20kg Own weight 73mm Delivered disassembled

Condition: new, Technical data for the pallet racking system: Racking system: Stow Type: Pal Rack NS Technical data for the installation: Number of racking rows: 01 unit Length per racking row: approx. 30,900 mm Number of bays / racking row: 11 units, each 3,600 mm Number of levels including the base level: 04 units Technical data for the capacity: Pallet spaces per bay: 20 units Pallet spaces per racking row: 220 units Total pallet spaces: 220 units Based on: Load handling unit: Euro pallet EN 13698-1 Dimensions: 1,200 x 800 x 150 mm Overall height including pallet: not specified Nodpjzl D S Eefx Amyjcw Weight per pallet (max.): 500 kg Included in the scope of delivery: 12x pallet racking uprights, new Material color: RAL 5015 blue Profile dimensions: 100 x 65 x 2.50 mm Incl. transverse and diagonal braces, Base plates The uprights are unassembled optionally pre-assembled (bolted frame) 9,800 mm high 1,100 mm deep 88x pallet racking beams, new Material color: RAL 2004 orange Box profile: 140 x 50 mm Beam type: PNB0414|2 Agraffe: 4 HK (hooks) Clear width: 3,600 mm Max. load per beam pair: 2,000 kg with evenly distributed load 176x locking pin, new Material color: Sendzimir galvanized For securing the longitudinal beams against unintentional lifting 48x bolt anchor, new Manufacturer: Hilti Type designation: HST2 M12x105/10 Design: Carbon steel, galvanized Approved for: cracked concrete 24x leveling plate, used Design: fully galvanized for leveling the racking uprights that are installed on uneven ground 01x load sign with information on bay and frame loads, manufacturer and order number Dimensions: 420 x 297 x 3 mm Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Any additional transport or shipping of this item will incur additional costs, which can be requested separately depending on the delivery location or scope of delivery.

Condition: new, Technical data for the pallet racking crossbeam: Racking system: Stow Type: Pal Rack NS Included in the scope of delivery: 01x Pallet racking crossbeam, new Material color: RAL 2004 orange Box profile: 160 x 50 mm Crossbeam type: PNB0436 Clips: 4 HK (hooks) Clear width: approx. 3,300 mm Max. load per pair of crossbeams: 4,500 kg with evenly distributed load Nodpfx Aozlhr Aemyecw 02x Locking pins, used Design: fully galvanized For securing the longitudinal beams against unintentional lifting out Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Any further transport or shipping of this item will incur additional costs, which can be requested separately depending on the delivery location or scope of delivery.

Condition: used, Thread rolling machine UPWS 25. Nodpszd Rf Nefx Amyscw

Condition: new, THREAD ROLLING ROLLERS Ncedpfxezdv Tro Amysw

Condition: used, Year of construction: 2019, functionality: fully functional, Roller Conveyor / Gravity Conveyor / Pallet Roller Conveyor Manufacturer: Rack & Roll Condition: Used Year of manufacture: 2019 Model: Gravity Installation: Consisting of 260.46 meters The system consists of: 30 segments x approx. 2550 mm length Nedpfsyc H Avex Amyocw 18 segments x approx. 2395 mm length 16 segments x approx. 1445 mm length Stock available: approx. 142.73 meters Total width: approx. 1125 mm Roller width/conveying width: approx. 1035 mm Roller/axle spacing: approx. 150 mm Roller diameter: 60 mm Frame: 85/35 mm 1 to 2 brake rollers per segment installed, 80 mm diameter and 25 segments x approx. 2795 mm length 6 segments x approx. 2400 mm length 28 segments x approx. 1195 mm length Stock available: 117.73 meters Total width: approx. 1145 mm Roller width/conveying width: approx. 1055 mm Roller/axle spacing: approx. 125/150 mm Roller diameter: 60 mm Frame: 85/35 mm Material: Galvanized steel 1 to 2 brake rollers per segment installed, 80 mm diameter Price: per meter Internal item number: 2026012401 Features: Condition: Fully operational, with signs of wear Ideal for fast material handling Professionally dismantled and packaged Collection address: Industriestraße 5 (47918 Tönisvorst) The conveyor system was operational up until dismantling. Thanks to the excellent manufacturing quality, your materials glide smoothly to their destination, even under heavy loads. Tailor-made solutions for your intralogistics We are your expert partner for roller conveyors, belt conveyors, incline conveyors or telescopic conveyors for loading and unloading goods! We are happy to provide a customised quote or assist you with layout or installation inquiries. Just let us know your requirements and onsite conditions. Benefit from our many years of experience and extensive network of specialists. We have successfully implemented projects for companies across a broad range of industries, including logistics, pharmaceuticals, trades, and electronics. Let us work together to develop cost-effective and sustainable ways to optimise your processes and material flow. We can also offer fully automated sorting solutions and complementary components such as picking shelves or bins.

