Used Nuclear Power Oil-Press for sale (47,604)

Condition: as good as new (ex-display), Year of construction: 2022, pressing force: 400 t, Press design double column press Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 4000 kN Free ripping force max. 400 kN Pressure build-up time Closed die steel to steel Max. 4 sec. Dimensions 3,800 mm long and 4,475 mm wide Max. Opening width 800 mm Stroke 800 mm Table height above floor 1100 mm Height above floor (headroom) approx. 4300 mm Hall height min. 5500 mm parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of press without operating materials and table plate approx. 28 t Press table Table size 1500x1500 mm Speeds Fast closing with 100 mm sec. Pressing speed 8 - 3 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of pressing cylinders/driving cylinders 1 pc. Operating pressure max. 300 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 3 bar Main pump BOSCHREXROTH axial piston pump approx. 145 L/min Oil volume approx. HLP 46 MW 1000 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Auxiliary pump BOSCHREXROTH, gear pump 10 L/min Pressure stabilization for up to 300 sec. Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Connection hydraulics main motor 40 kW Sliding table press with 400 T capacity, Closing speed up to 100 mm/ ( adjustable via touch screen ) Opening speed up to 100 mm/sec ( adjustable via touch screen ) Starting press speed 10 mm/sec ( adjustable via touch screen ) table top size 1500x1500mm ram size approx. 1600x1500mm Oil temperature monitoring 55 degree warning, 60 degree shutdown Automatic lubrication ( adjustable via touch screen ) Free positioning of the ram ( adjustable via touch screen ) SICK/PILZ light barriers 14 mm, front, up to 1800 mm height Redeph Uk Njpfx Acdscb Hydraulic and mechanical ram protection Circuit oil cooling ( adjustable via touch screen ) Ejector in table, 20 T press force, 350mm travel Ejector moves outwards with the table Table plate milled flat, with DIN 22 T grooves Pressure adjustment from 60 T to 400 T ( adjustable via touch screen ) Travel limitation either by pressure or position Set-up mode, single stroke and cycle sequence ( adjustable via touch screen ) Swiveling control panel on the cabinet Two-hand operation, with opening button, manual/single stroke/cycle switchover button Installation, commissioning, instruction against separate charge The control is supplied by SIEMENS. ( S 7 1200 ) Also the touch screen monitor with 9 inch. The remote maintenance unit SECOMEA -Ethernet is included in the delivery. The side of the press has two 1000 mm high and 800 mm wide windows with double doors. (sliding table press, hydraulic press, hydraulic press, double column press)

Condition: new, Year of construction: 2022, pressing force: 15 t, Single column press with 15 T capacity suitable for continuous shift operation a) travel speed 10 mm/sec. downwards, b) opening speed up to 25 mm/sec c) starting pressing speed 10 mm/sec d) table size 400x400 mm e) ram size 200x200 mm, with T grooves and central cylinder clamping Rcjdsitylgjpfx Acdeb f) Overall size approx. 1150x800x1750 mm g) oil temperature display on oil tank h) pressure adjustment from 5 T to 17 T ( adjustable by rotary control ) i) Hand lever operation with two speeds j) Machine body powder-coated, or double-painted k) Control cabinet supply line from above with 3000 mm cable and 16 Ampere plug l) assembly, commissioning, instruction against separate calculation Press design Single column press Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Press force max. ( at 250 bar ) 150 kN Free ripping force max. 10 kN Pressure build-up time Closed die Steel to steel Max. 2 sec. Max. Opening width 400 mm Stroke and min. opening 350 mm Table height above floor 850 mm Height above floor (headroom) approx. 1900 mm Hall height min. 2.500 mm Parallel deviation at 20°C +/- 0.1 mm Determined at max. clamping force with 70% occupancy < = 0.3 mm/m Weight Total weight of the press without operating materials approx. 1.1 to Fast closing with 10 mm sec. Press speed 10 - 0 mm sec. Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 290 bar Pressing pressure build-up time . 2 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump Gear pump approx. 9 L/min Oil volume approx. HLP 46 MW 80 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Electrical system 400 V AC Main supply Control voltage 24 V DC Hydraulic pumps 24 V DC Frequency 50 Hz Hydraulic connection Main motor 3 kW Total connection Approx. 5 kW Equipment control cabinet Protection class IP 54 Reserve space Approx. 20 Cooling no Interior lighting no Operating mode switch Lockable yes

