Used Indexers for sale (1,230)

Condition: used, Year of construction: 2017, functionality: fully functional, X-axis (planar travel): 195 mm (approx. 7.67 inches) Z-axis (longitudinal travel): 400–430 mm Tailstock travel / quill travel: 100 mm (quill stroke) Rapid traverse X-axis: 30 m/min Rapid traverse Z-axis: 30 m/min C-axis (spindle indexing): 0.001° (for driven tools / MC version) Center height: 1,000 mm Max. spindle speed: 3,500 rpm Max. chuck diameter: 10 inches Djdpfx Aoz Hwaijl Ajku Max. chuck speed: 4,200 rpm Max. working area (diameter x length): Ø 325 mm x 302 mm Machine weight: 4,350 kg Operating voltage: 3 PE / 220 V (AC) Rated frequency: 50 Hz Electrical connections / power: 30 kVA Rated current: 100 A Short-circuit current strength: 5 kA Largest motor: 80 A Circuit breaker capacity: 100 A Switching capacity of protective device: 50 kA Compressed air supply: 0.5 MPa (5 bar)

Condition: used, Year of construction: 2018, machine/vehicle number: 10619-1, MEYPACK VP 451 tray and wrap-around packaging machine Fully automatic machine for packing beverage cans into trays and wrap-around cartons. Products and formats: - 0.33-litre cans, Ø 66 x 115 mm, loose and in four-packs - 0.5-litre cans, Ø 66 x 168 mm, loose and in four-packs Pack configurations for both can formats: - 4 x 6 loose cans in a wrap-around carton or tray - 3 x 4 loose cans in a wrap-around carton - 2 x 3 four-packs in a tray Output: - Nominal output: 16,000 cans/h - Packaging output: 12 or 24 packs/min, including a 5% capacity reserve Product handling: - Multi-lane bulk product infeed - Four-packs fed transversely on two lanes, with the openings facing sideways - Infeed height: approx. 1,150 mm ± 50 mm - Outfeed height: approx. 650 mm ± 50 mm - Trays and wrap-around cartons leave the machine broad side leading Operating principle: The products are fed continuously in multiple rows, distributed evenly into the lanes of the infeed conveyor using the accumulation principle, and grouped into the required formation. At the same time, a flat tray or wrap-around blank is removed from the magazine and positioned below the grouping station. The servo-driven lowering station receives the product formation and blank and folds the blank tightly around the products. A servo-driven indexing chain then conveys the pre-folded pack through the gluing and compression stations. The finished pack is transferred to the downstream conveyor system via a gravity roller conveyor. Grouped-pack size range: - Length: 200–400 mm - Width: 120–300 mm - Height: 80–200 mm - Tray height: 40–200 mm Packaging material and magazine: - Suitable for almost all commercially available corrugated-board grades; final design subject to approval by MEYPACK - Blank length: 360–1,250 mm - Blank width: 300–700 mm - Magazine capacity: approx. 150 blanks or approx. 400 mm stack height for B-flute board - Flat blanks are separated by vacuum cups and positioned by a belt conveyor - Hot-melt adhesive: commercially available grades approved by the adhesive-unit manufacturer; final design subject to approval by MEYPACK Utilities: - Electrical supply: 3 x 400 V AC, 50 Hz, with neutral and protective conductor; permissible long-term voltage fluctuation ± 5% - Control voltage: 24 V DC - Compressed air: 6 bar, 1/2-inch connection; clean and free from foreign matter, gases and oils Operation and format change: - The machine can be monitored by one operator while performing another task - Operator side can be arranged on the right or left when viewed in the outfeed direction - Fast, repeatable format changes through zero-line design and automatic indexing-chain adjustment - Settings documented in product-specific format lists; clearly assigned and marked change parts Basic machine and components: - Weight: approx. 3,500 kg - Finish: black grey RAL 7021 - Pneumatics: Festo - Hot-melt unit: Nordson Pro Blue - Drives: SEW, protection class IP55 - Control system: Siemens S7 - Operator interface: Siemens Touch Panel TP 1500 - Electrical design in accordance with MEYPACK standard electrical equipment specification E 2017 Included options: - Additional tray takeaway conveyor for manual palletising - Painted-steel roller conveyor with integrated corner transfer, nominal width 350 mm, length approx. 1,100 mm - Two-lane transfer unit with modular belt chain, adjustable side guides on one side and stainless-steel cable duct - Broadband VPN router for remote machine maintenance - Swivel arm for Dkodjz Icmkspfx Al Aeu