Condition: used, Year of construction: 2019, functionality: fully functional, Removal/Feed Unit, Pallet Roller Conveyor/Roller Conveyor Manufacturer: Rack & Roll Condition: Used Year of Manufacture: 2019 Model: Gravity Segment Length: approx. 2395 mm Total Width: approx. 1145 mm Roller/Conveyor Width: approx. 1055 mm Roller/Axle Spacing: approx. 100 mm and 150 mm Roller Diameter: 60 mm Frame: 85/35 mm Material: Galvanized steel Up to 2 brake rollers per segment Stock quantity: 28 units Price per unit Internal Item Number: 2026012601 Features: Condition: Fully functional, with signs of use Ideal for fast material transport Professionally dismantled and packaged Collection Address: Industriestraße 5 (47918 Tönisvorst) The conveyor system was in operation until dismantling. Thanks to the excellent workmanship of the conveyor technology, your material glides smoothly to its destination, even under heavy loads. Ncedpfx Aoydfugemyjw Tailor-made solutions for your intralogistics For roller conveyors, belt conveyors, inclined conveyors, or telescopic conveyors for loading and unloading your goods, we are your competent partner! We are happy to provide you with an individual quotation or advise you on planning or installation matters. Simply let us know your requirements and site conditions. Take advantage of our many years of experience and our excellent network of professionals. We have already successfully implemented projects for companies in a wide range of industries, such as logistics, the pharmaceutical industry, trades, and the electronics sector. Together, we will find solutions to optimize your processes and material flow cost-effectively and sustainably. We can also offer you fully automated sorting systems or supplementary components such as order-picking racks or bins.

Condition: used, Year of construction: 2019, functionality: fully functional, Pick-up/discharge unit, pallet roller conveyor/roller conveyor Manufacturer: Rack & Roll Condition: Used Year of manufacture: 2019 Model: Gravity Segment length: approx. 2375 mm Ncsdpfsydfuyox Amysw Overall width: approx. 1125 mm Roller/conveyor width: approx. 1035 mm Roller/axle spacing: approx. 100 mm and 150 mm Roller diameter: 60 mm Frame: 85/35 mm Material: galvanized steel Up to 2 brake rollers per segment Stock: 20 units Price per unit Internal item number: 2026012602 Features: Condition: fully functional with signs of use Ideal for fast material handling Professionally dismantled and packaged Pick-up address: Industriestraße 5 (47918 Tönisvorst) The conveyor system was in operation until dismantling. Due to the excellent manufacturing quality, your material will glide smoothly to its destination, even under heavy loads. Tailor-made solutions for your intralogistics We are your competent partner for roller conveyors, belt conveyors, inclined conveyors, or telescopic conveyors for loading and unloading your goods! We are happy to prepare a customized offer for you or provide technical advice on planning and installation. Simply let us know your requirements and local conditions. Take advantage of our many years of experience and our outstanding network of specialists. We have already successfully completed projects for companies from various sectors, such as logistics, pharmaceuticals, trades, and the electronics industry. Together, we will find cost-effective and sustainable solutions to optimize your workflow and material handling. We can also offer you fully automated sorting systems or complementary components such as picking racks or containers.

Condition: good (used), clear span: 1,400 mm, total length: 7,510 mm, shelf height: 1,750 mm, Technical data for the pallet racking system: Rack system: Stow Model: Pal Rack NS Technical data for installation: Number of rack rows: 01 unit Length per rack row: approx. 7,510 mm Number of bays per rack row: 05 units á 1,400 mm Number of levels plus ground level: 02 units Scope of delivery includes: 06x pallet rack uprights, used Material color: RAL 5015 sky blue Upright type: PNFB12 Profile dimensions: 85 x 65 x 1.75 mm Including horizontal and diagonal bracing, base plates The uprights are pre-assembled (bolted lattice construction) 1,750 mm high 1,100 mm deep 20x pallet rack beams, used Material color: orange U-profile: 150 x 50 x 3.00 mm Connector: 4 HK (hooks) Design: header beam Clear opening: 1,400 mm 40x safety pins, used Material color: Sendzimir galvanized Ncsdpfx Aew I R Slsmyjw For securing the cross beams against accidental lifting 24x wedge anchors, new Manufacturer: Hilti Model: HST2 M12x105/10 Material: carbon steel, galvanized Approved for: cracked concrete 12x shimming plates, used Finish: fully galvanized For leveling rack uprights positioned on uneven floors 01x load sign With information on bay and compartment loads, manufacturer, and order number Dimensions: 420 x 297 x 3 mm General information about the item: This item is only offered for collection. If transport or dispatch is required, additional costs will be incurred, which can be quoted separately depending on delivery location and scope.

Condition: good (used), clear span: 1,450 mm, total length: 7,760 mm, shelf height: 1,750 mm, Technical details for the pallet racking system: Racking system: Stow Type: Pal Rack NS Technical setup data: Number of rack rows: 01 pc. Length per rack row: approx. 7,760 mm Number of bays per rack row: 05 pcs. at 1,450 mm each Number of levels plus ground level: 02 pcs. Currently in stock: approx. 2 sets! Scope of delivery includes: 06x pallet rack frames, used Material color: RAL 5015 sky blue Frame type: PNFB12 Profile dimensions: 85 x 65 x 1.75 mm Including horizontal and diagonal braces, base plates Frames are pre-assembled (bolted construction) 1,750 mm high 1,100 mm deep 20x pallet rack beams, used Material color: orange Beam type: PNBH0443/1.5 Box profile: 130 x 50 mm Connector: 4 hooks Design: box end beam Clear width: 1,450 mm 40x locking pins, used Material color: sendzimir galvanized For securing the beams against accidental lifting 24x wedge anchors, new Manufacturer: Hilti Model: HST2 M12x105/10 Material: carbon steel, galvanized Nodpfx Amow I Sx Teyecw Approved for: cracked concrete 12x leveling shims, used Design: fully galvanized For leveling rack frames installed on uneven floors 01x load plate With information on bay and compartment loads, manufacturer, and commission number Dimensions: 420 x 297 x 3 mm General information about the item: This item is only offered for collection. Any requested transportation or shipping of this item is associated with additional costs, which can be provided upon request depending on the delivery location and scope.