Used Punching Press for sale (13,114)

Condition: used, Year of construction: 2006, Pressing force 100 t diameter 40 mm throat 760 mm total power requirement 8,5 kW weight 3.600 kg Accessories / equipment: - punching table Iiodpfx Abjyv Nrzonof

Condition: used, Year of construction: 2000, pressure 100 t throat 620 mm stroke 0-100 mm hole diameter in sheet thickness 40 in 20 mm Isdjyv Ncyjpfx Abneif no. of strokes 49 Hub/min total power requirement 15 kW weight of the machine ca. 3.500 kg

Condition: used, Punching Machine MUHR & BENDER - MUBEA Type KL 350 / 203 Machine No. Year of manufacture 19 Punching force 35 tons Throat depth 203 mm Ram stroke 22 mm Capacity Ø 28 mm in 10 mm sheet (at 450 N/mm²) Ø 23 mm in 12 mm sheet (at 450 N/mm²) Ram plate 117 x 70 mm Table plate 175 x 100 mm, thickness 100 mm Drop-through opening in table cutout Ø 56 mm Stroke release Single stroke via foot switch Motor power 1.5 kW Power supply 400 Volt, 50 Hz Ijdjyvvkwepfx Abnjif - Electric foot switch for stroke release - Manual lever positioning device for punch movement - Equipped with a Ø 8 mm punching tool - Support tables approx. 270 x 230 mm each on left and right of punching unit - Metal base frame Space requirement L x W x H 750 x 720 x 1500 mm Weight 430 kg In very good condition

Condition: used, Single-Column Eccentric Press RASTER ZEULENRODA Type PDA 100 Year of manufacture: 1995 Pressing force: 100 tons Throat depth: approx. 360 mm Table size: 1200 x 710 mm Ram area: 900 x 500 mm Table opening: 400 x 120 mm Stroke adjustment: 6 to 82 mm Ram adjustment: 100 mm Installation height, max. stroke, ram Top Dead Center (TDC): max. 469 mm Installation height, max. stroke, ram Bottom Dead Center (BDC): max. 387 mm Strokes per minute: 50-200 s.p.m. Main drive motor power: 18.5 kW Power supply: 400 Volt, 50 Hz - Hydraulically actuated multiple-disc wet clutch and spring-loaded safety brake - Infinitely variable drive via PIV gearbox with inching mode for automatic stroke adjustment and setup operations - Hydraulic overload protection in the ram - Press force and process monitoring via UNIDOR APS - Pneumatic, steplessly adjustable ram weight compensation - Roller feeder MABU WE16, 160 x 3 mm, programmable feed length - Central grease lubrication - Operating manual and documentation for the press Included: Roller feed unit MABU Type WE16 Strip width: 160 mm Iedpfxox U Eiao Abnsif Strip thickness: max. 3 mm Strip cross-section: max. 300 mm² Roller diameter: 63 mm Strip speed: 40 m/min - Adjacent feeder control MABU Space requirements for eccentric press L x W x H: 270 x 240 x 350 cm Weight of the press: 13.5 tons

Year of construction: 2026, condition: new, Bosporas Machinery is a manufacturer of coil processing, press feeding and metal forming systems, delivering high-performance and customized industrial solutions worldwide. Our press solutions are designed for punching, perforating, embossing and sheet metal forming applications. Depending on production requirements, we offer advanced servo punch press systems for flexible programmable production and high-speed mechanical presses for continuous mass production. These machines can be supplied as standalone units or integrated into complete coil-fed automatic production lines. ⚙️ AVAILABLE PRESS SOLUTIONS 🔹 SERVO PUNCH PRESS The Servo Punch Press is designed for precision, flexibility and intelligent production control. Key Features: 40 Ton punching capacity 6 tool stations for multi-tool operation Dual-servo controlled X-Y punching system Punching at programmable coordinates 22 kW hydraulic punching drive Up to 90 strokes per minute Automatic scrap conveyor system Advantages: High precision punching performance Programmable motion profiles Lower noise and reduced maintenance Energy efficient operation Fast setup for different part designs 🔹 PERFORATION HIGH SPEED MECHANICAL PRESS The High-Speed Mechanical Press is ideal for continuous perforation, embossing and repetitive punching operations in mass production environments. Isdpfoy Anr Tjx Abnoif Suitable For: Sheet metal punching Perforating Embossing Tool & die applications High-volume production lines Advantages: High production speed Stable continuous operation Reliable mechanical drive system Ideal for repetitive operations Cost-effective mass production solution 🔧 ENGINEERING FEATURES Robust industrial machine construction PLC & HMI control systems Easy integration with feeders and automation lines Tooling flexibility based on product design Long service life and low maintenance structure ⚡ OPERATIONAL ADVANTAGES Two technologies for different production needs Flexible solutions from custom parts to mass production Standalone or turnkey line integration Improved efficiency and reduced downtime Short lead time compared to European manufacturers 🏭 APPLICATION AREAS Sheet metal manufacturing Perforated panel production Electrical cabinets HVAC products Construction components Automotive parts White goods industry 🧩 OPTIONAL CONFIGURATIONS Coil feeding integration Decoiler & feeder systems Custom dies and tooling Conveyor systems Automation upgrades Turnkey production solutions 📸 REFERENCE PROJECTS Images and videos can be shared showing different press systems successfully operating in various industrial applications. Additional references and technical details are available upon request.