Condition: ready for operation (used), Year of construction: 2020, travel distance X-axis: 350 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 510 mm, controller manufacturer: MAZATROL, controller model: SmoothG, total height: 2,840 mm, total width: 1,900 mm, overall weight: 7,100 kg, spindle speed (max.): 18,000 rpm, number of slots in tool magazine: 30, tool weight: 8,000 g, product length (max.): 3,060 mm, number of axes: 5, This 5-axis Mazak VARIAXIS J-500/5X was manufactured in 2020. It features a maximum spindle speed of 18,000 rpm and a rapid traverse rate of 30,000 mm/min. The machine includes a tool magazine capacity of 30 tools and a robust table size of 500 x 400 mm. If you are looking to get high-quality machining capabilities, consider the Mazak VARIAXIS J-500/5X vertical machining centre we have for sale. Contact us for further details. • CNC control: MAZATROL SmoothX with 19-inch colour touchscreenWorking capacity and travels • A-axis tilt: -120° to +30° • C-axis rotation: ±360° • A/C indexing increment: 0.0001° • Rapid traverse X/Y/Z: 30,000 mm/min • Max cutting feed X/Y/Z: 30,000 mm/min • A-axis index time: 0.6 s per 90° • C-axis index time: 0.55 s per 90° / 1.05 s per 180°Table and clearances • Tilting/rotary table (A/C axes) • Table size: 500 × 400 mm • Table with T-slots (as per final configuration) • Spindle nose to table surface (table horizontal): 50–560 mm • Spindle nose to table centre (table vertical): 40–550 mmSpindle • Spindle chiller with 16 L cooling oil tank • Programmable spindle orientation in 1° incrementsTool magazine and ATC • ATC with recovery function; digital magazine display and external operating panel • Tool selection: fixed addresses with automatic shortest-path selection • Pull stud: Yamazaki ANSI • Max tool length: 300 mm • Max tool diameter with adjacent tools: 90 mm • Max tool diameter with adjacent pockets empty: 130 mm • Chip-to-chip time: 6.20 sMeasuring and probing • Renishaw RMP600 radio workpiece probe • MAZA-CHECK system • Automatic tool length measurement and tool breakage detection • G37 automatic tool length measurement • Absolute positioning systemCoolant and chip management • Through-tool high-pressure coolant: approx. 15 kgf/cm² (≈14.7 bar), approx. 35 L/min • Coolant tank: 300 L • Coolant washdown system and manual washdown gun • Cooling for X/Y/Z ball screws • Workpiece air blastControl and software • MAZATROL SmoothX CNC • EIA/ISO programming package • Simultaneous 5-axis control • Additional 5-axis machining package for SmoothX • 3D coordinate rotation • Smooth synchronous tapping • G00 Slope Constant (rapid optimization) • Smooth restart • Tilted machining plane • Inverse Time Feed • Extended work offsets: 300 pairs • Variable macros: 600 variables • High-speed machining and smoothing • Geometric compensation for rotary axes • Interfaces: USB, LAN, SD cardConstruction, safety, and other features • Electronic handwheel • Three-colour signal tower • Automatic machine power on/off and warm-up • Roller linear guideways • Full enclosure with top cover; interlocked operator door • Work area lighting • Intelligent Safety Shield (ISS) • CE marking Additional equipment • CROWTHER right-side hinged-belt chip conveyor (for steel machining) • GX500 mist extraction unit with extraction preparation • European-market power transformer • Machine installation kit • Polish manuals and safety labels Dkjdpfx Ajz Iqgrsl Aju Technical Specification Taper Size SK 40 Through-spindle Coolant Yes

Condition: used, Year of construction: 2010, turning length: 1,495 mm, spindle speed (min.): 35 rpm, spindle speed (max.): 5,000 rpm, spindle bore: 65 mm, travel distance X-axis: 580 mm, travel distance Y-axis: 160 mm, travel distance Z-axis: 1,545 mm, workpiece weight (max.): 300 kg, total height: 2,577 mm, total length: 5,088 mm, total width: 2,450 mm, spindle nose: A2-6, spindle diameter: 660 mm, Equipment: documentation/manual, CNC Control Mazatrol Matrix Turning diameter 660 / 260 mm Turning length 1495 mm Spindle bore diameter 65 mm Spindle nose A2-6 Spindle nose sub spindle A2-6 Turning speed spindle 35 - 5.000 R/min Turning speed sub spindle 35 - 5.500 R/min Milling head speed 15 - 12.000 R/min Djdpfozqt Umsx Al Ajku Movement X-axis 580 mm Movement Y-axis 160 mm Movement Z-axis 1.545 mm B-axis travel 225° C-axis indexing 0,0001 (360) ° Tool taper Capto C6 Tools in tool magazine 120 Barfeeder Irco-Breuning ILS-MUK If you have any questions concerning the machine, please do not hesitate to contact us by phone or e-mail. Feel free to view our other advertisements for a complete overview of our stock.

