Used Painting Room for sale (5,002)

Year of construction: 2020, condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. TSE 20.20 Dry splash wall Dimensions: 2000 x 2000 mm W X H Fan is installed above the wall + Fan in the height Air capacity: 7,200 m³ / h Motor: 0.75 kW explosion-proof (ATEX) Exhaust air pipe: 500 Ø mm depth: 900 mm The pipeline should not exceed a total length of 3-4 meters. Double filtration: paper filter + Paintstop filter mat over Terminal strip (+150,- EUR net) Options/additional price for: Paintstop filter mat terminal strip: 150,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Kodpfefv Hiqjx Ad Newt Just contact us.

Year of construction: 2020, condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. TSWi 30.20 Dry splash wall Dimensions: 3000 x 2000 mm W X H Fan is built into the wall Air capacity: 10.800 m³ / h Motor: 2,20 kW ex-proof Exhaust air pipe: 500 Ø mm depth: 900 mm Double filtration: paper filter + Paintstop filter mat over Terminal strip (+180,- EUR net) Options/additional price for: Kwjdpfjfr T Emsx Ad Not transition angular to round: 150,- EUR net Paintstop filter mat terminal strip: 180,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Just contact us.

Year of construction: 2020, condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. Kedpfx Aofr T Eqed Newt We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. TSWi 20.20 Dry splash wall Dimensions: 2000 x 2000 mm W X H Fan is built into the wall Air capacity: 7,200 m³ / h Motor: 1,50 kW ex-proof exhaust air pipe: 400 Ø mm depth: 900 mm Double filtration: paper filter + Paintstop filter mat over Terminal strip (+150,- EUR net) Options/additional price for: transition angular to round: 150,- EUR net Paintstop filter mat terminal strip: 150,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Just contact us.

Condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. Kwedpfx Aofn Ndcjd Not We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. TSWc 20.20 Dry bulkhead Dimensions: 2000 x 2000 mm W X H + Fan in the height Air capacity: 7,200 m³ / h Motor: 1,50 kW ex-proof exhaust air pipe: 400 Ø mm depth: 900 mm Double filtration: paper filter + Paintstop filter mat over Terminal strip (+150,- EUR net) Options/additional price for: Paintstop filter mat terminal strip: 150,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Just contact us.

Year of construction: 2020, condition: refurbished (used), Dear customers! Our experience has shown that the communication by e-mail usually drags out everything unnecessarily. We would like to help you quickly, but it is better to spend three minutes on the phone than three days writing e-mails back and forth. T.S.W.C. 30.20 Dry bulkhead Dimensions: 3000 x 2000 mm W X H + Fan in the height Air capacity: 10.800 m³ / h Motor: 2,20 kW ex-proof Exhaust air pipe: 500 Ø mm depth: 900 mm Double filtration: paper filter + Ksdpfxefn Nddo Ad Nswt Paintstop filter mat over Terminal strip (+180,- EUR net) Options/additional price for: Paintstop filter mat terminal strip: 180,- EUR net side baffle plates with hinge: 590,- EUR net Pictures may vary. We can also offer you complete spraying rooms with supply air system, heat exchanger, supply air ceiling, piping etc. Just contact us.

Condition: excellent (used), Complete Grinding Room for bandsaw blades Kjdpfx Adskx E Sds Njwt

Condition: good (used), Paint unit, paint pump GRACO MERKUR + Graco G40 gun. Kwjdpfxeulc S Rs Ad Nst

Condition: new, Year of construction: 2026, Heating capacity / nominal heat output: 21 kW Kwjdpfohvibzjx Ad Njt For rooms up to approx. 300 to 500 m³ (according to DIN 4108) Flue pipe outlet: rear side (standard) Flue pipe: Ø 180 mm Filling volume: 80 ltr Required chimney draft min. 12 Pa Mass of the filling opening (L x W) 300 x 340 mm Weight: 375 kg Efficiency 88,2 Energy efficiency class: A+ EWI-A 15G space heaters are type-tested according to DIN EN 13240, according to 15a B-VG (Austria) and LRV (Switzerland). They comply with the limit values of the 1st BImSchV. (Federal Immission Control Ordinance)

Condition: new, Year of construction: 2026, Heat output / nominal heat output: 17.8 kW For rooms up to approx. 300 - 400 m³ (according to DIN 4108) Kwjdpfjdlmnnjx Ad Net Filling volume: 78 ltr Mass of the filling opening: Ø 215 mm Flue outlet: rear side (standard) Flue pipe Ø 180 mm Required chimney draught min. 13 Pa Weight: 250 kg Efficiency: 79,02 Energy efficiency class: A The room heaters GRA-N are type-tested according to DIN EN 13240, according to 15a B-VG (Austria) and LRV (Switzerland). They comply with the 1st BImSchV (Federal Immission Control Ordinance) stage 2.