Year of construction: 2001, condition: ready for operation (used), functionality: fully functional, punching force: 1,000 t, operating speed: 93 mm/s, stroke length: 55 mm, table length: 1,100 mm, table width: 800 mm, machine/vehicle number: 100597, TECHNICAL DETAILS Press force: 10,000 kN Table surface (W x D): 1,100 x 800 mm Stroke range: 15 - 55 mm Clearance at max. stroke: 28 - 98 mm Puzzle thickness: up to 3 mm Format width (max.): 1,100 mm Punching speeds Upwards: 47.8 mm/s Downwards: 93.7 mm/s Punching: 0.28 mm/s Hydraulic unit Type: 250 Dimensions (L x W): 1,310 x 910 mm Oil capacity: 670 l Unit weight: 1,000 kg Oil weight: approx. 550 kg Weight with oil fill: approx. 1,550 kg Automatic punching table Type: 355 Table top size (W x D x thickness): 1,000 x 700 x 10 mm Hardness: 62 HRC Surface finish: 7 MACHINE DETAILS Electrics Operating voltage: 400 V Frequency: 50 Hz Rated machine current: 50 A Incoming line protection: 63 A Control voltage: 230/24 V Rated power: approx. 30 kW Protection class: IP 54 Power requirement: approx. 8 kW Pneumatics Operating pressure: 6 bar Dimensions & Weight Puzzle disassembler dimensions (L x W x H): 3,150 x 1,620 x 2,900 mm Working height: approx. 1,700 mm Iodpfjy Ampdsx Abnsif Total weight: 33,000 kg Weight of puzzle disassembler: approx. 1.8 t Noise level: < 70 dB(A)

Condition: used, Eccentric stamping press HAULICK + ROOS, Type RVD 125 Double-column eccentric press Machine No. 212560, Year of manufacture 1981 Pressing force 125 tons Table size 880 x 800 mm Table opening 470 x 140 mm Column distance 900 mm Column distance, side 415 mm Ram stroke 45 mm Ram adjustment range 0-80 mm Installed height as shown in the picture 340 mm Stroke rate 50 to 300 strokes/min Motor power, main drive 22 kW Power connection 380 volts, 50 Hz - Double connecting rod drive with 4-bearing eccentric shaft for off-center ram pressure load - Adjacent electrical cabinet - NC roller feed EBU, width 250 mm, year of manufacture 2003 - Adjacent control panel for the roller feed - Strip feed direction from left to right Space requirement (press) L x W x H 3000 x 2000 x 3020 mm Transport height 2950 mm Isdpjhlnzkefx Abnsif Weight of the press approx. 11 tons