Condition: ready for operation (used), functionality: fully functional, spindle speed (max.): 5,000 rpm, controller model: INDEX C200-4, TECHNICAL DETAILS Main Spindle Spindle bore with collet clamping: 65 mm Dodsz Im Uropfx Al Aeku Spindle diameter in the front bearing: 100 mm Speed: max. 5,000 rpm Spindle nose according to ISO 702/1: Size 5 Torque at 100%: max. 62/95 Nm Power at 100%: max. 13/20 kW Turret 1 Number of tools: 8 Tool system according to DIN 69 880: 25 mm Indexing time for 1 station: 0.2 s Cross Slide 1 XZ Slide travel X-axis: 90 mm Slide travel Z-axis: 280 mm Feed force X-axis: 5,500 N Feed force Z-axis: 5,500 N Rapid traverse X-axis: 24 m/min Rapid traverse Z-axis: 24 m/min Resolution X-axis: 0.0005 mm Resolution Z-axis: 0.001 mm Turret 2 Number of tools: 6 Indexing time for 1 station: 0.25 s Cross Slide 2 XZ Slide travel X-axis: 81 mm Slide travel Z-axis: 80 mm Feed force X-axis: 8,300 N Feed force Z-axis: 5,500 N Rapid traverse X-axis: 16 m/min Rapid traverse Z-axis: 24 m/min Resolution X-axis: 0.0005 mm Resolution Z-axis: 0.001 mm Driven Tools Speed: max. 6,000 rpm Torque: max. 8 Nm Tool holder bore: 25.4 mm MACHINE DETAILS Control system: INDEX C200-4 Correction accuracy: 0.001 mm Input accuracy: 0.001 mm Output accuracy: 0.001 mm Coolant system Pump capacity: 60 l/min at 5.5 bar Pump capacity: 20 l/min at 20 bar Filling volume: approx. 210 l Hydraulics Delivery rate: 19 l/min System pressure: 90 bar Filling volume: 50 l Dimensions & Weight Footprint: 3,708 (2,495) × 1,240 mm Height: 1,750 mm Floor space requirement without material handling: 3,708 (2,495) × 1,890 mm Weight: approx. 2,500 kg Three-phase connection: 400 V, 50/60 Hz Connected power: 20–45 kVA Protection of the mains supply line: 35–80 A EQUIPMENT

Condition: ready for operation (used), Year of construction: 1999, travel distance X-axis: 190 mm, travel distance Z-axis: 350 mm, overall weight: 2,100 kg, number of axes: 2, This 2-axis Index ABC 63 was manufactured in 1999. It has a rated power of 13 kW and a machine weight of approximately 2100 kg. If you are looking to get high-quality turning capabilities, consider the Index ABC 63 horizontal turning machine we have for sale. Contact us for further details. Djdsy Iwrmepfx Al Asku • Mains voltage: 400 V • Control voltage: 24 V • Frequency: 50 Hz • Rated power: 13 kWThe Axis travels are approximetaly Technical Specification Counter Spindle No Driven Tools No

Condition: excellent (used), Year of construction: 2016, operating hours: 1,198 h, Brandt Ambition 1120 c edge banding machine with 2 glue tanks, joining, corner copying, and two trimming blades. A good entry-level machine with extensive features. A video of the machine in operation can be sent upon request. Edge thickness: approx. 0.4 - 3 mm Workpiece height: approx. 10 - 40 mm Feed rate: approx. 8 m/min Noise protection hood Extendable workpiece support Dust extraction connection: 1x100mm, 4x80mm, including the piping shown in the image, connected to 200mm Easy-Touch control with color screen for easy machine operation 10 programs can be saved Units: Upper pressure, manual adjustment with crank and SIKO counter Dodpezn Afpsfx Al Ajku Infeed guide, manual adjustment with SIKO counter Joining cutter with diamond cutters, sharpened A total of 2 interchangeable glue tanks for quick color changes from white to transparent Gluing section with automatic edge feeding for roll material up to 3 mm Pressing zone with 3 rollers Miter saw with 2 motors Combination milling unit, easily adjustable by hand for flush trimming, beveling, and rounding Corner rounding cutter R2 with diamond cutter, 1 motor-driven Radius trimming blade R2, manually adjustable Glue seam trimming blade with large roller, pneumatically controlled Hood locking mechanism CE marking Operating manual as a folder All indexable inserts of the milling units and trimming blades have been replaced or re-sharpened, saws have been sharpened, and diamond joining cutters have been sharpened. The machine is therefore ready for immediate use. Only the diamond cutter of the profile milling unit has not been replaced, but it is still sharp. Original paint, only a few spots have been touched up. Dust extraction hoses have been replaced. Approx. 1200 operating hours, i.e. only 1/2 hour per day. Machine dimensions approx. 4300 (with table) x 1250 x 1600 mm (LxWxH) Weight approx. 950 kg. The machine can be demonstrated on site by appointment. We only offer machines that are ready for demonstration and are in our warehouse, see "other offers from this provider".