Condition: new, Year of construction: 2026, Heat output / nominal heat output: 16.5 kW For rooms up to approx. 300 to 400 m³ (according to DIN 4108) Flue pipe outlet: rear side (standard) Flue pipe: Ø 180 mm Filling chamber volume: 80 ltr Required chimney draught min. 12 Pa Dimensions of the filling opening (L x W) 300 x 340 mm Weight: 370 kg Efficiency 85,88 Kodpfjdlmn Hsx Ad Nswt Energy efficiency class: A+ The EWI-A 15 space heaters are type-tested according to DIN EN 13240, according to 15a B-VG (Austria) and LRV (Switzerland). They comply with the 1st BImSchV (Federal Immission Control Ordinance) stage 2.

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, Paint/spray wall dimensions without fan and control Panel! Extraction surface - dimensions (mm): 2190w)x2350(h) Overall dimension(mm): 2295(w)x2295(h)x810(d) Technical data: - Fan power 2.2kW (ATEX) - Fan suction capacity: 12000 m³/h (max 1100Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX Kwsdpfx Asia Ta Asd Not - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, Paint/spray wall dimensions without fan and control Panel! Extraction surface - dimensions (mm): 3000(w)x1400(h) Overall dimension(mm): 3100(w)x1850(h)x810(d) Technical data: - Fan power 3kW (ATEX) - Fan suction capacity: 16000 m³/h (max 1100Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan Ksdpfx Adjia Ta Hj Njwt - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: new, Year of construction: 2025, functionality: fully functional, working width: 250 mm, pass-through width: 250 mm, overall weight: 650 kg, The Ceetec A250 is a medium-sized unit from the series of coating machines and is therefore ideally suited for use in industrial and production facilities, such as paint shops, joineries, sawmills or building supply stores offering facade boards, decking, soffits, structural timber, etc. The device is most commonly used in manual mode, which means that the workpieces are loaded and unloaded by hand. Wooden components are conveyed horizontally through the machine by an automatic feed system. The Ceetec A250 ensures high-quality finishing thanks to its eight rotating brushes, each of which can be individually adjusted. Excess paint recirculates in a closed-loop system through a filter and back into the tank. The closed-loop circuit ensures optimal paint usage. The unit is supplied complete with brushes and a bag filter, making it ready for operation after connecting to a power source. The Ceetec A250 is a standard model, which means it is typically in stock and can usually be delivered at short notice. Brush coaters of the A-series are easy to keep clean. Consumable parts that naturally wear out are stocked in our warehouses, ensuring availability and fast delivery times. Thanks to the modular design of the machines, the operator can handle the replacement of most parts independently. The machine can be additionally equipped with a variety of brushes, bag filters with different mesh sizes, roller tables, and paint trolleys, among others. For processing raw wood, it is recommended to install a cleaning unit to remove dust and shavings before the machine. The device is intended for use with water-based products. ADVANTAGES OF CEETEC A250: Kwodpjxhc Tmjfx Ad Njt Independent adjustment of brush heads Application system using low-pressure nozzles and distributing brushes on all four sides of the workpiece Closed-circuit operation enabling recovery and reuse of excess preservatives Adjustable feed speed Can be equipped with a unit for handling short elements (from 800mm) Option to fit a 2m roller table at the machine infeed and outfeed Basic working parameters: Speed: from 18 m/min to 42 m/min Workpiece dimensions: Max. H: 250 mm x W: 250 mm. L: Min. 2000 mm. (other sizes available!) Power supply: 3 x 380 V + PE IP. Class 54 Machine dimensions: 2450 mm x 1200 mm x 2000 mm (height) Net weight: approx. 600 kg