Condition: used, Pneumohydraulic cylinder TOX Pressotechnik Hydro-pneumatic press, power pack Type: S 04.00.050.12 D No.: 208696.460 Year of manufacture approx. 2000 Pressure capacity: 4.0 tons at 10 bar Pressure capacity: 3.0 tons at 8 bar Pressure capacity: 2.6 tons at 7 bar Pressure capacity: 2.4 tons at 6 bar Pressure capacity: 2.0 ton. at 5 bar Pressure capacity: 1.6 ton. at 4 bar Pressure capacity: 1.2 tons at 3 bar Total stroke: 50 mm Power stroke: 12 mm Piston rod: Ø 30 mm Thread for piston rod: M22 x 2 mm Rcsdpfx Asu D Tz Uocdsb Compressed air requirement: 3 to 10 bar - Electronic oil pressure switch with TOX digital display for force measurement, type 167282 - Height only power pack with piston rod = 610 mm - Height of power pack hydropneumatic cylinder only = 560 mm - Additional base plate 160 x 160 x 20 mm - Plunger plate: Ø 68 mm Space requirement L x W x H: 160 x 160 x 660 mm Weight: 21 kg Very good condition 3 pieces available, price per piece

Condition: used, Press machine, REMS Power-Press XL ACC, used equipment Manufacturer: Rems Rsdpfxsxlp T Ie Acdocb Type: Power-Press XL ACC Pressing range: Ø 10 – 108 mm (up to 110 mm) Pressing force: 32 kN Motor: 450 W universal motor Power supply: 230 V or 110 V, 50–60 Hz Weight: approx. 5.5 kg Dimensions (H x W x D): 800 x 335 x 230 mm Cable length: 2900 mm Accessories: more than 400 types of REMS pressing jaws, adapters for other manufacturers Additional features: Automatic retraction (Automatic Circuit Control – ACC) Rotatable pressing jaw holder with automatic lock Compatible with pressing jaws from other manufacturers Fast pressing, e.g., Geberit Mapress stainless steel Ø 108 mm connection in 15 seconds Press jaws: 76.1; 88.9; 108 mm

Condition: good (used), TABLE PRESS WITH POWER UNIT Rodpfx Ajk Adfnocdscb

Condition: good (used), Code: 0283 Brand: ITALPRESSE Model: 25/13 Fabricated platen for diathermic oil press Technical data: Platen dimensions: mm 2500 x 1300 Rcsdpfxoyazdis Acdsb Max temperature up to 120° Max working pressure: 3/5 kg/cm2 Heating medium pressure 0,5 ate Composition: Aluminium - Flat gauged steel sheet - Coil of piping for fluid circulation - Reinforcement piping - Flat gauged steel sheet - Insulating material

Condition: good (used), Riello oil burner 482M1,power 2370Kw,220kg/h Rcedpfx Aepir Ryscdjb

Condition: new, Year of construction: 2022, OMC 3000×1300 105T Oil Shelf Press Working surface 3000x1300mm Opening width 400mm 6 cylinders with a diameter of 85mm Total pressure 105T Maximum heating temperature of 85 degrees Control system logic contorl Machine control from touch panel readouts Temperature, pressure force, shelf opening time, loading area calculator, glue process programming Power 21KW Rcjdpfxoimwp Sj Acdjb CE certificate Production 2022 Machine available on request New machine

Condition: used, Hydraulic Power Unit ACME TYPE ZPR 6 Ref. No.: 962116 Year of manufacture: approx. 1972 Operating pressure: max 40 bar Flow rate: 10 litres/min. Tank capacity: 15 litres - In-line filter Motor power: 0.37 kW Rcodexf Uz Depfx Acdeb Power supply: 380 Volt, 50 Hz Installation dimensions (L x W x H): 500 x 270 x 500 mm Net weight: approx. 80 kg Test run with pressure test