Condition: used, Forkardt 2-Jaw Chuck 1629034, Double-Jaw Chuck, Ø 160mm Index G200 Adapter, Ø140mm ZWS140-K5 Index G200 Used, as shown in the pictures, in excellent condition From warehouse stock (may have storage marks) Dksdezk Iy Rspfx Al Aeu Please refer to the pictures for further technical information. Scope of delivery as shown in the pictures. With invoice. The invoice will be enclosed with the shipment.

Condition: used, Year of construction: 1996, functionality: limited functionality, travel distance X-axis: 630 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 650 mm, feed length X-axis: 630 mm, feed length Y-axis: 600 mm, feed length Z-axis: 650 mm, controller manufacturer: Fanuc, controller model: MSX-516, table width: 500 mm, table length: 500 mm, rotational speed (max.): 12,000 rpm, spindle speed (max.): 12,000 rpm, number of slots in tool magazine: 60, Equipment: chip conveyor, documentation/manual, We are offering this used MORI SEIKI SH-50 horizontal machining center, manufactured in 1996, for sale. Model designation: SH-50 Serial number: 450 The machine is currently powered and available for immediate delivery. • P8 power supply, valued at 1500, was renewed in August 2024. Dkodeyt Nnpspfx Al Aeu • The spindle was repaired in 2017 and has since been used primarily in a single-shift operation, as we mainly produce individual parts and small series. Therefore, the machine has spent most of its time in setup mode. • Machine: Mori Seiki SH50 milling machine • Control: Fanuc MSX-516 • Year of manufacture: 1996 • Configuration: Horizontal milling machine with indexing table • Tools: 60 (BT40) • Number of pallets: 2 (500mm * 500mm) • Travel: X 630mm, Y 600mm, Z 650mm • Spindle speed: 12,000 rpm • Chip conveyor Known defects: Rapid traverse of the X-axis has been reduced by 20% to extend the life of the telescopic covers. The sealing ring during pallet changes is likely damaged, resulting in oil leakage. We have temporarily resolved this by inserting a ball valve in between. We only need to open this when we change the pallets, which doesn't happen very often. The machine is sold as inspected, without any warranty or guarantee. Any liability for defects, including hidden defects, is excluded to the extent permitted by law. The magazine loses its reference point after being switched off for an extended period. The procedure for restoring it is known. If you have any questions or require further information, please send us a message or call us.