Condition: new, Year of construction: 2024, ### 🔫 ProfiGun PM-1 powder gun Lightweight, ergonomic, perfectly balanced with a contoured grip. ✋⚖️ Adjust powder output and switch programs directly on the gun. 🎛️ Ceramic cascade up to 100,000 V for efficient charging of all powder types. ⚡ Kedpfx Ajflpi Nsd Nowt New-generation nozzles improve penetration on complex parts. 🎯🧩 Profiled nut for a secure grip + conductive handle for excellent operator grounding. 🔩🧤 Impact-resistant materials, fully demountable design, replaceable powder path tube. 🛡️🛠️ Patented in the EU and US. Polarity: negative. 🇪🇺🇺🇸➖ One-piece powder path + quick-release hose coupling reduce leaks and speed up hose changes. 🔌✅ ### 💨 ProfiJector powder pump Efficient injector with an optimized feed angle validated by research. 📐🔬 Lower powder and air consumption vs. right-angle injectors, with low running costs. ♻️📉 European patent protected. 🏅 ### 🖥️ PSS controller - 7" touchscreen 7-inch glove-friendly touch panel. 🧤📲 3 auto programs: overcoating, hard-to-reach areas, flat surfaces. 🔁 Fine tuning: 0.1 kV and 0.1 uA resolution. 🎚️ Advanced pneumatic valves for precise air dosing (patent pending) + real airflow measurement to detect drops or blockages. 💨📈⚠️ Diagnostics, program naming, external control via Modbus. 🧠🔧🔌 ### ⚡ ProfiCharge ceramic cascade (made in Poland) High-precision ceramic cascade up to 100,000 V, manufactured in Poland. 🇵🇱⚡ High-frequency ion emission (up to 17,000/sec) improves charging - less powder to the collector, more on the part. 🎯📉 Ultra-precise current control: 0-100 uA, stable even below 10 uA (0-10 uA focus with 0.1 uA steps). 🎛️ ### 💨 Air and application quality features Electronically controlled needle valves + integrated flowmeters for real-time, precise air delivery. 💨✅ Adjustable electrification curve for different powders and demanding parts. ⚙️🧩 Non-stick, puncture-resistant nozzles resist electrical breakdown, reduce clogging, and simplify color changes. 🧼✨ Automatic gun purge (from handle or screen) for faster, cleaner color changes. 🔁💨 ### 🛡️ Safety and compliance Discharge energy below 2 mJ + antistatic hose with double grounding strap. ⚠️🔒 ATEX and EN 50050-2 compliant for potentially explosive areas. ✅ ### 🧠 Productivity and support Quick Program: fast switching via rapid trigger presses. ⚡🎛️ Visual wear counters + fault history, suggestions, and self-monitoring diagnostics. 👀🔧 Up to 8 languages: PL, EN, DE, FR, RU, ES, IT, SV. 🌍 Animated troubleshooter for guided diagnostics. 🧭 Professional mode (hints on/off) + daily and job statistics for order management. 📊⏱️✅

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 3,500 mm, total length: 7,050 mm, total width: 4,100 mm, volume flow: 36,000 m³/h, temperature: 80 °C, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), Equipment: cabin, lighting, Paint and Drying Booth It is the centerpiece of your entire painting operation: the combined paint and drying booth. (Alternatively available as a separate paint booth with a dedicated dryer.) Our solutions feature full-surface ceiling filters and, optionally, full-surface floor extraction with drive-over grating or wall extraction at the position of your choice. If you wish to further increase the efficiency of the system beyond heat recovery and infinitely variable control via frequency converter, we can also offer you a sectional control system. This enables you, for example when doing spot repairs or partial booth loading (such as painting only add-on parts), to activate only the section where the parts are located. This allows you to operate with a reduced air volume, save energy, and minimize costs, all without compromising quality. Feel free to contact us – we would be happy to demonstrate these options in detail. Do you have any questions or suggestions? Kedpsxa H Ewsfx Ad Njwt We are happy to assist you.