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection Iodpok S Htxjfx Abnoif - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: ready for operation (used), functionality: fully functional, FOR SALE: BRUDERER BSTA 60 High-Speed Stamping Press With Automatic Strip Feeder BBV 300/200 600 kN | 100–800 spm | Fully automatic | Top-tier Swiss quality Iijdpfxoxz Ugxo Abnsf Technical Highlights: Nominal force: 600 kN Stroke rate: 100–800 strokes per minute Max. feed length: 200 mm. Year: Unknown (No ID Plate) / Tested under power: 2025 Drive power: 30 Hp Control voltage: 24V AC Power connection: 440VAC / 50Hz Adjustable stroke: 20 / 25 / 31 / 38 / 45 /51 / 58 / 64 / 70 / 76 mm Shut/Ram height adjustment: 80 mm Working Dimensions: Max tool installation width: 620 mm Strip pass width: up to 320 mm Ram area: 800 × 500 mm Table area: 620 × 680 mm Max strip width: 300 mm Max feeding pitch: 200 mm Max material thickness: 6 mm Feeding angle: 180 Deg Machine Dimensions: Machine footprint (L × W × H): 2210 × 2075 × 2190 mm Weight (approx.): 8,000 kg Equipment Includes: Feeder BBV 300 – fully synchronized mechanical strip feeder system Integrated control cabinet Pneumatic clutch and brake Adjustable stroke and shut height Compressed air connection: 6–10 bar Oil cooling unit included Ready for integration with peripheral systems Machine in excellent technical and visual condition Fully tested Immediate availability from Europe Worldwide shipping available Contact us today for pricing and further technical details. Let us help you upgrade your production line with Swiss precision engineering.

Condition: used, functionality: fully functional, Year of construction: 2004, operating hours: 26,426 h, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, punching force: 20 t, The punching machine is in good condition and has always been serviced on time by certified Amada service representatives. All documentation is included. The drum encoder was recently replaced. The machine is sold complete with software and tools. The punching machine is connected and can be tested on site. Specification: Year: 2004.07 Made in: France Operating hours: 26,426 Power-on hours: 65,006 Control unit: AMADA AMNC-F Punching force: 20 tons Stations: 45 Tools: sold with tooling Software: Linea 5 / Combi 5 (Only works with Windows XP) Sheet length: 2,500 mm Sheet width: 1,270 mm Sheet thickness: 3.2 mm Sheet repositioning: 5,000 mm Workpiece weight: 150 kg Dimensions: L 6080 x W 5120 x H 2318 mm Weight: 16,500 kg Location: Lithuania Test possible: Yes If you have further questions, we will be happy to answer them. Iiodpfx Asw E Emaebnsf

Condition: used, Die-cutting machine – Swivel frame die-cutting machine – Flatbed die-cutting machine – Toggle press – Eccentric press Die-cutting machine + feeder for use with strip-type die-cutting tools Flatbed die-cutting machine HELMERDING, type PSH 25 Item no. EP 97784, Machine no. 6073, Year of manufacture 1998 Pressing force 25 tons Distance between tie rods 700 mm Table area = installation space 800 x 670 mm Table area = installation frame, width 510 x depth 440 mm, plate thickness 20 mm Punch area 800 x 670 mm Iodpfxodzqmzs Abnjif Through-hole in the table 490 x 420 mm Punch stroke 45 mm Punch adjustment distance 10 mm Installation height = tool height 100 mm Stroke rate up to 250 strokes/min Motor power 15 kW Mains connection 400 volts, 50 Hz - controlled drive for stepless stroke rate adjustment - pneumatic clutch-brake combination - punch equalizing cylinder - automatic central lubrication system VOGEL - massive base plate with 4 vibration damping elements under the machine Space requirement L x W x H approx. 3000 x 2000 x 3000 mm Weight 4.5 tons Good condition Previously, the machine was used for die-cutting cardboard sheets. Ideal for die-cutting non-woven fabrics or similar materials for respiratory masks.

Condition: used, Pneumatic press, compressed air press BOSCH Type Manufacturer’s No. Year of manufacture 1980 Pressing force: 18 kN = 1.8 tons at 5 bar 15 kN = 1.5 tons at 4 bar 12 kN = 1.2 tons at 3 bar 8 kN = 0.8 tons at 2 bar 6 kN = 0.6 tons at 1.8 bar Overhang: 100 mm Ram stroke: 70 mm Table surface: 245 x 200 Ram surface: Ø 45 mm Iodpfsh U Dtuex Abnjif Maximum installation height: 235 mm Arbor hole: Ø 20 mm with clamping screw Compressed air requirement: 5 bar - Pressing force can be continuously adjusted via a pressure regulator - Pneumatic cylinder with ram, height adjustable by 90 mm - Pneumatic two-hand operation - Mounted on a metal frame with wooden plates Space requirement L x W x H: 1050 x 700 x 1600 mm Weight of pneumatic press: 82 kg Weight with table frame: 140 kg In good condition