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,200 mm, travel distance Z-axis: 1,100 mm, table length: 4,500 mm, table width: 2,500 mm, spindle speed (max.): 22,000 rpm, CNC Heidenhain iTNC 640 WORKING AREA: Longitudinal X-axis travel: mm 4.000 Transversal Y-axis travel: mm 2.200 Vertical Z-axis travel: mm 1.100 Maximum speed with interpolating axes: m/min 50 WORKTABLE: Dimensions: mm 4.500 x 2.500 Height: mm 300 Load capacity: T/m² 15 T-slots for workpiece clamping mm 28 DIN 650 (H12), complete with leveling elements. T-slot direction parallel to Y-axis movement. CONTINUOUS POSITIONING UNIVERSAL HEAD WITH ELECTROSPINDLE: Automatic universal head indexed to 360,000 positions (every 0.001°). Rotation is driven by direct drive motors and controlled by the CNC as a positioning axis. Automatic tool clamping. Allows 10° undercut machining. Internal cooling system for bearings and axis motors. C-axis rotation range: ± 270° A-axis rotation range: ± 185° Maximum axis rotation speed: rpm 30 Maximum torque available on A/C axes: Nm 450 Axis clamping torque: Nm 1.400 Spindle power (S1/S6): kW 22/33 Spindle torque (S1/S6): Nm 84/128 Maximum spindle speed: rpm 22.000 Constant power range: rpm 3.000 to 18.000 Constant torque range: rpm 10 to 3.000 Tool interface: HSK-A63 DIN 69893 ELECTROSPINDLE HSK-A100 WITH SEMI-AUTOMATIC CHANGE SYSTEM Spindle power (S1/S6): kW 37/43 Spindle torque (S1/S6): Nm 140/165 Maximum spindle speed: rpm 15.000 Constant power range: rpm 2.500 to 12.000 Constant torque range: rpm 10 to 2.500 Tool interface: HSK-A100 DIN 69893 CHAIN TOOL MAGAZINE – 55 POSITIONS, HSK-A100 / HSK-A63 Floor-mounted fixed chain magazine located at the rear of the machine, fully enclosed for operator protection, equipped with a vertical tool change arm and automatic tool pre-selection. Fixed-pocket management system. Hydraulic axis locking Total tools: No. 55 HSK-A63 tools (DIN 69893): Number of tools: No. 30 Max tool diameter: mm 90 Max tool diameter (with adjacent pockets free): mm 160 Max tool length: mm 300 Max tool weight: kg 10 HSK-A100 tools (DIN 69893): Number of tools: No. 25 Max tool diameter: mm 100 Max tool diameter (with adjacent pockets free): mm 160 Max tool length: mm 450 Max tool weight: kg 20 REQUIRED CONNECTIONS Maximum installed power: kVA 177 Maximum current required: A 235 MACHINE EQUIPPED WITH: • Heidenhain HR550 remote electronic handwheel • High-pressure water and air through the spindle • Semi-automatic electrospindle change system with HSK-A63 and HSK-A100 interfaces • Various tooling included with the machine • Renishaw probe Dkodpfjyv In Iox Al Aju • BLUM laser presetting system • AUTOCAL automatic head calibration system • Visormax subscription for remote monitoring • Electrical cabinet air conditioning unit • Cooling system for all axes and the electrospindle • User and maintenance manual and CE declaration of conformity

Condition: used, Year of construction: 1987, Technical details: max. pitch circle diameter: 360/24 mm weight of the machine approx.: 46 kg centre height: 130 mm swivable: ja ° rotation movement: 360 Grad dimensions: 350 x 450 x 260 mm Application: For auxiliary work e.g. scribing of graduations. -dividing attachment with chuck Ø 125 in 360° pitch circle -clamping takes place via grid with index -pitch circle 24 -chuck: Ø 125mm, with revolving scale; through hole Ø 17mm; without jaws Dkodou Nlg Tspfx Al Aou -base plate: size 260 x 300mm, with 2 clamping grooves WxL: 15 x 21mm - chuck key - 2 pieces groove stone *

Condition: used, Year of construction: 2007, Machine No. 78, control system, manufacturer Boschert, tool quick-change system, manufacturer Trumpf, punching force: 3 x 280 kN, station 1 Trumpf system tool size 3 (105 mm) with spray device, station 2 Trumpf system tool size 3 (105 mm), freely indexable rotation, station 3 Trumpf system tool/Boschert Revotool size 3 (105 mm), including Revotool 8-position tool holder, travel distances X – 3,000 mm (adjustable up to 9,999 mm), Y – 1,580 mm, punching arm overhang 1,730 mm, sheet thickness max.: 6 mm (clamp opening), stroke height max.: 90 mm, programmable in increments upwards and downwards, punching slug extraction, ball bearings in the machine table Dkodpfjz Dv Tvjx Al Aou Table width left + right: 3,200 mm each, table depth: 2,810 mm, table height: 900 mm, overall width: 6,482 mm, overall depth: 4,600 mm, overall height: 2,110 mm; with workshop cart, manufacturer KS Tools, 7 drawers, contents: various hand tools.

Condition: used, Year of construction: 2001, functionality: fully functional, NC rotary table Fibro 10.36.8 with face gear, year 2001 well maintained, very good condition, little used Pitch 120 teeth +/- 1" With hydraulic locking via face gearing, table top does not lift off Dsdpfx Ajyg N Hrjl Asku Rotary table height 380 mm with substructure height 245 mm (total height 625 mm) Table size Ø 1180 mm Top table plate Ø 1300 mm, Table load approx. 5000 kg Table surface smooth, with dirt grooves with Siemens servo drive 1FT6105-8WF71-4EG2 and bevel gearbox Table speed max. 20 rpm with bevel gearboxes itot = 72 Tangential torque with motor operation 7200 Nm Total weight 3.800 kg without fixators, without installation and commissioning