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS Kwsdpfjwzmcbox Ad Not During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. Kjdpfewzl Hxox Ad Nswt * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, Year of construction: 2024, functionality: fully functional, - FAGOR 3-axis position indicator, Mod.: 400iB INNOVA - Milling head +- 90° manually swiveling - Manual tool clamping using M 16 tightening screw for vertical and horizontal spindle - Swiveling control panel - Motor for horizontal and vertical spindle - Feed motors with inverter for X/Y/Z axis - Ball screw spindles in the X/Y/Z axes - Gearbox for 12 spindle speeds - Counterholder with support bearing - 1 long milling mandrel 27 mm - 3 reducing sleeves (MK1, MK2, MK3) - Spindle protection with safety switch Ksdpfxovt Tn As Ad Newt - Splash protection on the 3 sides of the horizontal table - LED work light - Automatic lubrication for X/Y/Z guides - Mechanical handwheels for X/Y/Z axes - Coolant system - Cover for X/Z axes - Operating tool - Technical Documentation - CE version Colors: - RAL 7024 – graphite gray - RAL 7035 – light gray Technical data: Fixed angle table: - Dimensions of the work surface: 845 x 390 mm - T-slots: number / width x distance: 5 pcs. / 14 x 63 mm - Max. table load: 250 kg Vertical table: - Dimensions of the work surface: 950 x 250 mm - T-slots: number / width x distance: 3 pcs. / 14 x 63 mm Travel paths: - Axis travel paths: automatic/manual - Longitudinal (X): 420 mm - Transverse (Y): 220 mm - Vertical (Z): 380 mm Vertical milling head: - Tool holder: ISO 40 / DIN 2080 - Speed range: 65 - 2,600 rpm. - Number of spindle speeds: 12 (65 – 100 – 130 – 175 – 260 – 357 – 485 - 690 – 950 – 1,325 – 1,870 – 2,600) - Quill stroke, manual: 100 mm - Head swivel: +- 90° - Distance spindle nose/table: 90 - 470 mm - Distance spindle center to column - min./max.: 120 - 340 mm Horizontal spindle: - Tool holder: ISO 40 / DIN 2080 - Gear stages: 12 - Speed range: 65 - 2,600 rpm. - Distance spindle center / table: 100 - 480 mm Feeds: - Control: stepless - Range (X,Y,Z): 0 - 1,000 mm/min. - Rapid traverse (X,Y,Z axes): 1,000 mm/min. Motors: - Main drive power: 2.2 kW - Feed motor power (X-Y-Z): 0.35 kW - Coolant pump: 0.09 kW Dimensions and weight - Dimensions (W x D x H): 1,621 x 1,527 x 1,938 mm - Weight: 1,300 kg

Condition: new, Year of construction: 2024, - FAGOR 3-axis position indicator, Mod.: 400iB INNOVA - Milling head +- 90° manually swiveling - Manual tool clamping using M 16 tightening screw for vertical and horizontal spindle - Swiveling control panel - Motor for horizontal and vertical spindle - Feed motors with inverter for X/Y/Z axis - Ball screw spindles in the X/Y/Z axes - Gearbox for 18 spindle speeds - Counterholder with support bearing - 1 long milling mandrel 27 mm - 3 reducing sleeves (MK1, MK2, MK3) - Spindle protection with safety switch - Splash protection on the 3 sides of the horizontal table - LED work light - Automatic lubrication for X/Y/Z guides - Mechanical handwheels for X/Y/Z axes - Coolant system - Cover for X/Z axes - Operating tool - Technical Documentation - CE version Colors: - RAL 7024 – graphite gray - RAL 7035 – light gray Technical data: Fixed angle table: - Dimensions of the work surface: 1,000 x 540 mm Kedovunrfopfx Ad Nowt - T-slots: Number / width x distance: 8 pcs. / 14 x 63 mm - Max. table load: 300 kg Vertical table: - Dimensions of the work surface: 1,200 x 250 mm - T-slots: Number / width x distance: 8 pcs. / 14 x 63 mm Travel paths: - Axis travel paths: automatic/manual - Longitudinal (X): 600 mm - Transverse (Y): 500 mm - Vertical (Z): 400 mm Vertical milling head: - Tool holder: ISO 40 / DIN 2080 - Speed range: 40 - 3,200 rpm. - Number of spindle speeds: 18 (40 - 65 – 83 – 100 - 130 – 160 – 200 – 250 - 400 - 330 520 – 650 – 820 – 1,020 – 1,280 – 1,600 – 2,000 – 3,200) - Quill stroke, manual: 100 mm - Head swivel: +- 90° - Distance spindle nose/table: 70 - 470 mm - Distance spindle center to column - min./max.: 160 / 660 mm Horizontal spindle: - Tool holder: ISO 40 / DIN 2080 - Gear stages: 18 - Speed range: 40 - 3,200 rpm. - Distance from spindle center / to 2nd T-slot: 95 - 495 mm - Distance from spindle center / to 3rd T-slot: 180 - 580 mm Feeds: - Control: stepless - Range (X,Y,Z): 0 - 600 mm/min. - Rapid traverse (X,Y,Z axes): 600 mm/min. Motors: - Main drive power: 3.75 kW - Feed motor power (X-Y-Z): 0.35 kW - Coolant pump: 0.09 kW Dimensions and weight - Dimensions (W x D x H): 1,881 x 1,813 x 1,916 mm - Weight: 1,600 kg