Condition: used, Single-column – Eccentric press PELS - RICHTER, type PEKR 125 Machine no. 20684, year of manufacture 1967 Pressing force: 125 tons Reach: 430 mm Table size: 1100 x 750 mm Ram surface: 890 x 650 mm Table opening: Ø 400 mm Stroke adjustment: 6 to 115 mm Ram adjustment: 100 mm Installation height for maximum stroke at the top: max. 450 mm Iedpefim Thjfx Abneif Arbor hole: Ø 50 mm Stroke rate: 60 strokes/min Table height above floor: 900 mm Motor power: 7.5 kW Power connection: 380 volts, 50 Hz - Overload protection by shear plate in the ram - Compressed air coupling-brake combination DESCH - Ram weight balancing cylinder - Manual ram adjustment - Two-hand operation - Cam indexing mechanism - Central grease lubrication system Vögele - Stroke counter Space requirement L x W x H: 2300 x 1450 x 3030 mm Weight: approx. 10 tons Good condition

Condition: new, punching pressure 28.0 t punching cross-cut in cmm 31 in 7.0 mm ST throat 250 mm dayligth 223 mm no. of strokes 10 - 30 Hub/min oil volume 32.0 ltr. work height max. 1033 mm total power requirement 3.0 kW weight of the machine ca. 553 kg dimensions of the machine ca. 730 x 540 x 1530 m Furnishing: - Punch quick-change device up to Ø 31 mm - green series - installed: round punch no. 5 Ø 25.0 mm and round die no. 3 Ø 25.7 mm - Free: LED lighting in the punching area - Swiveling scraper (plates exchangeable) - Various material support tables are available separately - Brace - 2-step foot switch, with double press for grain search function - electrical controls - Stroke length and stroke position continuously adjustable - integrated hydraulic unit with oil filling - Performance specifications apply to a material strength of 450 N/mm² - Main connection cable and plug for 16 amps are not included in the scope Iisdpfx Asw U U S Nebnef of delivery

Condition: used, Single-column hydraulic press, straightening press, punching tool – ECKOLD Press frame with hydraulic cylinder, mobile press, punching unit Type RSD 1500 - 125 Machine No. 317 / 690 Year of manufacture approx. 1986 Pressing force 150 tons Stroke 125 mm Ram stroke 35 mm Table size 280 x 210 mm Ram surface Ø 125 mm Installation height (ram to table) max. 265 mm Iiodpfx Aod Swtajbnef Table height above floor 403 mm Hydraulic operating pressure max. 500 bar - without hydraulic unit - Ram surface with 4 threaded holes M16 and 20 mm guide groove, with a centering bore Ø 15 mm in the center - 1 high-pressure hydraulic hose with external thread M30x1.5 mm, hose length 4 meters - 1 high-pressure hydraulic hose with union nut M30x1.5 mm, hose length 4 meters Space requirement L x W x H 700 x 300 x 1450 mm Weight 1250 kg Good condition

Condition: used, Single-column eccentric press KRUPP, type PEKRD 125 h Machine No. 2861, Year of manufacture 1977 Pressing force: 125 tons Reach: 400 mm Table size: 950 x 750 mm Ram area: 800 x 540 mm Table opening: 100 x 250 mm Stroke adjustment: 8 to 160 mm Iiodpfx Aedzqddebnsf Ram adjustment: 100 mm Installation height for maximum stroke at the top: max. 550 mm Stroke rate: 60 strokes/min. Table height above floor: 800 mm Motor power: 10 kW Power connection: 380 volts, 50 Hz - Hydraulic overload protection in the ram - Pneumatic clutch and brake combination ORTLINGHAUS - Ram weight compensation cylinder - Motorized ram adjustment - Tabletop with ball bearings - Two-hand operation - Central lubrication system HELIOS - Stroke counter - UVV 7n 5.1 §4a, paragraph 2, No. 3b for manual feeding operations Space requirement L x W x H: 2300 x 1800 x 3200 mm Weight: approx. 10 tons Good condition (very little use)