Condition: excellent (used), Weishaupt dual fuel burner RGL70,oil+gas,power 10500kw Rcjdpopir Unsfx Acdsb

Condition: used, mileage: 167,307 km, power: 257 kW (349.42 HP), first registration: 07/2006, fuel type: diesel, empty load weight: 15,850 kg, maximum load weight: 10,150 kg, overall weight: 26,000 kg, tire size: 315 / 80 R 22,5, axle configuration: 6x2, wheelbase: 4,200 mm, brakes: constant throttle, color: orange, driver cabin: day cab, gearing type: automatic, emission class: euro4, suspension: steel-air, number of seats: 2, total length: 2,500 mm, total width: 3,550 mm, Equipment: ABS, air conditioning, cabin, cruise control, differential lock, fog lights, low noise, Vehicle location: Bovenden, license plate house, 1x air seat, electric mirrors, heated mirrors, electric window left, electric window right, air conditioning, radio, cruise control, ABS (anti-lock braking system), constant throttle, raised exhaust, automatic, lifting+lowering, central lubrication system, differential lock, fog lights, rotating beacon, leaf-air suspension, low-noise G1, last axle forced steering, environmental badge green Wheelbase: 4200 mm Body: FAUN POWER PRESS 524 , WAAGE SYWATEC scales Sywatec weighing range 200kg-12000kg, reversing camera Vehicle is without engine!!! ACCESSORIES WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! Redpfovhhgvsx Acdecb - .

Condition: used, Year of construction: 2006, operating hours: 14,000 h, functionality: fully functional, machine/vehicle number: 85-089, overall weight: 20,000 kg, RAPESEED OIL PRESS SYSTEM A complete and automatic rapeseed oil press installation based on a Reinartz AP15 press with a 55Kw motor driven via a DANFOSS VLT 5062 frequency controller and has a capacity of 1000 Kg rapeseed - 800 Kg sunflower seeds per hour, a crude oil stirring tank of 15,000 liters with a Wangen KL30S60.00 eccentric pump as feed to an automatic AMA filter system consisting of a plate filter with 20 m2 filter surface and 2 fine filters, one with filter bag and one with filter candles up to 0.5 micron size of the impurities. The seed supply is done via a dosing screw with the possibility of heating the seed, the real entrance to the press is protected by a permanent magnet to catch iron impurities. The discharge of the rapeseed cake is done via a chain conveyor and conveyor belt. The entire installation is controlled via a SIEMENS Simatic Multi Panel touch screen control cabinet of approximately 1m wide / 2m high. This cabinet also contains a modem to forward error messages to various GSMs. The control can work in auto mode as well as in manual mode. In addition to these most important systems, the installation also contains the necessary additional silos for filling the main silo, which enables 24/7 operation. Rcedswl Afyjpfx Acdob The entire installation was built in 2006 and has produced 14,000 hours and is now completely ready for transport. If desired, the sale of individual elements can be discussed. If further information is required, this can best be done by email and preferably in Dutch, French or English.

Condition: used, mileage: 175,000 km, power: 210 kW (285.52 HP), first registration: 12/2010, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, color: white, gearing type: automatic, emission class: euro5, total width: 2,550 mm, total height: 3,520 mm, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, * Mercedes Benz 2629 ECONIC refuse collection vehicle with Faun Power Press 522 and Zoeller lifter - Euro 5 - * Diesel - Engine capacity: 6,374 cc - 210 kW / 290 hp - Euro 5 - Green environmental badge - * German vehicle - German registration certificate - Immediately available - From first owner - Rcsdpfx Aox A Rbuocdeb * Unladen weight: 16,050 kg - Permissible total weight: 26,000 kg - Payload: 9,950 kg * Tyres: 315 / 60 R 22.5 - Vehicle is immediately available and ready for collection - * Please schedule an appointment for viewing - * Contact: Mr. Andreas Vogel * The information provided on the internet is non-binding and for description purposes only. * They do not constitute guaranteed characteristics. * The seller does not accept liability for typographical or data transmission errors. * Subject to change, error, and prior sale.