Condition: excellent (used), functionality: fully functional, The dividing head is equipped with an SK40 spindle and has a spindle bore of 25mm. It can be swiveled from right to left up to 90° each. The dividing head spindle can be tilted 6°/15° from and towards the machine. It is suitable for all Deckel FP series milling machines and their "licensed machines," such as the Macmon M100. The distance from the spindle axis to the tailstock guide is 100mm. Direct division is possible using a 360° division circle or 24 x 15° indexing. The distance from the dividing head center to the tailstock center is 400mm. Indirect division is achieved with a worm gear of 40:1, using a scale disk with 1' division or three different hole disks (A: 27; 31; 34; 41; 43 – B: 33; 38; 39; 42; 46 – C: 36; 37; 40; 58). Djdpfx Aoz Hyyfjl Asku Also included are a Röhm four-jaw chuck, a three-jaw chuck (possibly Röhm) with adapter rings, and a two-jaw chuck, as well as a tailstock with a tailstock bearing. The dividing head, which was originally non-functional, along with all accessories, has been disassembled into individual parts, refurbished, made fully functional, and painted in two colors (RAL 7035 light gray / RAL 5004 dark blue). The dividing head is not in use and can be delivered immediately. Minor signs of wear from previous use are visible to a small extent. A single-use transport crate, with a total weight of 109 kg, has been prepared for transport. A manual compiled from Deckel descriptions is also included in the scope of delivery.

Year of construction: 2023, condition: used, functionality: fully functional, For sale: 300-liter vacuum concentrator – in almost new condition! Hagyo Vacuum Universal 300, an industrial vacuum concentrator manufactured in 2023, used only 10-12 times. Regularly serviced and ready for immediate operation. Vacuum concentration is an extremely gentle process: the water evaporates at a temperature below 50 °C, thus preserving the color, aroma, and nutritional values of the raw material, and the final product becomes much more enjoyable. Ideal for: concentrating pressed fruit juices to a jam-like consistency with a high refractive index, at low temperatures, without damaging the fiber and aroma characteristics, concentrating vegetable juices to a jam-like consistency (e.g., pumpkin, carrot, beetroot), extracting spices and herbs at low temperatures. Unique modifications made to this machine (not found on other machines in the series): high-performance defoaming unit, a 300-liter collection tank with a cleaning opening instead of the standard 100-liter tank, so the machine does not need to be stopped for emptying, new silicone elements on the mixing blade. Key features: 300-liter filling volume stainless steel construction, double-walled, with heating jacket mixing and vacuum system with automatic temperature control Dedpfxez Iwxnj Al Ajku stainless steel final cooler (condenser) built-in CIP cleaning system, each unit can be cleaned separately evaporation capacity: 30 l/hour (at 50 °C) electrical connection: 400 V, 38 kW (3×63 A) overall dimensions: 2000 × 1550 × 2550 mm Hungarian-language operating manual and machine documentation included Price: 12,000,000 HUF Viewings can be arranged in Szenna (Somogy County) by prior appointment. Reason for sale: change of business profile. Write a message, and I will send you more details!