Condition: ready for operation (used), pressure 30.0 t Iedpfx Abjxaaipsneif punching cross-cut in cmm 30.0 in 9.0 mm stroke ca. 35 Hub/min throat 610 mm stroke - stepless adjustable 0 - 28.0 mm oil volume 35.0 l work height max. 1010 mm total power requirement 4.0 kW weight of the machine ca. 1200 kg. range L-W-H 1400 x 700 x 1600 mm good condition (!!) with a lot of application tools (stamps/dies) Furnishing: - electro-hydraulic hole punch, with large throat - Material/sheet metal scrapers including scraper plates - Large material support table, with adjustable depth stops - continuous stroke adjustment - freely movable foot switch including protective cover - Forklift pockets for easy transport - side storage area - lots of accessories + tools - including tool cabinet - Matrix base (for special size matrices) - Stamp holders (for special size stamps) - original user manuel

Condition: used, Year of construction: 1991, pressure 70.0 t punching cross-cut in cmm 27 in 20 mm punching cross-cut in cmm 32 in 14 mm work height max. 1060 mm column arm 500 mm weight of the machine ca. 1500 kg. total power requirement 7.0 kW range L-W-H 1550 x 1200 x 1950 mm good / well-maintained condition (!!) New price approx. 21.000 euros Special price on request Equipment: - electro-hydraulic hole punch, with large projection Ijdpfx Ajxabu Tsbnoif - large GEKA stop table with movable stop system - sheet metal stripper with stripper plates - stepless stroke adjustment - die base - 1x freely movable foot switch - operating instructions (PDF)

Condition: used, pressure 100 t punching cross-cut in cmm Ø 31 in 25 mm Iijdpfxjxabrfj Abnof stroke 10 - 50 mm column arm 510 mm work height max. 1100 mm no. of strokes 14 - 45 Hub/min punch diameter max. Ø 90.0 mm oil volume 103 l total power requirement 7.5 kW weight of the machine ca. 2400 kg. range L-W-H 1750 x 1020 x 2050 mm maintained condition (!!) New price without accessories approx. 25.000 euros Special price on request Furnishing: - heavy / robust electro-hydraulic hole punch, with large throat - Punching station with material/sheet metal scraper - stepless stroke adjustment .. 10-50 mm - freely movable foot switch including protective cover - hydraulic low pressure finder for foot switch operation - Crane hanging eye for easy transport - side storage area - Hydraulic unit, integrated - Three-phase motor, 400 volts, 50 Hz - original instruction manual

Condition: new, Year of construction: 2025, Sliding clip formers are used to produce fixation sliding clips for double standing seam roofing panels. Before installation roofing panels have to be made using roll former roofing machines. After finishing of panels production and preparing roofing works panels can be installed on roofing place with special fixation clips. Those clips, depending on design, could be fixed or sliding ones. Fixed clip has simple and cheap design so it can be good for small roofs that doesn’t have long length panels. Sliding clip are good for big roofs with different designs and long-length panels. Sliding clips can move and self-find perfect position so not be damaged and safe for roof while temperature expansions. We offer punching presses for making both fixed and sliding clips. We make sliding clip formers for 25, 27 or 39mm clip highs Isdpjqxalxefx Abnsif For sliding expansion clips productions there have three presses to be used. First sliding clip bottom part press is used for punching bottom part of sliding clip with fixation round holes and connection oval hole. At the same time this press cuts metal strip with necessary length. Blank for clip production is easy to get using manual guillotine or cut-to-length slitting machine. Second sliding clip bottom part bender is used for bending of sliding clip bottom part to 90 degrees angle. So, after this operation bottom part is ready. Third clip former makes top part of sliding clip at the same time forming and bending it. After producing bottom and top part of sliding clip you can easily connect it to one working sliding clip. So using sliding clip formers that we offer you can easily make expansion clip and use it while double standing seam roofing installation without any unnecessary deformations. Maximum metal thickness you can work with -1mm. To get more information about sliding clip former we produce please contact our sales department.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2008, operating hours: 72,918 h, laser power: 2,700 W, punching force: 22 t, sheet thickness (max.): 6 mm, sheet thickness steel (max.): 8 mm, sheet thickness aluminum (max.): 4 mm, TECHNICAL DETAILS Combined punching/laser operation: 2,585 x 1,650 mm Punching mode: 3,085 x 1,740 mm Laser operation: 3,085 x 1,650 mm Outputs Laser power: 140 - 2,700 W Maximum sheet thickness: 8 mm Cutting capacity for mild steel: 8 mm Cutting capacity for aluminum: 4 mm Cutting capacity for stainless steel: 6 mm Maximum punching force: 220 kN Active hold-down device (programmable in stages): 4.5 - 20 kN Maximum workpiece weight: 230 kg Speeds Maximum positioning speed X-axis: 90 m/min Y-axis: 60 m/min Simultaneous (X and Y): 108 m/min C-axis punching: 60 revolutions/min Thread forming: 180 revolutions/min Punching stroke sequence (E = 1): 900 1/min Marking: 2,800 1/min Isdpfjw Suwyox Abneif Tools Linear magazine: 18 tools with 3 clamps Tool change time: 1.5 - 5 s Tool accuracy Position deviation: ±0.10 mm Average position spread: ±0.03 mm Programmable slides for punched and laser parts (max.) Size: 500 x 500 mm TRUMPF CNC control: based on Siemens Sinumerik 840D MACHINE DETAILS Laser switch-on time: 72,918 h Cutting time: 18,536 h Space requirement (width x length): 7,900 x 9,100 mm Height: 2,400 mm Weight: 22,500 kg Laser gas consumption CO2 / N2 / He: 1 / 6 / 13 l/h Connected load: 73 kVA