Condition: ready for operation (used), Year of construction: 2007, punching force: 31 t, total height: 2,200 mm, total width: 5,165 mm, travel distance X-axis: 2,500 mm, travel distance Y-axis: 1,250 mm, overall weight: 12,000 kg, controller manufacturer: SIEMENS, controller model: SINUMERIK 840D CNC, product length (max.): 5,570 mm, number of axes: 2, This 3s Finn-Power C5 + Compact Express CNC punching machine was manufactured in 2007. It features a working area of 2500 × 1250 mm and a punching force of 30 tonnes. With 20 tool stations and a maximum tool diameter of ~89 mm, it offers efficient operation. Consider the opportunity to buy this Finn-Power C5 + Compact Express CNC punching machine. Contact us for further details. Redpfjyiz Igox Acdocb • Maximum sheet thickness (steel): 8 mm • Number of tool stations: 20 • Maximum tool diameter: ~89 mm • Table clamps: 3 (typically pneumatic) • Sheet weight capacity: ~200 kg • Traverse speeds: X ~90 m/min; Y ~60 m/min • Table support: vacuum or brush table Additional equipment • Automatic loading/unloading system (automatic material handling, loaders/unloaders) • Chip/slug conveyor belt

Condition: used, Oil-water separator KAESER BEKO, type Öwamat Tank diameter: 600 mm Rodpfx Acsy Ty Saodecb Overall height: 1200 mm With activated carbon filter Space requirement: Ø 700 x 1200 mm Weight: approx. 30 kg In good condition.

Condition: used, operating hours: 32,574 h, Ingersoll Rand SSR MH-55 Rotary Screw Air Compressor – Used Industrial Compressor Description: Ingersoll Rand SSR MH-55 industrial rotary screw air compressor, suitable for workshop, manufacturing, fabrication or general factory compressed-air supply. This is a heavy-duty industrial compressor with integrated control panel, air pressure and temperature gauges, hour meter, electrical cabinet and internal compressor/motor assembly. The machine is currently in used condition and has been removed from regular service / stored on site. The hour meter show approximately 32,574 hours. Key features: Manufacturer: Ingersoll Rand Model: SSR MH-55 Type: Rotary screw air compressor Integrated control panel Air pressure gauge Temperature gauge Hour meter fitted Internal compressor and drive motor present Industrial cabinet-mounted unit Suitable for production or workshop air supply Good candidate for recommissioning, refurbishment, spares or export Condition: It is offered sold as seen. Buyer should inspect the compressor and satisfy themselves as to running condition, electrical requirements, service history, capacity, pressure rating and suitability before purchase. Important note: Professional inspection, lifting, loading, transport and recommissioning will be the buyer’s responsibility unless otherwise agreed. Electrical and pressure-system checks should be carried out before use. Ideal for: Engineering workshops Manufacturing sites Rsdpfx Aey Ry E Uocdecb Fabrication shops Spray shops Industrial air systems Compressor refurbishment specialists Spares or parts use Viewing recommended. Loading / removal: Buyer to arrange, unless agreed separately

Year of construction: 2019, condition: excellent (used), functionality: fully functional, Farmet FL200 screw press for rapeseed/sunflower/soybean, with final geometry, in a really good condition. Rcedjxa Hy Uopfx Acdob Motor 22kw, capacity 400kg/h (with prepress 500kg/h), lamels and geometry checked, and in a good shape. Paired with extruder Farmet FE500 (from our offer) it can process soybean at 400kg/h

Year of construction: 2006, condition: good (used), Oilseed screw press Farmet FS1000, 55kw long. In a good condition, complete, ready for loading. Capacity up to 1.400kg/h. Rjdexrc Ixopfx Acdocb