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,200 mm, travel distance Z-axis: 1,100 mm, feed rate X-axis: 50 m/min, feed rate Y-axis: 50 m/min, feed rate Z-axis: 50 m/min, table length: 4,000 mm, table width: 2,000 mm, spindle speed (max.): 22,000 rpm, torque: 128 Nm, spindle nose: 63, CNC Heidenhain iTNC 530 S.P. WORKING AREA Longitudinal X-axis travel: mm 4.000 Transversal Y-axis travel: mm 2.200 Vertical Z-axis travel: mm 1.100 Maximum speed with interpolating axes: m/min 50 WORKTABLE Dimensions: mm 4.000 x 2.000 Height: mm 300 Load capacity: T/m² 15 T-slots for workpiece clamping mm 28 DIN 650 (H12), complete with leveling elements. T-slot direction parallel to X-axis movement. AXIS CHARACTERISTICS Axis feed rate: mm/min 50.000 Acceleration: m/s² 4 WORKING AREA (CLEARANCES) Maximum horizontal clearance: mm 3.200 Maximum vertical clearance under crossbeam: mm 1.926 Height of worktable from floor: mm 330 CONTINUOUS POSITIONING UNIVERSAL HEAD WITH ELECTROSPINDLE Automatic universal head indexed to 360,000 positions (every 0.001°). Rotation is driven by direct drive motors and controlled by the CNC as a positioning axis. Automatic tool clamping. Allows 10° undercut machining. Internal cooling system for bearings and axis motors. B-axis rotation range: ± 185° A-axis rotation range: ± 185° Maximum axis rotation speed: rpm 30 Maximum torque available on A/C axes: Nm 450 Axis clamping torque: Nm 1.400 Spindle power (S1/S6): kW 22/33 Spindle torque (S1/S6): Nm 84/128 Maximum spindle speed: rpm 22.000 Tool interface: HSK-A63 DIN 69893 The head is supplied complete with a cradle for handling and storage. The cradle is used outside the working area and therefore does not reduce the machine’s actual working capacity. CHAIN TOOL MAGAZINE – 30 POSITIONS (HSK) 30-position automatic chain tool changer located at the rear side of the working area, fully protected from dust and chips. Tool type: HSK-A63 DIN 69893 Max tool diameter (adjacent pockets occupied): mm 90 Max tool length: mm 300 Max tool weight: kg 10 MEASURING SCALE PRESSURIZATION Pneumatic system complete with control unit for pressurizing the measuring scales. SPRAY-MIST TOOL LUBRICATION/COOLING Mist lubrication system. The mist is generated by mixing air and oil and is controlled via M-function. The spray-mist improves cutting quality, prevents built-up edge formation, keeps the cutting area clean, and provides cooling. Highly effective for improving surface finish quality. EXTERNAL TOOL COOLING Coolant distribution system controlled by the CNC, with nozzles positioned on the flange around the spindle. Complete with a tank (1,200-liter capacity) for coolant collection and filtration. Flow rate: 30 l/min, pressure: 4 bar. REQUIRED CONNECTIONS Maximum installed power: kW 150 Maximum current required: A 235 MACHINE EQUIPPED WITH: • Heidenhain HR550 remote electronic handwheel • Various tooling included with the machine • Renishaw probe • BLUM laser presetting system Dedszb Evlepfx Al Aeku • AUTOCAL automatic head calibration system • Visormax subscription for remote monitoring • Electrical cabinet air conditioning unit • Cooling system for all axes and the electrospindle • No. 2 chip conveyors positioned on both sides of the worktable • User and maintenance manual and CE declaration of conformity

Condition: excellent (used), Index MS42C HBF rod guide Oil distributor Dsdpofdr R Ujfx Al Asku Flaps with tensioning screws

Condition: used, Year of construction: 2010, centre height 170 mm Dkjdjzwxyhopfx Al Aju Control CNC Achse rotary table dia. 180 mm total power requirement 2 kW weight of the machine ca. 92 kg dimensions of the machine ca. 0,6x0,35x0,4 m

Condition: used, Riveting machine, double riveting unit with rotary indexing table, DUNKES Type DN 4 Dedpfx Alsdzp T Ns Asku Rotary table, rotary indexing table with SIEMENS control Machine No. P 81 - 5458, Year of manufacture 1982 / 2009 Clamping force 40 kN Rivet shank diameter max. 12 mm Tool shank diameter 16 mm Overhang 190 mm Rivet head stroke per riveting unit approx. 60 mm Rivet spindle speed approx. 1400 rpm Installation height, tool - counter-tool max. 80 mm Compressed air requirement 6 bar Motor power per riveting unit 1.1 kW Mains connection 380 Volt, 50 Hz - Rotary table, indexing table with servo drive, step size programmable via Siemens PLC control - Double riveting unit is adjustable within the machine frame in relation to the rotary table - Table size Ø 295 mm for holding round workpieces - Pneumatic riveting stroke movement - Riveting unit adjustment via geared motor with lead screw, positioning via adjustable microswitch - Modernization of the control system and conversion of the servo drive in the rotary table in 2009 - New electrical control cabinet with Siemens Simatic Panel - Year of manufacture 2009 - Riveting time continuously programmable - Riveting pressure adjustment continuously adjustable via pressure gauge - Micrometer stop for limiting the stroke of the counter-rotating riveting units, 0-60 mm Space requirement L x W x H 3200 x 1250 x 2400 mm Weight approx. 2500 kg Good condition The machine was used for riveting segment saw blades from Ø 400 to Ø 2000 mm. The segments were manually placed on the support disc and fixed with straight rivet pins. The counter-rotating riveting unit rivets the pin simultaneously from both sides. The controlled table automatically rotates to the next working position. Ideal for saw blade manufacturers and repair companies. Or for the construction of a special machine. The riveting unit can also be easily removed and used as a conventional riveting machine by creating a suitable counter-tool.