Condition: used, Year of construction: 1980, control panel Boschert Stanze Year 1990 +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. Iiodpfxjx U A H Ns Abnef +++++

Year of construction: 2006, operating hours: 46,547 h, condition: excellent (used), functionality: fully functional, Laser punch press Trumpf TruMatic 6000 L with TrumaLift SheetMaster, ToolMaster and GripMaster as well as and scissor lift table. SheetMaster: not only loads and unloads the machine, it also sorts the parts the parts reliably ToolMaster: automatically changes the tools quickly, safely and conveniently GripMaster: reliably moves residual grids and strips TECHNICAL DETAILS working area: 2585 x 1280 mm Control: Siemens Sinumerik 840 D laser power: 3200 watt sheet thickness mild steel: max. 8 mm sheet thickness stainless steel: max. 8 mm sheet thickness aluminum: max. 4 mm workpiece weight: max. 200 kg Accuracy: +/- 0.1 mm Iiedpfx Abon Nxw Djnef Punching force: 22 t punching diameter: max. 76,2 mm C-axis punching: 330 rpm stroke sequence: 450 - 1000 1/min stroke sequence marking: 2800 1/min MACHINE DETAILS Laser switch-on time: 46,547 h cutting time: 23.580 h length: 7500 mm width: 8100 mm height: 2400 mm Weight: 16000 kg (basic machine) Operating voltage: 400 V / 50 Hz Connected load: 76 kVA

Year of construction: 1997, condition: good (used), Used fully serviced and good condition Trumpf 500r cnc punch press for sale TRUMPF TRUMATIC T500R Large format rotation cnc punch press for sale Isdohtfp Tjpfx Abnsif Fully serviced Machine capable of taking multi tool Complete with tool holders and tools including multi tools Complete with Retractable clamps 3metre x 1.5metre sheet without reposition. Additional extras with the machine: Cabinet full of tooling Multitool Multiset – tool setter Quickload Quick sharp tool grinder Trumpf TC 500R Turret Punch 3000 X 1500mm large format machine 1600 throat x 3metre rail. TRUMPF TRUMATIC 500 CNC PUNCH WITH CONTROL & AIR TABLE CAPACITY: 220KN SERIAL YEAR: 1997

Condition: refurbished (used), Year of construction: 2026, functionality: fully functional, machine/vehicle number: 8923, total height: 4,200 mm, ram adjustment: 100 mm, installation height: 650 mm, total width: 3,100 mm, total length: 2,000 mm, pressing force: 320 t, clearance between the columns: 1,530 mm, overall weight: 38,000 kg, DGUV certified until: 01/2027, year of last overhaul: 2026, punching force: 320 t, The machine is fully overhauled and completed. The control system is built according to customer specifications (Siemens control). Iodpex U Tudofx Abnoif Column gap: 1530 mm Distance table – ram: 650 mm Ram adjustment: 100 mm Stroke adjustment: 20 – 160 mm Ram strokes per minute: 30 – 120 Delivery time approx. 3 – 4 months after configuration of the new control system based on customer-specific requirements. Price on request