Year of construction: 2006, condition: good (used), functionality: fully functional, Screw press Farmet FS1000 for rapeseed, soybean, sunflower. Capacity from 800kg to 1.000kg, depending on motor. It is complete, in good condition. Manufactured in 2006 Rcedpfxstxc Its Acdsb

Condition: ready for operation (used), Year of construction: 2002, Extruders and oil screw presses for soybean processing, obtaining oil and soybean cake. There are two extruders and two presses. One extruder and one press work in tandem and form a pressing line. The motor power of the press is 22 kW and the power of the extruder is 55 kW. the capacity of one line is 500-800kg/h Rcodpfjtxinajx Acdeb The price refers to one line (exstruder+press)

Condition: excellent (used), machine/vehicle number: 46131, Stamping surface with heating head: HKAC max. 100 x 125 mm // HKBC max. 140 x 230 mm Stamping pressure at 6,5 bar with: 1 Zylinder ca 400 daN (kp) // 2 Zylinder ca 800 daN (kp) Readjustable stroke, dep. on pressure producer: 0-40 mm / 0-100 mm Max. passage height without/with sliding table: 300 mm / 275 mm Readjustable foil advance: 0-230 mm Max. foil width: 140 mm Heating voltage: 220 V / 50 Hz Heating capacity with heating head: HKAC 540 W // HKBC 900 W Temperature measurement by means of: Fe-Ko Redpfx Aex I Nfrecdjcb Max. output, hourly cycles: ca 4000

Condition: good (used), Year of construction: 2015, Atlas Copco Oil Free Screw Compressor with built-in Air Dryer Model SF2+FF 7.75 bar / 112 PSI Year 2015 Redpfx Asy Iplfecdocb 400 volts three phase, 2.2 KW / 3 HP, 2885 RPM 8.9 CFM / 4.21 lts/s Very little use Ex Pharma Facility

Condition: used, Year of construction: 2007, operating hours: 2,568 h, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, overall weight: 4,900 kg, pressure: 200 bar, electrical fuse: 27 A, We offer this used LUX VM-TEC K50V4 baler for paper, foil, and plastics, year of manufacture 2007. The baler comes complete with conveyor. Rcodpfey H E R Isx Acdjb Model: K50V4 Year of manufacture: 2/2007 Production number: abba359 Serial number: Cont-000089 Power: 18.5 kW Current: 27 A Voltage: 400 V Frequency: 50 Hz Maximum pressure: 200 bar Weight: 4,900 kg If you have any questions or require further information, please feel free to send us a message or contact us by phone.

Condition: used, This listing is for the Bambi VTS 150D Oil Free Dry Air Rcedpfxjy H Dv Ae Acdjb The unit is in full working condition and ready for immediate use. Compact and ultra-quiet, this oil-free compressor delivers clean, dry air for sensitive laboratory applications, including analytical instruments and medical devices. Built for reliability and low maintenance operation. Transparency Report and Technical Audit: • Source Pedigree: Biotech / Research Facility • Condition: Direct-from-Bench (Decontaminated/Original) • Power-On Test: Verified; Digital display active, lighting operational, and fan system engaged. • Integrity: 100% Original Parts (Non-Refurbished) Notice for Procurement: This unit is sold As-Is. While we verify the power-on status and physical integrity, we do not perform analytical validation, fluidic testing, or operational calibration. Ideal for labs with in-house technical expertise or existing service agreements. Sustainability Impact: By choosing Direct Reuse, your facility avoids the carbon footprint of new manufacturing and prevents specialized materials from entering waste streams. Direct-to-Lab reuse is the most carbon-efficient way to equip a modern laboratory • Source Pedigree: Biotech / Research Facility • Condition: Direct-from-Bench (Decontaminated/Original) • Integrity: 100% Original Parts (Non-Refurbished)

Condition: excellent (used), Year of construction: 2002, operating hours: 46,357 h, functionality: fully functional, Oil-free screw compressor Atlas Copco GA75VSDFF Redpfxjyz R U Is Acdjcb Inverter and dryer integrated. 160 kW 7.5 bar 27.90 m3/min Year of manufacture: 2002 Operating hours: 46,357