Condition: used, Year of construction: 1997, Fully automatic index cutting machine Equipped with: Feeding Opening Counting/cutting 1 Counting/cutting 2 Printing station 1. colour Printing station 2. colour Delivery Technical data: Max. size: 185 x 130 mm Min. size: 50 x 60 mm Book thickness max. 15 mm (depending on product) Binding category: all standard binding sorts Cover bendable (no hardcover) Cut form angular cut Types Printing European/Arabic index combined indexes double and multiple indexes Printing: one or two colours letters and words Dksdpfsy Syulox Al Asu Dürrer promotional/explanatory video:

Condition: excellent (used), Year of construction: 2011, operating hours: 1,345 h, functionality: fully functional, travel distance X-axis: 1,250 mm, travel distance Y-axis: 1,100 mm, travel distance Z-axis: 1,050 mm, controller manufacturer: Fanuc, overall weight: 21,000 kg, number of slots in tool magazine: 60, Equipment: chip conveyor, documentation/manual, x-axis travel 1250 mm y-axis travel 1100 mm z-axis travel 1050 mm spindle speed range 8000 rpm spindle drive motor 30/22 kW pallet size 800 x 800 mm machine weight approx. 21 t machine dimensions approx. 5.0 x 8.0 x 4.0 m distance table / center of spindle 200 (100) - 1350 (1200) mm Torque Djdpfx Aljz H A S Dj Asku 600 tool taper 50 SK b-axis 0.001 ° table – indexing 90° in 2.5 sec. Control unit CNC Manufacturer of control unit FANUC 31i A

Condition: ready for operation (used), Year of construction: 1999, spindle speed (max.): 6,000 rpm, travel distance X-axis: 140 mm, travel distance Y-axis: 100 mm, travel distance Z-axis: 1,245 mm, spindle motor power: 9,400 W, total height: 2,100 mm, total width: 2,150 mm, overall weight: 8,330 kg, product length (max.): 7,250 mm, number of axes: 7, This 7-axis Index G300 L YB was manufactured in 1999. It features a maximum turning diameter of 270 mm and a maximum swing diameter of 590 mm. The machine includes a robust tool system with 12 stations and a milling spindle speed of up to 6000 rpm. If you are looking to get high-quality turning capabilities, consider the Index G300 L YB horizontal turning machine we have for sale. Contact us for further details. • Power supply: 3 phase / 50 Hz • Rated voltage: 400 V • Control voltage: 24 V • Rated current: 120 A • Rated power: 67 kW • Electrical cabinet weight: 710 kg • Spindle bore: 65 / 90 mm • Spindle bearing diameter (front): 110 / 140 mm • Spindle nose: ISO 702/1 size 6 / 8 • Chuck diameter: 200 / 250 / 315 mm • Maximum turning diameter: 270 mm • Maximum swing diameter: 590 mm • Power (100% duty cycle): 19 / 28 / 43 kW • Power (40% duty cycle): 28 / 40 / 57 kW • Torque (100% duty cycle): 120 / 178 / 275 Nm • Torque (40% duty cycle): 178 / 255 / 363 Nm • Maximum speed: 5000 / 3500 rpm • Counter spindle bore: 65 / 90 mm • Counter spindle bearing diameter: 110 / 140 mm • Counter spindle nose: ISO 702/1 size 6 / 8 • Counter spindle chuck diameter: 200 / 250 / 315 mm • Counter spindle power (100%): 19 / 28 kW • Counter spindle power (40%): 28 / 40 kW • Counter spindle torque (100%): 120 / 178 Nm • Counter spindle torque (40%): 178 / 255 Nm • Counter spindle max speed: 5000 / 3500 rpm • Minimum distance between spindles: 20 mm • Longitudinal travel: 770 / 1310 mm • Rapid traverse: 22.5 m/min Dkjdoyyyy Dspfx Al Asu • Rapid traverse X: 24 m/min • Rapid traverse Z: 30 m/min • Rapid traverse Y: 24 m/min • Tool system: VDI 30 • Number of tool stations: 12 • Max boring bar diameter: 50 mm • Milling spindle speed: up to 6000 rpm • Milling spindle power: 9.4 kW • Milling spindle torque: 19 Nm • Tailstock stroke: 630 mm • Tailstock quill diameter: 125 mm • Tailstock force: 7500 N • Hydraulic tank: 165 liters • Coolant tank: 300 liters Technical Specification Taper Size VDI 30 Counter Spindle Yes Driven Tools No

Condition: good (used), Index GE42 Tension cylinder GG2713.2101 Dsdpfx Aefbup Rel Aoku good condition

Condition: new, Feldmühle indexable inserts, ceramic, new, in original packaging SPUN 120308 Djdpfezuxlljx Al Asku TPGN 160312 F TPUN 16308 SCUN 120416 SNGN 12408

Condition: used, Year of construction: 2017, Rotary table, indexing table Manufacturer: Expert Tünkers Dksdpfx Aloyl Swwj Aeu Type: EDX810/0250/8 Year of manufacture: 2017 8-station table (45° increments) 51026