Condition: good (used), Year of construction: 2001, Heidenhain TNC 310 cnc control electronical hand wheel coolant device Technische Daten: Längsweg (X-Achse) / X-travel longitudinal 600 mm Querweg (Y-Achse) / Y-travel cross 400 mm Senkrechtweg (Z-Achse) / Z-travel vertical 400 mm Werkzeugaufnahme / spindle taper SK 40 Drehzahlbereich / spindle speed range 60-5000 UpM Vorschub / feed 0-2000 mm/min. Eilgang längs + quer / rapid feed x/y 5 m/min. Eilgang senkrecht / rapid feed z 4 m/min. Antriebsleistung gesamt / drice capacity 7 kW Kwsdpfsit Tr Tsx Ad Not Gewicht ca. / weight ca. 2000 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: good (used), Year of construction: 1997, functionality: fully functional, feed length X-axis: 450 mm, feed length Y-axis: 300 mm, feed length Z-axis: 350 mm, 3-axes digital read out horizontal and vertical milling spindle quill Technische Daten / technical details: Längsweg X / X-travel longitudinal 450 mm Kwedpfx Aswyit Hsd Not Querweg Y / Y-travel cross 300 mm Senkrechtweg Z / Z-travel vertical 350 mm Tischgröße / table size 800x400 mm Spindelaufnahme / spindle taper SK40 Drehzahlbereich / spindle speed 50-2500 UpM /rpm Vorschubbereich / feed range 8-400 mm/min. Antriebsleistung / power capacity 3,2 kW Gewicht der Maschine / weight 1500 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Year of construction: 2025, condition: new, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ Kwodpfxofz I Rxs Ad Njt At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, Paint/spray wall dimensions without fan and control Panel! Extraction surface - dimensions (mm): 3000(w)x1900(h) Overall dimension(mm): 3100(w)x2350(h)x810(d) Technical data: Kjdeia Ta Ropfx Ad Newt - Fan power 3kW (ATEX) - Fan suction capacity: 16000 m³/h (max 1100Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty We can manufacture filtration supply (new air to sprayroom). Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, Paint/spray booth dimensions without fan and control Panel! Suction area - dimensions (mm): 2190w)x2350(h) Kedpfx Aoia Taqsd Nswt Overall dimension (mm): 2295(w)x2295(h)x1910(d) Technical data: - Fan power 2.2 kW (ATEX) - Fan suction power: 12000 m³/h (max. 1100Pa) - Lighting: 1pc 2x58W (ATEX) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us.

Condition: new, Year of construction: 2026, functionality: fully functional, type of input current: three-phase, warranty duration: 12 months, Paint/spray wall dimensions without fan and control Panel! Extraction surface - dimensions (mm): 4430(w)x1900(h) Overall dimension(mm): 4530(w)x2350(h)x810(d) Technical data: Kodpsia Ta Uofx Ad Nswt - Fan power 4.4kW (ATEX) - Fan suction capacity: 24000 m³/h (max 1200Pa) - Connection voltage: 400V - Frequency converter for smooth regulation of the fan - Three-stage air filtration - Intended for explosive environments - EX - Complete technical documentation - CE Documentation - Warranty Possibility to order machines in various individual configurations and dimensions! Do not hesitate to contact us